Modification of polypyrrole nanowires array with platinum nanoparticles and glucose oxidase for fabrication of a novel glucose biosensor

A novel glucose biosensor, based on the modification of well-aligned polypyrrole nanowires array (PPyNWA) with Pt nanoparticles (PtNPs) and subsequent surface adsorption of glucose oxidase (GOx), is described. The distinct differences in the electrochemical properties of PPyNWA–GOx, PPyNWA–PtNPs, and PPyNWA–PtNPs–GOx electrodes were revealed by cyclic voltammetry. In particular, the results obtained for PPyNWA–PtNPs–GOx biosensor showed evidence of direct electron transfer due mainly to modification with PtNPs. Optimum fabrication of the PPyNWA–PtNPs–GOx biosensor for both potentiometric and amperometric detection of glucose were achieved with 0.2 M pyrrole, applied current density of 0.1 mA cm⁻², polymerization time of 600 s, cyclic deposition of PtNPs from −200 mV to 200 mV, scan rate of 50 mV s⁻¹, and 20 cycles. A sensitivity of 40.5 mV/decade and a linear range of 10 μM to 1000 μM (R² = 0.9936) were achieved for potentiometric detection, while for amperometric detection a sensitivity of 34.7 μA cm⁻² mM⁻¹ at an applied potential of 700 mV and a linear range of 0.1–9 mM (R² = 0.9977) were achieved. In terms of achievable detection limit, potentiometric detection achieved 5.6 μM of glucose, while amperometric detection achieved 27.7 μM.     

A Raman spectroscopic study of the phosphate mineral pyromorphite Pb5(PO4)3Cl

A series of selected pyromorphite minerals Pb₅(PO₄)₃Cl from different Australian localities has been studied by Raman spectroscopy complemented with selected infrared spectroscopy. The Raman spectrum of unsubstituted pyromorphite shows a single band at around 920 cm⁻¹ but for the natural minerals two bands at 919 and ∼932 cm⁻¹ attributed to the ν₁ (PO₄)³⁻ stretching vibration. The observation of multiple bands is attributed to the non-equivalence of phosphate units in the pyromorphite structure and the reduction in symmetry of the (PO₄)³⁻ units. This symmetry reduction is confirmed by the observation of multiple bands in both the ν₄ bending region (500–595 cm⁻¹) and the ν₂ bending region (350–500 cm⁻¹). The presence of isomorphic substitution of (PO₄)³⁻ by (AsO₄)³⁻ units is identified by the ν₁ symmetric stretching bands at around 824 and 851 cm⁻¹ and the ν₂ bending region around 331 and 354 cm⁻¹. Contrary to expectation Raman bands in the 3320–3700 cm⁻¹ region are observed and assigned to OH stretching bands of OH units resulting from the substitution of chloride anions in the pyromorphite structure. This study brings in to question the actual formula of natural pyromorphite as it is better represented as Pb₅(PO₄,AsO₄)₃(Cl,OH) · xH₂O.     

Triple-resonance autoionization of uranium optimized for diode laser excitation

The photoionization of uranium via three-step excitation has been optimized for isotope selective trace analysis. A search found 13 new J = 6, 7, and 8 odd-parity states in the 36,850–37,200 cm^− 1 region that allow blue–red–red three-photon excitation at wavelengths favorable for commercial diode laser systems. From each of these 13 states, near-threshold autoionization spectra were recorded at a resolution of 3 × 10^− 4 cm^− 1. Some 30 even-parity autoionizing levels with J = 5 to 9 have also been observed and characterized. Comparison of the spectra allows J assignment for the new intermediate levels as well as selection of an optimized path for trace analysis. We show that, for a chosen scheme using a narrow J = 9 autoionizing resonance at 49,972 cm^− 1, all of the excitation steps can be saturated with powers available from single-mode cw diode laser systems when exciting an atomic beam in perpendicular geometry.     

Integration of a highly ordered gold nanowires array with glucose oxidase for ultra-sensitive glucose detection

A highly sensitive amperometric nanobiosensor has been developed by integration of glucose oxidase (GO_x) with a gold nanowires array (AuNWA) by cross-linking with a mixture of glutaraldehyde (GLA) and bovine serum albumin (BSA). An initial investigation of the morphology of the synthesized AuNWA by field emission scanning electron microscopy (FESEM) and field emission transmission electron microscopy (FETEM) revealed that the nanowires array was highly ordered with rough surface, and the electrochemical features of the AuNWA with/without modification were also investigated. The integrated AuNWA–BSA–GLA–GO_x nanobiosensor with Nafion membrane gave a very high sensitivity of 298.2 μA cm⁻² mM⁻¹ for amperometric detection of glucose, while also achieving a low detection limit of 0.1 μM, and a wide linear range of 5–6000 μM. Furthermore, the nanobiosensor exhibited excellent anti-interference ability towards uric acid (UA) and ascorbic acid (AA) with the aid of Nafion membrane, and the results obtained for the analysis of human blood serum indicated that the device is capable of glucose detection in real samples.     

Spectroscopic and structural characterization of Na2[(VO)2(ttha)]·8H2O (ttha = triethylenetetraamine-N,N,N′,N″,N′″,N′″-hexaacetate): Interpreting the results with density functional theory

Na₂[(V^IVO)₂(ttha)]·8 H₂O (ttha = triethylenetetraamine–N,N,N′,N″,N′″,N′″–hexaacetate ion), prepared by treating [VO(H₂O)₅][(VO)₂(ttha)]·4 H₂O with Na₆(ttha), has been characterized by single crystal X-ray diffraction, infrared spectroscopy, UV–Vis absorption spectroscopy, electron spin resonance spectroscopy, and modeled by density functional theory (DFT). The X-ray structure revealed a distorted octahedral geometry around each vanadium center. The electronic absorption spectrum of [(VO)₂(ttha)]²⁻ (aq) features absorptions at ca. 200 nm (ε > 13900 L mol⁻¹ cm⁻¹), 255 nm (ε = 3480 L mol⁻¹ cm⁻¹), 586 nm (ε = 33 L mol⁻¹ cm⁻¹), and 770 nm (ε = 38 L mol⁻¹ cm⁻¹). The time-dependent density functional theory (TDDFT) calculated electronic absorption spectrum was remarkably similar to the actual spectrum, and TDDFT predicts absorption peaks at 297, 330, 458, 656, and 798 nm. TDDFT assigned the peak at 798 nm to be the α spin HOMO → LUMO transition. Hence, the peak at 770 nm in the actual spectrum is most likely the α spin HOMO → LUMO transition. Moreover, the TDDFT calculations revealed that the α spin HOMO and LUMO are partly comprised of d orbitals on both vanadium centers, and the first derivative electron spin resonance spectrum also suggests that the two unpaired electrons in [(VO)₂(ttha)]²⁻ are localized near the vanadium centers.     

Thin Pd–23%Ag/stainless steel composite membranes: Long-term stability,life-time estimation and post-process characterisation

The long-term stability of Pd–23%Ag/stainless steel composite membranes has been examined in H₂/N₂ mixtures as a function of both temperature and feed pressure. During continuous operation, the membrane shows a good stability at 400 °C while the N₂ leakage increases very slowly at a temperature of 450 °C (P_feed = 10 bar). After 100 days of operation (P_feed = 5–20 bar, T = 350–450 °C), the N₂ permeance equals 7.0 × 10⁻⁹ mol m⁻² s⁻¹ Pa⁻¹, which indicates that the H₂/N₂ permselectivity still lies around 500, based on a H₂ permeance equal to 3.0 × 10⁻⁶ mol m⁻² s⁻¹ Pa⁻¹. Despite the generation of small pinholes, a membrane life-time of several (2–3) years (T ≤ 425 °C) is estimated for the experimental conditions employed based on long-term stability tests over 100 days. Post-process characterisation shows a considerable grain growth and micro-strain relaxation in the Pd–23%Ag membrane after the prolonged permeation experiment. Changes in surface area are relatively small. In addition, segregation of Ag to the membrane surfaces is observed. The formation of pinholes is identified as the main source for the increased N₂ leakage during testing at higher temperature.     

Low power cross-flow atmospheric pressure Ar + He plasma jet : Spectroscopic diagnostic and excitation capabilities

A cross-flow atmospheric plasma jet with distilled water or analyte solution nebulization has been investigated. The plasma gas flows perpendicularly to the RF powered electrode (11.21 MHz) and a grounded electrode was added for plasma stabilization. The working parameters of the plasma generator can be controlled in order to maximize either the plasma power (75 W) or the voltage on the RF powered electrode (plasma power, 40 W). The plasma gas, pure argon (0.4 l min⁻¹) or a mixture of argon (0.3–0.4 l min⁻¹) and helium (0–0.2 l min⁻¹), was also used for liquid nebulization. Optical emission of the plasma, collected in the normal viewing mode, was used for plasma diagnostics and for evaluating its excitation capabilities. The influence of helium content in the mixed-gas plasma on the plasma characteristics and on the emission axial profiles of the plasma gas constituents and of the analytes originate from the wet aerosol was studied. The addition of helium to the argon plasma, generally determines decreases in the emission of the plasma gas constituents (with the exception of molecular nitrogen), in the rotational temperature and in the electron number density and increases in the excitation temperatures and in the emission of easily excitable analytes. Based on the determined electron number densities, it was concluded that in the plasma zone which presents interest from analytical point of view the plasma is not very far from the partial thermodynamic equilibrium. In function of the helium content in the plasma gas and of the axial distance from the powered electrode the excitation temperatures are in the range of 2420–3340 K for argon, 2500–5450 K for oxygen and 900–2610 K for ionic calcium and the electron number densities are in the range of 1.2 10¹²–1.25 10¹³ cm⁻³. Some elements with excitation energy lower than 6 eV were excited in the plasma. The plasma excitation capability depends on the working conditions of the plasma generator (maximum power or maximum voltage on the RF powered electrode) and on the helium content in the mixed-gas plasma. The estimated detection limits for the studied elements (Na, Li, K, Ca, Cu, Ag, Cd, Hg and Zn) are in the range of 7 ng ml⁻¹ to 28 μg ml⁻¹.     

Systematic investigation on new SrCo1−yNbyO3−δ ceramic membranes with high oxygen semi-permeability

SrCo_1−yNb_yO_3−δ (y = 0.025–0.4) were synthesized for oxygen separation application. The crystal structure, phase stability, oxygen nonstoichiometry, electrical conductivity, and oxygen permeability of the oxides were systematically investigated. Cubic perovskite, with enhanced phase stability at higher Nb concentration, was obtained at y = 0.025–0.2. However, the further increase in niobium concentration led to the formation of impurity phase. The niobium doping concentration also had a significant effect on electrical conductivity and oxygen permeability of the membranes. SrCo_0.9Nb_0.1O_3−δ exhibited the highest electrical conductivity and oxygen permeability among the others. It reached a permeation flux of ∼2.80 × 10⁻⁶ mol cm⁻² s⁻¹ at 900 °C for a 1.0-mm membrane under an air/helium oxygen gradient. The further investigation demonstrated the oxygen permeation process was mainly rate-limited by the oxygen bulk diffusion process.     

The structure of mimetite,arsenian pyromorphite and hedyphane – A Raman spectroscopic study

The minerals mimetite Pb₅(AsO₄)₃Cl, arsenian pyromorphite Pb₅(PO₄,AsO₄)₃Cl and hedyphane Pb₃Ca₂(AsO₄)₃Cl have been studied by Raman spectroscopy complimented with infrared spectroscopy. Mimetite is characterised by a band at 812–3 cm⁻¹ attributed to the A_g mode. For the arsenian pyromorphite this band is observed at 818 cm⁻¹ and for hedyphane at 819 cm⁻¹. For mimetite and hedyphane bands at 788 and 765 cm⁻¹ are attributed to A_u and E_1u vibrational modes and are both Raman and infrared active. For the arsenian pyromorphite, Raman bands at 917–1014 cm⁻¹ are attributed to phosphate stretching vibrations. Raman spectroscopy clearly identifies bands attributable to isomorphous substitution of arsenate by phosphate. The observation of low intensity bands in the 3200–3550 cm⁻¹ region are assigned to adsorbed water and OH units, thus indicating some replacement of chloride ions with hydroxyl ions.     

Ultra-sensitive quantification of lysozyme based on element chelate labeling and capillary electrophoresis–inductively coupled plasma mass spectrometry

In this study, an ultra-sensitive method for the quantification of lysozyme based on the Gd³⁺ diethylenetriamine-N,N,N′,N″,N″-pentaacetic acid labeling and capillary electrophoresis–inductively coupled plasma mass spectrometry (CE–ICP–MS) was described. The Gd³⁺-tagged lysozyme was effectively separated by capillary electrophoresis (CE) and sensitively determined by inductively coupled plasma mass spectrometry (ICP–MS). Based on the gadolinium-tagging and CE–ICP–MS, the lysozyme was determined within 12 min with an extremely low detection limit of 3.89 attomole (3.89 × 10⁻¹¹ mol L⁻¹ for 100 nL of sample injection) and a RSD < 6% (n = 5). The proposed method has been successfully used to detect lysozyme in saliva samples with a recovery of 91–106%, suggesting that our method is sensitive and reliable. The success of the present method provides a new potential for the biological assays and sensitive detection of low-abundant proteins.     

FTIR and fluorescence studies on the ground and excited state hydrogen-bonding interactions between 1-methylindole and water in water–triethylamine mixtures

The ground and excited state π-hydrogen-bonding interactions between 1-methylindole, MI, and water have been investigated in water–triethylamine, water–TEA, mixtures. FTIR measurements performed on the OH stretching bands of the water–TEA clusters show that, upon MI addition, the typical bands of the water–TEA system at 3348 cm⁻¹, 3440 cm⁻¹, 3545 cm⁻¹ and 3682 cm⁻¹ diminish, whereas two new absorption bands at 3316 cm⁻¹ and 3654 cm⁻¹ grow up. These spectral changes have been rationalised assuming the formation of only one 1:1 water–MI complex, in which the dangling protons in the water–TEA clusters are hydrogen bonded to the π-cloud of the MI aromatic ring. Steady state and time resolved fluorescence measurements provide additional proofs on the ground state formation of a fluorescent OH ? π hydrogen bonded complex. The relevance that the present and the previously reported results could have on the indole ring photophysics is discussed.     

Hexacyanometallate anions as precursors of two new trinuclear heterobimetallic assemblies: Syntheses,structures and cryomagnetic properties

Two new cyano bridged Cu–Co and Cu–Fe trinuclear bimetallic assemblies, [(CuL)[Co(CN)₆](CuL)]ClO₄ · 3.5H₂O (1) and [(CuL)[Fe(CN)₆](CuL)] · 13H₂O (2) where [L = (3E,5E)-N¹,N⁴-bis((pyridin-2-yl)methylene)butane-1,4-diamine] have been prepared using cyanometallates as anion precursors and characterised by elemental analyses, spectroscopic studies, single crystal X-ray diffraction and cryomagnetic susceptibility measurements. Magneto-structural correlations have been drawn from cryomagnetic susceptibility measurements over a wide temperature range (2–300 K) under 0.5 T magnetic fields. Weak antiferromagnetic interactions with J = −0.81 and −0.73 cm⁻¹ are found for 1 and 2, respectively, showing a very weak coupling, as expected from the diamagnetic long chain –NC–Co–CN–CN– and –NC–Fe–CN–CN– bridges revealed from the single crystal X-ray diffraction studies.     

Resonantly laser induced plasmas in gases: The role of energy pooling and exothermic collisions in plasma breakdown and heating

The present work is a systematic experimental study of the plasma formation in cesium vapor induced by a continuous laser tuned to the resonance transition 6S_1/2–6P_3/2. Taking into account the measured absolute population densities of Cs ground and excited state atoms as well as the electron densities derived from Stark broadening of the Cs lines, complete local thermodynamic equilibrium in the laser-produced plasma was found for laser power densities ≈ 10 Wcm^− 2 at cesium ground state number densities of about 10¹⁷ cm^− 3. Direct conversion of the excitation energy or parts of the excitation energy in exothermic collisions of laser-excited atoms is concluded to be the major process for atomic vapor heating and subsequent formation of LTE plasmas.     

Structure and magnetic properties of a copper(II) compound with syn–anti carboxylato- and linear Cu–Cl–Cu chloro-bridges

The copper(II) polymer Cu(2-qic)Cl (2-qic = quinoline-2-carboxylate) was synthesized and then characterized by X-ray crystal structure determination, spectroscopic and magnetic studies. The crystal structure consists of copper(II) ions with two different chromophores: four-coordinated in a square-planar geometry and five-coordinated in an environment between square-pyramidal and trigonal-bipyramidal. The copper ions are bridged sequentially through the carboxylate groups in a syn–anti conformation, forming an infinite one-dimensional zigzag chain with two alternating non-equivalent copper(II) chromophores. The chloride atom acts as a single chloro-bridge link to adjacent chains, forming a ribbon type structure (1D). The variable-temperature (1.8–300 K) magnetic susceptibility data of the complex were interpreted with the dimer law using the molecular field approximation. The results obtained indicate a very weak ferromagnetic (J₂ = 0.37 cm⁻¹) interchain interaction through the syn–anti carboxylate bridge. A relatively strong antiferromagnetic interaction, transmitted through the chloro-bridge with an exchange coupling of J₁ = −57.0 cm⁻¹, dominates the magnetic properties of this complex. The magnitude and the nature of the exchange coupling are explained on the basis of the structural results.     

Investigation of Ba fully occupied A-site BaCo0.7Fe0.3−xNbxO3−δ perovskite stabilized by low concentration of Nb for oxygen permeation membrane

BaCo_0.7Fe_0.3−xNb_xO_3−δ (BCFN, x = 0–0.2) were prepared by the conventional solid state reaction process. The crystal structure, electrical conductivity and oxygen desorption property were studied by X-ray diffraction (XRD), different thermal analysis (DTA), four-terminal direct current conductivity and oxygen temperature programmed desorption (O₂-TPD), respectively. At x = 0.08–0.20, BCFN have a cubic perovskite structure, while it exhibits the hexagonal structure for x = 0.00 and the mixed phases of cubic perovskite with trace amount of hexagonal for x = 0.05. BCFN shows good structure stability in 5%H₂ + Ar reducing atmosphere, and it is enhanced with the increased Nb-doping content. The electrical conductivity of BCFN increases with increasing temperature and decreases with the Nb substitution content for iron. BCFN exhibits a p-type semiconductor and obeys the thermally activated small polarons hopping mechanism. The oxygen fluxes increase with the working temperature and the COG flow rate, but decrease with increasing Nb content. The flux of BCFN (x = 0.08) with 1.0 mm thickness membrane reaches 25.77 ml min⁻¹ cm⁻² at 875 °C, higher than most of the reported materials.     

Synthesis,characterization, and properties of novel bis(aryl)carbazole-containing N-coumarin derivatives

A series of novel N-coumarin derivatives containing oligothiophene-substituted N-coumarins as the core and bis(aryl)carbazoles as the substituent were synthesized and characterized. Their optical, electrochemical, and thermal properties were investigated. The electroluminescence (EL) properties of the selected materials were also studied. Solution-processed OLEDs with green and yellow light emission, turn-on voltages of 2.7–2.9 V, and maximum luminance efficiencies of up to 3.94 cd A⁻¹ at 17.6 mA cm⁻² (maximum power efficiency of 1.62 lm W⁻¹) were prepared.     

Comparative imaging of P,S, Fe,Cu, Zn and C in thin sections of rat brain tumor as well as control tissues by laser ablation inductively coupled plasma mass spectrometry

Laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) was used for quantitative imaging of selected elements (P, S, Fe, Cu, Zn and C) in thin sections of rat brain samples (thickness 20 μm). The sample surface was scanned (raster area ~ 2 cm²) with a focused laser beam (wavelength 266 nm, diameter of laser crater 50 μm, and irradiance 1 × 10⁹ W cm^− 2). The laser ablation system was coupled to a double-focusing sector field. The possibility was evaluated of using carbon (via measurement of ¹³C⁺) as an internal standard element for imaging element distribution as part of this method. The LA-ICP-MS images obtained for P, S, Fe Cu and Zn were quantified using synthetically prepared matrix-matched laboratory standards. Depending on the sample analyzed, concentrations of Cu and Zn in the control tissue were found to be in the range of 8–10 μg g^− 1 and 10–12 μg g^− 1, while in the tumor tissue these concentrations were in the range of 12–15 μg g^− 1 and 15–17 μg g^− 1, respectively. The measurements of P, S and Fe distribution revealed the depletion of these elements in tumor tissue. In all the samples, the shape of the tumor could be clearly distinguished from the surrounding healthy tissue by the depletion in carbon. Additional experiments were performed in order to study the influence of the water content of the analyzed tissue on the intensity signal of the analyte. The results of these measurements show the linear correlation (R² = 0.9604) between the intensity of analyte and amount of water in the sample. The growth of a brain tumor was thus studied for the first time by imaging mass spectrometry.     

Direct quantification of creatinine in human urine by using isotope dilution extractive electrospray ionization tandem mass spectrometry

Urinary creatinine (CRE) is an important biomarker of renal function. Fast and accurate quantification of CRE in human urine is required by clinical research. By using isotope dilution extractive electrospray ionization tandem mass spectrometry (EESI–MS/MS) a high throughput method for direct and accurate quantification of urinary CRE was developed in this study. Under optimized conditions, the method detection limit was lower than 50 μg L⁻¹. Over the concentration range investigated (0.05–10 mg L⁻¹), the calibration curve was obtained with satisfactory linearity (R² = 0.9861), and the relative standard deviation (RSD) values for CRE and isotope-labeled CRE (CRE-d3) were 7.1–11.8% (n = 6) and 4.1–11.3% (n = 6), respectively. The isotope dilution EESI–MS/MS method was validated by analyzing six human urine samples, and the results were comparable with the conventional spectrophotometric method (based on the Jaffe reaction). Recoveries for individual urine samples were 85–111% and less than 0.3 min was taken for each measurement, indicating that the present isotope dilution EESI–MS/MS method is a promising strategy for the fast and accurate quantification of urinary CRE in clinical laboratories.     

The design,synthesis, and characterization of D-π-A-π-A type organic dyes as sensitizers for dye-sensitized solar cells (DSSCs)

New D-π-A-π-A type organic dyes were synthesized and characterized as sensitizers for dye-sensitized solar cells (DSSCs). These dyes showed wide absorption spectra (300–625 nm) and high molar extinction coefficients (ε_467 nm = 60,911 M⁻¹ cm⁻¹). As dye sensitizers in DSSC, the D-π-A-π-A dye having a cyanoacrylic acid as an acceptor gave the best cell performance with a short-circuit photocurrent density (J_sc) of 7.14 mA/cm², an open-circuit voltage (V_oc) of 0.62 V, and a fill factor (FF) of 0.72, corresponding to an overall conversion efficiency η of 3.19%.     

Amperometric sensing of norepinephrine at picomolar concentrations using screen printed,high surface area mesoporous carbon

Norepinephrine (NE) is detected amperometrically using the enzyme Phenylethanolamine N-methyl transferase and cofactor S-(5′-Adenosyl)-l-methionine chloride dihydrochloride with disposable screen printed mesoporous carbon electrodes. The role of internal surface area and pore size of the mesoporous carbon is systematically examined using soft-templated, mesoporous silica–carbon powders with highly microporous walls obtained from etching of the silica to produce powders with surface areas ranging from 671–2339 m² g⁻¹. As the surface area increases, the sensitivity of the biosensor at very low NE concentrations (0–500 pg mL⁻¹) in phosphate buffered saline (PBS) increases just as the current signal increases with respect to the NE concentration of 81–1581 μA mL ng⁻¹ cm⁻² for the mesoporous carbons. The best performing electrode provides similar sensitivity in whole rabbit blood in comparison to PBS despite no membrane layer to filter the non-desired reactants; the small (<5 nm) pore size and large internal surface area acts to minimize non-specific events that decrease sensitivity.