Beaming of light and enhanced transmission via surface modes of photonic crystals

We report beaming and enhanced transmission of electromagnetic waves by use of surface corrugated photonic crystals. The modes of a finite-size photonic crystal composed of dielectric rods in free space have been analyzed by the plane-wave expansion method. We show the existence of surface propagating modes when the surface of the finite-size photonic crystal is corrugated. We theoretically and experimentally demonstrate that the transmission through photonic crystal waveguides can be substantially increased by the existence of surface propagating modes at the input surface. In addition, the power emitted from the photonic crystal waveguide is confined to a narrow angular region when an appropriate surface corrugation is added to the output surface of the photonic crystal.     

加工误差引入的薄型KDP晶体附加面形

针对惯性约束聚变（ICF）驱动装置中口径为400 mm400 mm薄型频率转换KDP晶体在45放置状态下产生的附加面形问题,采用有限元分析软件ANSYS,建立了以实测数据为基础的大口径薄型KDP晶体的应变模型和有加工误差的夹具模型,仿真分析了KDP晶体的加工误差和夹具的加工误差对KDP晶体附加面形的影响, 给出了KDP晶体附加面形变化的P-V值和RMS值。在此基础上,通过对KDP晶体的加工误差及夹具支撑表面不同类型和不同大小加工误差的分析和比较,得出:KDP晶体边缘的加工误差和夹具支撑表面的凹型加工误差是引起较大附加面形的原因之一,KDP晶体的加工误差也会导致其面形变化不均匀,而夹具支撑表面的凸型、波浪形加工误差和压条表面的随机加工误差对KDP晶体附加面形的影响相对较小,且支撑表面的随机加工误差引起的附加面形变化介于其他两者之间。     

无损伤超光滑LBO晶体表面抛光方法研究

传统的抛光LBO晶体的方法是选用金刚石抛光粉在沥青抛光盘上抛光。沥青盘易于变形不容易修整,金刚石粉特别硬容易损伤抛光晶体表面。抛光过程中,抛光盘和抛光粉的选择是非常重要的,直接影响到抛光效率和最终的表面质量。新的抛光LBO晶体的方法,其抛光过程是一个化学机械过程,抛光盘、抛光粉和抛光材料相互作用。选用两种抛光盘(培纶和聚氨酯盘),三种较软的抛光磨料(CeO2,Al2O3和SiO2胶体),并在LBO晶体的(001)面进行抛光实验。用原子力显微镜测量和分析了表面粗糙度。结果表明,使用聚氨酯盘和SiO2胶体能够获得无损伤超光滑的LBO晶体表面,其表面粗糙度的RMS为0.3nm。     

单晶金刚石边缘表面倾斜角度对同质外延生长的影响

利用微波等离子体化学气相沉积法,对单晶金刚石(100)晶面边缘进行精细切割抛光处理,形成偏离(100)晶面不同角度的倾斜面,在CH_4/H_2反应气体中进行同质外延生长,研究单晶金刚石边缘不同角度倾斜面对边缘金刚石外延生长的影响.实验结果表明,边缘倾斜面角度对边缘的单晶外延生长质量有影响,随着单晶金刚石边缘倾斜面角度的增大,边缘多晶金刚石数量先减少后增多,在倾斜角3.8°时边缘呈现完整的单晶外延生长特性.分析认为,边缘不同角度的倾斜面会改变周围电场强度和等离子体密度,导致到达衬底表面的含碳前驱物发生改变,倾斜面台阶表面的含碳前驱物浓度低于能形成层状台阶生长的临界浓度是减弱单晶金刚石生长过程中边缘效应的主要原因.     

菁染料J-聚集体的微观结构研究

用原子力显微镜观察了阴阳离子菁染料及对应的阴离子菁染料和阳离子菁染料吸附在立方体(100)和八面体(111)溴碘化银乳剂颗粒表面形成的J-聚集体的微观结构,得到了3种不同排列的J-聚集体结构。研究结果表明,菁染料分子在溴碘化银颗粒表面不是单层吸附,而是以一定的形状聚集在溴碘化银表面。阴阳离子菁染料形成的J-聚集体为"鱼骨"状;阴离子菁染料的J-聚集体以"卡片堆积"式排列;阳离子菁染料J-聚集体为"磁砖"式结构。     

单轴晶体的光程差和Lyot型滤光器的视场

 建立了以光线入射方向和晶体光轴方向为基准的入射坐标系，利用波法线反曲面方程和电磁场在晶体折射界面处切向分量连续性的边界条件，得到了晶体中波法线方向、射线方向、波法线折射率和射线折射率的表达式。从非常光的射线方向和射线折射率出发，得到了在任意的晶体光轴方向和入射角条件下，光通过单轴晶体后寻常光、非常光的光程差表达式。对Lyot型滤光单元的透射率和视场进行了计算分析后发现，滤光单元的透射率随光线入射角的变化呈现一定的周期性，视场随光轴倾角的增大而减小。得出了透射率和视场随光轴倾角(光轴与晶体表面的夹角)和光线入射角(光线在晶体表面的入射角)的变化规律。讨论了通过改变晶体倾角实现滤光器调谐和补偿晶体厚度加工误差等技术问题。     

The study of surface polaritons by transition radiation

An experimental method for the study of surface polaritons by the use of of transition radiation is proposed. It is found that the placement of a prism close to the surface of a crystal allows one to study the decaying surface modes that are excited by a geam of charged particles travelling perpendicular to the surface of the crystal. Analytic and numerical results for the energy radiated per unit solid angle per unit frequency interval by a single charged particle over its complete trajectory are presented for the phonon form of the dielectric onstant for the crystal GaP. It is found that the predicted effects should be observable experimentally.     

Surface structure of polyethylene crystals as revealed by surface decoration. II. Electron-microscopic detection of mobilizable surfaces

The paper is the first step in the application of the gold decoration technique described in Part I to the electron-microscopic study of the nature of the fold surface of polyethylene single crystals. It was observed that different areas of the same crystal layer display different decoration densities. It appears that this is due to residual solvent which is retained to different extents by different crystal portions. This assumption is substantiated by the salient observation that the initially slight decoration differences are much accentuated by deliberate flooding of the decorated crystals with a swelling agent. The inference is that the swelling liquid mobilizes some loose elements along the crystal surface, and, consequently, the differences within the same crystal reveal a variable crystal surface as regards surface looseness. With the new technique we are now able to describe and follow these phenomena as a function of the relevant variables. Within the confines of the present work it has already become apparent by this test that, from the usual commercial polymer, surfaces with least looseness are formed toward the end of the crystallization.     

电沉积铁层晶体结构变化的第一性原理计算

研究了以氯化亚铁为主盐的电镀铁工艺,通过扫描电子显微镜微观形貌分析,铁镀层具有均匀致密结构,铁晶体具有较小的尺寸。通过X射线衍射测试发现,铝基底对铁镀层具有明显的诱导作用,然而随着沉积时间的增加,铁镀层逐渐趋向于Fe（211）晶面择优取向。采用第一性原理计算了不同晶面的表面能,铁晶体不同晶面的表面能依次为Fe（211）＜ Fe（110）＜Fe（200）,这很好地解释了Fe（211）晶面择优取向使体系的整体能量降低,有益于铁镀层的稳定性。     

基于对流传热模型的LD端面泵浦圆形激光晶体的热效应研究

通过对半导体端面泵浦棒状Nd∶YAG晶体的热效应进行了理论分析,研究了端面抽运圆形截面激光晶体内部温度场,建立了符合条件的激光晶体热模型。考虑晶体侧面与冷却液之间的对流传热,以及晶体端面与外界非绝热边界条件,从而建立更为合理的边界条件,得出更符合实际的晶体的温度分布场。研究结果表明,考虑端面的对流传热后,计算的晶体中心温度降低,而相应的热焦距稍有增加;空气传热系数增加时,晶体中心温度明显降低,热焦距显著增加,减弱了晶体热效应。     

A LEED and AES study of the structure,debye temperature,and oxidation of the (111) crystal face of thorium

The structure, and reactivity towards O₂ and CO, of the (111) crystal face of a single crystal of high purity thorium metal was studied using low-energy electron diffraction (LEED) and Auger electron spectroscopy (AES). After the sample was cleaned in vacuum by a combination of ion bombardment and annealing, a (1 × 1) LEED pattern characteristic of a (111) surface was obtained. Extended annealing of the cleaned sample at 1000 K produced a new LEED pattern characteristic of a (9 × 9) surface structure. A model of a reconstructed thorium surface is presented that generates the observed LEED pattern. When monolayer amounts of either O₂ or CO were adsorbed onto the crystal surface at 300 K, no ordered surface structures formed. Upon heating the sample following these exposures the (111) surface structure was restored accompanied by a reduction in the amount of surface carbon and oxygen. With continued exposure to either O₂ or CO and annealing, a new LEED pattern developed which was interpreted as resulting from the formation of thorium dioxide. Debye-Walter factor measurements were made by monitoring the intensity of a specularly reflected electron beam and indicated that the Debye temperature of the surface region is less than it is in bulk thorium. Consequently, the mean displacement of thorium atoms from their equilibrium positions was found to increase at the surface of the crystal. The presence of chemisorbed oxygen on the crystal surface affected the Debye temperature, raising it significantly.     

表面润湿法合成β沸石体系中晶种作用的研究

系统研究了表面润湿法合成β沸石的体系中,干晶种、润湿态晶种、异晶晶种(Y沸石、ZSM 5沸石)以及碱处理β沸石晶种在此晶化体系中的作用.采用β沸石产品及异晶作晶种时,可使产品的相对结晶度稍有提高,但对沸石微晶核的结构导向作用不明显.经浓碱液处理20min后的β沸石产品(碱处理晶种)作晶种引入晶化体系后,可以显著提高产品的相对结晶度,降低模板剂的用量,缩短晶化诱导期,成为表面润湿法合成β沸石体系的有效晶种形式.     

Enhancement of CsLiB(6)O(10) surface-damage resistance by improved crystallinity and ion-beam etching

The surface laser-induced damage threshold (LIDT) of CsLiB(6)O(10) (CLBO) crystal was enhanced twofold with improved crystallinity and ion-beam etching. For crystals with high crystal quality (bulk LIDT, 15.0-19.0 GW/cm(2)), the surface LIDT was 1.4-fold higher than for those with conventional crystal quality (bulk LIDT, 9.0-12.0 GW/cm(2)). In addition, removal of residual surface-polishing compounds by means of ion-beam etching can further enhance the surface LIDT by another 1.5-fold. Thus, CLBO crystals with high crystal quality and ion-beam etching are now more reliable for high-power UV light generation.     

双晶单色器弧矢聚焦晶体面形有限元分析

简要介绍了弧矢聚焦双晶单色器的基本原理、聚焦晶体的压弯以及鞍形形变的抑制,提出了柔性铰链弧矢聚焦晶体压弯机构,对弧矢聚焦晶体衍射面的子午形变和弧矢弯曲面形进行了有限元分析;用光学追踪程序SHADOW得出了弧矢聚焦晶体衍射面面形对单色器的光通量和分辨率的影响。     

二维云母界面对晶体定向生长的诱导作用研究

利用原子力显微镜(AFM)研究了云母衬底对氯化钠晶体定向生长的诱导作用,发现云母表面的氯化钠按照夹角60°左右的方向或者相互平行、相互垂直的方向生长,此角度分布规律与文献中生物分子在云母表面诱导下组装的纳米结构的夹角相互一致。说明云母表面不但可以用于诱导生物分子按照一定的方向进行自组装,还可以用于诱导无机晶体按照特定的方向进行组装生长。     

An x-ray photoelectron-spectroscopy study of Naβ-alumina surfaces

The cleavage-face of a sodim-β-alumina crystal was studied by means of X-ray photoelectron spectroscopy (XPS). A detailed quantitative analysis, which took into account the particular layered structure in this crystal, revealed a significantly (≈50%) Na deficient surface produced by cleaving the crystal along a conduction plane. The expressions derived for the elemental composition are applicable to any layered structure. Ion sputtering of the cleavage surface caused atom mixing in the layered structure as well as a preferential removal of the mobile sodium ions. Auger electron spectroscopy (AES) measurements showed that unlike the cleavage surface, the edge surface contains a significantly high concentration of sodium.     

The effect of bulk impurities on localized surface states

The effect of the occurrence of bulk impurities in a crystal on the existence and localization of surface states is examined by investigating a simple one-dimensional model. It is found that the bulk impurity has a small effect on the existence conditions for localized states associated with the surface, but the degree of localization of the corresponding charge density can be altered appreciably by the presence of such impurities. The penetration depth associated with localized surface levels can be much greater that than estimated for a pure crystal. The charge density associated with the electrons which occupy localized surface states may vary in a real crystal over a broader region near the surface than would be deduced from models of pure crystals. This will affect physical quantities, such as surface impedance, which are dependent on this charge distribution.     

各向异性表面张力对定向凝固中深胞晶生长的影响

利用匹配渐近展开法和多变量展开法求出定向凝固深胞晶生长的浓度场和界面形态的全局渐近解,研究各向异性表面张力对定向凝固深胞晶生长的影响.结果表明,各向异性表面张力对定向凝固过程深胞晶生长有显著的影响.随着各向异性表面张力增大,胞晶前端部分浓度减小而胞晶界面收缩;胞晶根部的浓度增大而界面曲率增大或根部的曲率半径减小,各向异性表面张力使得深胞晶界面振幅增加.本文结果能够计算定向凝固过程中深胞晶生长的浓度、界面形态.     

Photobleaching on Photonic Crystal Enhanced Fluorescence Surfaces

The effect of resonant fluorescent enhancement from a photonic crystal surface upon the fluorescent photobleaching rate of Cyanine-5 labeled protein has been investigated. We show that the enhanced excitation mechanism for photonic crystal enhanced fluorescence, in which the device surface resonantly couples light from an excitation laser, accelerates photobleaching in proportion to the coupling efficiency of the laser to the photonic crystal. We also show that the enhanced extraction mechanism, in which the photonic crystal directs emitted photons approximately normal to the surface, does not play a role in the rate of photobleaching. We show that the photobleaching rate of dye molecules on the photonic crystal surface is accelerated by 30x compared to an ordinary glass surface, but substantial signal gain is still evident, even after extended periods of continuous illumination at the resonant condition.     

LD端面泵浦矩形Nd:YVO_4晶体的热效应研究

建立了矩形激光晶体的热传导模型。通过充分考虑晶体侧面与冷却液之间的对流传热,以及晶体端面与外界的热传导,建立了更为合理的边界条件。利用有限元差分法求解泊松方程,得到激光晶体内温度和温度场分布。研究结果表明,在考虑晶体的侧面对流和端面导热的情况下,得出了更符合实际的晶体温度场分布,计算的热焦距与实验测量结果更为吻合。