柔性悬臂电磁驱动光开关的仿真与制作

设计并制作了一种用于波长信道选择系统的新型柔性悬臂梁电磁驱动光开关,该光开关采用微光机电系统技术制作,由带有平面螺旋形线圈的聚酰亚胺悬臂梁、圆柱形永磁体、基座以及双面反射棱镜组成.通过改变线圈中激励电流的方向来控制开关动作.运用有限元的方法,模拟分析了线圈与永磁体之间电磁力的分布以及悬臂梁回复力、电磁力与挠度的关系.对该光开关的驱动性能进行了测试,实验结果表明：加载较小的工作电流（0.15A）,悬臂梁便可以产生较大的挠度（0.925mm）,满足波长信道选择系统光路偏转的要求. 关键词： 微光机电系统 光开关 柔性悬臂梁 电磁驱动     

一种微型光开关的设计与仿真分析

介绍了一种新型的聚酰亚胺(PI)悬臂梁式电磁驱动微机电系统(MEMS)光开关,并对其总体结构进行了设计与仿真分析.运用有限元分析的方法,设计了永磁体的最佳尺寸并优化了悬臂梁的结构;分析了聚酰亚胺悬臂梁的扭转力、电磁力与挠度的关系.当输入电流为75 mA时,聚酰亚胺悬臂梁达到平衡时的挠度约为1.02 mm,能够满足器件转换光路的要求.     

微电磁光开关的结构设计与性质模拟

基于微电磁光开关的工作原理,设计了MEMS电磁反射型光开关.采用ANSYS 9.0有限元软件分析结合Mathematica数值计算研究了微电磁光开关所需的电磁力、磁芯线圈的磁场分布、悬臂梁受电磁力的形变状态,从而获得磁芯线圈的匝数、悬臂梁位置、悬臂梁与平面磁芯线圈接触区域等结构参量.     

微电磁继电器磁场和力学性质模拟研究

运用有限元分析ANSYS和Mathematica软件对平面线圈的电磁场分布、悬臂梁与固定电极之间的电磁力、悬臂梁应力分布和受力形变等进行了理论分析和仿真模拟,为线圈结构、悬臂梁位置、悬臂梁与线圈距离的设计提供理论依据.     

一种带有U形波导的交叉信道单微环电光开关

本文利用耦合模理论,电光调制理论和传输矩阵法,提出了一个带有U形波导的交叉信道单微环电光开关的器件模型,并在谐振波长为1561 nm的情况下对该器件进行了仿真计算.结果表明,该电光开关的开关电压约为400 V,串扰小于-30 dB,插入损耗小于4 dB,开关时间仅为5.4 ps,其中微环上的上升和下降时间仅为0.32 ps.此外,该电光开关由单刀双掷开关控制,通过在微环和U形波导上加载驱动电压可实现三种开关状态,不仅可以实现光信号在两条输出信道的选择,还可以使两条信道同时有光信号输出.     

采用CCD技术的微型光机电系统光开关测试方法

在研制基于微型光机电系统技术的光电器件过程中,需要精确测定器件在给定驱动条件下的运动情况。在对制作完成的光开关进行性能测试时,由于微型光机电系统光开关的几何尺寸的限制,如果要准确测定光开关微反射镜的运动位移。将会有一定的困难。提出了一种采用线阵CCD技术的光学测量方法,实现了对光开关悬臂梁在驱动电压作用下的旋转角度的精确测量。通过理论推导得到了悬臂梁扭转角度与可测量物理量的关系．通过求解方程得到了各个物理量的数值选择对于测量结果的影响,并且给定了测量时各个物理量的参考值。通过实验测量,误差小于10％,表明这是一种具有实际意义的测量方案。     

磁共振快速T/R开关驱动器研制

在磁共振T/R开关和主动失谐线圈中广泛使用PIN管,由外部驱动器向PIN管提供驱动电源,控制其导通或截止,从而达到开关切换和线圈失谐的目的.因此,驱动器的性能直接影响T/R开关和线圈的性能.该工作提出了一种新的T/R开关驱动器设计方案.电路中门控信号与驱动电源互相隔离,同时包含了场效应管死区调整电路,提高了电路稳定性和灵活性.该电路开关切换时间可达500 ns,驱动电压和电流理论上分别可达400 V和10 A以上,具有快速、驱动能力强等特点.可用于快速T/R开关和主动失谐线圈的驱动、缩短死时间、减小发射线圈和接收线圈间的耦合.     

MOSFET驱动的单脉冲选择器

 详细地介绍了用高耐压大电流MOSFET驱动电光晶体构成单脉冲选择器的优点,阐述了适用于实现快速光开关的电光晶体的特性以及制作MOSFET驱动电路中的难点和相应的解决办法。实验显示该选择器可达到5ns的光开关速度。     

交叉相位调制对非线性光纤环镜中光脉冲传输的影响

基于耦合非线性薛定谔方程,采用分步傅里叶方法分析了在单波长信道和WDM（波分复用）4波长信道中XPM（交叉相位调制）对高速NOLM（非线性光纤环镜）光开关中脉冲传输的影响.数值计算表明：XPM造成NOLM中信号脉冲串扰与畸变,并造成NOLM开关性能的下降.WDM系统NOLM光纤环中的同向传播的各波长之间的XPM串扰比相向脉冲之间的XPM效应的影响更大,并且波长越短输出功率越低,中间信道受XPM的影响所导致的脉座现象和走离效应比两侧波长信道严重.     

单到单和单到双信道皮秒脉冲全光波长转换的实验研究

基于周期极化反转铌酸锂（PPLN）光波导级联倍频和差频（SHG+DFG）的二阶非线性效应,提出并实验研究了皮秒脉冲的可调谐波长转换以及单信道到双信道的波长转换.信号光采用重复频率为40 GHz,脉宽为1.57 ps的脉冲信号.连续抽运光由光纤环形腔激光器（FRL）提供.不同于传统的SHG+DFG型波长转换,信号光固定在PPLN光波导倍频过程的准相位匹配（QPM）波长处,通过调节抽运光的波长实现了转换空闲光的可调谐输出.当使用两个抽运光时实验观察到了单信道到双信道的波长转换.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.