Microflow injection chemiluminescence system with spiral microchannel for the determination of cisplatin in human serum

A new microflow injection chemiluminescence (μFI-CL) system was described for the determination of cisplatin in human serum. By using the microchip with double spiral channel configuration, the sensitivity was greatly enhanced due to more efficient mixing of the analyte and reagent solutions. Experimental results revealed that common ions in human serum, such as Mn²⁺, Co²⁺, Fe³⁺, Cu²⁺, Zn²⁺, Ni²⁺, Na⁺, K⁺, Ca²⁺, Cl⁻, NO₃⁻, Ac⁻, CO₃²⁻, PO₄³⁻, SO₄²⁻ did not cause interference with the detection of Pt(II) by using 1,10-phenanthroline as the masking agent. Under the optimized conditions, a linear calibration curve (R² = 0.998) over the range 2.0 × 10⁻⁸ to 2.0 × 10⁻⁶ mol L⁻¹ was obtained with the detection limit of 1.24 × 10⁻⁹ mol L⁻¹. The relative standard deviation was found to be 3.46% (n = 12) for 2.0 × 10⁻⁷ mol L⁻¹. The sample consumption was only 2 μL with the sample throughput of 72 h⁻¹. It had been used for trace platinum determination in cisplatin injection and human serum samples after the dosage of cisplatin. The recovery varied from 97.6 to 103.9%. The results proved that the proposed μFI-CL system had the advantages of high sensitivity and precision, low sample and reagents consumption, and high analytical throughput.     

An acyclic,dansyl based colorimetric and fluorescent chemosensor for Hg(II) via twisted intramolecular charge transfer (TICT)

An efficient fluorescent chemosensor for Hg²⁺ ion, based on 5-(dimethylamino)-N-(2-mercaptophenyl)naphthalene-1-sulfonamide, has been developed. It exhibits Hg²⁺-selective on–off fluorescence quenching behavior via twisted intramolecular charge transfer (TICT) mechanism, which is rationalized by time dependent density functional theory (TD-DFT) calculations. The system exhibits visible color change from colorless to gray upon Hg²⁺ binding with very high selectivity and sensitivity (as low as 5.0 × 10⁻¹⁰ mol L⁻¹) over other metal ions such as K⁺, Na⁺, Ag⁺, Mn²⁺, Ca²⁺, Ba²⁺, Fe²⁺, Zn²⁺, Pb²⁺, Cu²⁺, Sn²⁺, Cd²⁺, Ni²⁺ and Co²⁺. The present sensing system is also successfully applied for the detection of Hg²⁺ ion in real samples.     

A new fluorescent sensor bearing three dansyl fluorophores for highly sensitive and selective detection of mercury(II) ions

A novel fluorometric sensor bearing three dansyl moieties based on tris[2-(2-aminoethylthio)ethyl]amine was prepared by a simple approach using a conventional two-step synthesis. The sensor exhibits highly Hg²⁺-selective ON-OFF fluorescence quenching behavior in aqueous acetonitrile solutions and is shown to discriminate various competing metal ions, particularly Cu²⁺, Ag⁺, and Pb²⁺ as well as Ca²⁺, Cd²⁺, Co²⁺, Fe³⁺, Mn²⁺, Na⁺, Ni²⁺, and Zn²⁺, with a detection limit of 1.15 × 10⁻⁷ M or 23 ppb.     

Novel potentiometric copper (II) selective membrane sensors based on cyclic tetrapeptide derivatives as neutral ionophores

Two novel membrane sensors sensitive and reasonably selective for Cu²⁺ ions are described. These are based on the use of newly synthesized cyclic tetrapeptide derivatives as neutral ionophores and sodium tetraphenylborate (NaTPB) as an anionic excluder in plasticized PVC membranes. The sensors exhibit fast and stable near-Nernstian response over the concentration range 1.0 × 10⁻⁶ mol l⁻¹ to 1.0 × 10⁻² mol l⁻¹ Cu²⁺ with a cationic slope of 30.2-25.9 mV per decade at pH 4.5-7 with a lower detection limit of 0.05-0.13 μg ml⁻¹. Effects of plasticizers, lipophilic salts and various foreign common ions are tested. The sensors display long life-span, long term stability, high reproducibility, and short response time. Selectivity of both sensors is significantly high for Cu²⁺ over Fe³⁺, Al³⁺, Zn²⁺, Cd²⁺, Hg²⁺, Ni²⁺, Co²⁺, Mn²⁺, alkaline earth and alkali metal ions. The sensors are used for direct measurement of copper content in different rocks and industrial wastewater samples from electroplating factories. The results agree fairly well with data obtained using atomic absorption spectrometry.     

Fluorescent oligomer as a chemosensor for the label-free detection of Fe and dopamine with selectivity and sensitivity

In this article, a sensitive and selective turn-off fluorescence chemosensor, Tyloxapol (one kind of water soluble oligomer), was developed for the label-free detection of Fe³⁺ ions in aqueous solution. Fluorescence (FL) experiments demonstrated that Tyloxapol was a sensitive and selective fluorescence sensor for the detection of Fe³⁺ directly in water over a wide range of metal cations including Na⁺, K⁺, Ag⁺, Hg²⁺, Cd²⁺, Co²⁺, Cu²⁺, Cr³⁺, Mn²⁺, Ba²⁺, Zn²⁺, Ni²⁺, Mg²⁺, Ca²⁺, and Pb²⁺. Moreover, the fluorescence intensity of Tyloxapol has shown a linear response to Fe³⁺ in the concentration range of 0–100 μmol L⁻¹ with a detection limit of 2.2 μmol L⁻¹ in aqueous solution. Next, based on a competition mechanism, another turn-on sensing application of the Tyloxapol/Fe³⁺ platform to probe dopamine (DA) against various other biological molecules such as other neurotransmitters or amino acids (norepinephrine bitartrate, acetylcholine chloride, alanine, valine, phenylalanine, tyrosine, leucine, glycine, histidine) were also investigated. It is expected that our strategy may offer a new approach for developing simple, cost-effective, rapid and sensitive sensors in biological and environmental applications.     

Electrically induced fluorescence Fe sensing behavior of nanostructured Tiron doped polypyrrole

Nanostructured polypyrrole (PPy) film doped with Tiron was electrodeposited from aqueous solution on the surface of transparent electrode and used for sensitive, selective and rapid electrically controlled fluorescence detection of Fe³⁺ in aqueous media. The fluorescence intensity of PPy-Tiron film decreases linearly in the presence of Fe³⁺ by applying negative potential over a concentration range from 5.0 × 10⁻⁸ to 1.0 × 10⁻⁶ mol L⁻¹, with a relatively fast response time of less than 30 s at pH 7.4. The detection is not affected by the coexistence of other competitive metal ions such as Al³⁺, Ce³⁺, Tl³⁺, La³⁺, Bi³⁺, Cr²⁺, Mn²⁺, Fe²⁺, Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Cd²⁺, Hg²⁺, Pb²⁺, Na⁺, K⁺, Mg²⁺, Ca²⁺, Sr²⁺ and Ba²⁺. The proposed electro-fluorescence sensor has a potential application to the determination of Fe³⁺ in environmental and biological systems. The fluorescent thin film sensor was also used as a novel probe for Fe³⁺/Fe²⁺ speciation in aqueous solution.     

Naked-eye colorimetric analysis of Hg2+ with bi-color CdTe quantum dots multilayer films

A novel direct quantificational method through naked-eye colorimetric analysis of Hg²⁺ was constructed based on different degree of the fluorescence quenching of bi-color quantum dots (QDs) multilayer films (2-QDMF). The functional multilayer films were assembled by layer-by-layer (LBL) deposition of oppositely charged CdTe QDs and poly(dimethyldiallylemmonium chloride) (PDDA). Then the outermost layer of 2-QDMF was cross-linked to bovine serum albumin (BSA), polyethylene glycol (PEG) or glutathione (GSH). It was found that when BSA modified quartz slides were immersed into solutions containing Hg²⁺ and Cu²⁺ respectively, the 2-QDMF can be quenched by Hg²⁺, but not by Cu²⁺. Under the optimization conditions, the quenched photoluminescence (PL) intensities of multilayer films were almost linearly proportional to the concentration of Hg²⁺ in the range of 1.0 × 10⁻⁸ to 1.0 × 10⁻⁶ mol L⁻¹ and the detection limit was 4.5 × 10⁻⁹ mol L⁻¹. The proposed method is intuitional and convenient, which can be applied to the determination of trace Hg²⁺ in the artificial water sample with satisfactory results.     

On-line metals preconcentration and simultaneous determination using cloud point extraction and inductively coupled plasma optical emission spectrometry in water samples

A new on-line cloud point extraction (CPE) system coupled to ICP-OES was designed for simultaneous extraction, preconcentration and determination of Cd²⁺, Co²⁺, Cr³⁺, Cu²⁺, Fe³⁺ and Mn²⁺ ions in water samples. This is based on the complexation of the metal ions with 1-(2-thenoyl)-3,3,3-trifluoraceton reagent (TTA) at pH 6.0 in the presence of non-ionic surfactant of Triton X-114. The micellar solution was heated above 60 °C and loaded through a column packed with cotton, which acts as a filter for retaining the analyte-entrapped surfactant-rich phase. Then the surfactant-rich phase was eluted using propanol:0.5 mol L⁻¹ nitric acid solution (75:25, v/v) at a flow rate of 3.0 mL min⁻¹ and directly introduced into the nebulizer of the ICP-OES. Several factors influencing the instrumental conditions and extraction were evaluated and optimized. Under the optimum conditions, the enhancement factors of the proposed method for target ions were between 42 and 97, the detection limits (DLs) were in the range of 0.1-2.2 μg L⁻¹. The relative standard deviations (R.S.D.s) at 100 μg L⁻¹ concentration levels of each ion were found to be less than 4.6%. Also, the calibration graphs were linear in the range of 0.5-100 μg L⁻¹ with the correlation coefficients within the range of 0.9948-0.9994.Finally, the developed method was successfully applied to the extraction and determination of the mentioned metal ions in the tap, well, sea and mineral water samples and satisfactory results were obtained.     

Complexation of metal ions with the novel azathia crown ethers carrying anthracene pendant in acetonitrile–dichloromethane

A series of crown ethers carrying an anthracene group with nitrogen–sulfur donor atom, which differ in having three, four and five sulfur atoms in the macrocycle was designed and synthesized by the reaction of the corresponding macrocyclic compound and 9-chloromethyl-anthracene. The influence of metal cations such as Al³⁺, Zn²⁺, Fe²⁺, Fe³⁺, Co²⁺, Ni²⁺, Mn²⁺, Cu²⁺, Cd²⁺, Hg²⁺ and Pb²⁺ on the spectroscopic properties of the ligands was investigated in acetonitrile–dichloromethane (1:1) by means of absorption and emission spectrometry. Absorption spectra show isosbestic points in the spectrophotometric titration of Al³⁺, Zn²⁺, Fe²⁺, Fe³⁺, Cu²⁺, Hg²⁺ and Pb²⁺ the results of which disclosed the complexation compositions and complex stability constants of the novel ligands with these cations. The monoazapentathia crown ether showed sensitivity for Al³⁺ with linear range and detection limit of 2.6 × 10⁻⁶ M–2.6 × 10⁻⁵ M and 8.1 × 10⁻⁷ M, respectively.     

Simultaneous determination of Mn(II), Cu(II) and Fe(III) as 2-(5′-bromo-2′-pyridylazo)-5-diethylaminophenol complexes by adsorptive cathodic stripping voltammetry at a carbon paste electrode

A simple and precise square-wave adsorptive cathodic stripping voltammetry (SW-AdCSV) method has been described for simultaneous determination of Mn(II), Cu(II) and Fe(III) in water samples using a carbon paste electrode. In 0.1 mol L⁻¹ acetate buffer (pH 5) containing 50 μmol L⁻¹ of 2-(5′-bromo-2′-pyridylazo)-5-diethylaminophenol (5-Br-PADAP), Mn(II), Cu(II) and Fe(III) were simultaneously determined as metal-complexes with 5-Br-PADAP following preconcentration onto the carbon paste electrode by adsorptive accumulation at +1.0 V (vs. Ag/AgCl/3 M KCl). Insignificant interference from various cations (K⁺, Na⁺, Mg²⁺, Ca²⁺, Al³⁺, Bi³⁺, Sb³⁺, Se⁴⁺, Zn²⁺, Ni²⁺, Co²⁺, Cd²⁺, Pb²⁺, V⁵⁺, Ti⁴⁺ and NH₄⁺), anions (HCO₃⁻, Cl⁻, NO³⁻, SO₄²⁻ and PO₄³⁻) and ascorbic acid was noticed. Limits of detection of 0.066, 0.108 and 0.093 μg L⁻¹ and limits of quantitation of 0.22, 0.36 and 0.31 μg L⁻¹ Mn(II), Cu(II) and Fe(III), respectively, were achieved by the described method. The described stripping voltammetry method was successfully applied for simultaneous determination of Mn(II), Cu(II) and Fe(III) in ground, tap and bottled natural water samples.     

Ultra-sensitive determination of cyanide in surface water by gas chromatography–tandem mass spectrometry after derivatization with 2-(dimethylamino)ethanethiol

A gas chromatography–tandem mass spectrometric (GC–MS/MS) method has been established for the determination of cyanide in surface water. This method is based on the derivatization of cyanide with 2-(dimethylamino)ethanethiol in surface water. The following optimum reaction conditions were established: reagent dosage, 0.7 g L⁻¹ of 2-(dimethylamino)ethanethiol; pH 6; reaction carried out for 20 min at 60 °C. The organic derivative was extracted with 3 mL of ethyl acetate, and then measured by using GC–MS/MS. Under the established conditions, the detection and quantification limits were 0.02 μg L⁻¹ and 0.07 μg L⁻¹ in 10-mL of surface water, respectively. The calibration curve had a linear relationship relationship with y = 0.7140x + 0.1997 and r² = 0.9963 (for a working range of 0.07–10 μg L⁻¹) and the accuracy was in a range of 98–102%; the precision of the assay was less than 7% in surface water. The common ions Cl⁻, F⁻, Br⁻, NO₃⁻, SO₄²⁻, PO₄³⁻, K⁺, Na⁺, NH₄⁺, Ca²⁺, Mg²⁺, Ba²⁺, Mn⁴⁺, Mn²⁺, Fe³⁺, Fe²⁺ and sea water did not interfere in cyanide detection, even when present in 1000-fold excess over the species. Cyanide was detected in a concentration range of 0.07–0.11 μg L⁻¹ in 6 of 10 surface water samples.     

A cationic porphyrin-based self-assembled film for mercury ion detection

A cationic 5,15-(p-(9,9-bis(6-trimethylammoniumhexyl)fluorenylethynyl)phenyl)porphyrin tetrabromide was synthesized and the self-assembled films were used for Hg²⁺ detection in aqueous media. The detection response is based on fluorescence quenching of the porphyrin molecule upon coordination with Hg²⁺. The detection shows high selectivity for Hg²⁺ over Cu²⁺, Zn²⁺, Pb²⁺, Cd²⁺, Mn²⁺, Ni²⁺, Co²⁺ and Ca²⁺. A linear response toward Hg²⁺ in a concentration range of 1 × 10⁻¹⁰-1 × 10⁻⁶ M was observed for the film with a detection limit of 0.1 nM. The cationic porphyrin film shows higher stability and significant improvement in detection sensitivity, as compared to other porphyrin-based sensors. The amphiphilic cationic nature of the porphyrin synthesized also allows for the direct deposition of a porphyrin layer on a bare glass surface through self-assembly.     

Sensitive and robotic determination of bromate in sea water and drinking deep-sea water by headspace solid-phase micro extraction and gas chromatography–mass spectrometry

A robotic method has been established for the determination of bromate in sea water and drinking deep-sea water. Bromate in water was converted into volatile derivative, which was measured with headspace solid-phase micro extraction and gas chromatography–mass spectrometry (HS-SPME GC–MS). Derivatization reagent and the HS-SPME parameters (selection of fibre, extraction/derivatization temperature, heating time and; the morality of HCl) were optimized and selected. Under the established conditions, the detection and the quantification limits were 0.016 μg L⁻¹ and 0.051 μg L⁻¹, respectively, and the intra- and inter-day relative standard deviation was less than 7% at concentrations of 1.0 and 10.0 μg L⁻¹. The calibration curve showed good linearity with r² = 0.9998. The common ions Cl⁻, NO₃⁻, SO₄²⁻, HPO₄²⁻, H₂PO₄⁻, K⁺, Na⁺, NH₄⁺, Ca²⁺, Mg²⁺, Ba²⁺, Mn⁴⁺, Mn²⁺, Fe³⁺ and Fe²⁺ did not interfere even when present in 1000-fold excess over the active species. The method was successfully applied to the determination of bromate in sea water and drinking deep-sea water.     

Selective detection of phosphaphenanthrenecontaining luminophors with aggregation-induced emission enhancement to transition metal ions

Transition metal ions (Pb²⁺, Zn²⁺, Cd²⁺, Co²⁺, Mn²⁺, Cu²⁺, Ni²⁺, Hg²⁺, Ag⁺, Fe³⁺) in water are used to quench emission of 2-(6-oxido-6H-dibenz 〈c,e〉 〈1,2〉 oxaphosphorin-6-yl)-1,4-phenylene-bis(p-pentyloxylbenzoate)s (MD5) with aggregation-induced emission enhancement (AIEE) in water-acetonitrile (AN) mixture (80:20 by volume). Among all metal ions, Fe³⁺ exhibits the highest quenching efficiency on AIEE of MD5 even when the concentration of Fe³⁺ is lower than 1×10⁻⁶ mol/L. The quenching efficiency of Hg²⁺ is lower than that of Fe³⁺ at the same concentration, though MD5 is used to detect Hg²⁺ efficiently, too. To other metal ions, low quenching efficiency has few relations with a wider concentration range. The UV absorbance spectra show only red shift of absorbance wavelength in the presence of Hg²⁺ and Fe³⁺, which indicates a salt-induced Jaggregation. SEM photos reveal larger aggregation and morphological change of nanoparticles of MD5 in water containing Hg²⁺ and Fe³⁺, which reduce the surface area of MD5 emission for further aggregation. The selective quenching effect of transition metal ions to emission of MD5 has a potential application in chemical sensors of some metal ions.     

A new resonance scattering spectral method for the determination of trace amounts of iodate with rhodamine 6G

Under the conditions of 0.04 mol L⁻¹ HCl-8.0 × 10⁻⁴ mol L⁻¹ KI, there is a fluorescence peak at 540 nm and a synchronous fluorescence peak at 540 nm for rhodamine 6G (RhG). When there is IO₃⁻, it reacts with exceed I⁻ to form I₃⁻. And I₃⁻ and RhG combine into ion association particles. The particles exhibit three resonance scattering peaks at 320, 400 and 595 nm. And there is fluorescence quenching at 540 nm. Iodine concentration is proportional to the intensity of the resonance scattering intensity at 400 nm in the range of 1.0-20 × 10⁻⁷ mol L⁻¹. And a new resonance scattering spectral (RSS) method has been described for the determination of IO₃⁻ in salt samples. The spectral results have been verified that the formation of (RhG-I₃)_n association particles and solid-liquid interfaces are the main factor that cause the fluorescence quenching and resonance scattering effects.     

Fabrication and characterization of hexahistidine-tagged protein functionalized multi-walled carbon nanotubes for selective solid-phase extraction of Cu and Ni

Hexahistidine-tagged protein functionalized multi-walled carbon nanotubes (MWCNTs/6His-tagged protein) were prepared and characterized by ultraviolet-visible spectrophotometry and atomic force microscopy. Both static and dynamical adsorption experiments showed that the MWCNTs/6His-tagged protein served as good sorbent for the solid-phase extraction of Cu²⁺ and Ni²⁺. Effective on-line sorption of Cu²⁺ and Ni²⁺ on the MWCNTs/6His-tagged protein packed microcolumn was achieved in a pH range of 3.0-4.5 and 4.5-6.0, respectively. The retained Cu²⁺ and Ni²⁺ were efficiently eluted with 0.2 mol L⁻¹ imidazole-HCl solution for on-line flame atomic absorption spectrometric determination. The MWCNTs/6His-tagged protein exhibited fairly fast kinetics for the sorption of Cu²⁺ and Ni²⁺, and offered up to 20,000 and 1800 times improvement in the tolerable concentrations of co-existing ions over the MWCNTs for solid-phase extraction of Cu²⁺ and Ni²⁺, respectively. On-line solid-phase extraction at a flow rate of 5.0 mL min⁻¹ for 60 s gave an enhancement factor of 29 for Cu²⁺ and 28 for Ni²⁺, a sample throughput of 45 h⁻¹, and a detection limit (3s) of 0.31 μg L⁻¹ for Cu²⁺ and 0.63 μg L⁻¹ for Ni²⁺. The precision for 11 replicate measurements was 2.4% for 10 μg L⁻¹ Cu²⁺, and 2.5% for 15 μg L⁻¹ Ni²⁺.     

Multiplex sensor for detection of different metal ions based on on–off of fluorescent gold nanoclusters

In this study, a multiplex fluorescence sensor for successive detection of Fe³⁺, Cu²⁺ and Hg²⁺ ions based on “on–off” of fluorescence of a single type of gold nanoclusters (Au NCs) is described. Any of the Fe³⁺, Cu²⁺ and Hg²⁺ ions can cause quenching fluorescence of Au NCs, which established a sensitive sensor for detection of these ions respectively. With the introduction of ethylene diamine tetraacetic acid (EDTA) to the system of Au NCs and metal ions, a restoration of fluorescence may be found with the exception of Hg²⁺. A highly selective detection of Hg²⁺ ion is, thus, achieved by masking Fe³⁺ and Cu²⁺. On the other hand, the masking of Fe³⁺ and Cu²⁺ leads to the enhancement of fluorescence of Au NCs, which in turn provides an approach for successive determination of Fe³⁺ and Cu²⁺ based on “on–off” of fluorescence of Au NCs. Moreover, this assay was applied to the successful detection of Fe³⁺, Cu²⁺ and Hg²⁺ in fish, a good linear relationship was found between these metal ions and the degree of quenched fluorescent intensity. The dynamic ranges of Hg²⁺, Fe³⁺ and Cu²⁺ were 1.96 × 10⁻¹⁰–1.01 × 10⁻⁹, 1.28 × 10⁻⁷–1.27 × 10⁻⁶ and 1.2 × 10⁻⁷–1.2 × 10⁻⁶ M with high sensitivity (the limit of detection of Fe³⁺ 2.0 × 10⁻⁸ M, Cu²⁺ 1.9 × 10⁻⁸ M and Hg²⁺ 2 × 10⁻¹⁰ M). These results indicate that the assay is suitable for sensitive detection of these metal ions even under the coexistence, which can not only determine all three kinds of metal ions successively but also of detecting any or several kinds of metal ions.     

Selective and Sensitive Two New Macroacyclic Schiff base Fluorescent Turn-Off Receptors for Fe3+, DFT Calculation and Their Antibacterial Activity

Two new Macroacyclic Schiff base chemosensors (L₁ and L₂) were synthesized by the one pot condensation reaction of 2-[3-(2-formyl phenoxy)propoxy]benzaldehyde and aminophenol in a 1:2 molar ratio and were characterized by IR, NMR spectroscopy. Both Schiff bases displayed high selectivity and sensitivity towards Fe³⁺ over other metal ions in H₂O-DMF solution (Ag⁺,Cu²⁺, Ni²⁺, Zn²⁺, Mg⁺², Mn⁺², Pb⁺², Co⁺², Hg⁺², Cr⁺³, Na⁺, Ba⁺² and Cd²⁺) due to their structure including oxygen donor atoms. The test results showed fluorescence quenching of the fluorophores when Fe³⁺ was bound to the recognition units. From test results, a high selectivity for Fe³⁺ were discovered in this type of sensors, especially, the probe based on 2-aminophenol exhibited more significant quenching in fluorescence intensity compared with 4-aminophenol-based due to its rigidity structure. In addition, the structure of ligands and their antibacterial properties was investigated.     

Highly selective and sensitive paper-based colorimetric sensor using thiosulfate catalytic etching of silver nanoplates for trace determination of copper ions

A novel, highly selective and sensitive paper-based colorimetric sensor for trace determination of copper (Cu²⁺) ions was developed. The measurement is based on the catalytic etching of silver nanoplates (AgNPls) by thiosulfate (S₂O₃²⁻). Upon the addition of Cu²⁺ to the ammonium buffer at pH 11, the absorption peak intensity of AuNPls/S₂O₃²⁻ at 522 nm decreased and the pinkish violet AuNPls became clear in color as visible to the naked eye. This assay provides highly sensitive and selective detection of Cu²⁺ over other metal ions (K⁺, Cr³⁺, Cd²⁺, Zn²⁺, As³⁺, Mn²⁺, Co²⁺, Pb²⁺, Al³⁺, Ni²⁺, Fe³⁺, Mg²⁺, Hg²⁺ and Bi³⁺). A paper-based colorimetric sensor was then developed for the simple and rapid determination of Cu²⁺ using the catalytic etching of AgNPls. Under optimized conditions, the modified AgNPls coated at the test zone of the devices immediately changes in color in the presence of Cu²⁺. The limit of detection (LOD) was found to be 1.0 ng mL⁻¹ by visual detection. For semi-quantitative measurement with image processing, the method detected Cu²⁺ in the range of 0.5–200 ng mL⁻¹(R² = 0.9974) with an LOD of 0.3 ng mL⁻¹. The proposed method was successfully applied to detect Cu²⁺ in the wide range of real samples including water, food, and blood. The results were in good agreement according to a paired t-test with results from inductively coupled plasma-optical emission spectrometry (ICP-OES).