Electrochemical sensing platform based on covalent immobilization of thionine onto gold electrode surface via diazotization-coupling reaction

A novel electrochemical sensing platform by modification of electroactive thionine (Th) onto gold electrode surface was constructed, which was realized by diazotization of 4-aminothiophenol (ATP) self-assembled monolayer, followed by coupling of Th with the diazonium group to form a covalent diazo bond. A pair of well-defined redox peaks of Th was observed in the cyclic voltammetric measurement. The resulting diazo-ATP monolayer displayed superior electrical conductivity, which contributed to the sensitive detection of hydrogen peroxide (H₂O₂). The immobilized Th also showed a remarkable stability, which may benefit from the π-π stacking force and the covalent diazo bond between diazo-ATP and Th molecules. Under the optimized experimental conditions, the current fabricated non-enzyme and reagentless sensor could show a rapid response to H₂O₂ within 3 s and a linear calibration plot ranged from 1.0 × 10⁻⁶ to 6.38 × 10⁻³ M with a detection limit of 6.7 × 10⁻⁷ M. The current fabrication strategy of electroactive interface is expected to be used as a versatile route for the immobilization of more electroactive molecules and offer more opportunities for the applications in electrochemical sensor, biosensor, electrocatalysis, etc.     

A novel nonenzymatic sensor based on LaNi0.6Co0.4O3 modified electrode for hydrogen peroxide and glucose

In this paper, LaNi_0.6Co_0.4O₃ (LNC) nanoparticles were synthesized by the sol–gel method, and the structure and morphology of LNC nanoparticles were characterized by X-ray diffraction spectrum, scanning electron microscopy and transmitting electron microscopy. And then, LNC was used to modify carbon paste electrode (CPE) without any adhesive to fabricate hydrogen peroxide and glucose sensor, and the results demonstrated that LNC exhibited strong electrocatalytical activity by cyclic voltammetry and amperometry. In H₂O₂ determination, linear response was obtained in the concentration range of 10 nM–100 μM with a detection limit of 1.0 nM. In glucose determination, there was the linear region of 0.05–200 μM with a detection limit of 8.0 nM. Compared with other reports, the proposed sensor also displayed high sensitivity toward H₂O₂ (1812.84 μA mM⁻¹ cm⁻²) and glucose (643.0 μA mM⁻¹ cm⁻²). Moreover, this prepared sensor was applied to detect glucose in blood serum and hydrogen peroxide in toothpaste samples with satisfied results, indicating its possibility in practical application.     

Polyphosphonate induced coacervation of chitosan: Encapsulation of proteins/enzymes and their biosensing

Based on the polyphosphonate-assisted coacervation of chitosan, a simple and versatile procedure for the encapsulation of proteins/enzymes in chitosan–carbon nanotubes (CNTs) composites matrix was developed. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), energy dispersive spectrum (EDS) mapping demonstrated the hemoglobin (Hb) uniformly distributed into chitosan–CNTs composites matrix. Raman measurements indicated the CNTs in composites matrix retained the electronic and structural integrities of the pristine CNTs. Fourier transform infrared (FT-IR), ultraviolet–visible (UV–vis) and circular dichroism (CD) spectroscopy displayed the encapsulated Hb preserved their near-native structure, indicating the polyphosphonate–chitosan–CNTs composites possessed excellent biocompatibility for the encapsulation of proteins/enzymes. Electrochemical measurements indicated the encapsulated Hb could directly exchange electron with the substrate electrode. Moreover, the modified electrode showed excellent bioelectrocatalytic activity for the reduction of hydrogen peroxide. Under optimum experimental conditions, the fabricated electrochemical sensor displayed the fast response (less than 3 s), wide linear range (7.0 × 10⁻⁷ to 2.0 × 10⁻³ M) and low detection limit (4.0 × 10⁻⁷ M) for the determination of hydrogen peroxide. This newly developed protocol was simple and mild and would certainly find extensive applications in biocatalysis, biosensors, bioelectronics and biofuel cells.     

Immobilization of [Cu(bpy)2]Br2 complex onto a glassy carbon electrode modified with α-SiMo12O40 and single walled carbon nanotubes: Application to nanomolar detection of hydrogen peroxide and bromate

A simple procedure has been used for preparation of modified glassy carbon electrode with carbon nanotubes and copper complex. Copper complex [Cu(bpy)₂]Br₂ was immobilized onto glassy carbon (GC) electrode modified with silicomolybdate, α-SiMo₁₂O₄₀⁴⁻ and single walled carbon nanotubes (SWCNTs)_. Copper complex and silicomolybdate irreversibly and strongly adsorbed onto GC electrode modified with CNTs. Electrostatic interactions between polyoxometalates (POMs) anions and Cu-complex, cations mentioned as an effective method for fabrication of three-dimensional structures. The modified electrode shows three reversible redox couples for polyoxometalate and one redox couple for Cu-complex at wide range of pH values. The electrochemical behavior, stability and electron transfer kinetics of the adsorbed redox couples were investigated using cyclic voltammetry. Due to electrostatic interaction, copper complex immobilized onto GC/CNTs/α-SiMo₁₂O₄₀⁴⁻ electrode shows more stable voltammetric response compared to GC/CNTs/Cu-complex modified electrode. In comparison to GC/CNTs/Cu-complex the GC/CNTs/α-SiMo₁₂O₄₀⁴⁻ modified electrodes shows excellent electrocatalytic activity toward reduction H₂O₂ and BrO₃⁻ at more reduced overpotential. The catalytic rate constants for catalytic reduction hydrogen peroxide and bromate were 4.5(±0.2) × 10³ M⁻¹ s⁻¹ and 3.0(±0.10) × 10³ M⁻¹ s⁻¹, respectively. The hydrodynamic amperommetry technique at 0.08 V was used for detection of nanomolar concentration of hydrogen peroxide and bromate. Detection limit, sensitivity and linear concentration range proposed sensor for bromate and hydrogen peroxide detection were 1.1 nM and 6.7 nA nM⁻¹, 10 nM-20 μM, 1 nM, 5.5 nA nM⁻¹ and 10 nM-18 μM, respectively.     

Biomimetic sensor based on MnMn complex as manganese peroxidase mimetic for determination of rutin

A novel biomimetic sensor for rutin determination based on a dinuclear complex [Mn^IIIMn^II(Ldtb)(μ-OAc)₂]BPh₄ containing an unsymmetrical dinucleating ligand, 2-[N,N-bis(2-pyridylmethyl)-aminomethyl]-6-[N-(3,5-di-tert-butyl-2-oxidoben-zyl)-N-(2-pyridylamino)aminomethyl]-4-methylphenol (H₂Ldtb), as a manganese peroxidase mimetic was developed. Several parameters were investigated to evaluate the performance of the biomimetic sensor obtained after the incorporation of the dinuclear complex in a carbon paste. The best performance was obtained in 75:15:10% (w/w/w) of the graphite powder:Nujol:Mn^IIIMn^II complex, 0.1 mol L⁻¹ phosphate buffer solution (pH 6.0) and 4.0 × 10⁻⁵ mol L⁻¹ hydrogen peroxide. The response of the sensor towards rutin concentration was linear using square wave voltammetry in the range of 9.99 × 10⁻⁷ to 6.54 × 10⁻⁵ mol L⁻¹ (r = 0.9998) with a detection limit of 1.75 × 10⁻⁷ mol L⁻¹. The recovery study performed with pharmaceuticals ranged from 96.6% to 103.2% and the relative standard deviation was 1.85% for a solution containing 1.0 × 10⁻³ mol L⁻¹ rutin (n = 6). The lifetime of this biomimetic sensor was 200 days (at least 750 determinations). The results obtained for rutin in pharmaceuticals using the biomimetic sensor and those obtained with the official method are in agreement at the 95% confidence level.     

Sensors based on galvanic cell generated electrochemiluminescence and its application

In this paper, a novel electrochemiluminescence (ECL) imaging sensor array was developed for determination of hydrogen peroxide (H₂O₂), which was based on Cu/Zn alloy galvanic cell generated ECL. In alkaline solution, Cu/Zn galvanic cell was formed because of corrosion effect, the galvanic cell could supply stable potential for ECL generation of luminol, and the weak ECL emission could be enhanced by H₂O₂. The galvanic cell sensor array was designed by putting Cu/Zn alloy in 96-well microtiter plates separately. The relative ECL intensity was proportional with the concentration of hydrogen peroxide in the range of 1.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol l⁻¹ and the detection limit was 3.0 × 10⁻⁷ mol l⁻¹ (3σ), the relative standard deviation (R.S.D.) for 11 parallel measurements of 1.0 × 10⁻⁵ mol l⁻¹ H₂O₂ was 4.0%.     

Highly accessible Pt nanodots homogeneously decorated on Au nanorods surface for sensing

Some nanostructures are reported to possess enzyme-mimetic activities similar to those of natural enzymes. Herein, highly-dispersed Pt nanodots on Au nanorods (HD- PtNDs@AuNRs) with mimetic peroxidase activity were designed as an active electrode modifier for fabrication of a hydrogen peroxide (H₂O₂) electrochemical sensor. The HD-PtNDs@AuNRs were synthesized by a seed-mediated growth approach and confirmed by scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy, and UV–vis spectroscopy. The electrochemical and catalytical performances of HD-PtNDs@AuNRs towards H₂O₂ reduction were investigated in detail by cyclic voltammetry and amperometry. The HD-PtNDs@AuNRs modified electrode displayed a high catalytic activity to H₂O₂ at −0.10 V (versus SCE), a rapid response within 5 s, a wide linear range of 2.0–3800.0 μM, a detection limit of 1.2 μM (S/N = 3), and a high sensitivity of 181 μA mM⁻¹ cm⁻². These results suggested a promising potential of fabricating H₂O₂ electrochemical sensor using HD- PtNDs@AuNRs.     

Disposable biosensor based on cathodic electrochemiluminescence of tris(2,2-bipyridine)ruthenium(II) for uric acid determination

A new method for uric acid (UA) determination based on the quenching of the cathodic ECL of the tris(2,2-bipyridine)ruthenium(II)–uricase system is described. The biosensor is based on a double-layer design containing first tris(2,2-bipyridine)ruthenium(II) (Ru(bpy)₃²⁺) electrochemically immobilized on graphite screen-printed cells and uricase in chitosan as a second layer. The uric acid biosensing is based on the ECL quenching produced by uric acid over the cathodic ECL caused by immobilized Ru(bpy)₃²⁺ in the presence of uricase. The use of a −1.1 V pulse for 1 s with a dwelling time of 10 s makes it possible to estimate the initial enzymatic rate, which is used as the analytical signal. The Stern–Volmer type calibration function shows a dynamic range from 1.0 × 10⁻⁵ to 1.0 × 10⁻³ M with a limit of detection of 3.1 × 10⁻⁶ M and an accuracy of 13.6% (1.0 × 10⁻⁴ M, n = 5) as relative standard deviation. Satisfactory results were obtained for urine samples, creating an affordable alternative for uric acid determination.     

A hydrogen peroxide biosensor based on Langmuir-Blodgett technique: Direct electron transfer of hemoglobin in octadecylamine layer

The present paper describes the modification of hemoglobin (Hb)-octadecylamine (ODA) Langmuir-Blodgett (LB) film on a gold electrode surface to develop a novel electrochemical biosensor for the detection of hydrogen peroxide. Atomic force microscopy (AFM) image of Hb-ODA LB film indicated Hb molecules existed in ODA layer in a well-ordered and compact form. The immobilized Hb displayed a couple of stable and well-defined redox peaks with an electron transfer rate constant of 4.58 ± 0.95 s⁻¹ and a formal potential of −185 mV (versus Ag/AgCl) in phosphate buffer (1.0 mM, pH 5.0) contain 0.1 M KCl at a scan rate of 200 mV s⁻¹, characteristic of Hb heme Fe(III)/Fe(II) redox couple. The formal potential of Hb heme Fe(III)/Fe(II) redox couple in ODA film shifted linearly between pH 5 and 8 with a slope of −23.8 mV pH⁻¹, suggesting that proton took part in electrochemical reaction. The ODA could accelerate the electron transfer between Hb and the electrode. This modified electrode showed an electrochemical activity to the reduction of hydrogen peroxide (H₂O₂) without the aid of any electron mediator.     

A highly sensitive hydrogen peroxide amperometric sensor based on MnO2-modified vertically aligned multiwalled carbon nanotubes

In this report, a highly sensitive amperometric sensor based on MnO₂-modified vertically aligned multiwalled carbon nanotubes (MnO₂/VACNTs) for determination of hydrogen peroxide (H₂O₂) was fabricated by electrodeposition. The morphology of the nanocomposite was characterized by scanning electron microscopy, energy-dispersive X-ray spectrometer and X-ray diffraction. Cyclic voltammetry, chronoamperometry and electrochemical impedance spectroscopy were applied to investigate the electrochemical properties of the MnO₂/VACNTs nanocomposite electrode. The mechanism for the electrochemical reaction of H₂O₂ at the MnO₂/VACNTs nanocomposite electrode was also discussed. In borate buffer (pH 7.8, 0.20 M), the MnO₂/VACNTs nanocomposite electrode exhibits a linear dependence (R = 0.998) on the concentration of H₂O₂ from 1.2 × 10⁻⁶ M to 1.8 × 10⁻³ M, a high sensitivity of 1.08 × 10⁶ μA M⁻¹ cm⁻² and a detection limit of 8.0 × 10⁻⁷ M (signal/noise = 3). Meanwhile, the MnO₂/VACNTs nanocomposite electrode is also highly resistant towards typical inorganic salts and some biomolecules such as acetic acid, citric acid, uric acid and d-(+)-glucose, etc. In addition, the sensor based on the MnO₂/VACNTs nanocomposite electrode was applied for the determination of trace of H₂O₂ in milk with high accuracy, demonstrating its potential for practical application.     

A sensitive amperometric sensor for hydrazine and hydrogen peroxide based on palladium nanoparticles/onion-like mesoporous carbon vesicle

Onion-like mesoporous carbon vesicle (MCV) with multilayer lamellar structure was synthesized by a simply aqueous emulsion co-assembly approach. Palladium (Pd) nanoparticles were deposited on the MCV matrix (Pd/MCV) by chemical reduction of H₂PdCl₄ with NaBH₄ in aqueous media. Pd(X)/MCV (X wt.% indicates the Pd loading amount) nanocomposites with different Pd loading amount were obtained by adjusting the ratio of precursors. The particular structure of the MCV results in efficient mass transport and the onion-like layers of MCV allows for the obtainment of highly dispersed Pd nanoparticles. The introduction of Pd nanoparticles on the MCV matrix facilitates hydrazine oxidation at more negative potential and delivers higher oxidation current in comparison with MCV. A linear range from 2.0 × 10⁻⁸ to 7.1 × 10⁻⁵ M and a low detection limit of 14.9 nM for hydrazine are obtained at Pd(25)/MCV nanocomposite modified glassy carbon (GC) electrode. A nonenzymatic amperometric sensor for hydrogen peroxide based on the Pd(25)/MCV nanocomposite modified GC electrode is also developed. Compared with MCV modified GC electrode, the Pd(25)/MCV nanocomposite modified GC electrode displays enhanced amperometric responses towards hydrogen peroxide and gives a linear range from 1.0 × 10⁻⁷ to 6.1 × 10⁻³ M. The Pd(25)/MCV nanocomposite modified GC electrode achieves 95% of the steady-current for hydrogen peroxide within 1 s. The combination of the unique properties of Pd nanoparticles and the porous mesostructure of MCV matrix guarantees the improved analytical performance for hydrazine and hydrogen peroxide.     

Flow-injection determination of hydrogen peroxide based on fluorescence quenching of chromotropic acid catalyzed with Fe(II)

Flow-injection analysis system (FIA system), which was based on Fe(II)-catalyzed oxidation of chromotropic acid with hydrogen peroxide, was developed for the determination of hydrogen peroxide. The chromotropic acid has a fluorescence measured at λ_em = 440 nm (emission wavelength) with λ_ex = 235 nm (excitation wavelength), and the fluorescence intensity at λ_em = 440 nm quietly decreased in the presence of hydrogen peroxide and Fe(II), which was caused by Fe(II)-catalyzed oxidation of chromotropic acid with hydrogen peroxide. By measuring the difference of fluorescence intensity, hydrogen peroxide (1.0 × 10⁻⁸-1.0 × 10⁻³ mol L⁻¹) could be determined by the proposed FIA system, whose analytical throughput was 40 samples h⁻¹. The relative standard deviation (RSD) was 1.03% (n = 10) for 4.0 × 10⁻⁸ mol L⁻¹ hydrogen peroxide. The proposed FIA technique could be applied to the determination of hydrogen peroxide in rain water samples.     

Rosmarinic acid determination using biomimetic sensor based on purple acid phosphatase mimetic

A new heterodinuclear Fe(III)Zn(II) complex which mimics the active site of the hydrolytic enzyme red kidney bean purple acid phosphatase was synthesized and characterized by IR, CHN and X-ray crystallographic analyses. This complex, [Fe^IIIZn^II(μ-OH)bpbpmp-CH₃](ClO₄)₂, containing the ligand (H₂bpbpmp-CH₃ = {2-[bis(2-pyridylmethyl)aminomethyl]-6-[(2-hydroxy-5-methylbenzyl) (2-pyridyl-methyl) aminomethyl]-4-methyl-phenol}) was employed in the construction of a biomimetic sensor and used in the determination of rosmarinic acid in plant extract samples. The response parameters and optimization of the biomimetic sensor design were evaluated. The best performance of this sensor was obtained for 75:15:10% (w/w/w) of the graphite powder:nujol:Fe(III)Zn(II) complex, 0.1 mol L⁻¹ phosphate buffer solution (pH 7.5), 1.19 × 10⁻⁴ mol L⁻¹ hydrogen peroxide with frequency, pulse amplitude, and scan increment at 30 Hz, 100 mV, and 0.6 mV, respectively. The rosmarinic acid concentration was linear in the range of 2.98 × 10⁻⁵ to 3.83 × 10⁻⁴ mol L⁻¹ (r = 0.9991) with a detection limit of 2.30 × 10⁻⁶ mol L⁻¹. This biomimetic sensor demonstrated long-term stability (300 days; 900 determinations) and reproducibility, with a relative standard deviation of 12.0%. The recovery study of rosmarinic acid in plant extract samples gave values from 90.3 to 98.3% and the concentrations determined showed agreement when compared with those obtained using capillary electrophoresis at the 95% confidence level.     

A novel bimediator amperometric sensor for electrocatalytic oxidation of gallic acid and reduction of hydrogen peroxide

A novel bimediator amperometric sensor is fabricated for the first time by surface modification of graphite electrode with thionine (TH) and nickel hexacyanoferrate (NiHCF). The electrochemical behavior of the TH/NiHCF bimediator modified electrode was characterized by cyclic voltammetry, differential pulse voltammetry and chronoamperometry. The TH/NiHCF bimediator modified electrode exhibited a pair of distinct redox peaks for NiHCF and TH with formal potentials of 0.33 V and −0.27 V vs. SCE at a scan rate of 50 mV s⁻¹ in 0.1 M NaNO₃ and 0.1 M NH₄NO₃ respectively. The electrocatalytic activity of the bimediator modified electrode towards oxidation of gallic acid with NiHCF and reduction of hydrogen peroxide with TH was evaluated and it was observed that the modified electrode showed an electrocatalytic activity towards the oxidation of gallic acid in the concentration range of 4.99 × 10⁻⁶–1.20 × 10⁻³ M with a detection limit of 1.66 × 10⁻⁶ M (S/N = 3) and reduction of H₂O₂ in the concentration range of 1.67 × 10⁻⁶–1.11 × 10⁻³ M with a detection limit of 5.57 × 10⁻⁷ M (S/N = 3). The bimediator modified electrode was found to exhibit good stability and reproducibility.     

Electrochemical characteristics of a platinum electrode modified with a matrix of polyvinyl butyral and colloidal Ag containing immobilized horseradish peroxidase

A new hydrogen peroxide biosensor was constructed, which consisted of a platinum electrode modified by a matrix of polyvinyl butyral (PVB) and nanometer-sized Ag colloid containing immobilized horseradish peroxidase (HRP), and using Co(bpy)₃³⁺ as mediator in the hydrogen peroxide solution. The electrochemical characteristics of the biosensor were studied by cyclic voltammetry and chronoamperometry. The modified process was characterized by electrochemical impedance spectroscopy and cyclic voltammetry. The HRP immobilized on colloidal Ag was stable and retained its biological activity. The sensor displays excellent electrocatalytic response to the reduction of H₂O₂. Analytical parameters such as pH and temperature were also studied. Linear calibration for H₂O₂ was obtained in the range of 1×10^–5 to 1×10^–2 M under optimized conditions. The sensor was highly sensitive to H₂O₂, with a detection limit of 2×10^–6 M, and the sensor achieved 95% of steady-state current within 10 s. The sensor exhibited high sensitivity, selectivity and stability.     

Characterization of gold-thiol-8-hydroxyquinoline self-assembled monolayers for selective recognition of aluminum ion using voltammetry and electrochemical impedance spectroscopy

Gold electrode surface is modified via covalent attachment of a synthesized thiol functionalized with 8-hydroxyquinoline, p-((8-hydroxyquinoline)azo) benzenethiol (SHQ), for the first time. The behavior of the nanostructured electrode surface (Au–SHQ) is characterized by electrochemical techniques including cyclic and differential pulse voltammetry (CV and DPV), and electrochemical impedance spectroscopy (EIS). The modified surface is stable in a wide range of potentials and pHs. A surface pK_a of 6.0 ± 0.1 is obtained for Au–SHQ electrode using surface acid/base titration curves constructed by CV and EIS measurements as a function of pH. These results helped to determine the charge state of the surface as a function of pH. The gold modified electrode surface showed good affinity for sensing the Al(III) ion at pH 5.5. The sensing process is based on (i) accumulation and complex formation between Al(III) from the solution phase and 8HQ function on the Au electrode surface (recognition step) and (ii) monitoring the impedance of the Au–SHQ–Al(III) complex against redox reaction rate of parabenzoquinone (PBQ) (signal transduction step). The PBQ is found to be a more suitable probe for this purpose, after testing several others. Thus, the sensor was tested for quantitative determination of Al(III) from the solution phase. At the optimized conditions, a linear response, from 1.0 × 10⁻¹¹ to 1.2 × 10⁻⁵ M Al(III) in semi-logarithmic scale, with a detection limit of 8.32 × 10⁻¹² M and mean relative standard deviation of 3.2% for n = 3 at 1.0 × 10⁻⁷ M Al(III) is obtained. Possible interferences from coexisting cations and anions are also studied. The results show that many ions do not interfere significantly with the sensor response for Al(III). Validity of the method and applicability of the sensor are successfully tested by determination of Al(III) in human blood serum samples.     

Electrochemical bisphenol A sensor based on N-doped graphene sheets

Bisphenol A (BPA), which could disrupt endocrine system and cause cancer, has been considered as an endocrine disruptor. Therefore, it is very important and necessary to develop a sensitive and selective method for detection of BPA. Herein, nitrogen-doped graphene sheets (N-GS) and chitosan (CS) were used to prepare electrochemical BPA sensor. Compared with graphene, N-GS has favorable electron transfer ability and electrocatalytic property, which could enhance the response signal towards BPA. CS also exhibits excellent film forming ability and improves the electrochemical behavior of N-GS modified electrode. The sensor exhibits a sensitive response to BPA in the range of 1.0 × 10⁻⁸–1.3 × 10⁻⁶ mol L⁻¹ with a low detection limit of 5.0 × 10⁻⁹ mol L⁻¹ under the optimal conditions. Finally, this proposed sensor was successfully employed to determine BPA in water samples with satisfactory results.     

Electrocatalytic assay of mercury(II) ions using a bifunctional oligonucleotide signal probe

Engineered nucleic acid probes containing recognition and signaling functions find growing interest in biosensor design. In this paper, we developed a novel electrochemical biosensor for sensitive and selective detecting of Hg²⁺ based on a bifunctional oligonucleotide signal probe combining a mercury-specific sequence and a G-quadruplex (G4) sequence. For constructing the electrochemical Hg²⁺ biosensor, a thiolated, mercury-specific oligonucleotide capture probe was first immobilized on gold electrode surface. In the presence of Hg²⁺, a bifunctional oligonucleotide signal probe was hybridized with the immobilized capture probe through thymine–mercury(II)–thymine interaction-mediated surface hybridization. The further interaction between G4 sequence of the signal probe and hemin generated a G4–hemin complex, which catalyzed the electrochemical reduction of hydrogen peroxide, producing amplified readout signals for Hg²⁺ interaction events. This electrochemical Hg²⁺ biosensor was highly sensitive and selective to Hg²⁺ in the concentration of 1.0 nM to 1 μM with a detection limit of 0.5 nM. The new design of bifunctional oligonucleotide signal probes also provides a potential alternative for developing simple and effective electrochemical biosensors capable of detecting other metal ions specific to natural or artificial bases.     

Amperometric detection of nitrite based on Dawson-type vanodotungstophosphate and carbon nanotubes

A nitrite sensor based on Dawson vanodotungstophosphates α₂-K₇P₂VW₁₇O₆₂·18H₂O (P₂W₁₇V) and carbon nanotubes (CNTs) was prepared by electrostatic layer-by-layer self-assembly technique. The sensor {PEI/PSS/[PDDA/P₂W₁₇V-CNTs]_n} was characterized by UV–vis spectroscopy, atomic force microscopy (AFM), scanning electron microscopy (SEM) and X-ray photoelectron spectra (XPS). The electron transfer and sensing ability of this sensor were explored using cyclic voltammetry (CV) and electrochemical impedance spectra (EIS) technology. The results show that the incorporation of CNTs and P₂W₁₇V into the composite film endowed the modified electrode with fast transfer rate and high electrocatalytic activity towards oxidation of nitrite. This nitrite sensor with 10 bilayers has a broad linear range of 5 × 10⁻⁸ to 2.13 × 10⁻³ M, a low detection limit of 0.0367 μM (S N⁻¹ = 3), a high sensitivity of 0.35 mA mM⁻¹ NO₂⁻, an excellent anti-interference property in the presence of other potential interfering species and a good stable. It was successfully employed for determination of nitrite in real towards.     

A novel nonenzymatic hydrogen peroxide sensor based on multi-wall carbon nanotube/silver nanoparticle nanohybrids modified gold electrode

A novel strategy to fabricate hydrogen peroxide (H₂O₂) sensor was developed based on multi-wall carbon nanotube/silver nanoparticle nanohybrids (MWCNT/Ag nanohybrids) modified gold electrode. The process to synthesize MWCNT/Ag nanohybrids was facile and efficient. In the presence of carboxyl groups functionalized multi-wall carbon nanotubes (MWCNTs), silver nanoparticles (Ag NPs) were in situ generated from AgNO₃ aqueous solution and readily attached to the MWCNTs convex surfaces at room temperature, without any additional reducing reagent or irradiation treatment. The formation of MWCNT/Ag nanohybrids product was observed by transmission electron microscope (TEM), and the electrochemical properties of MWCNT/Ag nanohybrids modified gold electrode were characterized by electrochemical measurements. The results showed that this sensor had a favorable catalytic ability for the reduction of H₂O₂. The resulted sensor could detect H₂O₂ in a linear range of 0.05-17 mM with a detection limit of 5 × 10⁻⁷ M at a signal-to-noise ratio of 3. The sensitivity was calculated as 1.42 μA/mM at a potential of −0.2 V. Additionally, it exhibited good reproducibility, long-term stability and negligible interference of ascorbic acid (AA), uric acid (UA), and acetaminophen (AP).