Polypropylene/poly(butyl methacrylate) blends prepared by diffusion and subsequent polymerization of butyl methacrylate in isotactic polypropylene pellets

Polypropylene/poly(butyl methacrylate)(PP/PBMA) blends were prepared by diffusion and subsequent polymerization of butyl methacrylate(BMA) in commercial isotactic polypropylene(iPP) pellets.The diffusion kinetics,diametrical distribution of PBMA in a pellet and phase morphology of a typical PP/PBMA blend were investigated.     

Selective distribution,reinforcement, and toughening roles of MWCNTs in immiscible polypropylene/ethylene‐co‐vinyl acetate blends

Polypropylene/ethylene‐co‐vinyl acetate (PP/EVA) nanocomposites with functionalized multiwalled carbon nanotubes (FMWCNTs) have been prepared. The dissolution experiment, transmission electronic microscope, and scanning electronic microscope characterizations prove that, in the nanocomposites with sea–island morphology, although some FMWCNTs are observed in both PP and EVA phases, most of FMWCNTs distribute at the interface; however, in the nanocomposites with cocontinuous morphology, FMWCNTs mainly distribute in EVA phase. Further results based on (differential scanning calorimetry) measurements show that the different dispersion states of FMWCNTs, which are resulted by the different melt blending sequences, result in the different crystallization behaviors of PP matrix. The mechanical measurements show that FMWCNTs exhibit apparent reinforcement and toughening effects for immiscible PP/EVA blends, and such effects are greatly dependent upon the blending sequences. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1882–1892, 2010     

Migration of nanosilica particles in polymer blends

Hydrophilic pyrogenic silica melt mixed in immiscible polypropylene/poly (ethylene‐co‐vinyl acetate) (PP/EVA) blend was found to migrate from the PP matrix to the EVA dispersed domains and remained confined inside them. Surprisingly, it was shown than silica was also able to migrate from a dispersed PP phase to an EVA matrix but this transfer was slower and not complete. The same silica with a hydrophobic surface treatment moved and accumulated to the blend interface and in PP. The mechanisms from which this migration proceeds are discussed. Whereas self diffusion of the particles was shown to have almost no effect, shear induced movements and collisions with dispersed drops is believed to be the most efficient mechanism. The possible trapping of silica aggregates during droplet–droplet coalescence was impossible to observe but is thought to be a possible additional mechanism. No quantification on the relative importance of the latter phenomenon can be drawn at the moment. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1976–1983, 2008     

An investigation on the dispersion of montmorillonite (MMT) primary particles in PP matrix

A novel path of preparing PP/o-MMT nanocomposites, which pay attention to the breaking up of MMT original agglomerates and dispersing of its primary particles, rather than the intercalation or exfoliation degree of o-MMT, was reported. The method of predispersing the o-MMT particles into a polar poly(vinyl alcohol) (PVA) matrix and then melt blending the pre-treated PVA/o-MMT hybrids with PP was studied. 3-Isopropenyl-α,α-dimethylbenzene-isocyanate (TMI) was used as a modifier of PVA to improve the compatibility between PVA and PP matrix. Pre-disperse o-MMT with TMI modified PVA was proved to be an effective way to get a composite with fine o-MMT particles dispersion. But the method, which is pre-dispersing o-MMT with non modified PVA and then using TMI to modify such PVA/o-MMT hybrid, would largely reduce the reaction degree between TMI and PVA because of the relatively lower reaction temperature. Although the latter method also can obtain finer dispersion composites than that with using PP-g-MAH as compatibilizer, the relatively higher degradation degree of PP matrix in this method will limit the use of this nanocomposite.     

The influence of UV light on collagen/poly(ethylene glycol) blends

The photodegradation behaviour of the collagen and poly(ethylene glycol) PEG blends has been studied by Fourier transform infrared spectroscopy (FTIR), UV-Vis spectroscopy and viscometry. Surface properties before and after UV irradiation were observed using optical microscope.Collagen and PEG were immiscible and the films obtained from the mixture were fragile with poor mechanical properties. The photochemical stability of the collagen and PEG blend was different from that of the single components. In general collagen/PEG blends are less stable under UV irradiation than pure collagen. The influence of PEG on the photochemical stability of collagen depends on its concentration in the blend. Microscope photographs showed that the surface characteristics of collagen and collagen/PEG blends in film form are not drastically altered after UV irradiation.     

Thermal analysis of polysiloxanes, aromatic polyimide and their blends

Low molecular weight poly(dimethylsiloxane) and poly(methylphenylsiloxane) were synthesized and blended with polyimide (PI) at its precursor poly(amic acid) stage. FTIR analysis has proven the retention of polysiloxanes in polyimide after the ultimate curing of blends. Differential scanning calorimetric analysis was performed on polysiloxanes to elucidate the structures present in polymers while thermogravimetric analysis (TGA) was performed on polysiloxanes, polyimide as well as their blends to evaluate the thermal stability and to analyze the effect of polysiloxane incorporation in blends. Blends have shown synergistic improvement as compared to neat polyimide.     

含硫醚可溶性聚芳醚酮的合成及电子束辐照的研究

聚醚醚酮(PEEK)因具有优异的机械性能、耐热性、耐化学腐蚀性等优点而广泛应用于航空航天、电子器件、机械仪表等领域．具有刚性结构的聚醚醚酮有极好的耐溶剂性,不溶于一般的有机溶剂,并且需在较高的温度下进行加工．近20年来,人们不断开发性能优异的聚醚醚酮新材料,在聚合物主链上引入不同的功能基团(如萘环、氮杂萘环等)及侧基功能基团(如苯、三氟甲基等),以提高聚芳醚酮的溶解性,或者通过共聚和共混等方式进一步改善材料的使用性能和加工性能,     

Radiation degradation of blends polypropylene/poly(ethylene-co-vinyl acetate)

Physicochemical and mechanical characteristics of irradiated electron beam polypropylene/ethylene-vinyl acetate (PP/EVA) blends and individual components were investigated. Although oxidation of alkyl radicals in the blends proceeds slower than in PP, the total oxidation effect monitored by content of oxygen-containing groups shows opposite tendency. Blending with EVA does not affect degree of PP crystallinity. The enthalpy of melting and crystallization of the blends reveal phase separation between dispersed copolymer and PP matrix. In all studied blends, degradation prevails over tendency of EVA to cross-linking.     

Preparation of degradable polypropylene by an addition of poly(ethylene oxide) microcapsule containing TiO2. Part III: Effect of existence of calcium phosphate on biodegradation behavior

In this work, biodegradation behavior of a novel polypropylene (PP) composite containing a poly(ethylene oxide) (PEO)/modified TiO₂ microcapsule was studied with an oxo-biodegradation test combined with a photodegradation treatment (using a high-pressure mercury vapor lamp for 24 h of the irradiation at 30 °C in air) and a soil burial test (for 45 days of incubation at 20 °C). The modification of the TiO₂ was performed by the synthesis of octacalcium phosphate intercalated with succinic acid ion (OCPC). The existence of the microcapsule brought about higher PP photo- and biodegradation rates. In the photodegraded PP composite, active colonies of some microorganisms were observed. By comparing with the PP composite without the OCPC modification, it was found that the active behavior of the microorganisms was due to the inorganic phosphates, which were supplied by the dissolution of the OCPC during the photodegradation. In addition, the photodegraded parts in the composite were completely metabolized by the microorganisms. However, the microorganisms had the inability to metabolize other parts such as the PP crystalline phase.     

Thermal behaviour of styrene butadiene rubber/poly(ethylene-co-vinyl acetate) blends

The thermal behaviour of styrene butadiene rubber (SBR)/poly (ethylene-co-vinyl acetate) (EVA) blends was studied by using thermogravimetry (TG) and differential scanning calorimetry (DSC). The effects of blend ratio, cross-linking systems and compatibilization on the thermal stability and phase transition of the blends were analyzed. It was found that the mass loss of the blends at any temperature was lower than that of the components, highlighting the advantage of blending SBR and EVA. The addition of compatibilizer was also found to improve the thermal stability. DSC studies indicated the thermodynamic immiscibility of SBR/EVA system even in the presence of the compatibilizer. This is evident from the presence of two different glass transition temperatures, corresponding to SBR and EVA phases in both compatibilized and uncompatibilized blends.     

聚碳酸1,2-丙二酯/聚琥珀酸丁二酯/邻苯二甲酸二烯丙酯共混体系的研究

采用熔融共混的方法制备了聚碳酸1,2-丙二酯(PPC)/聚琥珀酸丁二酯(PBS)共混物和PPC/PBS/DAOP(邻苯二甲酸二烯丙酯)增塑共混物,对共混物的相容性、热性能、结晶性和物理机械性能进行了初步研究.研究结果表明PPC/PBS共混物为不相容体系,PPC对PBS的结晶度影响很小;PBS的加入提高了共混物的起始热分解温度(Td-5%),当共混物中PBS含量从10%增加到90%时,共混物的Td-5%可分别增加15℃到59℃.DAOP对PPC/PBS共混物有增塑作用,当PPC/PBS/DAOP的比例从30/70/0变化到30/70/30时,共混物玻璃化转变温度(Tg)下降了36.9℃.与PPC/PBS共混物相比,组成优化的DAOP增塑共混物PPC/PBS/DAOP(PPC/PBS/DAOP=30/70/5)的断裂伸长率和断裂能最大可提高31倍和34倍,分别达到655.1%和3.4 J/mm2,因此引入DAOP尽管使共混材料的热稳定性有所下降,但拓宽了PPC/PBS共混材料的使用温度窗口.     

Effect of poly(vinyl acetate) (PVAc) on thermal behavior and mechanical properties of poly(3-hydroxybutyrate)/poly(propylene carbonate) (PHB/PPC) blends

To assess the compatibility of blends of synthetic poly(propylene carbonate) (PPC), with a natural bacterial poly(3-hydroxybutyrate) (PHB), a simple casting procedure of blend was used. poly(3-hydroxybutyrate)/poly(propylene carbonate) blends are found to be incompatible according to DSC and DMA analysis. In order to improve the compatibility and mechanical properties of PHB/PPC blends, poly(vinyl acetate) (PVAc) was added as a compatibilizer. The effects of PVAc on the thermal behavior, morphology, and mechanical properties of 70PHB/30PPC blend were investigated. The results show that the melting point and the crystallization temperature of PHB in blends decrease with the increase of PVAc content in blends, the loss factor changes from two separate peaks of 70PHB/30PPC blend to one peak of 70PHB/30PPC/12PVAc blend. It is also found that adding PVAc into 70PHB/30PPC blend can decrease the size of dispersed phase from morphology analysis. The result of tensile properties shows that PVAc can increase the tensile strength and Young’s modulus of 70PHB/30PPC blend, and both the elongation at break and the tensile toughness increase significantly with PVAc added into 70PHB/30PPC.     

Gamma irradiation of high density poly(ethylene)/ethylene‐vinyl acetate/clay nanocomposites: possible mechanism of the influence of clay on irradiated nanocomposites

A further study on mechanical properties and morphology evolution of high density poly (ethylene)/ethylene‐vinyl acetate/and organically‐modified montmorillonite (HDPE/EVA/OMT) nanocomposites exposed to gamma‐rays (0–200 kGy) has been achieved. The results showed that nanocomposites have superior irradiation‐resistant properties to HDPE/EVA blend in mechanical properties. A transmission electron microscope study verified that a face‐face ordered nanostructure had been induced by gamma‐rays. The aim of this paper is to provide a possible mechanism on how the OMT influences the general properties of irradiated nanocomposites, based on the results of thermal, flammability and mechanical behavior. Three facts are postulated to be responsible for the mechanism. The first is the segregation of nano‐dispersed clay layers not only reduces polymer oxidation but prevents crosslinking reactions. The second is the nanostructure evolution induced by gamma‐rays, which may impart nanocomposites improved elasticity. The last is due to the Hofmann degradation, whose degraded products have opposite roles, accelerating polymer oxidation or promoting crosslinking reactions. These facts interact as well as compete with others. The properties of the nanocomposites strongly depended on the prevalent effects developing with increasing irradiation doses. Copyright © 2005 John Wiley & Sons, Ltd.     

Effect of temperature on the intrinsic viscosity of poly(ethylene glycol)/poly(vinyl pyrrolidone) blends in aqueous solutions

In this work the intrinsic viscosity of poly(ethylene glycol)/poly(vinyl pyrrolidone) blends in aqueous solutions were measured at 283.1–313.1 K. The expansion factor of polymer chain was calculated by use of the intrinsic viscosities data. The thermodynamic parameters of polymer solution (the entropy of dilution parameter, the heat of dilution parameter, theta temperature, polymer–solvent interaction parameter and second osmotic virial coefficient) were evaluated by temperature dependence of polymer chain expansion factor. The obtained thermodynamic parameters indicate that quality of water was decreased for solutions of poly(ethylene oxide), poly(vinyl pyrrolidone) and poly(ethylene oxide)/poly(vinyl pyrrolidone) blends by increasing temperature. Compatibility of poly(ethylene oxide)/poly(vinyl pyrrolidone) blends were explained in terms of difference between experimental and ideal intrinsic viscosity and solvent–polymer interaction parameter. The results indicate that the poly(ethylene glycol)/poly(vinyl pyrrolidone) blends were incompatible.     

Studies on fracture behaviors of immiscible polypropylene/ethylene‐co‐vinyl acetate blends with multiwalled carbon nanotubes

Immiscible polypropylene/ethylene‐co‐vinyl acetate (PP/EVA) blends with two different compositions, one (PP/EVA = 80/20) exhibits the typical sea‐island morphology and the other (PP/EVA = 60/40) exhibits the cocontinuous morphology, were prepared with different contents of f‐MWCNTs. The fracture behaviors, including notched Izod impact fracture and single‐edge notched tensile (SENT) fracture, were comparatively studied to establish the role of f‐MWCNTs in influencing the fracture toughness of PP/EVA blends. Our results showed that, for PP/EVA (80/20) system, f‐MWCNTs do not induce the fracture behavior change apparently. However, for PP/EVA (60/40) system, the fracture toughness of the blend increases dramatically with the increasing of f‐MWCNTs content. More severe plastic deformation accompanied by the fibrillar structure formation was observed during the SENT test. Furthermore, SENT test shows that the significant improvement in fracture toughness of PP/EVA (60/40) with f‐MWCNTs is contributed to the simultaneous enhancement of crack initiation energy and crack propagation energy, but largely dominated by crack propagation stage. Further results based on crystalline structures and morphologies of the blends showed that a so‐called dual‐network structure of EVA and f‐MWCNTs forms in cocontinuous PP/EVA blends, which is thought to be the main reason for the largely improved fracture toughness of the sample. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1331–1344, 2009     

Compatibilization of polypropylene/poly (ethylene oxide) blends and crystallization behavior of the blends

The compatibilization of incompatible polypropylene (PP)/poly(ethylene oxide) (PEO) blends was studied. The experimental results showed that the graft copolymer [(PP-MA)-g-PEO] of maleated PP(PP-MA) and mono-hydroxyl PEO (PEO-OH) was a good compatibilizer for the PP/PEO blends in which PP-MA also had some compatibilization. The crystallization of the blends was affected by the compatibility between PP and PEO. The interfacial behavior of the compatibilizers had an important effect on crystallization behavior of the PP/PEO blends. PEO showed fractionated crystallization in the PP/PEO blends. This behavior was studied from the view point of the theory of fractionated crystallization. © 1994 John Wiley & Sons, Inc.     

温度和pH双敏性PVME/CMCS水凝胶辐射交联制备及其性能

以聚甲基乙烯基醚(PVME)和羧甲基壳聚糖(CMCS)为原料, 采用电子束辐照交联方法制备聚甲基乙烯基醚/羧甲基壳聚糖(PVME/CMCS)水凝胶, 研究了温度、pH值、CMCS含量等对PVME/CMCS水凝胶溶胀度的影响, 同时以5-氟尿嘧啶(5-Fu)作模型药物, 初步探讨了凝胶药物释放性能. 结果表明, 辐射剂量在20—40 kGy时, 凝胶分数随辐射剂量的增加而快速增加, 辐射40 kGy以后趋于平衡. 在相同辐射剂量下, 随着体系中CMCS含量的增加, 凝胶分数反而减少. 该水凝胶具有一定的温度和pH敏感性, 其低临界溶解温度(LCST)在35 ℃左右, 并且在相同时间内和25及37 ℃下的溶胀反复可逆, 表现出较快的响应性. pH<3.0和pH>5.0时, 溶胀度较大; pH值为3.0~5.0时, 凝胶网络由于静电力收缩, 溶胀度较小. CMCS含量的增加和辐射剂量的减小均可提高凝胶载药量. 药物释放时间可通过改变体系中CMCS的含量和辐射剂量来调节.     

Tensile,fatigue and thermomechanical properties of poly(ethylene-co-vinyl acetate) nanocomposites incorporating low and high loadings of pre-swelled organically modified montmorillonite

The production of exfoliated polymer/clay based nanocomposites is crucial to obtain an actual benefit of nanoscale reinforcement in the polymer matrix. In this project, the production of exfoliated polymer/clay nanocomposite was aimed through the use of poly(ethylene-co-vinyl acetate) (EVA) copolymer as matrix and organically modified montmorillonite (O-MMT) as nanofiller. The research work involved the use of pre-swelled technique through magnetic stirring and ultra-sonication to obtain more readily exfoliated and dispersed O-MMT nanofiller for EVA nanocomposite production. The aims were to allow the improvement in O-MMT exfoliation and dispersion when the nanofiller was incorporated in high loading (greater than 3 wt%) into the copolymer. The original and pre-swelled O-MMTs were employed to produce the EVA/O-MMT nanocomposites with 1, 3, 5, 7 and 9 wt% nanofiller by melt compounding technique. The results of TEM, tensile and fatigue tests, XRD, FTIR and DMA proved that the pre-swelling technique applied on the O-MMT before melt compounding with the EVA copolymer can bring positive impact to the performance of the nanocomposite. As opposed to the original O-MMT, the pre-swelled O-MMT has the ability to improve the tensile toughness, cyclic stability and storage modulus of the EVA copolymer even when high O-MMT loading (7 wt %) was employed. Improvement in the EVA - O-MMT interactions in the nanocomposite system was postulated to be the main reason for such observations.     

Properties of immiscible and ethylene-butyl acrylate-glycidyl methacrylate terpolymer compatibilized poly (lactic acid) and polypropylene blends

Poly(lactic acid) (PLA) and polypropylene (PP) blends of various proportions were prepared by melt-compounding. The miscibility, phase morphology, thermal behavior, and mechanical and rheological properties of the blends were investigated. The blends were immiscible systems with two typical morphologies, spherical droplet and co-continuous, and could be obtained at various compositions. Complex viscosity, storage modulus and loss modulus depend on the PP content. Thermal degradation of all blends led to two weight losses, for PLA and PP. The incorporation of PP improved the thermal stability of the blend. The effect of compatibilizer (ethylene-butyl acrylate-glycidyl methacrylate terpolymer, EBA-GMA) on the morphology and mechanical properties of 70/30 w/w PLA/PP blends was investigated. The tensile strength of these blends reached a maximum for 2.5 wt% EBA-GMA, and impact strength increased with increasing EBA-GMA content, suggesting that EBA-GMA is an effective compatibilizer for PLA/PP blends.     

Miscibility and properties of poly(l-lactic acid)/poly(butylene terephthalate) blends

Binary blends of poly(l-lactide) (PLLA) and poly(butylene terephthalate) (PBT) containing PLLA as major component were prepared by melt mixing. The two polymers are immiscible, but display compatibility, probably due to the establishment of interactions between the functional groups of the two polyesters upon melt mixing. Electron microscopy analysis revealed that in the blends containing up to 20% of poly(butylene terephthalate), PBT particles are finely dispersed within the PLLA matrix, with a good adhesion between the phases. The PLLA/PBT 60/40 blend presents a co-continuous multi-level morphology, where PLLA domains, containing dispersed PBT units, are embedded in a PBT matrix. The varied morphology affects the mechanical properties of the material, as the 60/40 blend displays a largely enhanced resistance to elongation, compared to the blends with lower PBT content.