基于LQG最优控制法的压电智能结构独立模态空间控制

采用压电材料作为传感器和驱动器对智能结构振动主动控制进行研究,基于机电耦合的压电智能结构传感和驱动方程,将振动控制动力学方程变换到模态空间对方程进行解耦。通过计算结构最大应变,确定压电元件的最佳粘贴位置。考虑到系统过程噪声和量测噪声的影响,设计Kalman滤波器,采用基于线性二次型高斯(LQG)最优控制的独立模态空间控制方法对压电智能结构的振动进行控制。最后以压电智能悬臂梁为例进行控制仿真,验证了此方法的有效性。     

含压电材料智能结构动态特性的研究

本文推导了含压电材料智能结构有限元动力方程,讨论了智能结构系统的动态特性,得到了模态形状和相应的模态电压以及考察了具有分布的压电传感器和执行器的四边简支方板的各阶固有频率随以馈增益的变化规律,这些结果将在智能结构控制的优化设计中起到了很大的作用。     

Construction of polynomial matrix using block coefficient matrix representation auto-regressive moving average model for actively controlled structures

The polynomial matrix using the block coefficient matrix representation auto-regressive moving average (referred to as the PM-ARMA) model is constructed in this paper for actively controlled multi-degree-of-freedom (MDOF) structures with time-delay through equivalently transforming the preliminary state space realization into the new state space realization. The PM-ARMA model is a more general formulation with respect to the polynomial using the coefficient representation auto-regressive moving average (ARMA) model due to its capability to cope with actively controlled structures with any given structural degrees of freedom and any chosen number of sensors and actuators. (The sensors and actuators are required to maintain the identical number.) under any dimensional stationary stochastic excitation. The project supported by the National Natural Science Foundation of China (50278054)     

LINEAR ACTIVE STRUCTURES AND MODES （ Ⅱ ） — DISCRETE SYSTEMS AND BEAMS

The basic concepts about the active structures and some attributes of the modes were presented in paper “Liner Active Structures and Modes ( Ⅰ ) “. The characteristics of the active discrete systems and active beams were discussed, especially, the stability of the active structures and the orthogonality of the eigenvectors. The notes about modes were portrayed by a model of a seven-storeyed building with sensors and actuators. The concept of the adjoint active structure was extended from the discrete systems to the beams that were the representations of the continuous structures. Two types of beams with different placements of the measuring and actuating systems were discussed in detail. One is the beam with the discrete sensors and actuators, and the other is the beam with distributed sensor and actuator function. The orthogonality conditions were derived with the modal shapes of the active beam and its adjoint active beam. An example shows that the variation of eigenvalues with feedback amplitude for the homo-configuration and non-homo-configuration active structures.     

压电智能环形板的主动控制

对在不同位置粘有任意多组压电传感器和压电执行器的轴对称弹性环形薄板的振动控制进行了研究．根据压电执行元件的等效作用量得到了压电智能环板的振动控制方程和传感方程,再利用分离变量法以及由传感器测得的电量和作用在执行器上电压之间的控制模式得到振动方程的全解．实行了对整体结构的主动控制．对不同的压电片布置进行了数值计算．结果表明：当离散分布压电元件布置越密,振动衰减的效果越佳     

利用线性模型估计的传感器优化布置算法

提出了一种基于线性模型估计的传感器布置算法.首先根据线性模型估计理论,将待监测的目标模态振型视为线性模型的设计矩阵;然后利用奇异值分解的算法,将设计矩阵分解,根据分解的前几个左奇异向量来计算各个自由度对于目标模态振型的贡献;用迭代算法来求出最优的传感器布置方案;最后,用两个算例表明该方法的有效性.     

机敏柔性梁的振动主动控制

提出了用于机敏结构中振动主动控制的仿人控制算法,对压电阻尼技术进行了理论和实验研究,给出了传感器,执行器和受控结构之间的关系,用ＰＺＴ作执行元件实现了柔性梁振动主动控制系统,给出了实验结果。     

Wing box transonic-flutter suppression using piezoelectric self-sensing diagonal-link actuators

The main objective of this research is to study the capability of Piezoelectric (PE) self-sensing actuators to suppress the transonic wing-box flutter, which is a flow-structure interaction phenomenon. The unsteady general frequency modified Transonic Small Disturbance (TSD) equation is used to model the transonic flow about the wing. The wing-box structure and the piezoelectric actuators are modeled using the equivalent plate method, which is based on the first-order shear deformation plate theory (FSDPT). The piezoelectric actuators are used as diagonal-links. The optimal electromechanical-coupling conditions between the piezoelectric actuators and the wing are collected from previous work. Three main different control strategies; Linear Quadratic Gaussian (LQG) which combines the Linear Quadratic Regulator (LQR) with the Kalman Filter Estimator (KFE), Optimal Static Output Feedback (SOF), and Classic Feedback Controller (CFC); are studied and compared. The optimum actuators and sensors locations are determined using the Norm of Feedback Control Gains (NFCG) and Norm of Kalman Filter Estimator Gains (NKFEG), respectively. A genetic algorithm (GA) optimization technique is used to calculate the controller and estimator parameters to achieve a target response.     

面向压电智能结构精确变形的协同优化设计方法

智能结构集智能材料与传统材料于一体,能够实现结构的主动控制,在航空航天等领域具有巨大的应用潜力.由于其系统复杂且具有多场耦合效应,智能结构的整体式优化设计方法成为结构控制技术研究的关键之一.为了提高压电智能结构的整体性能和变形精度,提出了同时考虑压电驱动器布局(分布位置及角度)和基体结构拓扑构型的协同优化设计新方法.采用多点约束方法 (multi-point constraints,MPC)建立压电驱动器和基体结构的连接,定义一种与测量点目标位移相关的权重函数,以实现结构的精确变形控制.通过协同优化设计,压电驱动器可以获得最优的分布位置及角度,同时基体结构获得最优的拓扑构型,从而提升了压电智能结构系统的整体驱动性能和变形精度.通过进一步分析,研究了精确变形、体分比约束与结构优化构型和整体刚度的关系,以及优化结果中可能存在的传力路径畸变现象.数值算例的设计结果表明,采用协同优化设计方法,能够扩大结构的寻优空间,有效减小变形误差,实现压电智能结构的精确变形控制.     

作动器/传感器优化配置的研究进展

给出了作动器／传感器优化配置问题的数学描述,综述了作动器／传感器优化配置方法的发展现状．阐述了振动控制和模态试验中作动器／传感器优化配置的关系．并给出需要进一步研究的几个问题      

Piezoelectric Actuator Placement Optimization and Active Vibration Control of a Membrane Structure

The placement optimization of piezoelectric actuators and active vibration control of a membrane structure are studied in this paper. The classical linear quadratic regulator controllers are designed to suppress the unwanted vibration. Simulation results indicate that the optimal locations of piezoelectric actuators are affected deeply by the additional mass and stiffness of actuators, the computational efficiency of particle swarm optimizer is higher than that of genetic algorithm for this particular problem, and the control performance of optimally placed actuators is better than that of non-optimally placed actuators.     

REDUCTION APPROACHES FOR VIBRATION CONTROL OF REPETITIVE STRUCTURES

The reduction approaches are presented for vibration control of symmetric, cyclic periodic and linking structures. The condensation of generalized coordinates, the locations of sensors and actuators, and the relation between system inputs and control forces are assumed to be set in a symmetric way so that the control system posses the same repetition as the structure considered. By employing proper transformations of condensed generalized coordinates and the system inputs, the vibration control of an entire system can be implemented by carrying out the control of a number of sub-structures, and thus the dimension of the control problem can be significantly reduced.     

Coupled buckling and postbuckling analysis of active laminated piezoelectric composite plates

A theoretical framework for analyzing the pre- and postbuckling response of composite laminates and plates with piezoactuators and sensors is presented. The mechanics include nonlinear effects due to large rotations and stress stiffening, and are incorporated into a coupled mixed-field piezoelectric laminate theory. Using the previous mechanics, a nonlinear finite element method and an incremental-iterative solution are formulated for the analysis of nonlinear adaptive plate structures subject to in-plane electromechanical loading. A novel eight-node nonlinear plate finite element is also developed. Evaluation cases predict the buckling and postbuckling response of adaptive composite beams and plates with piezoelectric actuators and sensors. The case of piezoelectric buckling and postbuckling induced by the actuators is addressed and quantified. Finally, the possibility to actively mitigate the mechanical buckling and postbuckling response of adaptive piezocomposite plates is illustrated.     

Gradient surface ply model of SH wave propagation in SAW sensors

Investigation of the propagation of the wave in SAW sensors is a basis for the research and design of the sensors. With the advance of the sensor, both the effect of environment on the surface ply and the geometry of waveguide are complicated. To consider the complication, a model with gradient surface ply and multilayer waveguide of SH wave propagation in sensor is proposed. The equation of wave velocity is derived by a transfer matrix method. Through the equation, the function of wave velocity increment via the change of parameters in the surface ply is obtained. The effect of the inhomogeneity on the function is also studied. Finally, some influencing factors of the behavior of the sensor are discussed. This study was supported by the National Natural Science Foundation of China (No. 59635140), the Doctoral Education Foundation of the Ministry of Education of China and Aeronautics Foundation of China.     

Active vibration control and suppression for integrated structures

Spacesmictures,aircraftstrUctures,satellitesandsoonarerequiredtobelightinweightduetotherequirementofoperation.TheyarealsolightlydampedbecauseofthelowinternaldampingofthematerialsusedintheirconstrUction.Thus,theywillgeneraiClargeamplitudevibration,whichmayreducetheprecisionofoperationandaffectthePerformanceofoperation.Itisessentialtousesuitablecontrolsystemtocontrolthevibrationofsimctures.Sincethesesmicturesaredistributedparametersystemshavinganinfinitesetofvibrationmodes,thecontrolsystemwith…     

飞机某复合材料弯管的振动主动控制

针对某飞机上典型的复合材料弯管结构的振动 ,采用压电元件作为传感器和作动器 ,通过有限元分析其振动模态以确定压电元件的施加位置 ,进一步利用自适应前馈控制策略 ,对其振动进行了主动控制 ,最终取得了有效的减振效果     

Approximation d'un contrôle optimal distribué par un circuit électronique réparti: application au contrôle de vibrations

This paper focuses on the design of distributed control related to distributed mechanical systems. Sensors and actuators are assumed to be numerous and periodically distributed. The problem adressed in this paper is: “Can we find a way to approximate an optimal control law with a distributed electronic circuit?” A solution to this problem is proposed in the framework of vibration control of a thin plate using piezoelectric actuators and sensors.     

Finite-macro-element for modelling thin structures with integrated piezoelectric sensor-actor-elements

A finite element technique is presented, which integrates the behaviour of circular sensor-actuator-elements within a macro-element. The macro-element is applied to the investigation of thin structures, if the excitation and the measurement of membrane vibrations are accomplished by piezoelectric actuators and sensors. The electromechanical equations are solved analytically within the macro-element, in order to avoid a spatial discretisation of the piezoelectric actuators. The numerical efficiency is obvious, since the discretisation of the structure becomes independent of the piezoelectric components.     

Active control of flexible beams subjected to multi-disturbance using one controller

The active control of vibration for a beam subjected to multi-disturbances is investigated based on wave propagating suppression. In this control system, there are the same numbers of the sensors, the signal inputting to the controller and the disturbances, but there is only one controller. It is a local control system, the system parameters depend only on the characteristics of the structure bounded by the sensors and the controller, and we need not take into account the boundary conditions and the properties of structures outside of this field. The system is efficient when a structure vibrates in middle and high frequency regions. Some control design rules are developed from the calculation results. The project supported by the National Natural Science Foundation of China and Post Doctorate Science Fund of China     

智能梁振动主动控制的广义位置函数法

研究了具有离散分布式压电传感器、执行器的智能梁,在外加电场作用下振动模态与外加电场之间的耦合关系,提出了智能梁主动控制的一种新的计算方法-广义位置函数法,并引入执行器位置函数的级数展开式,简化了计算,结果表明,智能梁振动控制效果与压电执行器长度、数目以及位置有密切的关系。