Preparation of Anatase Hollow TiO2 Spheres and Their Photocatalytic Activity in the Photodegradation of Chlorpyrifos

Hollow anatase titania (TiO₂) spheres were synthesized using fructose and tetrabutyl titanate (Ti(OC₄H₉)₄, TBT) as the precursors via the conventional hard template method. The morphological, structural and thermal properties of the products were characterized using scanning electron microscopy (SEM), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), Fourier transform infrared (FTIR) spectroscopy, X‐ray diffraction (XRD), thermogravimetric and differential thermal analysis (TG‐DTA), Brunauer? Emmett? Teller (BET) surface area analysis and diffuse reflectance ultraviolet visible (DR UV? Vis) spectroscopy. XRD revealed that the hollow TiO₂ prepared was in the anatase phase and the BET surface area measured was about 22 m² g^?1. The photocatalytic activity of the synthesized hollow anatase TiO₂ in the photodecomposition of chlorpyrifos was 18.67 % higher than that obtained using commercial TiO₂.     

Thermal and hydrothermal stability of flame hydrolytically synthesized SiO2/TiO2 mixed oxides

The phase stability of the two TiO₂ modifications (anatase and rutile) in fumed SiO₂/TiO₂ nano-composites (0–24.8 wt-% silica) under thermal and hydrothermal conditions was investigated by X-ray powder diffraction, transmission electron microscopy (TEM) and gas adsorption methods (BET). The results show that the phase transformation from anatase to rutile type of structure and the growth of anatase crystallites are significantly retarded by mixing small amounts of SiO₂ into TiO₂, while the specific surface area is maintained. The SiO₂/TiO₂-composites reveal a remarkable shift in the anatase to rutile transformation temperature from approx. 500 °C (pure TiO₂) to approx. 1000 °C (samples with SiO₂ contents of more than 10%). The rate of phase transformation from anatase to rutile is enhanced under hydrothermal conditions compared to conventional thermal treatment, e.g. pure titania (AEROXIDE^® TiO₂ P25) annealed under hydrothermal conditions (100 g/m³ absolute humidity, 4 h at 600 °C) had a rutile content of 85%, while the same specimens annealed in absence of humidity contained only 46% rutile. However, the difference in rate of phase transformation became less pronounced when the silica content in SiO₂/TiO₂-composites was further increased.TEM results showed that the surface of the anatase crystallites was covered with silica. This averts coalescence of anatase crystallites and keeps them under a critical size during the annealing process. When the crystal domains grew larger, a rapid conversion to rutile took place. The critical size of anatase crystallites for the phase transformation was estimated to be 15–20 nm.     

Hydrothermal Synthesis and Characterization of Quasi‐1‐D Tungsten Disulfide Nanocrystal

Quasi‐1‐D (one‐dimensional) tungsten disulfide (WS₂) nanocrystal was synthesized through a two‐step hydrothermal process. Energy dispersive spectroscopy (EDS) identified that the chemical composition of the final product was WS₂. The produced nanocrystal was further characterized with X‐ray diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy (SEM). The results have shown that most of the products are quasi‐1‐D nanocrystals with the width around 140 nanometers and thickness about 30 nanometers. However, the length of the majority of nanocrystals could reach 1 micron. The selected area electron diffraction (SAED) pattern indicates that the nanocrystal is of a single crystal. N₂ adsorption measurement revealed that the BET specific surface area of this sample is 97 m²g^?1, which indicates that the as‐prepared product has better catalyzing and friction performance.     

Synthesis and photocatalytic activity of nanocrystalline TiO2 co-doped with nitrogen and cobalt(II)

Nitrogen-modified cobalt-doped TiO₂ materials were successfully prepared via a modified sol–gel method. The structure and properties of the catalysts were characterized via X-ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution TEM, ultraviolet–visible light diffuse reflectance spectra (UV–Vis DRS), N₂ adsorption–desorption isotherms, and energy-dispersive X-ray spectroscopy. The XRD patterns of the pure and co-doped TiO₂ samples indicate that the predominant phase was anatase. The average grain size obtained from TEM was approximately 10 nm. The Brunauer–Emmett–Teller analysis results indicate that the specific surface area was 77.7 m² g^?1. The UV–Vis DRS results for the co-doped sample reveal an absorption edge that had been red-shifted to 500 nm. The photocatalytic activities of the samples were evaluated through photodegradation of papermaking wastewater under UV and visible light irradiation. Compared with the cobalt-doped TiO₂ sample and Degussa P25, the 3 mol% N-doped mesoporous N/Co-TiO₂ photocatalyst exhibited the highest photocatalytic activity, which can be ascribed to the synergistic effect of the N and Co co-doping.     

Preparation and characterization of nanosized TiO2 powder as an inorganic adsorbent for aqueous radionuclide Co(II) ions

In this research TiO₂ sample was synthesized by a simple sol–gel method and was characterized by X-ray diffraction (XRD), Transmission electron microscopy (TEM) and Brunauer–Emmett–Teller (BET) techniques. The XRD result indicated that the obtained product was anatase titanium dioxide with high purity, the TEM image clearly showed that the particle sizes of TiO₂ nanoparticles were in the range of 30–70 nm, and the measured BET surface area of the heated TiO₂ nanoparticles was 147.14 m²/g. In this work, the prepared TiO₂ sample was used as a new adsorbent for the adsorption of radionuclide Co(II) ions from aqueous solutions, and the influence of pH, contact time, ionic strength and temperature in the presence or absence of humic acid/fulvic acid (HA/FA) were also investigated. The experimental results indicated that the adsorption of Co(II) ions onto TiO₂ was strongly pH-dependent. Based on the surface complexation, the presence of HSs enhanced the adsorption of Co(II) ions and the influence of Co(II) adsorption onto FA–TiO₂ hybrids was much stronger than that of HA–TiO₂ at pH values of 2.0–9.0. Adsorption of Co(II) ions onto TiO₂ powder was strongly dependent on ionic strength. The adsorption process mainly occured in the first contact time of 2 h and could be fitted by a pseudo-second-order rate model. The calculated thermodynamic data indicated that the adsorption of Co(II) ions onto TiO₂ was a spontaneous process and favorable at high temperatures.     

Solar active nano-TiO2 for mineralization of Reactive Red 120 and Trypan Blue: 1st Nano Update

Nano-TiO₂ was synthesized by sol–gel method. The catalyst was characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) images, transmission electron microscope (TEM), BET surface area measurement and DRS analysis. The formation of anatase phase nano-TiO₂ was confirmed by XRD measurements and its crystalline size is found to be 15.2 nm. SEM images depict the crystalline nature of prepared TiO₂. The BET surface area of prepared TiO₂ is found to be 86.5 m² g^?1 which is higher than that of commercially available TiO₂–P25. The photocatalytic activity of prepared anatase phase TiO₂ has been tested for the degradation of two azo dyes: Reactive Red 120 (RR 120) and Trypan Blue (TB) using solar light. The photocatalytic activity of nano-TiO₂ is higher than TiO₂–P25 under solar light. The mineralization of dyes has been confirmed by chemical oxygen demand (COD) measurements.     

Microstructure of SiO<Subscript>2</Subscript>/TiO<Subscript>2</Subscript> hybrid electrospun nanofibers and their application in dye degradation

SiO₂/TiO₂ hybrid nanofibers were prepared by electrospinning and applied for photocatalytic degradation of methylene blue (MB). The phase structure, specific surface area, and surface morphologies of the SiO₂/TiO₂ hybrid nanofibers were characterized through thermogravimetry (TG), X-ray diffraction (XRD) analysis, Brunauer–Emmett–Teller (BET) analysis, scanning electron microscopy (SEM), etc. XRD measurements indicated that doping of silica into TiO₂ nanofibers can delay the phase transition from anatase to rutile and decrease the grain size. SEM and BET characterization proved that silica doping can remarkably enhance the porosity of the SiO₂/TiO₂ hybrid nanofibers. The MB adsorption capacity and photocatalytic activity of the SiO₂/TiO₂ hybrid nanofibers were distinguished experimentally. It was found that, although increased silica doping content could enhance the MB adsorption capacity, the intrinsic photocatalytic activity gradually dropped. The SiO₂ (10 %)/TiO₂ composite nanofibers exhibited the highest MB degradation rate, being superior to SiO₂ (20 %)/TiO₂ or pure TiO₂.     

Rapid Synthesis of Mesoporous TiO2 for the Photoanodes in Dye Sensitized Solar Cells

Mesoporous TiO₂ microspheres with high specific surface areas were synthesized by means of a facile one‐step microwave hydrothermal process without using any template. The mesoporous materials were rapidly achieved using TiCl₄, urea and ammonium sulphate at comparatively low microwave power (400 W) for 8 min irradiation. The morphology and microstructure of the as‐prepared products were characterized by field emission scanning electron microscopy (FESEM), X‐ray diffraction (XRD), transmission electron microscopy (TEM) and Brunauer‐Emmett‐Teller (BET) surface area analysis. Structural characterization indicates that the TiO₂ microspheres display mesoporous structure. The average pore sizes and BET surface areas of the spheres were 5.3 nm and 222 m²g^?1, respectively. The mesoporous nanocrystals synthesized at 160 °C for 8 min were then used to prepare the photoanode for dye sensitized solar cells (DSSCs). A high power conversion efficiency of 5.72% was achieved from the mesoporous TiO₂ based photoanode, representing about 25.7% improvement over the efficiency of P25 photoanode.     

Preparation of large-area dye-sensitized solar cells based on hydrothermally synthesized nitrogen-doped TiO2 powders

Low-cost, yellowish, nanocrystalline nitrogen-doped titanium dioxide (N-doped TiO₂) powder was synthesized by a hydrothermal method. The as-prepared N-doped TiO₂ powder was characterized by X-ray diffraction, transmission electron microscopy (TEM), UV–Vis absorption spectra, X-ray photoelectron spectroscopy (XPS), and Brunauer–Emmett–Teller analysis techniques. The grain size of the prepared powder was around 13 nm as estimated by both Scherrer’s method and TEM images. The effect of the ratio of N-doped TiO₂ particles to Degussa P25 on the photovoltaic performance of large-area dye-sensitized solar cells (DSSCs) was also investigated. The N-doped TiO₂ electrode showed higher photovoltaic performance compared with that of pure P25 at constant irradiation of 100 mW cm^?2, which is attributed to the large pore size and high surface area of N-doped TiO₂ resulting in the introduction of extra charge carrier pathways that could be beneficial for overall charge transportation. Energy conversion efficiency of 5.12 % was achieved in a DSSC device with active area of 51.19 cm².     

Transition from anatase to rutile phase in titanium dioxide (TiO2) nanoparticles synthesized by complexing sol–gel process: effect of kind of complexing agent and calcinating temperature

In this work, the structural and optical properties of titanium dioxide (TiO₂) nanopowders are studied. The TiO₂ nanoparticles were synthesized by complexing sol–gel process and effect of complexing agents on transition of the anatase phase to rutile phase during the heat treatment have been investigated. In addition, we have studied the grain size of TiO₂ powders and their dependence on the type of complexing agent. The analysis of the XRD patterns, FT-IR and UV–Vis spectroscopy, BET surface area and TEM images show that the synthesis of nanoparticles with acetyl acetone (AcAc) as complexing agent yielded the smallest size of nanoparticles about 22–35 nm. Our results indicate that with increasing the calcinating temperature, the size of the nanoparticles is increased and the energy gap reduced, too. Also, the optical band gap was obtained in the range of 3.4–4.1 and 3.06–3.74 eV for anatase and rutile phases, respectively.     

锌离子掺杂的二氧化钛介孔空心微球的制备及光催化性能

以二氧化硅为模板,钛酸四丁酯(TBOT)为钛源,硝酸锌为锌源,采用溶胶凝胶法制备了锌离子掺杂的介孔二氧化钛空心微球。采用X射线衍射(XRD)、比表面积(BET)、透射电镜(TEM)、扫描电镜(SEM)和X射线光电子能谱(XPS)等技术对样品进行表征,以亚甲基蓝(MB)的光催化降解为目标反应评价其光催化活性。结果表明,去核之后的复合微球为空心微球,壁厚为20 nm左右。钛酸四丁酯溶液的滴加时间对微球的形貌影响较大,当滴加时间大于15 min时,可以得到结构清晰的空心微球。用氢氧化钠溶液去除二氧化硅核,反应90 min,二氧化硅可以被完全去除。X射线衍射表明,实验得到的掺杂锌离子的空心微球和没有掺杂锌离子的空心微球都是锐钛矿。当锌离子的摩尔分数为0.3%时,二氧化钛空心微球的晶粒尺寸最小,比表面积最大,催化亚甲基蓝降解的效率最高。     

Effects of NH 4 + and Cl− on the preparation of nanocrystalline TiO2 by hydrothermal method

Nanocrystalline TiO₂ powders with different morphologies and grain sizes were successfully synthesized by the hydrothermal method. Different concentrations of hydrochloric acid (HCl), ammonium chloride (NH₄Cl), ammonium sulfate [(NH₄)₂SO₄], and ammonium carbonate [(NH₄)₂CO₃] were used as additives in the hydrothermal process to investigate the effect of the concentration of ammonium (NH ₄ ⁺ ) and chloride ions (Cl^?) on the phase compositions, morphologies, and grain sizes of the prepared TiO₂. The as-synthesized samples were characterized by X-ray diffraction (XRD), transmission electron microscopy, Brunauer–Emmett–Teller analysis, and UV–Vis spectra. XRD results show that the as-synthesized powders are composed of anatase or a mixture of anatase and brookite. The grain size of the synthesized nano-TiO₂ powder ranged from 5.0 to 11.3 nm, and the related BET specific surface area varied from 127.5 to 191.0 m²/g. The photocatalytic activities of the prepared TiO₂ powders were evaluated by degradation of methylene blue (MB) in aqueous solution under UV light irradiation, and the results show that the photocatalytic performance of TiO₂ powders synthesized with additives is improved compared with that of TiO₂ prepared without any additives.     

Plasma-Assisted Synthesis of TiO2 Nanorods by Gliding Arc Discharge Processing at Atmospheric Pressure for Photocatalytic Applications

The present study explores a new method of synthesis of TiO₂ nano-particles in an aqueous medium from TiCl₃ precursor by non-thermal plasma in humid air as feeding gas obtained at atmospheric pressure. The precursor solution, TiCl₃ is oxidized by strongly reactive species generated by gliding arc plasma (HO^· = 2.85 V/SHE) to produce titanium oxide powders. The synthesized powder was characterised by X-ray powder diffraction, scanning electron microscopy, transmission electron microscopy, FTIR spectroscopy, nitrogen physisorption, and UV–Vis spectroscopy. The results obtained showed that the material consists of rod-shaped nanoparticles of rutile and anatase phases. The presence of TiO₂ phases was confirmed by FTIR spectrum and textural analyses showed that the material is mesoporous with specific surface area of 158 m² g^?1. UV–Visible spectrum of the plasma-synthesized TiO₂ sample showed that it absorbs in the UV–A region leading to effective use as a photocatalyst under visible light.     

High temperature stability and photocatalytic activity of nanocrystalline anatase powders with Zr and Si co-dopants

TiO₂ nanopowders doped by Si and Zr were prepared by sol–gel method. The effects of Si and Zr doping on the structural, optical, and photo-catalytic properties of titania nanopowders have been studied by X-ray diffraction (XRD), scanning electron microscopy, transmission electron microscopy, and UV–Vis absorption spectroscopy. XRD results suggest that adding impurities has a significant effect on anatase phase stability, crystallinity, and particle size of TiO₂. Titania rutile phase formation in ternary system (Ti–Si–Zr) was inhibited by Zr⁴⁺ and Si⁴⁺ co-doped TiO₂ in high temperatures (500–900 °C) and 36 mol% anatase composition is retained even after calcination at 1,000 °C. The photocatalyst activity was evaluated by photocatalytic degradation kinetics of aqueous methylen orange under visible radiation. The results show that the photocatalytic activity of the 20 %Si and 15 %Zr co-doped TiO₂ nanopowders have a larger degradation efficiency than pure TiO₂ under visible light.     

Evaluation of in vitro bioactivity and MG63 Oesteoblast cell response for TiO2 coated magnesium alloys

The present investigation reports TiO₂ coating on magnesium alloy AZ31 by sol–gel method via dip coating technique. TiO₂ coated surface was characterized by thin film X-ray diffraction (TF-XRD), Fourier transform infrared red (FT-IR) spectroscopy, scanning electron microscopy (SEM) with energy-dispersive X-ray (EDX) spectroscopy, atomic force microscopy (AFM) and transmission electron microscopy (TEM) techniques. From TF-XRD results, the peaks at 2θ values of 25.14, 32.12, 68.73 and 70.11 confirm the presence of TiO₂. The TiO₂ is crystalline in nature and the crystallite size is about 32.4 nm. SEM-EDX, TEM and AFM show that the coated surface is uniform and nanoporous. FT-IR analysis shows that the peak in the range of 692 cm^?1 is assigned to Ti–O–Ti stretching vibration. Contact angle measurements show that the coating is hydrophilic in nature. Bioactivity of the coating in simulated body fluid (SBF) was also examined, the hydroxyl functionalized surface greatly enhances the hydroxyapatite growth. The potentiodynamic polarization studies prove that the corrosion resistance of the TiO₂ coated surface after immersion in SBF for 7 days is improved dramatically. Cell adhesion studies confirm the increased cell attachment on TiO₂ coated surface when compared to uncoated alloy, due to less amount of Mg ion release from the substrate in the culture medium.     

Mesoporous titania photocatalyst: effect of relative humidity and aging on the preparation of mesoporous titania and on its photocatalytic activity performance

Mesoporous TiO₂ has been synthesized by the sol–gel method, using a nonionic triblock copolymer P123 as surfactant template under acidic conditions. The as-prepared samples were characterized by thermogravimetry–differential thermal analysis (TG–DTA), nitrogen absorption–desorption (BET), field emission scanning electron microscopy, and transmission electron microscopy. The photocatalytic activity of the mesoporous TiO₂ was evaluated by degradation of methylene blue under high-intensity UV light irradiation; the amount of methylene blue was measured by UV–visible spectroscopy. TG–DTA analysis revealed that the surfactant had been removed partly in as-synthesized samples. BET analysis proved that all the samples retained mesoporosity with a narrow pore-size distribution (4.5–6.3 nm) and high surface area (103–200 m²/g). All calcined mesoporous TiO₂ had high photocatalytic activity in the photodegradation of methylene blue.     

Sol–gel synthesis of macroporous TiO2 from ionic precursors via phase separation route

Monolithic macroporous titanium dioxide (TiO₂) derived from ionic precursors has been successfully prepared via the sol–gel route accompanied by phase separation in the presence of formamide (FA) and poly(vinylpyrrolidone) (PVP). The addition of FA promotes the gelation, whereas PVP enhances the polymerization-induced phase separation. Appropriate choice of the starting compositions allows the production of cocontinuous macroporous TiO₂ monoliths in large dimensions, and controls the size of macropores. The resultant dried gel is amorphous, whereas anatase and rutile phases are precipitated at 500 and 900 °C respectively, without spoiling the macroporous morphology. Nitrogen adsorption–desorption measurements revealed that the dried gels exhibits mesostructure with a median pore size of about 3 nm and BET surface area of 228 m²/g, whereas 15 nm and 73 m²/g for the gels calcined at 600 °C.     

Photocatalytic Activity of Microwave Plasma-Synthesized TiO2 Nanopowder

Nanocrystalline TiO₂ was synthesized using the microwave plasma technique and characterized using X-ray diffraction, transmission electron microscopy, scanning electron microscopy, laser particle size analyzer, UV–vis spectroscopy and BET surface area analyzer. The synthesized TiO₂ powder crystallized in anatase phase and the crystallite sizes were in nanometers. The photocatalytic activity of the compound was determined and compared against the activity of the commercial Degussa P-25 TiO₂ catalyst. The degradation rates of the dyes were found to be higher over the synthesized TiO₂ as compared to that over commercial Degussa P-25 TiO₂.     

Chitosan-modified TiO<Subscript>2</Subscript> as photocatalyst for ethanol reforming under visible light

This work reports the reforming of bio-ethanol on chitosan–TiO₂ hybrid photocatalysts at ambient temperature. The influence of chitosan composition on the photocatalytic performance of chitosan–TiO₂ hybrid was studied. The hybrids were characterized by CHN elemental analysis, nitrogen adsorption–desorption isotherms, thermogravimetric analysis, diffuse reflectance spectroscopy, X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The results showed that the preparation variables used for the incorporation of chitosan on TiO₂ promoted changes in the morphology, superficial area, crystal size and porosity of the photocatalyst, affecting the band gap of this semiconductor and consequently the reactivity of the chitosan–TiO₂ hybrids. The catalysts were evaluated for hydrogen production from ethanol under visible light. It was demonstrated that the calcination temperature of 623 K and a chitosan content of 20% were the most appropriate preparation conditions and the resulting product displays a pore size of 1.9 nm, crystal size of 11.3 nm, BET area of 178 m² g^?1 and band gap of 2.92 eV. The calcination temperature of 623 K and incorporation of 20% of chitosan obtained the same results in the conversion rate of hydrogen in comparison to the pure TiO₂ P25.     

Low Temperature Solvent Evaporation-induced Crystallization Synthesis of Nanocrystalline TiO2 Photocatalyst

A novel and efficient methodology for obtaining highly active photocatalyst of bi-phase TiO2 with small particle size and high specific surface area was developed by solvent evaporation-in-duced crystallization (SEIC) method at low temperature. The prepared TiO2 powder was characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM) and BET surface areas. The photocatalyfic activity was evaluated by the photocatalyflc oxidation of acetone in air. The results showed that the photocatalytic activity of the TiO2 powder preDared by this method approached that of Degnssa P25. This may be atotributed to the fact that the predated TiO2 powder had larzer specific surface areas (265 m2. g- 1 ) and smaller crystallite size (about 5 nm), but relatively low crystallinity, as compared with Degussa P25.