Sensitive and ultra-fast determination of arsenic(III) by gas-diffusion flow injection analysis with chemiluminescence detection

A novel chemiluminescence gas-diffusion flow injection system for the determination of arsenic(III) in aqueous samples is described. The analytical procedure involves injection of arsenic(III) samples and standards into a 0.3 mol L⁻¹ hydrochloric acid carrier stream which is merged with a reagent stream containing 0.2% (w/v) sodium borohydride and 0.015 mol L⁻¹ sodium hydroxide. Arsine, generated in the combined carrier/reagent donor stream, diffuses across the hydrophobic Teflon membrane of the gas-diffusion cell into an argon acceptor stream and then reacts with ozone in the flow-through chemiluminescence measuring cell of the flow system. Under optimal conditions, the method is characterized by a wide linear calibration range from 0.6 μg L⁻¹ to 25 mg L⁻¹, a detection limit of 0.6 μg L⁻¹ and a sample throughput of 300 samples per hour at 25 mg L⁻¹ and 450 samples per hour at 25 μg L⁻¹.     

Hybrid sequential injection-flow injection manifold for the spectrophotometric determination of total sulfite in wines using o-phthalaldehyde and gas-diffusion

A new automated spectrophotometric method for the determination of total sulfite in white and red wines is reported. The assay is based on the reaction of o-phthalaldehyde (OPA) and ammonium chloride with the analyte in basic medium under SI conditions. Upon on-line alkalization with NaOH, a blue product is formed having an absorption maximum at 630 nm. The parameters affecting the reaction - temperature, pH, ionic strength, amount concentration and volume of OPA, amount concentration of ammonium chloride, flow rate and reaction coil length - and the gas-diffusion process - sample and HCl volumes, length of mixing coil, donor flow rate - were studied. The proposed method was validated in terms of linearity (1-40 mg L⁻¹, r = 0.9997), limit of detection (c_L = 0.3 mg L⁻¹) and quantitation (c_Q = 1.0 mg L⁻¹), precision (s_r = 2.2% at 20 mg L⁻¹ sulfite, n = 12) and selectivity. The applicability of the analytical procedure was evaluated by analyzing white and red wine samples, while the accuracy as expressed by recovery experiments ranged between 96% and 106%.     

Sensitive determination of hydrazine in water by gas chromatography–mass spectrometry after derivatization with ortho-phthalaldehyde

A gas chromatography–mass spectrometric (GC–MS) method has been established for the determination of hydrazine in drinking water and surface water. This method is based on the derivatization of hydrazine with ortho-phthalaldehyde (OPA) in water. The following optimum reaction conditions were established: reagent dosage, 40 mg mL⁻¹ of OPA; pH 2; reaction for 20 min at 70 °C. The organic derivative was extracted with methylene chloride and then measured by GC–MS. Under the established condition, the detection and the quantification limits were 0.002 μg L⁻¹ and 0.007 μg L⁻¹ by using 5.0-mL of surface water or drinking water, respectively. The calibration curve showed good linearity with r² = 0.9991 (for working range of 0.05–100 μg L⁻¹) and the accuracy was in a range of 95–106%, and the precision of the assay was less than 13% in water. Hydrazine was detected in a concentration range of 0.05–0.14 μg L⁻¹ in 2 samples of 10 raw drinking water samples and in a concentration range of 0.09–0.55 μg L⁻¹ in 4 samples of 10 treated drinking water samples.     

Analysis of potassium formate in airport storm water runoff by headspace solid-phase microextraction and gas chromatography–mass spectrometry

Potassium formate was extracted from airport storm water runoff by headspace solid-phase microextraction (HS-SPME) and analyzed by GC–MS. Formate was transformed to formic acid by adding phosphoric acid. Subsequently, formic acid was derivatized to methyl formate by adding methanol. Using sodium [²H]formate (formate-d) as an internal standard, the relative standard deviation of the peak area ratio of formate (m/z 60) and formate-d (m/z 61) was 0.6% at a concentration of 208.5 mg L⁻¹. Calibration was linear in the range of 0.5–208.5 mg L⁻¹. The detection limit calculated considering the blank value was 0.176 mg L⁻¹. The mean concentration of potassium formate in airport storm water runoff collected after surface de-icing operations was 86.9 mg L⁻¹ (n = 11) with concentrations ranging from 15.1 mg L⁻¹ to 228.6 mg L⁻¹.     

Automatic flow system for the sequential determination of copper in serum and urine by flame atomic absorption spectrometry

In this work, a fully automated flow system exploiting the advantages of the association of multi-pumping, multicommutation, binary sampling and merging zones, to accomplish the sequential determination of copper in serum and urine by flame atomic absorption spectrometry, is described. The developed flow system allowed multiple tasks, such as serum samples preparation (samples and standard solutions viscosity adjustment), serum copper (SCu) measurement, urine copper (UCu) pre-concentration and its subsequent elution and measurement, to be carried out sequentially. The implemented flow manifold presented a modular configuration consisting on two quasi-independent modules, each one accountable for a specific sample manipulation and whose combined operation under computer control enabled the determination of copper in a wide concentrations range.Once optimised and with a sample consumption of about 0.250 mL of serum and 7 mL of urine, the developed flow system allowed linear calibration plots up to 5 mg L⁻¹ with a detection limit of 0.035 mg L⁻¹ for SCu and linear calibration plots up to 300 μg L⁻¹ with a detection limit of 0.67 μg L⁻¹ for UCu. The sampling rate varied according to the module employed and was about 360 determinations h⁻¹ (SCu module), 12 determinations h⁻¹ (UCu module) or 24 determinations h⁻¹ (12 urine and 12 serum samples; UCu and SCu modules simultaneously). Repeatability studies (R.S.D.%, n = 10) showed good precision for UCu at concentrations of 25 μg L⁻¹ (2.54%), 50 μg L⁻¹ (0.90%) and 100 μg L⁻¹ (1.62%) as well as for SCu at concentrations of 0.25 mg L⁻¹ (8.11%), 1 mg L⁻¹ (3.11%) and 5 mg L⁻¹ (0.90%). A comparative evaluation showed a good agreement between the results obtained in the analysis of UCu and SCu (n = 18) by both the developed methodology and the reference procedures. Accuracy was further evaluated by means of the analysis of reference samples (Seronorm™ Trace Elements Urine and Seronorm™ Trace Elements Serum) and the obtained results complied with the certified values.     

Evaluation of alternate lines of Fe for sequential multi-element determination of Cu, Fe, Mn and Zn in soil extracts by high-resolution continuum source flame atomic absorption spectrometry

The usefulness of the secondary line at 252.744 nm and the approach of side pixel registration were evaluated for the development of a method for sequential multi-element determination of Cu, Fe, Mn and Zn in soil extracts by high-resolution continuum source flame atomic absorption spectrometry (HR-CS FAAS). The influence of side pixel registration on the sensitivity and linearity was investigated by measuring at wings (248.325, 248.323, 248.321, 248.329, and 248.332 nm) of the main line for Fe at 248.327 nm. For the secondary line at 252.744 nm or side pixel registration at 248.325 nm, main lines for Cu (324.754 nm), Mn (279.482 nm) and Zn (213.875 nm), sample flow-rate of 5.0 mL min⁻¹ and calibration by matrix matching, analytical curves in the 0.2-1.0 mg L⁻¹ Cu, 1.0-20.0 mg L⁻¹ Fe, 0.2-2.0 mg L⁻¹ Mn, 0.1-1.0 mg L⁻¹ Zn ranges were obtained with linear correlations better than 0.998. The proposed method was applied to seven soil samples and two soil reference materials (IAC 277; IAC 280). Results were in agreement at a 95% confidence level (paired t-test) with reference values. Recoveries of analytes added to soil extracts containing 0.15 and 0.30 mg L⁻¹ Cu, 7.0 and 14 mg L⁻¹ Fe, 0.60 and 1.20 mg L⁻¹ Mn, 0.07 and 0.15 mg L⁻¹ Zn, varied within the 94-99, 92-98, 93-101, and 93-103% intervals, respectively. The relative standard deviations (n = 12) were 2.7% (Cu), 1.4% (Fe - 252.744 nm), 5.7% (Fe - 248.325 nm), 3.2% (Mn) and 2.8% (Zn) for an extract containing 0.35 mg L⁻¹ Cu, 14 mg L⁻¹ Fe, 1.1 mg L⁻¹ Mn and 0.12 mg L⁻¹ Zn. Detection limits were 5.4 μg L⁻¹ Cu, 55 μg L⁻¹ Fe (252.744 nm), 147 μg L⁻¹ Fe (248.325 nm), 3.0 μg L⁻¹ Mn and 4.2 μg L⁻¹ Zn.     

Sequential injection methodology for carbon speciation in bathing waters

A sequential injection method (SIA) for carbon speciation in inland bathing waters was developed comprising, in a single manifold, the determination of dissolved inorganic carbon (DIC), free dissolved carbon dioxide (CO₂), total carbon (TC), dissolved organic carbon and alkalinity. The determination of DIC, CO₂ and TC was based on colour change of bromothymol blue (660 nm) after CO₂ diffusion through a hydrophobic membrane placed in a gas diffusion unit (GDU). For the DIC determination, an in-line acidification prior to the GDU was performed and, for the TC determination, an in-line UV photo-oxidation of the sample prior to GDU ensured the conversion of all carbon forms into CO₂. Dissolved organic carbon (DOC) was determined by subtracting the obtained DIC value from the TC obtained value. The determination of alkalinity was based on the spectrophotometric measurement of bromocresol green colour change (611 nm) after reaction with acetic acid. The developed SIA method enabled the determination of DIC (0.24–3.5 mg C L⁻¹), CO₂ (1.0–10 mg C L⁻¹), TC (0.50–4.0 mg C L⁻¹) and alkalinity (1.2–4.7 mg C L⁻¹ and 4.7–19 mg C L⁻¹) with limits of detection of: 9.5 μg C L⁻¹, 20 μg C L⁻¹, 0.21 mg C L⁻¹, 0.32 mg C L⁻¹, respectively. The SIA system was effectively applied to inland bathing waters and the results showed good agreement with reference procedures.     

Assessment of cadmium and iron adsorption in sediment,employing a flow injection analysis system with on line filtration and detection by flame atomic absorption spectrometry and thermospray flame furnace atomic absorption spectrometry

This work presents an evaluation of iron and cadmium adsorption in sediment of the Furnas Hydroelectric Plant Reservatory located in Alfenas, Minas Gerais (Brazil). The metal determination was done employing a flow injection analysis (FIA) with an on-line filtering system. As detection techniques, flame atomic absorption spectrometry (FAAS) for iron and thermospray flame furnace atomic absorption spectrometry (TS-FF-AAS) for cadmium determinations were used. The developed methodology presented good limits of detection, being 190 μg L⁻¹ for iron and 1.36 μg L⁻¹ for cadmium, and high sampling frequency for both metals 144 and 60 readings h⁻¹ for iron and cadmium, respectively. Both metals obey the Langmuir model, with maximum adsorptive capacity of 0⋅169 mg g⁻¹ for iron and 7⋅991 mg g⁻¹ for cadmium. For iron, a pseudo-first-order kinetic model was obtained with a theoretical Q_e = 9⋅8355 mg g⁻¹ (experimental Q_e = 9⋅5432 mg  g⁻¹), while for cadmium, a pseudo-second-order kinetic model was obtained, with a theoretical Q_e = 0.3123 mg g⁻¹ (experimental Q_e = 0⋅3052 mg g⁻¹).     

Selective fluorimetric method for the determination of histamine in seafood samples based on the concept of zone fluidics

In the present article we report our results on the development of a selective automated method for the determination of histamine in seafood using the concept of zone fluidics. The method is based on the sequential on-line reaction of the analyte with o-phthalaldehyde in the absence of a nucleophilic reagent, followed by acidification. The careful selection of the chemical and instrumental variables enabled the determination of the analyte with adequate sensitivity at the low micromolar level and with specificity against other biogenic amines and amino acids such as histidine. The LOD was 0.05 μmol L⁻¹ (0.6 mg kg⁻¹) and linearity was obeyed in the range of 0.5–15 μmol L⁻¹ (5.5–170 mg kg⁻¹). The proposed method offers a satisfactory sampling rate of 15 h⁻¹ and adequate accuracy and precision for the analysis of seafood products after minimum sample preparation and without employing a separation technique.     

A flow injection procedure based on solenoid micro-pumps for spectrophotometric determination of free glycerol in biodiesel

A flow system designed with solenoid micro-pumps is proposed for fast and greener spectrophotometric determination of free glycerol in biodiesel. Glycerol was extracted from samples without using organic solvents. The determination involves glycerol oxidation by periodate, yielding formaldehyde followed by formation of the colored (3,5-diacetil-1,4-dihidrolutidine) product upon reaction with acetylacetone. The coefficient of variation, sampling rate and detection limit were estimated as 1.5% (20.0 mg L⁻¹ glycerol, n = 10), 34 h⁻¹, and 1.0 mg L⁻¹ (99.7% confidence level), respectively. A linear response was observed from 5 to 50 mg L⁻¹, with reagent consumption estimated as 345 μg of KIO₄ and 15 mg of acetylacetone per determination. The procedure was successfully applied to the analysis of biodiesel samples and the results agreed with the batch reference method at the 95% confidence level.     

Selective determination of cyanides by gas diffusion-stopped flow-sequential injection analysis and an on-line standard addition approach

A highly selective sequential injection (SI) method for the automated determination of weak-acid-dissociable cyanides is reported. The analytical procedure is based on the on-line reaction of the analyte with ninhydrin in carbonate medium to form a coloured product (λ_max = 510 nm). Cyanides are removed from sample matrix by acidification through a gas-diffusion step incorporated in the SI manifold. The effect of instrumental and chemical variables was studied. By adopting an on-line standard addition protocol, the sensitivity of the proposed method was enhanced drastically, without affecting the determination range. The assay was validated in terms of linearity (up to 200 μg L⁻¹), limit of detection (c_L = 2.5 μg L⁻¹), limit of quantitation (c_Q = 7.5 μg L⁻¹), precision (s_r < 2.5% at 100 μg L⁻¹) and selectivity. High tolerance against critical species such as sulfides and thiocyanates was achieved. The applicability of the method was demonstrated by analyzing tap and mineral water samples at levels below the limits established by international E.U. and U.S. organizations. The percent recoveries were satisfactory in all cases, ranging between 94.2 and 103.6%.     

Analysis of aldehydes in beer by gas-diffusion microextraction: Characterization by high-performance liquid chromatography–diode-array detection–atmospheric pressure chemical ionization–mass spectrometry

In this work, a recently developed extraction technique for sample preparation aiming the analysis of volatile and semi-volatile compounds named gas-diffusion microextraction (GDME) is applied in the chromatographic analysis of aldehydes in beer. Aldehydes—namely acetaldehyde (AA), methylpropanal (MA) and furfural (FA)—were simultaneously extracted and derivatized with 2,4-dinitrophenylhydrazine (DNPH), then the derivatives were separated and analyzed by high-performance liquid chromatography with spectrophotometric detection (HPLC–UV). The identity of the eluted compounds was confirmed by high-performance liquid chromatography–atmospheric pressure chemical ionization–mass-spectrometry detection in the negative ion mode (HPLC–APCI–MS). The developed methodology showed good repeatability (ca. 5%) and linearity as well as good limits of detection (AA–12.3, FA–1.5 and MA 5.4 μg L⁻¹) and quantification (AA–41, FA–4.9 and MA 18 μg L⁻¹); it also appears to be competitive in terms of speed and cost of analysis.     

Sensitive determination of fluoride in biological samples by gas chromatography–mass spectrometry after derivatization with 2-(bromomethyl)naphthalene

A gas chromatography–mass spectrometric method was developed in this study in order to determine fluoride in plasma and urine after derivatization with 2-(bromomethyl)naphthalene. 2-Fluoronaphthalene was chosen as the internal standard. The derivatization of fluoride was performed in the biological sample and the best reaction conditions (10.0 mg mL⁻¹ of 2-(bromomethyl)naphthalene, 1.0 mg mL⁻¹ of 15-crown-5-ether as a phase transfer catalyst, pH of 7.0, reaction temperature of 70 °C, and heating time of 70 min) were established. The organic derivative was extracted with dichloromethane and then measured by a gas chromatography–mass spectrometry. Under the established condition, the detection limits were 11 μg L⁻¹ and 7 μg L⁻¹ by using 0.2 mL of plasma or urine, respectively. The accuracy was in a range of 100.8–107.6%, and the precision of the assay was less than 4.3% in plasma or urine. Fluoride was detected in a concentration range of 0.12–0.53 mg L⁻¹ in six urine samples after intake of natural mineral water containing 0.7 mg L⁻¹ of fluoride.     

New procedure of selected biogenic amines determination in wine samples by HPLC

A new procedure for determination of biogenic amines (BA): histamine, phenethylamine, tyramine and tryptamine, based on the derivatization reaction with 2-chloro-1,3-dinitro-5-(trifluoromethyl)-benzene (CNBF), is proposed. The amines derivatives with CNBF were isolated and characterized by X-ray crystallography and ¹H, ¹³C, ¹⁹F NMR spectroscopy in solution. The novelty of the procedure is based on the pure and well-characterized products of the amines derivatization reaction. The method was applied for the simultaneous analysis of the above mentioned biogenic amines in wine samples by the reversed phase-high performance liquid chromatography. The procedure revealed correlation coefficients (R²) between 0.9997 and 0.9999, and linear range: 0.10–9.00 mg L⁻¹ (histamine); 0.10–9.36 mg L^-1 (tyramine); 0.09–8.64 mg L⁻¹ (tryptamine) and 0.10–8.64 mg L⁻¹ (phenethylamine), whereas accuracy was 97%–102% (recovery test). Detection limit of biogenic amines in wine samples was 0.02–0.03 mg L⁻¹, whereas quantification limit ranged 0.05–0.10 mg L⁻¹. The variation coefficients for the analyzed amines ranged between 0.49% and 3.92%. Obtained BA derivatives enhanced separation the analytes on chromatograms due to the inhibition of hydrolysis reaction and the reduction of by-products formation.     

Direct quantification of creatinine in human urine by using isotope dilution extractive electrospray ionization tandem mass spectrometry

Urinary creatinine (CRE) is an important biomarker of renal function. Fast and accurate quantification of CRE in human urine is required by clinical research. By using isotope dilution extractive electrospray ionization tandem mass spectrometry (EESI–MS/MS) a high throughput method for direct and accurate quantification of urinary CRE was developed in this study. Under optimized conditions, the method detection limit was lower than 50 μg L⁻¹. Over the concentration range investigated (0.05–10 mg L⁻¹), the calibration curve was obtained with satisfactory linearity (R² = 0.9861), and the relative standard deviation (RSD) values for CRE and isotope-labeled CRE (CRE-d3) were 7.1–11.8% (n = 6) and 4.1–11.3% (n = 6), respectively. The isotope dilution EESI–MS/MS method was validated by analyzing six human urine samples, and the results were comparable with the conventional spectrophotometric method (based on the Jaffe reaction). Recoveries for individual urine samples were 85–111% and less than 0.3 min was taken for each measurement, indicating that the present isotope dilution EESI–MS/MS method is a promising strategy for the fast and accurate quantification of urinary CRE in clinical laboratories.     

Sequential injection method for the direct spectrophotometric determination of bismuth in pharmaceutical products

A spectrophotometric method is reported for the determination of bismuth in pharmaceutical products using sequential injection analysis. Methylthymol blue (MTB) was used as a color forming reagent and the absorbance of the Bi(III)-MTB complex was monitored at 548 nm. The various chemical and physical variables that affected the reaction were studied. A linear calibration graph was obtained in the range 0.0-75.0 mg l⁻¹ Bi(III) at a sampling frequency of 72 h⁻¹. The reagent consumption was considerably reduced compared to conventional flow injection systems, as only 150 μl of MTB were consumed per run. The precision was very satisfactory (s_r=0.5%, at 50.0 mg l⁻¹ Bi(III), n=12) and the limit of detection, c_L, was 0.250 mg l⁻¹. The developed method was applied successfully to the analysis of various pharmaceutical products containing Bi(III). The relative errors e_r, were <1.5% in all cases and were evaluated by comparison of the obtained results with those found using atomic absorption spectrometry as the reference method.     

Sample cleanup-free determination of mycophenolic acid and its glucuronide in serum and plasma using the novel technology of ultra-performance liquid chromatography-electrospray ionization tandem mass spectrometry

Mycophenolic acid (MPA) is an immunosuppressant drug which powerfully inhibits lymphocyte proliferation. Since the early 1990s it has been used to prevent rejection in organ transplantation. The requirement of therapeutic drug monitoring shown in previous studies raises the necessity of acquiring accurate and sensitive methods to measure MPA and its major metabolite mycophenolic acid glucuronide (MPAG).The authors developed a sample cleanup-free, rapid, and highly specific method for simultaneous measurement of MPA and MPAG in human plasma and serum using the novel technology of ultra-performance liquid chromatography-electrospray ionization tandem mass spectrometry. MPA- and MPAG-determinations were performed during a 2.0-min run time. Multiple calibration curves for the analysis of MPA and MPAG exhibited consistent linearity and reproducibility in the range of 0.05-100 (r > 0.999) mg L⁻¹ and 4-4000 mg L⁻¹ (r > 0.999), respectively. Limits of Detection were 0.014 mg L⁻¹ for MPA and 1.85 mg L⁻¹ for MPAG. Lower Limits of Quantification were 0.05 mg L⁻¹ for MPA and 2.30 mg L⁻¹ for MPAG. Interassay imprecision was <10% for both substances. Mean recovery was 103.6% (range 78.1-129.7%) for MPA and 111.1% (range 73.0-139.6%) for MPAG. Agreement was good for MPA and MPAG between the presented method and a validated HPLC-MS/MS method. The Passing-Bablok regression line for MPA and MPAG was HPLC-MS/MS = 1.14 UPLC-MS/MS—0.14 [mg L⁻¹], r = 0.96, and HPLC-MS/MS = 0.77 UPLC-MS/MS + 0.50 [mg L⁻¹], r = 0.97, respectively. This sample cleanup-free and robust LC-MS/MS assay facilitates the rapid, accurate and simultaneous determination of MPA and MPAG in human body fluids.     

The use of a polymer inclusion membrane for separation and preconcentration of orthophosphate in flow analysis

A highly sensitive flow analysis system has been developed for the trace determination of reactive phosphate in natural waters, which uses a polymer inclusion membrane (PIM) with Aliquat 336 as the carrier for on-line analyte separation and preconcentration. The system operates under flow injection (FI) and continuous flow (CF) conditions. Under optimal FI conditions the system is characterised by a linear concentration range between 0.5 and 1000 μg L⁻¹ P, a sampling rate of 10 h⁻¹, a limit of detection of 0.5 μg L⁻¹ P and RSDs of 3.2% (n = 10, 100 μg L⁻¹) and 7.7% (n = 10, 10 μg L⁻¹). Under CF conditions with 10 min stop-flow time and sample solution flow rate of 1.32 mL min⁻¹ the flow system offers a limit of detection of 0.04 μg L⁻¹ P, a sampling rate of 5 h⁻¹ and an RSD of 3.4% (n = 5, 2.0 μg L⁻¹). Interference studies revealed that anions commonly found in natural waters did not interfere when in excess of at least one order of magnitude. The flow system, operating under CF conditions, was successfully applied to the analysis of natural water samples containing concentrations of phosphate in the low μg L⁻¹ P range, using the multipoint standard addition method.     

Highly selective flow injection spectrophotometric determination of gold based on its catalytic effect on the oxidation of variamine blue by potassium iodate in aqueous N,N-dimethylformamide medium

A highly selective and simple flow injection method is reported for the determination of Au(III) in jewel samples. The method is based on the catalytic effect of Au(III) on the oxidation of 4-amino-4′-methoxydiphenylamine hydrochloride (Variamine Blue B base, VB) by KIO₃. The colored reaction product was monitored spectrophotometrically at 546 nm. A volume fraction of 40% N,N-dimethylformamide (DMF) greatly enhances the selectivity of the method. The chemical (pH and concentrations of reagents) and instrumental variables (sample injection volume, reagents flow rates, reaction coil length) affecting the determination were studied and optimized. Under the selected values, the analyte could be determined in the range of 0.1-12.0 mg L⁻¹ (r = 0.9997), at a sampling rate of 120 h⁻¹. The proposed assay was precise (s_r = 0.8% at 5.0 mg L⁻¹ Au(III), n = 12) and adequately sensitive with a 3σ limit of detection of 0.03 mg L⁻¹. The method was successfully applied to the analysis of jewel samples. The obtained results were favorably compared to flame atomic absorption spectrometry (FAAS) used as a reference method.     

Determination of picloram in natural waters employing sequential injection square wave voltammetry using the hanging mercury drop electrode

This paper describes the development of a sequential injection analysis method to automate the determination of picloram by square wave voltammetry exploiting the concept of monosegmented flow analysis to perform in-line sample conditioning and standard addition. To perform these tasks, an 800 μL monosegment is formed, composed by 400 μL of sample and 400 μL of conditioning/standard solution, in medium of 0.10 mol L⁻¹ H₂SO₄. Homogenization of the monosegment is achieved by three flow reversals. After homogenization the mixture zone is injected toward the flow cell, which is adapted to the capillary of a hanging drop mercury electrode, at a flow rate of 50 μL s⁻¹. After a suitable delay time, the potential is scanned from −0.5 to −1.0 V versus Ag/AgCl at frequency of 300 Hz and pulse height of 25 mV. The linear dynamic range is observed for picloram concentrations between 0.10 and 2.50 mg L⁻¹ fitting to the linear equation I_p = (−2.19 ± 0.03)C_picloram + (0.096 ± 0.039), with R² = 0.9996, for which the slope is given in μA L mg⁻¹. The detection and quantification limits are 0.036 and 0.12 mg L⁻¹, respectively. The sampling frequency is 37 h⁻¹ when the standard addition protocol is followed, but can be increased to 41 h⁻¹ if the protocol to obtain in-line external calibration curve is used for quantification. The method was applied for determination of picloram in spiked water samples and the accuracy was evaluated by comparison with high performance liquid chromatography using molecular absorption at 220 nm for detection. No evidences of statistically significant differences between the two methods were observed.