Effects of the nanoassociation of hexadecyltrimethoxysilane precursors on the sol–gel process

Modifications to the refractive indices of meso-structured organic–inorganic films caused by variations in the mole fraction of precursors in ethanolic solutions were investigated. The refractive indices were dependent on the mole fraction of C₁₆TMS (hexadecyltrimethoxysilane) and of the C₁₆TMS/TMOS (tetramethoxysilane) (1/1) mixture in ethanol. The dependency was determined to be nonlinear, and the phenomenon was attributed to self-assembly caused by the long alkyl groups (C₁₆) on the C₁₆TMS. Changes in the maximum decreasing rate of d_n/d_x values [(d_n/d_x)_max—for d_n/d_x estimation, the curves from Fig. 1 were associated with a polynomial; using a dedicated program, d_n/d_x was calculated; maximum values of d_n/d_x were taken into account and were included in Table 1)] were used to distinguish the behavior of alcoholic precursor mixtures. In the case of using pyrene as a fluorescent probe, the ratio between two peaks from the pyrene emission spectra (I₁/I₃) strongly decreased as hydrophobic micro-surroundings formed due to the self-assembly process. The UV–VIS spectra of a cationic dye solution, R6G, was studied because dilute solutions of the dye in equilibrium form measurable ratios of dimers and monomers. The absorbance was modified as micro-surroundings with different polarities were formed. These three methods demonstrated that nano-structuration was present prior to the occurrence of the sol–gel process. The combination of C₁₆TMS with other alkyltrialkoxysilane precursors having hydrocarbon chain lengths between C₁ and C₈ provided further evidence for a nonlinear dependence of the refractive indice and fluorescence spectra of pyrene. The properties of the final hybrids obtained by the sol–gel process were significantly affected by the precursor hydrocarbon chain lengths. DSC, XRD and FTIR measurements were used to show the plasticizing phenomena of C₁₆ as other alkyltrialkoxysilanes (i.e., C₁–C₈) were added.

Effect of post-treatment (gel aging) on the properties of methyltrimethoxysilane based silica aerogels prepared by two-step sol–gel process

The properties of silica aerogels are highly dependent on the post-treatment steps like gel washing, gel aging and gel drying. The experimental results of the studies on one of the post-treatment steps i.e. gel aging effect on the physical and microstructural properties of methyltrimethoxysilane (MTMS) based silica aerogels, are reported. These hybrid aerogels were prepared by two step sol–gel process followed by supercritical drying. The molar ratio of MeOH/MTMS (M) was varied from 7 to 35 by keeping the H₂O/MTMS (W) molar ratio constant at 4. The as prepared alcogels of different molar ratios were aged from 0 to 5 days. It was observed that 2 days of gel aging period is the optimum gel aging period for good quality aerogels in terms of low density, less volume shrinkage and high porosity. The well tailored network matrix with low density (0.04 g/cm³), less volume shrinkage (4.5%), low thermal conductivity (0.05 W/mK) and high porosity (98.84 %) was obtained for 2 days of gel aging period of M = 35. Further, the gelation time varied from 8 to 1 h depending on the M values. The gelation time was being more for lesser M values. The aerogels were characterized by bulk density, porosity, volume shrinkage, thermal conductivity, Scanning Electron Microscopy and the Fourier Transform Infrared spectroscopy.     

Effects of diethanolamine on the evolution of silver/titanium dioxide sol–gel process

In order to clarify the effects of diethanolamine (DEA) in the silver (Ag)/titanium dioxide (TiO₂) sol–gel process, sols with and without DEA, and films derived from these sols were prepared. The samples were investigated by X-ray diffraction, transmission electron microscopy, electron diffraction and optical absorption spectra. The results showed that metallic Ag clusters were formed in the sol with DEA and was absent in the sol without DEA. This indicated that DEA worked not only as the stabilizer but also as the reduce agent in Ag/TiO₂ sol–gel process. After annealed, Ag metallic nanoparticles were generated in the films derived from both the sols with and without DEA. The particles in the films derived from the sol with DEA were smaller than those from the sol without DEA. This can be ascribed to the limitation of the growth of Ag cluster formed in the sol with DEA during heat treatment. Mechanisms for the formation of metallic Ag in the Ag/TiO₂ sols and films were discussed. The effects of DEA in the sols and films were studied in detail.     

Porous structure of polybenzoxazine-based organic aerogel prepared by sol–gel process and their carbon aerogels

New organic aerogels were successfully prepared from a new class of phenolic resins called polybenzoxazines synthesized via conventional thermal curing reaction of a benzoxazine monomer using xylene as a solvent. Without the need for using supercritical conditions to remove the solvent during the process, the carbon aerogels were obtained with a much shortened time. From two different concentrations of benzoxazine solution, 20 and 40 wt%, the resulting polybenzoxazine aerogels, having densities of 260 and 590 kg/m³, respectively, were obtained after the curing process. The subsequent carbon aerogels were prepared by the carbonization of polybenzoxazine aerogels. The corresponding carbon aerogels exhibited a microporous structure with pore diameters less than 2 nm, the densities of 300 and 830 kg/m³, and surface area of 384 and 391 m²/g, respectively. The texture of the carbon aerogels was denser than that of their organic aerogel precursor, as evidenced by scanning electron microscopy. The transformation of the polybenzoxazine aerogel to the carbon aerogel was clearly observed using fourier transform infrared spectroscopy.     

Influence of process parameters on the sol–gel synthesis of nano hydroxyapatite using various phosphorus precursors

Hydroxyapatite Ca₁₀(PO₄)₆(OH)₂ has attracted widespread interest from both orthopedic and dental fields due to its excellent biocompatibility and tissue bioactivity properties. Since nanophase materials can mimic the dimensions of constituent components of natural tissues, the implants developed from nanophase material could serve as a successful alternative. However, the defects of hydroxyapatite ceramics, mainly brittleness and low fracture toughness, have been overcome by the use of nanophase hydroxyapatite coatings on the implant surfaces that integrate the good mechanical properties of metals and the bioactivity of hydroxyapatite. In the present investigation, Sol?Cgel hydroxyapatite was prepared from two different phosphorus precursors such as triethyl phosphate and phosphorus pentoxide respectively with calcium nitrate tetrahydrate as a calcium precursor. The effects of pH and liquid P³¹ Nuclear Magnetic Resonance spectroscopy for the solution aged at different periods were investigated and the synthesized hydroxyapatite powder was characterized by Transmission electron microscopy, X-ray Powder Diffraction, Fourier transform infrared spectroscopy and thermal analysis respectively. In order to fully understand the bioactivity of the synthesized materials, they were coated on 316L Stainless Steel implant surface by spin coating method at the spin speed of 2,000 Revolutions per minute. The effect of nanoparticles on the surface of 316L Stainless Steel implant was studied by adhesive strength measurements. The corrosion resistance property of the hydroxyapatite coatings was evaluated by electrochemical impedance analysis. From the results, it was observed that the hydroxyapatite coatings obtained from different precursors have very high resistance to corrosion with higher adhesive strength.     

Characterization of sol–gel process in the Y–Ba–Cu–O acetate–tartrate system using IR spectroscopy

Systematic investigation of sol–gel process in the Y–Ba–Cu–O acetate–tartrate system was performed using IR spectroscopy. Different values of synthesis parameters (temperature and duration of inorganic polymerization reactions, evaporation temperature and evaporation time during gelation) were used, and significant influence in some cases on superconducting characteristics of the oxide ceramics of composition YBa₂Cu₄O₈ was observed. Characterization by IR spectroscopy and thermogravimetric analysis, revealed the difference of local homogeneity in the precursor gels prepared under different evaporation regimes during gelation process. In addition, the explanation of the possible hydrolysis and condensation reactions in the sol state has been suggested.     

Lactic acid based sol–gel process of Ag nanoparticles and crystalline phase control of Ni particles in aqueous sol–gel process

Nickel and silver particles were prepared by using sol–gel auto-combustion method under N₂ atmosphere where lactic acid was applied as chelating agent. The synthesis of nickel particles was carried out at various pH conditions (2–7), resulting in the face-centered-cubic or hexagonal-close-packed crystalline nickel phase. The morphology and structure of synthesized nickel particles and silver nanoparticles were characterized by X-ray diffraction, transmission electron microscope, energy dispersive X-Ray spectroscopy and differential scanning calorimetry-thermogravimetric analysis. The results show that the spherical Ag nanoparticles with diameters in the range of 18–27 nm and narrow size distribution can be obtained by this sol–gel process.     

Synthesis of tin oxide nanoparticles by sol–gel process: effect of solvents on the optical properties

Tin oxide (SnO₂) nanoparticles were synthesized by the reaction of SnCl₄·5H₂O in methanol, ethanol and water via sol–gel method. The samples were characterized by X-ray diffraction (XRD), Fourier transform infrared, Scanning electron microscopy and Transmission electron microscopy. The optical properties of the as-prepared samples were investigated. The XRD analysis showed well crystallized tetragonal SnO₂ can be obtained and the crystal sizes were 3.9, 4.5 and 5 nm for the sample calcined at 400 °C for 2 h. It was found that solvents played important roles in the particle size effect of nanocrystalline SnO₂.     

Synthesis and physical properties of TEOS-based silica aerogels prepared by two step (acid–base) sol–gel process

The experimental results on the synthesis and physical properties of tetraethoxysilane- (TEOS) based silica aerogels produced by two step (acid–base) sol–gel process, are reported. The oxalic acid (A) and NH₄OH (B) concentrations were varied from 0 to 0.1 M and from 0.4 to 3 M, respectively. Monolithic and transparent aerogels have been obtained for the values of A=0.001 M and B=1 M. The effect of time interval (t) before the base catalyst (NH₄OH) addition to the acidic sol was studied from 0 to 72 h. The time interval at t=24 h of NH₄OH addition was found to be the best, in terms of low volume shrinkage, high optical transmission and monolithicity. The molar ratio of EtOH/TEOS (S) was varied from 3 to 7.5. Monolithic and transparent aerogels were obtained for an S value of 6.9. Also, the effects of molar ratio of acidic water, i.e., H₂O/TEOS (W₁) and basic water, i.e., H₂O/TEOS (W₂) on the physical properties of the aerogels have been studied. Highly transparent (∼90%) and monolithic aerogels with lower volume shrinkage (<10%) were obtained for the molar ratio 1:6.9:3.5:2.2 of TEOS:EtOH:acidic (H₂O):basic (H₂O). The results are discussed by taking into consideration the hydrolysis and polycondensation reactions. The aerogels were characterized by scanning electron microscopy (SEM), optical transmission, bulk density, volume shrinkage and porosity measurements.     

How to design cell-based biosensors using the sol–gel process

Inorganic gels formed using the sol–gel process are promising hosts for the encapsulation of living organisms and the design of cell-based biosensors. However, the possibility to use the biological activity of entrapped cells as a biological signal requires a good understanding and careful control of the chemical and physical conditions in which the organisms are placed before, during, and after gel formation, and their impact on cell viability. Moreover, it is important to examine the possible transduction methods that are compatible with sol–gel encapsulated cells. Through an updated presentation of the current knowledge in this field and based on selected examples, this review shows how it has been possible to convert a chemical technology initially developed for the glass industry into a biotechnological tool, with current limitations and promising specificities.     

Use of polyethylene glycol in the process of sol–gel encapsulation of Burkholderia cepacia lipase

Lipases from Burkholderia cepacia were encapsulated using polyethylene glycol (PEG, M _w 1500) at various concentrations (0.5–3.0 %, w/v) as an additive during the sol–gel immobilisation process. Matrixes immobilized in the presence and absences of additives were characterized by thermal analysis [thermogravimetric (TG) and differential scanning calorimetry (DSC)], scanning electron microscopy (SEM), enzymatic activity, and total activity recovery yield (Ya). The addition of PEG increased the activity values, with Ya just above 1.0 % (w/v) in the presence of PEG. The additional of 1.0 % (w/v) PEG increased enzyme activity from 33.98 to 89.91 U g^?1 and the values of recovery yield were 43.0–91.4 %, compared to values of the samples without PEG. PEG enhanced the thermal stability of the matrix structure in the temperature range 50–200 °C, as confirmed by TG and DSC analyses. This was influenced by the presence of water bound to the matrix. The SEM micrographs clearly showed an increase in the number of deposits on the material surface, producing matrices with greater porosity.     

Synthesis of MCM-48 from silatrane via sol–gel process

High-quality cubic MCM-48 is successfully synthesized using a new silica source known as silatrane and cetyltrimethylammonium bromide (CTAB) as the structure-directing agent via sol–gel process. The effects of synthesis parameters, viz. crystallization temperature, crystallization time, surfactant concentration, quantity of NaOH, and silica source, on the product structure are investigated. The synthesized samples are characterized using X-ray diffractometer (XRD), N₂ adsorption–desorption isotherms, and electron microscopy. Optimally, this product is synthesized from samples crystallized at 140°C for 16 h with a CTAB/SiO₂ ratio of 0.3 and NaOH/SiO₂ ratio of 0.5. The XRD result exhibits a well-resolved pattern, corresponding to the Ia3d space group of MCM-48. The BET surface area of this product is as high as 1,300 m²/g with a narrow pore-size distribution of 2.86 nm. The scanning electron microscopic (SEM) images also show the truncated octahedral shape and well-ordered pore system of MCM-48 particles.     

Silica covered porphyrin microstructures obtained in sol–gel processes

In this article, we report on the formation of well-defined highly emissive silica-covered porphyrin microstructures in base-catalyzed sol–gel processes. The microstructures were obtained by self-assembly of 5,10,15,20-tetrakis(4-hydroxyphenyl)porphyrin (mTHPP) at room temperature. Tetraethoxysilane (TEOS) was used as a silica precursor. The hybrid mTHPP- silica particles were characterized by means of reflectance UV–Vis and microscopy techniques including atomic force microscopy, scanning electron microscopy (SEM) and confocal fluorescence microscopy (CM). The SEM and TEM observations revealed that depending on the porphyrin concentration used in the synthesis, the shape of the hybrid mTHPP-silica particles has changed from ribbon-like (c _mTHPP = 2.09 mM) to rhombus-like structures (c _mTHPP = 4.35 mM). The ribbons were straight-edged, uniform in width (1.2–1.8 μm) and height (350–400 nm), and variable in length (40–100 μm). The rhombs were 1–3.7 μm in height, 7–25 μm in length, and 3.5–15 μm in width, and the ratio of length to width was uniform and equal to ca. 1.8–2. UV–Vis absorption spectra indicated that the J-aggregates and H-aggregates formed in the systems with lower and higher porphyrin content, respectively. Formation of different type of porphyrin aggregates in both systems resulted in different emission spectra, as it was shown with CM.