Pressurised membrane-assisted liquid extraction of UV filters from sludge

A method for the determination of 11 UV-filter compounds in sludge has been developed and evaluated. The procedure includes the use of non-porous polymeric membranes in combination with pressurised liquid extraction (PLE). Firstly, the solid sample, wetted with the extraction solvent, was enclosed into tailor-made bags prepared with low density polyethylene. Secondly, these packages were submitted to a conventional PLE (70 °C, 4 cycles of 5 min static time). Finally, the analytes were determined by liquid chromatography–atmospheric pressure photoionisation–tandem mass spectrometry. The main advantage of this procedure is the reduction of time, solvent and labour effort ought to the combination of extraction and clean-up in a single step. Although the extraction is not quantitative (thus, standard addition is recommended for quantification) selectivity is clearly gained using the membrane as a consequence of the differences of permeation and transport through the membrane between the analytes and other sample matrix components. The optimised protocol provides limits of detection ranging from 0.3 ng g⁻¹ (ethylhexyl dimethyl p-aminobenzoate (OD-PABA)) to 25 ng g⁻¹ (ethylhexyl triazone (EHT)) with only 0.5 g of sludge sample. All the studied UV filters were found in the samples at concentration levels between 1.4 and 2479 ng g⁻¹, emphasising the high adsorption potential of this kind of environmental pollutants onto solid samples such as sludge. Also, this method has permitted the determination of seven of the studied UV filters in sludge samples for the first time.     

A strategy for the systematic development of a liquid chromatographic mass spectrometric screening method for polymer electrolyte membrane degradation products using isocratic and gradient phase optimized liquid chromatography

Within the scope of research for target and non-target LC–MS/MS analysis of membrane degradation products of polymer electrolyte membrane fuel cells, a systematic method development for the separation of structurally similar compounds was performed by phase optimized liquid chromatography. Five different stationary phases with different selectivities were used. Isocratic separation for 4-hydroxybenzoic acid, isophthalic acid, terephthalic acid, 4-hydroxybenzaldehyde and 4-formylbenzoic acid was achieved on a C18 and a Phenyl phase. Using the PRISMA model the separation efficiency was optimized. This was achieved on a serially connected mixed stationary phase composed of 30 mm C18, 150 mm Phenyl and 60 mm C30. For the LC–MS screening of unknown degradation products from polymer electrolyte membranes in the product water of a fuel cell, a solvent gradient is mandatory for less polar or later eluting compounds. By means of 4-mercaptobenzoic acid it could be shown that a solvent gradient can be applied in order to elute later eluting compounds in a short time. The adaptability of this method for the qualitative analysis by target and non-target LC–MS/MS screening has been shown by means of 4-hydroxybenzoic acid. The combination of solvent gradient and isocratic conditions makes this approach attractive for the purpose of a screening method for known and unknown analytes in a water sample.     

Design of guanidinium ionic liquid based microwave‐assisted extraction for the efficient extraction of Praeruptorin A from Radix peucedani

A series of novel tetramethylguanidinium ionic liquids and hexaalkylguanidinium ionic liquids have been synthesized based on 1,1,3,3‐tetramethylguanidine. The structures of the ionic liquids were confirmed by ¹H NMR spectroscopy and mass spectrometry. A green guanidinium ionic liquid based microwave‐assisted extraction method has been developed with these guanidinium ionic liquids for the effective extraction of Praeruptorin A from Radix peucedani. After extraction, reversed‐phase high‐performance liquid chromatography with UV detection was employed for the analysis of Praeruptorin A. Several significant operating parameters were systematically optimized by single‐factor and L₉ (3⁴) orthogonal array experiments. The amount of Praeruptorin A extracted by [1,1,3,3‐tetramethylguanidine]CH₂CH(OH)COOH is the highest, reaching 11.05 ± 0.13 mg/g. Guanidinium ionic liquid based microwave‐assisted extraction presents unique advantages in Praeruptorin A extraction compared with guanidinium ionic liquid based maceration extraction, guanidinium ionic liquid based heat reflux extraction and guanidinium ionic liquid based ultrasound‐assisted extraction. The precision, stability, and repeatability of the process were investigated. The mechanisms of guanidinium ionic liquid based microwave‐assisted extraction were researched by scanning electron microscopy and IR spectroscopy. All the results show that guanidinium ionic liquid based microwave‐assisted extraction has a huge potential in the extraction of bioactive compounds from complex samples.     

Optimisation of pressurised liquid extraction by experimental design for quantification of pesticides and alkyl phenols in sludge,suspended materials and atmospheric fallout by liquid chromatography–tandem mass spectrometry

The study proposes an analytical method to quantify 10 alkylphenols and 12 pesticides at ultra-trace levels by liquid chromatography in reverse mode coupled to positive electrospray ionisation–tandem mass spectrometry. The extraction procedure from environmental solids was optimised by pressurised liquid extraction using acetonitrile:isopropanol (1:1, v/v). The influence of several extraction experimental factors, temperature, pressure, duration and number of cycles, related to the PLE was investigated by an original and efficient chemometric approach. The optimised extraction method (80 °C, 40 bar, 10 min, 1 cycle) exhibited recoveries between 67 and 127% with RSD mostly under 13%. The whole method was applied to real samples: sludge, suspended materials, atmospheric fallouts and roof deposit. Pollutant levels were between 1 μg kg⁻¹ and 5.9 mg kg⁻¹.     

Determination of 2,6-dichlorobenzamide and its degradation products in water samples using solid-phase extraction followed by liquid chromatography–tandem mass spectrometry

An analytical method was developed for the determination of 2,6-dichlorobenzamide (BAM) and five degradation products thereof including 2-chlorobenzamide (OBAM), 2,6-dichlorobenzoic acid (DCBA), 2-chlorobenzoic acid (OBA), benzoic acid (BA) and benzamide (BAD) in water samples. Solid-phase extraction was combined with liquid chromatography coupled to tandem mass spectrometry using electrospray ionisation. Groundwater spiked at a concentration of 1.0 μg/L gave recoveries on day 1 between 91 and 102% (relative standard deviation: 2.2–26.5%) for OBAM, BAM, DCBA, BA and OBA, while BAD showed a somewhat lower recovery of 60% (relative standard deviation: 25%). Corresponding figures on day 3 gave recoveries of 97–110% (relative standard deviation: 3–22%) for OBAM, BAM, DCBA, BA and OBA, while BAD had a recovery of 51% (relative standard deviation: 4%). The final SPE-LC–MS/MS method had a LOD_Method of 0.009, 0.007, 0.010, 0.021, 0.253 and 0.170 μg/L groundwater for BAD, OBAM, BAM, DCBA, BA and OBA and a LOQ_Method of 0.030, 0.023, 0.035, 0.071, 0.842 and 0.565 μg/L groundwater in the same order of appearance. Analysis of three different Danish groundwaters confirmed the occurrence of BAM at levels exceeding the threshold value of 0.1 μg/L, while no degradation products were found above LOD_Method.     

In situ derivatization–liquid liquid extraction as a sample preparation strategy for the determination of urinary biomarker prolyl‐4‐hydroxyproline by liquid chromatography–tandem mass spectrometry

Polar analytes that possess protic functional groups have often been treated with alkyl chloroformates to decrease their polarity and increase their volatility prior to gas chromatography–mass spectrometry analysis. This derivatization reaction has two distinct advantages. It proceeds smoothly in aqueous media, and the desired reaction products are efficiently separated from interfering ionic components by their extraction into a water‐immiscible organic phase. In the present work, the derivatization–liquid liquid sample preparation was examined in detail for analysis of a potential urinary dipeptide biomarker l ‐prolyl‐4‐l ‐hydroxyproline (PHP) by downstream liquid chromatography coupled to electrospray mass spectrometry. PHP was treated with a series of alkyl and fluoroalkyl chloroformates in aqueous media, and the detected reaction products were investigated. Smooth conversion of PHP into the N‐isobutyloxycarbonyl isobutyl ester was accomplished by the coupled action of isobutanol, isobutyl chloroformate and the pyridine catalyst. This derivative afforded a highest detector response from all the derivatized forms examined, including the nonderivatized PHP. A simple isocratic elution on a common RP‐C18 HPLC column coupled with tandem mass spectrometry, and use of the synthesized heptadeuterated analog (D7‐PHP) as an internal standard, enabled validation of the method and determination of PHP in human urine in less than 5 min. The in situ derivatization–liquid liquid extraction has thus been demonstrated to be a useful sample preparation strategy for the analysis of polar metabolites by liquid chromatography–tandem mass spectrometry in the complex urine matrix. Copyright © 2012 John Wiley & Sons, Ltd.     

Room temperature imidazolium ionic liquid: a solvent for extraction of carbamates prior to liquid chromatographic analysis

A simple and rapid method for preconcentration of carbamate insecticides, including methomyl, propoxur, carbofuran, carbaryl, isoprocarb, methiocarb and promecarb, has been developed. It was based on a liquid-liquid microextraction using a [C₄MIM][PF₆] room temperature ionic liquid as an extraction solvent prior to analysis by high performance liquid chromatography with UV detection. Experimental parameters affecting the extraction performance, such as the volumes of sample, extractant and dissolving solvent, and extraction time, were studied. Under the selected conditions, the enrichment factors in the range between 10 and 25 could be achieved with the limit of detection in the range of 2-40 μg L⁻¹, and with the relative standard deviations of lower than 0.6 and 10.2% for retention time and peak area, respectively. The proposed method offers advantages in reduction of the exposure danger to toxic solvents used in the conventional liquid-liquid extraction, simplicity of the extraction processes, rapidity, and sensitivity enhancement. The method was demonstrated to apply to the analysis of fruit and natural surface water samples.     

Comparison of different imidazolium supported ionic liquid polymeric phases with strong anion-exchange character for the extraction of acidic pharmaceuticals from complex environmental samples

Two imidazolium supported ionic liquid phases (SILPs) containing different anions, trifluoromethanesulphonate [CF(3) SO(3) (-) ], and tetrafluoroborate [BF(4) (-) ], were synthesized and evaluated as solid-phase extraction sorbents for extracting acidic pharmaceuticals from aqueous samples under strong anion-exchange conditions, which include an effective cleanup of the sample. The best SILP material [MI(+) ][CF(3) SO(3) (-) ] was selected and successfully applied to the determination of acidic pharmaceuticals in different types of water samples (river water and effluent wastewater). The results were then compared to the previously synthesized SILP material based on [MI(+) ][CF(3) COO(-) ] and the commercially available Oasis MAX sorbent.     

Polyimidazolyl acetate ionic liquid grafted on cellulose filter paper as thin-film extraction phase for extraction of non-steroidal anti-inflammatory drugs from water

Recently, pharmaceuticals and personal care products in the water environment exhibited potential risks to both human and aquatic organisms. In order to improve the sensitivity and accuracy of pharmaceutical detection, the polyimidazolyl acetate ionic liquid was synthesized by Radziszewski reaction and coated on cellulose filter papers as a thin-film extraction phase for extraction of non-steroidal anti-inflammatory drugs from water. The attenuated total reflection-infrared spectrometry, thermogravimetric analysis, and scanning electron microscope analyses demonstrated that the polyimidazolyl acetate ionic liquid was successfully prepared and attached to the surface of the cellulose filter paper through chemical bonding. The adsorption capacity of the homemade thin-film extraction material for the four non-steroidal anti-inflammatory drugs was greater than 8898 ng/cm² under the optimum conditions, and the desorption rate was over 90%. Then, a paper-based thin-film extraction phase-high-performance liquid chromatography-tandem mass spectrometry method was established for the extraction of non-steroidal anti-inflammatory drugs in water. This method provided limits of detection and limits of quantification were in the range of 0.02–0.15 and 0.17–0.50 μg/L, respectively. Hence, the obtained thin-film extraction phase showed excellent recovery and reproducibility for the target non-steroidal anti-inflammatory drugs with carboxyl groups from water.     

Optimization of temperature-controlled ionic liquid dispersive liquid phase microextraction combined with high performance liquid chromatography for analysis of chlorobenzenes in water samples

Temperature-controlled ionic liquid dispersive liquid phase microextraction (TCIL-DLPME) combined with high performance liquid chromatography-diode array detection (HPLC-DAD) was applied for preconcentration and determination of chlorobenzenes in well water samples. The proposed method used 1-butyl-3-methylimidazolium hexafluorophosphate ([C₄mim][PF₆]) as the extraction solvent. The effect of different variables on extraction efficiency was studied simultaneously using an experimental design. The variables of interest in the TCIL-DLPME were extraction solvent volume, salt effect, solution temperature, extraction time, centrifugation time, and heating time. The Plackett-Burman design was employed for screening to determine the variables significantly affecting the extraction efficiency. Then, the significant factors were optimized by using a central composite design (CCD) and the response surface equations were developed. The optimal experimental conditions obtained from this statistical evaluation included: extraction solvent volume, 75 μL; extraction time, 20 min; centrifugation time, 25 min; heating time, 4 min; solution temperature, 50 °C; and no addition of salt. Under optimal conditions, the preconcentration factors were between 187 and 298. The limit of detections (LODs) ranged from 0.05 μg L⁻¹ (for 1,2-dichlorobenzene) to 0.1 μg L⁻¹ (for 1,2,3-trichlorobenzene). Linear dynamic ranges (LDRs) of 0.5-300 and 0.5-500 μg L⁻¹ were obtained for dichloro- and trichlorobenzenes, respectively. The performance of the method was evaluated for extraction and determination of chlorobenzenes in well water samples in micrograms per liter and satisfactory results were obtained (RSDs < 9.2%).     

Preparation of stir cake sorptive extraction based on polymeric ionic liquid for the enrichment of benzimidazole anthelmintics in water,honey and milk samples

In this work, a new stir cake sorptive extraction (SCSE) using polymeric ionic liquid monolith as sorbent was prepared. The sorbent was obtained by in situ copolymerization of an ionic liquid, 1-allyl-3-methylimidazolium bis[(trifluoro methyl)sulfonyl]imide (AMII) and divinylbenzene (DB) in the presence of N,N-dimethylformamide. The influence of the content of ionic liquid and the porogen in the polymerization mixture on extraction performance was studied thoroughly. The physicochemical properties of the polymeric ionic liquid were characterized by infrared spectroscopy, elemental analysis, scanning electron microscopy and mercury intrusion porosimetry. The usefulness of SCSE–AMIIDB was demonstrated by the enrichment of trace benzimidazole anthelmintics. Several parameters affecting the extraction efficiency were investigated, and under the optimized conditions, a simple and effective method for the determination of trace benzimidazoles residues in water, milk and honey samples was established by coupling SCSE–AMIIDB with high performance liquid chromatography/diode array detection (SCSE–AMIIDB–HPLC/DAD). Results indicated that the limits of detection (S/N = 3) for target compounds were 0.020–0.072 μg L⁻¹, 0.035–0.10 μg L⁻¹ and 0.026–0.076 μg L⁻¹ in water, milk and honey samples, respectively. In addition, an acceptable reproducibility was achieved by evaluating the repeatability and intermediate precision with relative standard deviations (RSD) of less than 9% and 11%, respectively. Finally, the established AMII–SCSE–HPLC/DAD method was successfully applied for the determination of benzimidazoles residues in milk, honey and environmental water samples. Recoveries obtained for the determination of benzimidazole anthelmintics in spiking samples ranged from 70.2% to 117.6%, with RSD below 12% in all cases.     

Temperature‐controlled ionic liquid dispersive liquid‐phase microextraction for the sensitive determination of triclosan and triclocarban in environmental water samples prior to HPLC‐ESI‐MS/MS

A novel dispersive liquid‐phase microextraction method without dispersive solvents has been developed for the enrichment and sensitive determination of triclosan and triclocarban in environmental water samples prior to HPLC‐ESI‐MS/MS. This method used only green solvent 1‐hexyl‐3‐methylimidazolium hexafluorophosphate as extraction solvent and overcame the demerits of the use of toxic solvents and the instability of the suspending drop in single drop liquid‐phase microextraction. Important factors that may influence the enrichment efficiencies, such as volume of ionic liquid, pH of solutions, extraction time, centrifuging time and temperature, were systematically investigated and optimized. Under optimum conditions, linearity of the method was observed in the range of 0.1–20 μg/L for triclocarban and 0.5–100 μg/L for triclosan, respectively, with adequate correlation coefficients (R>0.9990). The proposed method has been found to have excellent detection sensitivity with LODs of 0.04 and 0.3 μg/L, and precisions of 4.7 and 6.0% (RSDs, n=5) for triclocarban and triclosan, respectively. This method has been successfully applied to analyze real water samples and satisfactory results were achieved.     

Identification of G‐nerve agents at picogram levels from complex organic samples containing hydrocarbon interferences by aqueous extraction,followed by derivatization and liquid chromatography‐mass spectrometry analysis

The chromatograms obtained from the gas chromatography‐electron ionization mass spectrometric (GC‐EI‐MS) analysis of extracts containing G‐nerve agents in the presence of diesel, gasoline, etc., are dominated by hydrocarbon backgrounds that “mask” the G‐nerve agents, leading to severe difficulties in identification. This paper presents a practical solution for this challenge by transferring the G‐nerve agents from the organic phase into the aqueous phase using liquid‐liquid extraction (LLE), followed by derivatization with 2‐[(dimethylamino)methyl]phenol (2‐DMAMP), allowing ultrasensitive LC‐ESI‐MS/MS analysis of the G‐derivatives. The proposed approach enables rapid identification of trace amounts of G‐nerve agents with limits of identification (LOIs) at the pg/mL scale.     

Extraction of proteins from biological fluids by use of an ionic liquid/aqueous two-phase system

An ionic liquid/aqueous two-phase system based on the hydrophilic ionic liquid 1-butyl-3-methylimidazolium chloride (BmimCl) and K(2)HPO(4) has been employed for direct extraction of proteins from human body fluids for the first time. Proteins present at low levels were quantitatively extracted into the BmimCl-rich upper phase with a distribution ratio of about 10 between the upper and lower phase and an enrichment factor of 5. Addition of an appropriate amount of K(2)HPO(4) to the separated upper phase results in a further phase separation, giving rise to an improved enrichment factor of 20. FTIR and UV spectroscopy demonstrated that no chemical (bonding) interactions between the ionic liquid and the protein functional groups were identifiable, while no alterations of the natural properties of the proteins were observed. The partitioning of proteins in the two-phase system was assumed to have been facilitated by the electrostatic potential difference between the coexisting phases, as well as by salting out effects. The system could be applied successfully for the quantification of proteins in human urine after on-line phase separation in a flow system. The use of an ionic liquid, as a green solvent, offers clear advantages over traditional liquid-liquid extractions, in which the use of toxic organic solvents is unavoidable.     

Development of an ultra-high-performance liquid chromatography-tandem mass spectrometry method for high throughput determination of organophosphorus flame retardants in environmental water

Widely used as flame retardants, organophosphate esters (OPEs) are now broadly present in the indoor and outdoor environments. Currently available liquid chromatography-tandem mass spectrometry (LC-MS/MS) methods share some drawbacks with gas chromatography (GC) methods, including time consuming, limited target OPEs, incomplete separation capability for some OPEs and low throughput. In this study, a fast and high throughput LC-MS/MS method was developed. For the first time, all the twelve OPEs that have been studied in literature, ranging from the very polar and volatile trimethyl phosphate to the very hydrophobic and non-volatile tris(2-ethylhexyl) phosphate, were separated within 11 min. Different from previous studies, we found that the blank contamination was mainly from organic mobile phase rather than the enrichment process, and it can be efficiently eliminated by using acetonitrile rather than methanol as the organic phase of the mobile phase. The signal to noise ratio (S/N) was significantly improved by using 0.1% formic acid as an organic modifier. The method exhibited high throughput and sensitivity and can baseline separate 11 of the 12 OPEs studied within 11 min with LOQs ranging from 2 to 6 ng/L. The relative standard deviations were in the range of 2-10%. For both reagent water and river water, the spiked recoveries of OPEs ranged from 70 to 110%, except for the very polar and volatile trimethyl phosphate that has recovery below 10%. The developed procedure was successfully applied to study the OPE contamination of the Songhua River, and it was found that all the target OPEs were detected with total concentrations of around 1 μg/L in the river waters.     

On-line solid-phase extraction of large-volume injections coupled to liquid chromatography-tandem mass spectrometry for the quantitation and confirmation of 14 selected trace organic contaminants in drinking and surface water

We describe the development and validation of an on-line solid-phase extraction of large-volume injections coupled to liquid chromatography-tandem mass spectrometry method for the simultaneous quantitation and confirmation of 14 selected trace organic contaminants in drinking and surface water. Selected compounds were: anti-infectives (clarithromycin, sulfamethoxazole and trimethoprim), an anticonvulsant (carbamazepine) and its transformation product 10,11-dihydrocarbamazepine, an antihypertensive (enalapril), antineoplastics (cyclophosphamide and methotrexate), herbicides (atrazine, cyanazine, and simazine) and two of their transformation products (deethylatrazine and deisopropylatrazine) and an antiseptic (triclocarban). The breakthrough volume determinations showed that out of all the investigated sorbents, the Strata-X on-line solid-phase extraction column showed the best performance. The method used a load volume of 10.0 mL and was validated using the corresponding matrices, yielding for most compounds, R² > 0.99. Extraction recoveries ranged from 60 to 109%. The intra- and inter-day precision were <14 and <16%, respectively. The method detection limits ranged from 0.6 to 6 ng L⁻¹. Matrix effects were in general low. The performance of the on-line method was demonstrated with the analysis of real water samples. The application of alternative techniques of confirmation was also explored using accurate mass measurements on a time-of-flight mass spectrometer and the data-dependent reverse energy ramp scan on a triple quadrupole.     

Matrix solid‐phase dispersion coupled with homogeneous ionic liquid microextraction for the determination of sulfonamides in animal tissues using high‐performance liquid chromatography

Matrix solid‐phase dispersion coupled with homogeneous ionic liquid microextraction was developed and applied to the extraction of some sulfonamides, including sulfamerazine, sulfamethazine, sulfathiazole, sulfachloropyridazine, sulfadoxine, sulfisoxazole, and sulfaphenazole, in animal tissues. High‐performance liquid chromatography was applied to the separation and determination of the target analytes. The solid sample was directly treated by matrix solid‐phase dispersion and the eluate obtained was treated by homogeneous ionic liquid microextraction. The ionic liquid was used as the extraction solvent in this method, which may result in the improvement of the recoveries of the target analytes. To avoid using organic solvent and reduce environmental pollution, water was used as the elution solvent of matrix solid‐phase dispersion. The effects of the experimental parameters on recoveries, including the type and volume of ionic liquid, type of dispersant, ratio of sample to dispersant, pH value of elution solvent, volume of elution solvent, amount of salt in eluate, amount of ion‐pairing agent (NH₄PF₆), and centrifuging time, were evaluated. When the present method was applied to the analysis of animal tissues, the recoveries of the analytes ranged from 85.4 to 118.0%, and the relative standard deviations were lower than 9.30%. The detection limits for the analytes were 4.3–13.4 μg/kg.     

Development of a high‐throughput method based on thin‐film microextraction using a 96‐well plate system with a cork coating for the extraction of emerging contaminants in river water samples

In this study, a new method was developed in which a biosorbent material is used as the extractor phase in conjunction with a recently described sample preparation technique called thin‐film microextraction and a 96‐well plate system. The method was applied for the determination of emerging contaminants, such as 3‐(4‐methylbenzylidene) camphor, ethylparaben, triclocarban, and bisphenol A in water samples. The separation and detection of the analytes were performed by high‐performance liquid chromatography with diode array detection. These contaminants are considered hazardous to human health and other living beings. Thus, the development of an analytical method to determine these compounds is of great interest. The extraction parameters were evaluated using multivariate and univariate optimization techniques. The optimum conditions for the method were 3 h of extraction time, 20 min of desorption with 300 μL of acetonitrile and methanol (50:50, v/v), and the addition of 5% w/v sodium chloride to the sample. The analytical figures of merit showed good results with linear correlation coefficients higher than 0.99, relative recoveries of 72–125%, interday precision (n = 3) of 4–18%, and intraday precision (n = 9) of 1–21%. The limit of detection was 0.3–5.5 μg/L, and the limit of quantification was 0.8–15 μg/L.     

液相色谱-四极杆-飞行时间串联质谱法高通量分析美国红参的脑苷脂分子种

利用液相色谱-四极杆-飞行时间串联质谱法(LC-Q-TOF MS/MS)分析美国红参(Parastichopus californicus)脑苷脂的分子种组成。以氯仿-甲醇(2：1,v/v)溶液提取,经皂化和固相萃取柱(SPE)净化后,在正离子模式下,通过自动二级质谱方式同时获取样品脑苷脂分子的一级和二级质谱图。筛取含180 Da中性丢失碎片的分子,再结合二级质谱中的长链碱和脂肪酸碎片,确定每种脑苷脂分子的结构。通过该法一次性共分析出123种美国红参脑苷脂分子种;含有的长链碱共18种,其中植物鞘氨醇型与鞘氨醇型长链碱的相对含量比为1：2;脂肪酸为18~25碳的饱和或单不饱和脂肪酸,以24碳脂肪酸为主,2-羟基脂肪酸占58.62%,饱和与单不饱和脂肪酸的相对含量比约为1：3。LC-Q-TOF MS/MS法分析海参脑苷脂分子种的灵敏度高,准确,简便,为海参脑苷脂的构效关系研究及功能食品开发提供理论依据。     

A supported liquid extraction LC–MS/MS method for determination of concentrations of GDC‐0425, a small molecule Checkpoint kinase 1 inhibitor,in human plasma

A liquid chromatography–tandem mass spectrometry (LC–MS/MS) method for the determination of GDC‐0425 concentrations in human plasma has been developed and validated. Supported liquid extraction was used to extract plasma samples (50 μL) and the resulting samples were analyzed using reverse‐phase chromatography and mass spectrometry coupled with a turbo‐ionspray interface. The mass analysis of GDC‐0425 was performed using multiple reaction monitoring transitions in positive ionization mode. The method was validated over the calibration curve range of 1.00–1000 ng/mL using linear regression and 1/x² weighting. Within‐run relative standard deviation ranged from 0.8 to 5.1%, while between‐run RSD varied from 1.9 to 4.7% for QCs. The accuracy ranged from 90.0 to 101.0% of nominal for within‐run and from 94.0 to 100.0% of nominal for between‐run. Overall extraction recovery was 87.4% for GDC‐0425 and 87.9% for GDC‐0425‐d₉. Stability of GDC‐0425 was established in human plasma for 374 days at ?20 and ?70 °C and established in reconstituted sample extracts for 88 h when stored at 2–8 °C. Stable‐labeled internal standard was used to minimize matrix effects. This assay was used to characterize the pharmacokinetics of GDC‐0425 in cancer patients.