镧对Cu_6Sn_5长大驱动力及焊点可靠性的影响

在Sn60 Pb40钎料合金中加入微量稀土元素镧可以抑制表面组装焊点界面处Cu6 Sn5金属间化合物的生长 ,进而使焊点热疲劳寿命提高两倍。基于扩散动力学的热力学计算结果表明 ,添加微量稀土元素镧可降低Cu6 Sn5金属间化合物的长大驱动力 ,但存在一个镧的有效局部摩尔分数范围 ,0 18%是其极限值 ,0 0 8%是其最佳值。     

添加0.1%Ce对Sn-3.0Ag-0.5Cu焊料与铜基板间的金属间化合物的影响

研究了Sn-3.0Ag-0.5Cu-xCe（x=0,0.1%）焊料合金与Cu基板250℃钎焊及170℃恒温时效时对基体和界面金属间化合物（IMC）的形成与长大行为的影响。结果发现,在Sn-3.0Ag-0.5Cu焊料中添加0.1?后,能够抑制基体和钎焊界面反应及随后时效过程中IMC的形成与生长。焊点最初的界面IMC为Cu6Sn5,时效5 d之后,该两钎焊体系中均发现了Cu3Sn薄层的生成,且随着时效时间的增加,各IMC层厚度有明显的增加趋势。与Sn-3.0Ag-0.5Cu/Cu焊点相比,Sn-3.0Ag-0.5Cu-0.1Ce/Cu钎焊体系焊点界面处的IMC层更为平整和细薄。时效过程中,界面IMC的形成与长大受扩散机制控制。     

镧、铈对铝铜合金凝固过程及凝固组织的影响

本文用热分析对比法和金相法研究了微量镧、铈对Al-5wt％Cu合金的凝固过程和凝固组织的影响规律。发现微量镧、铈能改变该合金的凝固参数,增大其过冷度和明显细化组织,微量镧、铈改变了Al-5wt％Cu合金的凝固过程,使其在α相析出之后共晶析出之前有一中间相析出。加微量铈可形成Al_8Cu_4Ce。理论分析认为,Le_2O_3、Ce_2O_3、La(OH)_3和Ce(OH),可做为α相的异质核心。     

Al_(66)Mn_9Ti_(25) La金属间化合物的变形行为与机制

研究了微量稀土元素La对Al6 6 Mn9Ti2 5 金属间化合物显微组织、变形行为、裂纹生成的影响。在Al6 6 Mn9Ti2 5 金属间化合物中添加微量La ,保持L12 结构 ,晶格常数基本无变化 ,促进了晶粒枝晶化和第二相弥散化 ,起到一定的抑制微裂纹生成和扩展以及沿晶开裂的作用 ;同时 ,还可增强位错的可动性 ,使压缩塑性得到改善。探讨了La改善变形行为的机制。     

铈对SnAgCu钎料的显微组织和性能影响

采用扫描电镜和能谱分析等测量方法,研究了微量铈对SnAgCu无铅钎料的润湿性、焊点抗拉强度、热疲劳性能和微观组织的影响.研究结果表明,添加微量的铈后,钎料的铺展面积明显增加,焊点抗拉强度得到明显提高,焊点热疲劳特性也得到很大的改善,但过量的铈会明显恶化钎料的此类性能.对AnAgCu-XCe焊点内部组织进行分析,发现微量铈可以明显细化焊点内部组织,降低金属问化合物层的厚度.     

稀土元素在含残余砷、锡09Cr2AlMoRE钢中的作用

对加稀土前后09Cr2AlMoRE钢取样分析化学成分,制备金相样用SEM-EDS研究了钢中析出物特征,制备透射电镜(TEM)试样通过TEM研究元素的晶界偏聚,并用热力学计算了稀土Ce,La,S和残余元素As反应固定残余元素As的可能性。研究结果表明:在低氧、硫的条件下,稀土镧可以和09Cr2AlMoRE钢中较低含量的砷(130×10-6)作用生成镧砷金属间化合物;铈、镧主要是通过形成稀土砷硫夹杂物固定钢中残余元素砷。另外,在本实验条件下稀土元素(64×10-6)只有很微量的偏聚在晶界,残余元素As不在晶界偏聚。     

Al-5Mg-Er合金中Al3Er相的析出及其热力学计算分析

通过应用Miedema热力学模型方法对添加了微量Er的Al-5Mg合金中的Er的存在形式进行了初步的分析，并结合XRD，TEM试验进行了验证。微量Er在Al-5Mg合金中主要是以Al3Er的形式存在，并且不会出现元素Mg与Er之间的金属间化合物；同时通过XRD和TEM分析证实，含微量Er（0．1％～0．7％）的Al-5Mg合金中Er是以Al3Er相存在并且弥散分布，讨论了Al3Er相与Al基体之间的取向关系，分析了Al3Er相的存在能够改善Al-5Mg合金材料的机械性能。     

镧对含锡、锑残余元素的34CrNi3Mo钢热塑性的改善作用

采用Gleeble-1500热模拟机测定了不同含量的残余元素锡、锑及稀土镧对低氧、低硫的34CrNi3Mo钢热塑性的影响;采用SEM及EDS手段研究了稀土镧对不同锡、锑含量的钢断裂方式的影响及在其中形成夹杂物的情况。结果表明,用稀土金属可以改善低氧、低硫钢中残余元素对钢性能的危害;镧可以和钢中较低含量的锑作用生成镧锑金属间化合物,并且发现了少量的镧锡金属间化合物。     

基于二维镧-有机层和多变铜-配合物柱构建的系列3d-4f杂金属框架（摘要）

在水热条件下,六个新颖的三维层-柱状镧-过渡金属配位聚合物,LnCuX（IN）2（Ac）（H2O）（Ln=Tb,X=Br（1）;Ln=Er,X=Cl（2））,[LnCuCl（IN）2（Ac）].H2O（Ln=Gd（3）;Ln=Eu（4））和[LnCu2Br2（IN）2（Ac）（H2O）].nH2O（Ln=Dy,n=0（5）;Ln=Gd,n=0.5（6））（IN=isonicotinate,Ac=acetate）,被成功合成出来.这些化合物是通过镧-有机层和多变的铜-配合物柱连接而成.化合物1和2是同构的,其结构是由二维Ln-IN-Ac层和CuX（IN）2柱（X=Br（1）,X=Cl（2））构建的;化合物3和4是同形的,其结构是由二维Ln-IN-Ac层和二聚Cu2Cl（IN）4柱连接而成;而化合物5和6也是同构的,其结构是基于二维Ln-IN-Ac层和四聚Cu4Br4（IN）4柱构建的.磁化率研究结果表明：化合物3和6中的Ln3＋离子间存在着弱的反铁磁交换作用.化合物1～6体现了基于二维Ln-有机层与多变铜-配合物柱为建筑单元构建三维Ln-TM-有机框架的代表性例子.     

用OP作增感剂原子吸收光谱法测定微量钙

研究以表面活性剂OP作增感剂。火焰原子吸收光谱法测定微量钙的方法。试验发展OP的加入可使吸光度增加70％,分析灵敏度得到提高。同时,以0．5mg.ml^-1钾、6．0mg.ml^-1镧盐及2．0mg.ml^-18－羟基喹啉作消电离剂、释放剂和保护剂消除基体物质的干扰。据此建立了标准加入法直接测定铝酸钠溶液中微量钙的分析方法。其线性范围为0－7．5mg.L^-1。灵敏度为0．05mg.L^-1/1%。方法灵敏度高,操作简便,结果准确度和精密度满足分析要求。     

Sol-gel synthesis of K3InF6 and structural characterization of K2InC10O10H6F9, K3InC12O14H4F18 and K3InC12O12F18

K₃InF₆ is synthesized by a sol-gel route starting from indium and potassium acetates dissolved in isopropanol in the stoichiometry 1:3, with trifluoroacetic acid as fluorinating agent. The crystal structures of the organic precursors were solved by X-ray diffraction methods on single crystals. Three organic compounds were isolated and identified: K₂InC₁₀O₁₀H₆F₉, K₃InC₁₂O₁₄H₄F₁₈ and K₃InC₁₂O₁₂F₁₈. The first one, deficient in potassium in comparison with the initial stoichiometry, is unstable. In its crystal structure, acetate as well as trifluoroacetate anions are coordinated to the indium atom. The two other precursors are obtained, respectively, by quick and slow evaporation of the solution. They correspond to the final organic compounds, which give K₃InF₆ by decomposition at high temperature. The crystal structure of K₃InC₁₂O₁₄H₄F₁₈ is characterized by complex anions [In(CF₃COO)₄(OH_x)₂]^(5−2x)− and isolated [CF₃COOH_2−x]^(x−1)− molecules with x=2 or 1, surrounded by K⁺ cations. The crystal structure of K₃InC₁₂O₁₂F₁₈ is only constituted by complex anions [In(CF₃COO)₆]³⁻ and K⁺ cations. For all these compounds, potassium cations ensure only the electroneutrality of the structure. IR spectra of K₂InC₁₀O₁₀H₆F₉ and K₃InC₁₂O₁₂F₁₈ were also performed at room temperature on pulverized crystals.     

Phase relations in the K2W2O7-K2WO4-KPO3-Bi2O3 system and structure of K6.5Bi2.5W4P6O34

The phase relations in the cross-section of the K₂W₂O₇-K₂WO₄-KPO₃ containing 15 mol% Bi₂O₃ were undertaken using flux method. Crystallization fields of K_6.5Bi_2.5W₄P₆O₃₄, K₂Bi(PO₄)(WO₄), Bi₂WO₆, KBi(WO₄)₂ and their cocrystallization areas were identified. Novel phase K_6.5Bi_2.5W₄P₆O₃₄ was characterized by single-crystal X-ray diffraction: sp. gr. P−1, a=9.4170(5), b=9.7166(4), c=17.6050(7) Å, α=90.052(5)°, β=103.880(5)° and γ=90.125(5)°. It has a layered structure, which contains {K₇Bi₅W₈P₁₂O₆₈}_∞ layers stacked parallel to ab plane and sheets composed by potassium atoms separating these layers. Sandwich-like {K₇Bi₅W₈P₁₂O₆₈}_∞ layers are assembled from [W₂P₂O₁₃]_∞ and [BiPO₄]_∞ building units, and are penetrated by tunnels with K/Bi atoms inside. FTIR-spectra of K₂Bi(PO₄)(WO₄) and K_6.5Bi_2.5W₄P₆O₃₄ were discussed on the basis of factor group theory.     

KCl-KBO2-K2CO3, K2MoO4-KBO2-K2CO3, and K2WO4-KBO2-K2CO3 ternary systems

phase diagrams of KCl-KBO₂-K₂CO₃, K₂MoO₄-KBO₂-K₂CO₃, and K₂WO₄-KBO₂-K₂CO₃ ternary systems were studied by a calculation-experimental method and differential thermal analysis (DTA). The coordinates of ternary eutectics were determined to be E ₁: 622°C, 8.5 mol % KBO₂, 56.5 mol % KCl, and 35 mol % K₂CO₃; E ₂: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂MoO₄; E ₃: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂WO₄. The specific heats of melting of the eutectics were determined.     

Li2SO4-Na2SO4-H2O和Li2SO4- K2SO4-H2O溶液的体积性质

本文用高精度数字式振荡管密度计测定了288K至318K温度范围内Li₂SO₄ + Na₂SO₄ + H₂O和 Li₂SO₄ + K₂SO₄ + H₂O三元体系的密度。混合溶液的离子强度范围从0.1到4.5 mol.kg_–1,混合溶液中Na₂SO₄和K₂SO₄的离子强度分数为0.2,0.4,0.6和0.8。用密度实验值拟合得到了不同温度下Pitzer离子相互作用模型混合参数θ_V和 ψ_V,模型的计算值与实验值的偏差在±0.002 g.cm_–3以内。用Pitzer模型计算了不同离子强度下三元体系的混合体积。     

Extension of the La7Mo7O30 structural type with La7Nb3W4O30 and La7Ta3W4O30 compounds

Two compounds of formula La₇A₃W₄O₃₀ (with A=Nb and Ta) were prepared by solid-state reaction at 1450 and 1490 °C. They crystallize in the rhombohedric space group R-3 (No. 148), with the hexagonal parameters: , and , . The structure of the materials was analyzed from X-ray, neutron and electronic diffraction. These oxides are isostructural of the reduced molybdenum compound La₇Mo₇O₃₀, which are formed of perovskite rod along [111]. An order between (Nb, Ta) and W is observed.     

SnSbBiS4-SnS and SnSbBiS4-Sn2Sb6S11 sections of the SnS-Sb2S3-Bi2S3 ternary system

SnSbBiS₄-SnS and SnSbBiS₄-Sn₂Sb₆S₁₁ sections were studied by physicochemical methods (DTA, X-ray powder diffraction, microstructure observation, and microhardness measurements). These sections were found to be eutectic quasi-binary sections of the SnS-Sb₂S₃-Bi₂S₃ ternary system. Solid solution regions based on the initial components were found on either side of the sections. Alloys in the solid solution region are p-type semiconductors.     

Preparation and structure of NaSr0.5Al2B2O7 and NaCa0.5Al2B2O7

Two compounds NaSr_0.5Al₂B₂O₇ and NaCa_0.5Al₂B₂O₇, have been found to crystallize into a new structure type by Rietveld refinement from X-ray powder diffraction data. Their structure belongs to hexagonal space group P6₃/m, with lattice parameters of , for NaSr_0.5Al₂B₂O₇ and , for NaCa_0.5Al₂B₂O₇, respectively. The structure is built up by [Al₂B₂O₇]²⁻ double layer and Na⁺/Ca²⁺ or Na⁺/Sr²⁺ ions alternatively stacking along the c-axis. The sites in the inter-double layer are fully occupied jointly by Na and Ca or Sr, but the intra-double layer sites are only half occupied solely by Na. A mechanism of the transition of the structure from CaAl₂B₂O₇ to present structure type by replacing only 1% Ca by Na (2%) as observed by Chang and Keszler (Mater. Res. Bull. 33 (1998) 299) is also proposed.     

Li2O-TiO2-SiO2-P2O5和Li2O-TiO2-Al2O3-P2O5体系锂离子固体电解质的制备及性能研究

一些具有NASICON型网格结构的固体电解质具有高的电导率和好的稳定性,NASICON的意思是Na Super Ionic Conductor[1]。当NaZr2(PO4)3中P5 被Si4 部分取代时便可以得到具有NASICON结构的Na1 xZr2SixP3-xO12体系,其具有高的钠离子电导率。然而有相同结构的Li1 xZr2SixP3-xO12体系的离子电导率却很低,这是因为Li 半径太小,而NASICON三维网格结构的离子通道太大,两者不匹配而使电导率下降[2]。但当LiZr2(PO4)3中Zr4 被离子半径小些的Ti4 取代,所得LiTi2(PO4)3的通道就与Li 半径相匹配,适合于锂离子的迁移,从而使其电导率…     

Structural chemistry of Sr3Cr2WO9, Ca3Cr2WO9, and Ba3Cr2WO9

We have studied the preparation and crystallographic structure of three perovskite-type compounds: Sr₃Cr₂WO₉, cubic, the lattice parameter of which is a = 7.812Å; Ca₃Cr₂WO₉, tetragonal, the lattice parameters of which are a = 5.408 Å and c = 7.635Å; and Ba₃Cr₂WO₉, hexagonal, the lattice parameters of which are a = 5.691 Å and c = 13.957Å. We have compared these three structures and shown the relationship between the dimensions of the alkaline-earth metal and the existence of the different structures.     

Phase diagram of the In3As2Se6-In3As2S3Se3 system

The In₃As₂Se₆-In₃As₂S₃Se₃ system has been investigated by methods of physicochemical analysis (DTA, X-ray powder diffraction, MSA) and by microhardness and density measurements. The phase diagram of the system, which is the quasi-binary section of the As-In-S-Se quaternary system, has been constructed. The region of the In₃As₂Se₆-based solid solutions is extended to 7 mol %, and the In ₃As₂S₃Se₃-based region to 15 mol %. A new quaternary compound In₆As₄S₃Se₉ is found in the system. Original Russian Text ? I.I. Aliev, R.S. Magammedragimova, A.A. Farzaliev, Dzh. Veliev, 2009, published in Zhurnal Neorganicheskoi Khimii, 2009, Vol. 54, No. 4, pp. 691–694.