A molecularly imprinted polymer based on functionalized multiwalled carbon nanotubes for the electrochemical detection of parathion-methyl

A novel composite of vinyl group functionalized multiwalled carbon nanotubes (MWCNTs) molecularly imprinted polymer (MIP) was synthesized and applied as a molecular recognition element to construct an electrochemical sensor for parathion-methyl in this paper. The special molecular recognition properties of parathion-methyl mainly dominated by π-π, p-π interaction and hydrogen bonding formed among functional monomer, template and matrix. A series of electrochemical experiment results proved that the prepared material had good adsorption capacity and fast mass transfer rate to parathion-methyl. The good selectivity of the sensor allowed fine discrimination between parathion and paraoxon, which had similar structures to parathion-methyl. The response of the MIPs was linearly proportional to the concentration of parathion-methyl over the range of 2.0 × 10(-7) to 1.0 × 10(-5) mol L(-1) with a lower detection limit of 6.7 × 10(-8) mol L(-1) (S/N = 3). This sensor was also applied in the detection of parathion-methyl in pear and cucumber with average recoveries of between 94.9% and 106.2% (RSD < 5%) being obtained. The results mentioned above show that the novel electrochemical sensor is an ideal device for the real-time determination of parathion-methyl in real samples.     

Synthesis of a novel molecularly imprinted polymer based on functionalized multi-walled carbon nanotubes for selective extraction of sulfadiazine prior to spectrophotometric determination

A novel and efficient sulfadiazine imprinted polymer was synthesized via co-precipitation method and successfully grafted on magnetic multi-walled carbon nanotubes. The synthesized magnetic imprinted polymer was characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray powder diffraction analysis, thermal analysis and applied as a sorbent for selective magnetic solid-phase extraction of sulfadiazine. The retained sulfadiazine was eluted by 150.0 µL methanol/acetic acid (6:4) solution and quantified by fiber optic linear array spectrophotometry via formation of a detectable azo dye. All parameters affecting the extraction of sulfadiazine were investigated and optimized. Under the optimized conditions, the method exhibited a linear dynamic range of 2.0–50.0 µg L^?1 with a detection limit of 0.56 µg L^?1 and enrichment factor of 300.0. The relative standard deviation at 30.0 µg L^?1 of sulfadiazine (N = 6) was 2.8 and 4.6% for intra-day and inter-day, respectively. The method was successfully applied to determine sulfadiazine in human urine, honey, milk and environmental water samples.     

多壁碳纳米管表面L-组氨酸手性印迹聚合材料的制备及性能表征

通过酰胺化反应在多壁碳纳米管（MWNTs）表面接枝双键,以L-组氨酸（L-His）为模板,甲基丙烯酸（MAA）为功能单体,乙二醇二甲基丙烯酸酯（EGDMA）为交联剂,偶氮二异丁腈（AIBN）为引发剂,利用表面印迹技术,在MWNTs表面制备印迹聚合物（MWNTs-MIPs）．采用红外光谱,扫描电子显微镜和热重分析表征印迹聚合物的性质,结果表明MWNTs表面成功接枝了一层稳定的、厚度为35～40nm具有识别能力的印迹聚合材料．结合高效液相色谱技术,通过填充色谱柱在线色谱分析,探讨不同pH值的流动相下该印迹材料对L-His的分离行为,结果表明MWNTs—MIPs色谱柱在流动相pH=7．0时分离效果最好,能够选择性地识别L-His和D-His,分离度R为1．78,选择因子α为1．28．     

Sensitive and selective molecularly imprinted electrochemical sensor based on multi-walled carbon nanotubes for doxycycline hyclate determination

An electrochemical sensor for doxycycline hyclate(DC)detection with high sensitivity and good selectivity is reported.The sensor was fabricated by electro-polymerization of molecularly imprinted polymers(MIPs)in the presence of DC onto multi-walled carbon nanotubes modified glassy carbon electrode(MWCNTs/GCE).The MWCNTs can significantly increase the current response of the sensor,leading to enhanced sensitivity.The MIPs provide selective recognition sites for DC detection.The experimental parameters,such as the polymer monomer concentration,supporting electrolyte pH,the time for electro-polymerization and the incubation time of the sensor with DC were optimized.Under optimized experimental conditions,the sensor displayed a linear range of 0.05μmol/L-0.5μmol/L towards DC detection,with the detection limit of 1.3×10^-2μmol/L.The sensor was successfully applied for recovery test of DC in human serum samples.     

A molecularly imprinted polymer for the determination of neopterin

A molecularly imprinted polymer (MIP) for the specific retention of neopterin has been developed. A set of 6 polymers was prepared by radical polymerization under different experimental condition using methacrylic acid as functional monomer and ethylene glycol dimethacrylate as crosslinker, with the aim to understand their influence on the efficiency of the MIP. The performance of each MIP was tested in batch experiments via their binding capacity. The MIP prepared in the presence of nickel ions in dimethylsulfoxide-acetonitrile mixture (P4) exhibited the highest binding capacity for neopterin (260 μmol per gram of polymer). A selectivity study with two other pteridines demonstrated the polymer P4 also to possess the best selectivity.

A molecularly imprinted polymer for the specific retention of neopterin was developed. A set of 6 polymers was prepared under different experimental condition. The performance of each MIP was tested through their binding capacity. The MIP P4 prepared in the presence of nickel ions exhibited the highest binding capacity

     

A molecularly imprinted polymer for the determination of neopterin

A molecularly imprinted polymer (MIP) for the specific retention of neopterin has been developed. A set of 6 polymers was prepared by radical polymerization under different experimental condition using methacrylic acid as functional monomer and ethylene glycol dimethacrylate as crosslinker, with the aim to understand their influence on the efficiency of the MIP. The performance of each MIP was tested in batch experiments via their binding capacity. The MIP prepared in the presence of nickel ions in dimethylsulfoxide-acetonitrile mixture (P4) exhibited the highest binding capacity for neopterin (260 μmol per gram of polymer). A selectivity study with two other pteridines demonstrated the polymer P4 also to possess the best selectivity.

Preparation of magnetic molecularly imprinted polymer based on multiwalled carbon nanotubes for selective dispersive micro-solid phase extraction of fenitrothion followed by ion mobility spectrometry analysis

A novel molecularly imprinted polymer based on magnetic multiwalled carbon nanotubes was fabricated and applied for selective dispersive micro-solid phase extraction of fenitrothion prior its determination by ion mobility spectrometry. The composite was synthesized using magnetic multiwalled carbon nanotubes as the support. Methacrylic acid was used as the functional monomer, fenitrothion as the template, ethylene glycol dimethacrylate as the cross-linker, and 2,2-azoisobutyronitrile as the initiator. The resultant polymer was characterized by FTIR spectroscopy, X-ray diffraction, field emission scanning electron microscopy, Brunauer–Emmet–Teller analysis, thermogravimetric analysis, and vibrating sample magnetometer techniques. Experimental factors affecting the extraction efficiency such as pH and amount of sorbent were evaluated. Under optimum experimental conditions, the developed method displayed the linear range of 5–220 μg/L with a detection limit of 1.3 μg/L. The intra- and interday relative standard deviations for determination of fenitrothion were 3.6 and 4.7% (n = 6), respectively. Ultimately, the proposed method was used to monitor trace amounts of fenitrothion in fruits, vegetables, and water samples.     

Flow chemiluminescence sensor for determination of clenbuterol based on molecularly imprinted polymer

In this paper, a novel flow chemiluminescence (CL) clenbuterol sensor based on molecularly imprinted polymer (MIP) on line enrichment nanogram clenbuterol and chemiluminescence reaction of potassium permanganate and formaldehyde in the polyphosphate enhanced by clenbuterol. Clenbuterol in the urine was selectively adsorbed on the clenbuterol-imprinted polymer, which was packed into the flow cell. The formaldehyde and the polyphosphate with potassium permanganate flowed through the flow cell and reacted with the on line adsorbed clenbuterol and produced strong CL. The results show that the sensor was reversible. The CL intensity was linear with clenbuterol concentration from 1.0 × 10⁻⁹ g/mL to 5.0 × 10⁻⁸ g/mL. The detection limit was 3.0 × 10⁻¹⁰ g/mL. The R.S.D. for ng/mL clenbuterol was less than 5% (n = 3). The present method offered a high selectivity and sensitivity that made the quantitative analysis of trace clenbuterol (ng/mL) in the animal urine sample.     

基于分子印迹技术的敌百虫农药传感器的研制

监测环境、食物中的有机磷残留是一项非常重要的工作。目前,一般采测量,但是设备昂贵、色谱预处理复杂,用色谱法难以快速测量有机磷农药。分子印迹技术(molecular imprinting technique,MIT)是Wulf[f2-4]等发展起来的一项为获得空间结构和结合位点上与某一结构的化合物或化合反     

基于分子印迹聚合物的化学发光传感器测定尿样中的甲福明

合成了甲福明的分子印迹聚合物,以此聚合物为识别物质,在线分离富集甲福明,建立了一种测定甲福明的流动式化学发光但感器。N-溴代丁二酰亚胺(NBS)和荧光素与甲福明发生化学反应,产生强的化学发光。甲福明质量浓度在2×10-8~8×10-6g/mL范围内同发光强度成良好线性关系,方法的检出限为6×10-9g/mL,相对标准偏差小于5%(n=9)。选择性实验表明将分子印迹聚合物作为识别物质应用于化学发光分析中,能大大提高化学发光分析方法的选择性。该传感器可逆性强、稳定性好,可重复使用100次以上,已用于人体尿样中甲福明的测定。     

Evaluation of a novel microextraction technique for aqueous samples: porous membrane envelope filled with multiwalled carbon nanotubes coated with molecularly imprinted polymer

A novel microextraction technique based on membrane-protected multiwalled carbon nanotubes coated with molecularly imprinted polymer (MWCNTs-MIP) was developed. In this technique, MWCNTs-MIP were packed inside a polypropylene membrane envelope, which was then clamped onto a paper clip. For extraction, the packed membrane envelope was first impregnated with toluene and then placed in sample solutions. Target analytes in the solutions were first extracted into toluene in the membrane envelope, and were then extracted specifically onto the MWCNTs-MIP. After the extraction, target analytes were desorbed in methanol for liquid chromatography analysis. MWCNTs-MIP of prometryn were used as a model to demonstrate the feasibility of this novel microextraction technique. Factors affecting the extraction including organic solvent, stirring rate, extraction time, salt concentration, and pH were investigated. Under the optimized conditions, the limits of detection (a signal-to-noise ratio of 3) for the selected triazine herbicides were 0.08-0.38 μg/L. The prepared membrane envelope could be used at least 50 times. The developed method was used for the analysis of the triazines spiked in river water, wastewater, and liquid milk, with recoveries ranging from 79.3-97.4, 58.9-110.3 and 76.2-104.9%, respectively.     

Novel molecularly imprinted polymers based on multiwalled carbon nanotubes with bifunctional monomers for solid-phase extraction of rhein from the root of kiwi fruit

A novel molecularly imprinted polymers based on multiwalled carbon nanotubes synthesized by precipitate polymerization was applied as a selective sorbent for separation and determination of rhein (4,5-dihydroxyanthraquinone-2-carboxylic acid) from the root of kiwi fruit samples coupled with high performance liquid chromatography (HPLC). The molecularly imprinted polymers were prepared with methacrylic acid and 4-vinylpyridine as bifunctional monomers. The chemical structure of the molecularly imprinted polymers was characterized by Fourier transform infrared spectrometer. The equilibrium rebinding experiment and competitive adsorption experiment showed that these imprinted polymers exhibited good adsorption ability toward rhein. The Langmuir adsorption equilibrium constant, K(m) , and theoretical maximum adsorption capacity, Q(m) , were estimated to be 0.43 and 6.77 mg g(-1) , respectively. Compared with molecularly imprinted polymers prepared with methacrylic acid or 4-vinylpyridine solely, the molecularly imprinted polymers synthesized with bifunctional monomers showed enhanced molecular imprinting effect and higher adsorption capacity for the template rhein. The performances of the molecularly imprinted polymers utilized as solid phase extraction sorbent were investigated in detail. The molecularly imprinted polymers prepared by the method proposed in this work could successfully apply to extraction and determination of rhein from the root of kiwi fruit samples coupled with HPLC.     

A chemometrics approach for simultaneous determination of cyanazine and propazine based on a carbon paste electrode modified by a molecularly imprinted polymer

In a completely rational and designed approach, simultaneous determination of cyanazine and propazine in environmental and food samples was performed using a molecularly imprinted polymer modified carbon paste electrode (MIP-CPE) and partial least squares. The MIP-CPE designed is based on the theoretical studies functioned as a selective recognition element and pre-concentrator agent for cyanazine and propazine. Fractional factorial and central composite designs were performed to recognize, and subsequently optimize, the variables affecting the cathodic stripping voltammetric currents for the analytes. The important variables were identified to be accumulation potential with optimum values of -0.45 and -0.44 V and pH with optimum values of 2.40 and 2.34 for cyanazine and propazine, respectively. Exploration of the overall optimum conditions for simultaneous determination of cyanazine and propazine resulted in accumulation potential of -0.44 V and pH of 2.4. Dynamic linear ranges of 0.05-9.00 μmol L(-1) and 0.01-1.00 μmol L(-1) and detection limits of 0.010 and 0.001 μmol L(-1) were obtained for cyanazine and propazine, respectively. The results of the application of the proposed method on the simultaneous determination of cyanazine and propazine in foodstuffs and environmental samples were satisfactory.     

Sputtering deposition of Pt nanoparticles on vertically aligned multiwalled carbon nanotubes for sensing L-cysteine

A highly sensitive electrochemical sensor for determination of L-cysteine (CySH) is presented. It is based on vertically aligned multiwalled carbon nanotubes modified with Pt nanoparticles by magnetron sputtering deposition. The morphology of the nanocomposite was characterized by scanning electron microscopy, transmission electron microscopy and energy-dispersive. The electrochemistry of CySH was investigated by cyclic voltammetry, differential pulse voltammetry and chronoamperometry. The mechanism for the electrochemical reaction of CySH at the modified electrode at different pH values is discussed. The electrode exhibits a higher electrocatalytic activity towards the oxidation of CySH than comparable other electrodes. It displays a linear dependence (R ²?=?0.9980) on the concentration of CySH in the range between 1 and 500 μM and at an applied potential of +0.45 V, a remarkably low detection limit of 0.5 μM (S/N?=?3), and an outstandingly high sensitivity of 1.42?×?10³ μA?mM^?1?cm^?2, which is the highest value ever reported. The electrode also is highly inert towards other amino acids, creatinine and urea. The sensor was applied to the determination of CySH in urine with satisfactory recovery, thus demonstrating its potential for practical applications.

Potentiometric propranolol-selective sensor based on molecularly imprinted polymer

A novel potentiometric sensor based on molecularly imprinted polymer (MIP) for propranolol, an adrenergic-blocking drug, was designed. The influence of molecularly imprinted polymer particle content and sodium tetraphenylborate additives in polyvinylchloride membrane was shown. The electrodes show near-Nernstian responses down to 10^?4–10^?5?M propranolol concentration. The potentiometric response of MIP-based sensor for propranolol in mixed nonaqueous medium was shown at first. Sensor selectivity relative to various inorganic cations, atenolol and metoprolol, was reported. Direct potentiometry was used to determine propranolol in aqueous modeling solutions and pharmaceutical preparations with good results.     

Flow-injection chemiluminescence sensor for determination of isoniazid in urine sample based on molecularly imprinted polymer

In this paper, molecularly imprinted polymer (MIP) of isoniazid is synthesized through thermal radical copolymerization of metharylic acid (MAA) and ethylene glycol dimethacrylate (EGDMA) in the presence of isoniazid template molecules. A novel flow injection chemiluminescence sensor for isoniazid determination is developed by packing the isoniazid-MIP into the flow cell as recognition elements. Isoniazid could be selectively adsorbed by the MIPs and the adsorbed isoniazid was sensed by its great enhancing effect on the weak CL reaction between luminol and periodate which were mixed in the flow cell. The enhanced CL intensity is linear in the range 2x10(-9) to 2x10(-7) g/mL and the detection limit is 7x10(-10) g/mL (3sigma) isoniazid with a relative standard deviation 2.8% (n=9) for 8x10(-8) g/mL. The sensor is reversible and reusable. It has a great improvement in sensitivity and selectivity for CL analysis. As a result, the sensor has been successfully applied to determination of isoniazid in human urine. At the same time, the binding characteristic of the polymer to isoniazid was evaluated by batch method and the dynamic method, respectively.     

Nanogram/mL detection of nortriptyline: Preparation of a molecularly imprinted polymer for spectrophotometric determination of nortriptyline based on multivariate optimization methods

In this work, the molecularly imprinted polymer was used as a selective sorbent in solid‐phase extraction method for the spectrophotometric determination of nortriptyline at 239 nm. Molecularly imprinted polymer was synthesized by pyrrole as a functional monomer in the presence of nortriptyline as a template. Several factors, consist of the concentration of the monomer to template ratio, amount of initiator, stirring rate, reaction time, the pH of the buffer solution, amount of sorbent, loading time, shaking rate of loading, extraction time, and shaking rate of extraction were evaluated due to their effectiveness in the preparation and extraction capability of molecularly imprinted polymer. Multivariate optimization methods, such as Plackett‐Burman and central composite designs, were employed to find and optimize the significant factors. Under the selected optimal conditions, molecularly imprinted polymer showed a linear range from 0.1 to 100 µmol/L (0.026 to 26 µg/mL) nortriptyline, a detection limit of 10.3 nmol/L (2.7 ng/mL), a highly repeatable (relative standard deviation of 3.7%) and reproducible response (relative standard deviation of 4.6%), and a good selectivity in the presence of structurally related molecules. Furthermore, molecularly imprinted polymer showed high extraction efficiency and was successfully used for the determination of nortriptyline in real samples.     

Chemiluminescence determination of metformin based on hydroxyl radical reaction and molecularly imprinted polymer on-line enrichment

A novel and simple chemiluminescence (CL) method has been developed and validated for determination of metformin. This method is based on hydroxyl radical chemiluminescence—the hydroxyl radical generated by reaction of Cu(II) and hydrogen peroxide oxidizes rhodamine B (RhB) to produce weak CL which can be enhanced by metformin. At the same time, metformin molecularly imprinted polymer (MIP) was synthesized. After enrichment based on the selectivity of metformin-MIP, the CL method was successfully applied to the determination of metformin in human serum. The linear range was from 1.0×10⁻⁸ to 1.0×10⁻⁶ g mL⁻¹ and the detection limit was 4×10⁻⁹ g mL⁻¹. The relative standard deviation at 2.0×10⁻⁷ g mL⁻¹ by use of MIP was 3.67% (n=7).     

Electrochemical dipyridamole sensor based on molecularly imprinted polymer on electrode modified with Fe3O4@Au/amine-multi-walled carbon nanotubes

Journal of Solid State Electrochemistry - A novel molecularly imprinted electrochemical sensor based on Fe3O4@Au nanoparticles immobilized on amine-multi-walled carbon nanotubes by the strong...