Proton mobility in the solid inorganic hydrates of acids and acid salts

The method for the calculation of the proton-transfer frequency (n_t) and its activation energies (E_t) was suggested. Results of the calculations were presented. The experimental data on the activation energy of proton-containing group rotation and protonconductivity values for some hydrates of inorganic acids and acid salts were compared with the calculated ones.     

Good correlation between the calculated gas-phase first proton macroaffinities of some triazacycloalkanes ([X]aneN3, X = 9–12) with their protonation constants in solution

A theoretical study on first protonation step of a series of triazacycloalkanes with general formula {([X]aneN₃, X = 9–12)} (X = 9, L222; X = 10, L223; X = 11, L233; X = 12, L333) is reported. The geometry of all ligands and their monoprotonated forms were fully optimized at both the Hartree–Fock and DFT (B3LYP) levels of theory using 6-31+G* basis set. Then the first proton macroaffinities were calculated from the proton microaffinities according to defined equations. It is shown that there are good correlations between the calculated gas-phase first proton macroaffinities of these ligands with their protonation constants in solution.     

含有不同功能基团的丙烯酸长链酯共聚物在溶液中的相互作用研究(Ⅰ)

合成了分别具有质子给体和质子受体官能团的丙烯酸正辛酯共聚物。由于在给体和受体聚合物上分别引入的羧酸基团（AA）和碱性基团（VP）,在溶液中进行共混复合时存在彼此间的相互作用而使共混体系表现出较高的比浓粘度。引入比浓粘度增长因子R,讨论了共混组分和溶剂体系等因素对聚合物分子链间相互作用的影响。结果表明,质子给体聚合物（PDP）和质子受体聚合物（PAP）的相互作用强度及等化学复合比与组分聚合物的分子链组成和溶剂性质有关。     

P(VDF-co-TrFE-co-CTFE)-g-SPS共聚物的合成表征

采用商业聚(偏氟乙烯-co-三氟氯乙烯)(P(VDF-co-CTFE)为原料,结合氢化反应、ATRP和磺化反应系统合成了一系列聚(偏氟乙烯-co-三氟乙烯-co-三氟氯乙烯)-g-磺化聚苯乙烯(P(VDF-co-TrFE-co-CTFE)-g-SPS)共聚物.重点研究了测试环境(如温度和相对湿度)、聚合物微观结构(接枝密度,接枝长度等)对聚合物形貌、吸水率和质子传导率的影响.研究表明,在接枝量相同的情况下,随着接枝密度的降低,聚合物的相分离更加明显,亲水相从孤岛型逐渐转变为部分连续型;聚合物的吸水率随磺酸基摩尔含量增加而提高;聚合物的质子传导率随着温度的提高和湿度的降低而降低;在较低温度下,聚合物的电导率随接枝密度的增加而降低,而在较高温度下,聚合物的电导率随接枝密度的增加而升高.组成优化的P(VDF-co-TrFE-co-CTFE)-g-SPS共聚物在30～120℃和高湿度条件下,其质子传导率明显优于Nafion112膜.     

Synthesis of fluoro-containing sulfonated poly(phthalazinone ether ketone ketone)s and their properties as PEM in PEMFC and DMFC

A series of sulfonated poly(ether ketone ketone)s (SPPFEKKs) containing both of phthalazinone and hexafluoroisopropylidene moieties were synthesized by direct nucleophilic polycondensation reaction from 4-(4-hydroxyphenyl)-1(2H)-phthalazinone (DHPZ), 4,4-hexafluoroisopropylidene-diphenol (BPAF), 1,4-bi(4-fluorobenzoyl) benzene (DFKK) and 1,4-bi(3-sodium sulfonate-4-fluorobenzoyl) benzene (SDFKK). The obtained SPPFEKKs had high molecular weight with inherent viscosity ranged from 1.29 to 1.53 dL/g and their chemical structure was characterized by FT-IR and ¹H NMR. The ionic membranes of SPPFEKKs showed high proton conductivity, for instance, SPPFEKK-120 (DS = 1.20) demonstrated 1.0 × 10⁻¹ S/cm proton conductivity at 95 °C, which was very close to that of Nafion^®117. All the SPPFEKK membranes exhibited methanol permeability lower than 2.76 × 10⁻⁷ cm²/s, which was much lower than that of Nafion^®117 (2.38 × 10⁻⁶ cm²/s). These copolymers also showed excellent thermal stability and good solubility in aprotic polar organic solvents. The ionic membranes of SPPFEKK demonstrated tensile strength varied from 57 to 69 MPa depending on their DS.     

新型聚苯并咪唑树脂的微波合成及质子交换膜的性能

采用微波合成法, 调整己二酸和2,6-吡啶二甲酸2种二酸单体的配比, 使其与联苯四胺进行三元共聚, 制备出一系列新型含脂肪链结构的聚苯并咪唑(PBI)类质子交换膜, 并用红外光谱、 热重分析进行了表征, 对膜的吸水率、 溶胀率、 质子传导率、 机械强度及抗氧化性能等进行了测试. 当己二酸与2,6-吡啶二甲酸的摩尔比为3: 2时, 所制备的PBI-C₂膜掺杂磷酸后在160℃下的质子传导率可达30 mS/cm, 拉伸强度在常温下可达77.54 MPa, 断裂伸长率为39.25%, 最大储能模量为9.0623 MPa, 最大损耗模量为8.36 MPa, 玻璃化转变温度为360℃, 芬顿试验192 h后膜的降解率仅为0.21%, 表明PBI-C₂膜在高温质子交换膜燃料电池中具有较好的应用前景.     

A study of linear versus angled rigid rod polymers for proton conducting membranes using sulfonated polyimides

Linear and angled monomers were incorporated into the main chain of a polyimide in order to investigate the effect of kinked versus linear polymers on membrane properties such as water uptake and proton conductivity. Polymers prepared using linear 4,4′-sulfonyldianiline, SPI1, and using angled 3,4′-sulfonyldianiline, SPI2, were cast into membranes possessing ion exchange capacities that varied from 0.79 to 2.75 meq g⁻¹. Membranes are thermally stable up to 300 °C under air. Proton conductivity of both membranes increases with temperature to values of 0.1-0.2 S cm⁻¹. The conductivity of angled, SPI2 membranes is greater than those prepared from SPI1 for a given IEC but water uptakes are lower. These differences are attributed to increased entanglements of the angled polymers, which limits the degree of swelling and increases the proton concentration. These results may be important in the design of proton conducting membranes from other rigid polyarylenes.     

Effect of chain compositions on interpolymer specific interaction in solutions

An interpolymer specific interaction of polymers with complementary proton donor units and proton acceptor units was studied with viscometry. In this study, poly(styrene-co-octyl acrylate-co-acrylic acid) as proton donating polymer (PDP) and poly(styrene-co-octyl acrylate-co-4-vinylpyridine) as proton accepting polymer (PAP) with different macromolecular chain compositions were prepared by emulsion copolymerization. Complexed solutions formed by PDP and PAP were studied with a novel interaction criterion k_a based on viscosity enhance factor. The effects of macromolecular chain compositions on the ability to interpolymer interaction and complex stoichiometry were discussed. The results showed that long chain alkyl acrylate units play an important role in the interpolymer specific interaction.     

A NOVEL KIND OF PROTON EXCHANGE MEMBRANE: CHARACTERS AND PROTON TRANSPORT MECHANISM

A novel proton exchange membrane(PEM) was designed and prepared from a polymer containing calix[4]arene as the functional unit to transport proton.The proton-conductivity of this membrane is about the same order of magnitude as that of Nation~(?) 112 membrane.It is of interest to note that very different from most of the currently known PEMs,this membrane can transport proton without the help of water or other solvents.It is deduced that the protons are transported via an ion tunneling model.This opens u...     

Proton dynamics in an extended array of hydrogen bonds: normal coordinates, proton transfer and macroscopic quantum entanglement in the ground state

After a brief introduction to neutron scattering techniques, illustrated with the scattering function for harmonic oscillators, some new aspects of proton dynamics in the KHCO₃ crystal are presented. The full scattering function for the proton modes measured on single crystals provides a graphic view of proton dynamics. Vibrational states are fully characterized with three quantum numbers. The effective oscillator mass of 1 amu confirms the decoupling of protons from the lattice. Combining infrared, Raman and inelastic neutron scattering techniques, the double minimum potential for the transfer of a single proton along hydrogen bonds is totally determined. Elastic neutron scattering techniques probe dynamics in the fully degenerate ground state. Quantum entanglement arising from normal coordinates gives rise to quantum interference. With diffraction techniques, the dynamical structure arising from large-scale quantum coherence is observed as ridges of intensity, well separated from Bragg's peaks. The vibrational wave function in the ground state must be regarded as a superposition of non-factorable macroscopic wave function.     

非含氟型磺化聚合物质子交换膜材料的研究进展(下)

概述了近十年来非含氟型磺化聚合物质子交换膜材料的研究进展,包括各种材料的制备和性质,详细地讨论了材料的化学结构、形态与其性能(质子导电率、耐水性、尺寸稳定性、吸水率、抗自由基氧化性、甲醇透过率等)之间的关系,其中结合作者在磺化聚酰亚胺方面的研究工作,重点对这类材料进行了系统、深入的介绍和讨论.最后,本文还对今后燃料电池用质子交换膜材料的研究提出了一些设想和展望.本文分为上下两篇,其中下篇主要综述了非含氟型磺化聚合物的性能与结构形态之间的关系.     

New proton conducting hybrid membranes for HT-PEMFC systems based on polysiloxanes and SO3H-functionalized mesoporous Si-MCM-41 particles

For increased efficiency of high-temperature polymer electrolyte membrane fuel cells (HT-PEMFC), new types of membranes have to be developed. This approach has been realized by preparing hybrid membranes containing SO₃H-functionalized mesoporous Si-MCM-41 as hydrophilic inorganic modifier in a polysiloxane matrix exhibiting sulfonic acid groups and basic heterocyclic groups like benzimidazole. The proton conductivity of sulfonated particles was modelled on the atomic scale in order to understand the influence of the density of sulfonic acid groups and of the presence of water molecules. The different hybrid membranes are characterized concerning their thermal stability, water uptake, and proton conductivity. Whereas the proton conductivity of well-established, but expensive and at >120 °C not long-time stable Nafion membranes continuously decreases with increasing temperature, the polysiloxane membranes, which suffer from a low-proton conductivity at around 100 °C, recover at about 120 °C due to intrinsic proton transport. At 180 °C the pure polysiloxane shows a proton conductivity which is only one order of magnitude lower than that of Nafion. Moreover, if the polysiloxane membrane contains additionally 10 wt.% of an SO₃H-modified Si-MCM-41, the proton conductivity of such hybrid membrane at temperatures >180 °C and low relative humidity <10% is higher than that of Nafion membranes by a factor of 10.     

非含氟型磺化聚合物质子交换膜材料的研究进展(上)

概述了近十年来非含氟型磺化聚合物质子交换膜材料的研究进展,包括各种材料的制备和性质,详细地讨论了材料的化学结构、形态与其性能(质子导电率、耐水性、尺寸稳定性、吸水率、抗自由基氧化性、甲醇透过率等)之间的关系,其中结合作者在磺化聚酰亚胺方面的研究工作,重点对这类材料进行了系统、深入的介绍和讨论.最后,本文还对今后燃料电池用质子交换膜材料的研究提出了一些设想和展望.本文分为上下两篇,其中上篇主要综述了各种非含氟型磺化聚合物的制备方法.     

侧链磺化聚芳醚质子交换膜的研究进展

燃料电池是以氢气、甲醇等作为燃料的一种新型能量转化装置,其中质子交换膜燃料电池（Proton Exchange Membrane Fuel Cell, PEMFC）凭借其能量功率高、启动速度快和使用寿命长等优点已经在移动电源、潜艇和电动汽车等领域得到了广泛应用。质子交换膜（Proton Exchange Membrane, PEM）对PEMFC的性能影响最大,高效的PEMFC需要PEM具有高的质子电导率、良好的热稳定性和机械性能、低燃料渗透率以及优异的物理化学稳定性等。目前市面上多数使用的均是具有优异质子电导率的Nafion系列膜,但其存在制备困难、成本昂贵、质子电导率严重依赖湿度等缺点,在一定程度上限制了其发展。为了让PEM有更多的选择,科学家一直专注于使用新材料替代Nafion膜。近年来,科学家们模拟Nafion结构,通过合成各种侧链含磺酸基团的聚芳醚结构,使得亲水基团磺酸基和疏水基团之间形成微相分离结构,从而获得了一系列具有优异综合性能的PEM。本文将重点对侧链烷基磺化型、侧链磺化嵌段型、侧链局部密集磺化型、侧链磺化交联型和侧链磺化复合型这几种常见策略的合成方法及性能进行了综述,最后展望了侧链磺化聚芳醚在PEM领域的优势及发展前景。     

磷酸掺杂的ab-PBI膜及其在高温质子交换膜燃料电池中的应用

以3,4-二氨基苯甲酸为单体合成了ab-聚苯并咪唑.研究了磷酸掺杂的该质子交换膜在80~200℃,不同湿度以及不同酸掺杂量下的质子电导率.该质子交换膜可作为燃料电池的膜电解质,在常压不增湿的条件下,可使电池运行温度达到200℃.     

A role of non-hydrogen framework vibrational modes in formation of ferroelectric properties of H-bonded K3H(SO4)2-like materials

An effect of molecular vibrational modes within the dimers [O₃AO–(H/D)OAO₃]³⁻ on behavior of H-bond protons or deuterons is studied theoretically for H-bonded antiferroelectrics and quantum paraelectrics of the M₃(H/D)(AO₄)₂ family (M=alkali metal, A=S, Se). The ‘heavy’ reorganization modes in D-species of this family and both reorganization and promoting modes in corresponding H-analogues are examined. It is shown that the analysis with due regard for the reorganization modes results in insignificant decreasing of the effective tunneling frequency of light nuclei. Hence the reasonable estimations of the critical temperature of the low-temperature phase transition in M₃D(AO₄)₂ materials are available only with additional corrections related to potential profiles of a deuteron. It is noted that in the limits of the proposed model the promoting mode in the case of H-species can favor, in principle, the increasing as well as the decreasing of effective proton level splitting.     

Substituent Effects on Phosphate-Catalyzed Proton Exchange in Amides

The kinetics of phosphate-catalyzed proton exchange have been measured with NMR lineshape analysis for a series of amides, ureas, and carbamates. A hypothetical energy profile for transition structures of concerted phosphate catalysis ?_c and of stepwise phosphate catalysis ?₁, ?₂ is used for discussion of the substituent effects. The concerted mechanism of phosphate catalysis operates only for amides RCONHCH₃ for which the electron-donating ability of the substituent R is comparable with, or better than, that of the methyl group. We conclude that concerted phosphate catalysis is inoperative in proteins or polypeptides.     

燃料电池质子交换膜用新型磺化聚芳醚酮的合成和性能表征

报道了一种新型磺化聚芳醚酮材料的合成方法, 通过引入取代基对聚芳醚主链进行保护，用氯磺酸直接磺化方法在聚芳醚酮高分子侧基上引入磺酸功能基, 实现了聚合物磺化结构的可控定位合成, 得到了稳定性较好的磺化聚芳醚酮. 通过核磁共振(NMR)、 热重(TG)和凝胶渗透色谱(GPC)等分析方法对其结构及性能进行了表征. 用溶液浇膜法制备了质子交换膜, 考察了膜的各种性能, 并与商用Nafion膜进行了比较, 其导电性、 热稳定性和吸水性远优于Nafion膜, 抗氧化性、抗水解性和机械强度也达到了较高的指标.