Measurement of the Elasticity of Biological Soft Tissue of Finite Thickness

Elasticity is of profound significance to evaluating the function of a biological soft tissue.When the elasticity of a tissue is macroscopically changed,it means that the biological function of the tissue is abnormal and some disease or injury may occur.In the present work,an elastometer is developed to measure the elasticity of biological soft tissues.The measurement is based on the indentation method and the force is measured by the bending of the cantilever.The force-indentation data of the soft tissue is experimentally measured by this elastometer and Young's modulus of the tissue is calculated using the Hertz-Sneddon model.For comparison,a numerical model for the indentation method is established using the finite element method.The difference between the actual modulus and the measured modulus is discussed.The effect of the thickness of the specimen on the measurement is investigated.Young's moduli of beef,porcine liver and porcine kidney are experimentally measured.The results indicate that our elastometer is effective in measuring Young's modulus of a soft tissue quantitatively.     

混合物物态方程的计算

 在采用体积相加原理计算混合物物态方程的基础上,建立了一种物理模型确定混合物温度。根据混合物中各组分温度和压强平衡条件,采用压强-密度迭代方法计算给出混合物物态方程,编制了两种组分的混合物物态方程计算程序。为检验建立的温度模型的合理性及程序的有效性,分析了不同密度、温度状态的氢（H2）和钨（W）组成的混合物状态参量,计算了以下情形及其组合情形的混合物物态方程：H₂和W以不同质量比混合;质量比固定,单组分状态不同;温度区间和密度区间不同。研究表明:实际应用中在建立的混合物温度模型基础上确定的混合物物态方程是合理的。     

Model of process of singular estimation of the primary tone of a speech signal

A novel method is proposed to estimate the primary tonal frequency of speech. The method is based on singular spectrum analysis. A singular model of a vocalized segment of a speech signal is presented that considers the direct and inverse problems. A study is conducted of the process of singular estimation of the primary tonal frequency of speech. Experimental research is carried out using a model that yields adequacy and reliability estimates. The concept of singular estimation of the primary tonal frequency of speech is introduced.     

Real-time measurement of retardation of eighth-wave plate independent of fast-axis direction

A real-time measurement method for the retardation of an eighth-wave plate is proposed. The collimated laser beam is split using a Glan Taylor polarizer with two side escape windows. The reflected sub-beam is detected using a detector, whereas the transmitted sub-beam passes through the quarter-wave plate and the eighth-wave plate of interest. Then, it is reflected by the mirror and passes reversely through the eighth-and quarter-wave plates. Finally, it is analyzed using the Glan Taylor polarizer and detected using another detector. With two detection signals, the retardation is resolved and found to be independent of the fast-axis direction, initial intensity, and circuit parameters. In the experiment, a crystal quartz sample is measured at different fast-axis angles. The standard deviation of the retardation is 0.9 o . The usefulness of the method is verified.     

混合物物态方程的计算

在采用体积相加原理计算混合物物态方程的基础上,建立了一种物理模型确定混合物温度。根据混合物中各组分温度和压强平衡条件,采用压强-密度迭代方法计算给出混合物物态方程,编制了两种组分的混合物物态方程计算程序。为检验建立的温度模型的合理性及程序的有效性,分析了不同密度、温度状态的氢（H2）和钨（W）组成的混合物状态参量,计算了以下情形及其组合情形的混合物物态方程：H2和W以不同质量比混合;质量比固定,单组分状态不同;温度区间和密度区间不同。研究表明:实际应用中在建立的混合物温度模型基础上确定的混合物物态方程是合理的。     

Investigation of oscillations of a soliton of a bose condensate of atoms in a trap in the limit of small oscillations of its walls

The motion of the center of a soliton in a trap with oscillating walls is studied analytically and numerically for the case in which the intrinsic frequency of small soliton oscillations in the equilibrium state considerably exceeds the frequency of wall oscillations. this problem can be solved either by applying the gross–pitaevskii equation, which most exactly describes the behavior of the soliton in the trap, or by using the approximate, “mechanical,” equation of motion of the newtonian type for the center of the soliton. an approximate analytical solution of the mechanical equation is obtained and is compared with the numerical solution of the newton equation, while the latter solution is compared with the numerical solution of the gross–pitaevskii equation. good agreement between the first two solutions is revealed. it is also shown that there is a range of parameters in which the numerical solutions of the newton and gross–pitaevskii equations are closest to each other. the frequency-sweeping effect of soliton center oscillations is revealed. an approximate analytical formula for the limiting frequency of these oscillations is obtained and the numerical analysis of this phenomenon is performed.     

大尺度相干结构的光学特性研究

根据大气近地面层对流湍池的实验结果,提出了一种用于描述大尺度相干结构的立体模型——椭球结构模型。计算并分析了该大尺度相干结构对光传输波前相位结构函数的影响,且和小尺度湍流结构作了比较。对于相同的参数,光线平行于间断面时造成的影响大于垂直于间断面;一般情况下,影响都很小;但当光线平行穿过具有三角波模型结构的间断面时可能产生较大的影响。     

类胡萝卜素的分子光谱研究

类胡萝卜素是含有9个CC共轭双键的短链多烯类生物分子. 特殊的分子结构, 使其不仅在光采集, 光防护, 防癌, 抗癌等生物学领域有重要应用, 而且在分子导线, 光开关, 滤光器等光电器件研制中也有重要的非生物学应用. 本文对它的分子光谱进行研究和总结, 结果表明, 类胡萝卜素具有宽带荧光, 将其用于荧光增强受激拉曼散射可以获得宽带受激拉曼散射; 电子能隙随温度降低而收缩, 电子吸收光谱红移, 这特性使它能研制优质半导体元件; 极大的拉曼活性和三阶非线性系数, CC键基频拉曼散射截面可以比普通分子大10个数量级, 和频、倍频拉曼散射强度也很高, 低温下与基频强度比可达0.5. 类胡萝卜素分子的这些光谱特性对多烯类分子结构、性能研究及其在非生物学中的应用有重要参数价值.     

液晶磁致旋光的研究

利用矩阵方法分析了液晶的旋光效应，导出了液晶旋光的矩阵表示. 利用JG-3型连续可调谐磁场仪搭建实验装置，红外1350 nm激光器做光源，测量了偏振光通过磁场作用下BL-009型向列相液晶的旋光角，详细分析了磁场对液晶旋光性能的影响. 通过实验测试，对液晶的阈值磁场强度进行了讨论，同时对实验结果进行了理论上的分析，得出了液晶旋光角随磁场与液晶盒表面夹角而变化的结论，验证了液晶分子轴的旋转方向与磁场的方向无关，这为更好的研究液晶的特性以及液晶器件的设计具有重要的参考价值. 关键词： 液晶 矩阵 磁致旋光     

冷却储存环主环磁铁的准直测量

采用激光跟踪仪及配套带软件Insight对兰州重离子加速器冷却储存环主环磁铁进行了安装和准直。首先建立全局坐标系，用来确定从源体到实验环各子系统的理论原点的位置；而各个子系统又分别以各自的理论原点为基础建立局部坐标系，用来安装定位本系统内的各个元件；对各个子系统中的每一个元件还采用了元件坐标系。准直测量时，先在每块磁铁上焊接8个测量基准；然后对磁铁上的基准进行测量，以确定其在元件坐标系中的位置；再架设激光跟踪仪，测量主环控制网点，恢复主环局部坐标系，根据元件在主环局部坐标系中的位置及理论坐标，计算出相关的变换参数；转入元件坐标系，采用激光跟踪仪及Insight 软件显示实时测量坐标及其与理论值之差，其精度达到0.15 mm。     

粉末颗粒气力加注特性实验研究

粉末发动机是以粉末颗粒为燃料的新型发动机,具有多次起动和推力调节的功能.粉末加注是粉末发动机实验组织过程中的重要环节.本研究通过搭建粉末供应系统开展粉末气力加注实验,研究对比了集粉箱加注位置、流化气量对粉末气力加注特性的影响.考虑了供粉过程中储箱内粉末堆积密度的动态变化,并建立了相应的计算方法,同时还采用控制系统理论揭示了储箱内粉末堆积密度的变化规律.结果表明:在相同条件下,较大的流化气量有利于加注过程稳定,但集粉箱加注率较低;气力加注方式下集粉箱内的粉末堆积密度大于储箱内初始堆积密度;采用较小的流化气量与集粉箱壁面切向加注方式有利于提高粉末粒径分布均匀性;集粉箱壁面切向加注方式下,流化气量较小时储箱内粉末的堆积密度是先增大后减小,且堆积密度最终值小于初始值,而流化气量较大时,储箱内粉末的堆积密度是先增大后减小再增大后减小,且堆积密度最终值大于初始值;储箱内粉末堆积密度的动态变化过程类似于欠阻尼二阶系统,流化气量较小时系统阻尼系数较小,而流化气量较大时系统阻尼系数较大,且是一个变阻尼过程.     

Theory of scattering of X-Rays

Scattering by bound electrons is considered in the nonrelativistic approximation. The matrix element for the transition is calculated in the second order of perturbation theory without the use of intermediate states. It is shown that ordinary scattering is accompanied by scattering giving lower -energy quanta and fast electrons.     

余弦二值编码纯相位全息图的数字微镜器件显示

分析了采用错误减算法的迭代过程,在已知物波函数傅里叶谱的振幅和物波函数振幅的情况下恢复出纯相位的物波函数,最大限度地保留物波的振幅及相位信息.提出采用余弦二值编码生成二值全息图,即全息图的透射率函数取0或1.二值全息图通过数字微镜器件全息显示系统进行了重构显示,重构效果很好.理论分析了数字微镜器件的衍射效率,表明其最大衍射效率仅和微镜之间的间隔尺寸与微镜边长之比有关.余弦二值编码方法从理论上消除了零级衍射,可以制作像素较多的全息图.     

负损耗因子的成因分析

本文根据双耦合系统的经典统计能量平衡方程分析了利用该方程进行SEA参数测量中产生负损耗因子的可能性;通过对双非保守耦合线性振子的振动分析,从理论上分析了负损耗因子形成的条件。结果证明:非保守强耦合是产生负损耗因子的必要条件;而测量频率带宽内不同时包含两振子的固有频率或两振子的参数存在较大差异是产生负损耗因子的充分条件。负损耗因子的绝对值随耦合参数的增大而增大。     

无偏振效应分束器反射相移对法拉第镜式光学电流互感器输出光偏振态的影响

线性双折射和反射相移使光学电流互感器输出光偏振态产生椭圆退化并导致灵敏度降低,法拉第镜式光学电流互感器可以有效解决椭圆退化问题。无偏振效应分束器是构成该方案的核心器件,为了准确掌握无偏振效应分束器的性能和作用,用琼斯矩阵建立了无偏振效应分束器和法拉第镜式光学电流互感器的矩阵模型。分析了无偏振效应分束器反射相移对系统输出光偏振态的影响。提出无偏振效应分束器反射相移的测量方案并测出其常温下的实际值为5.02°,绘制了温度实验曲线。用MathCAD软件仿真了系统输出光偏振态图,并分析了椭率与无偏振效应分束器反射相移的关系。指出计量0.2级光学电流互感器所允许的反射相移漂移范围要小于0.1%。所得结果可为光学电流互感器的实用化研究提供参考。     

声速测量实验原理讨论

对空气中声速测量实验原理进行了讨论,考虑了空气对声波的吸收,分别用平面波和球面波表示发射探头和接收探头之间的声波,导出了接收声压的表达式,分析了声压随探头间距的变化规律.结果表明,尽管声场不是理想驻波,但声压极值随探头间距按半波长周期性的变化规律与驻波共振原理得到的结论相一致,然而3种原理在解释接收声压幅值衰减规律时存在差异,其中球面波原理与实验现象最吻合.     

Comparative analysis of side-illumination methods of measurement of emission decay of fluorescent polymer fibers

The fluorescence decay constant of a fluorescent polymer optical fiber is measured by two different side illumination methods. Comparative analysis of these methods is performed. It is shown that the difference in the measured parameters is caused by different conditions of energy exchange between the core, cladding, and radiation modes of the fiber waveguide.     

马赫-曾德尔干涉仪消光比和单通道光开关

对马赫-曾德尔(M—Z)干涉仪的滤光消光比特性进行了研究，提出了一种在其一端加上光纤全反镜的方法，大大改善了马赫一曾德尔干涉仪的输出谱特性，由此提出并设计了一种单通道光开关，实验得到了约37．4dB的开关动态范围。     

Dependence of the characteristics of bubbles on types of sonochemical reactors

Computer simulations of bubble oscillations in liquid water irradiated by an ultrasonic wave have revealed that the characteristic of bubbles depends on types of sonochemical reactors: a horn-type reactor and a standing-wave type reactor. When the acoustic amplitude is large at 20 kHz, the bubble content is mostly water vapor even at the end of the bubble collapse and the temperature inside a bubble at the collapse is relatively low. On the other hand, when the acoustic amplitude is relatively low, the bubble content is mostly noncondensable gas at the end of the bubble collapse and the bubble temperature is relatively high. In a horn-type sonochemical reactor, the former type of bubbles are dominant because many bubbles exist near the horn-tip where the acoustic amplitude is large, while in a standing-wave type reactor the latter type of bubbles are dominant because the Bjerknes force gathers bubbles at a region where acoustic amplitude is relatively low.     

Measures of wettability of solid surfaces

The surface tension of a solid surface is not amenable to direct experimental measurement. The most common method for assessing this surface tension is by contact angle measurements. The currently optimal way to measure and interpret contact angles is discussed, emphasizing the yet unresolved issues. It is argued that the most meaningful measurements to be done are of the most stable apparent contact angle (from which the surface tension of the solid is eventually assessed) and the contact angle hysteresis range (which indicates the existence and degree of chemical heterogeneities and roughness).