脂肪族聚酰胺热膨胀行为的研究

通过热膨胀测试,示差扫描量热分析(DSC)、广角X射线衍射(WAXD)与傅里叶变换红外光谱(FTIR)等方法研究了4种脂肪族聚酰胺玻璃化转变温度(Tg)、结晶行为以及氢键强度对热膨胀行为的影响,探索了影响脂肪族聚酰胺热膨胀的本质.DSC和X射线衍射结果表明,聚酰胺中结晶部分的热膨胀系数要低于无定形部分,但聚酰胺的熔融温度和结晶度对热膨胀的影响不够明确.相比较其它脂肪族聚酰胺,聚酰胺56(PA56)具有较高的玻璃化转变温度和较低的亚甲基/酰胺基(CH2/CONH)比例,表现出较低的热膨胀系数.研究发现,在相同条件下制备的脂肪族聚酰胺体系中,CH2/CONH比例或Tg与热膨胀系数具有明显的线性关系,随着CH2/CONH比例的降低或Tg的升高,热膨胀系数显著减小.FTIR的结果表明,聚酰胺分子链间的氢键密度和氢键强度随温度升高衰减的程度是影响其热膨胀行为的关键因素.     

基于纳米羟基磷灰石溶胶的nHA/PA66复合粉体制备与表征

本文开发了一种新的制备纳米羟基磷灰石(nHA)/聚酰胺66(PA66)复合材料的方法。先用明胶包覆nHA棒状颗粒,再将其制备成以N,N-二甲基乙酰胺和甘油的混合液为溶剂的稳定溶胶。当nHA溶胶与PA66溶液混合时,相同的酰胺基团保证了二者之间良好的共混相容性,成功制备了nHA/PA66复合材料。X射线衍射(XRD)、傅立叶红外光谱分析(FTIR)、透射电镜(TEM)、扫描电镜-能谱分析(SEM-EDS)以及差热分析(DTA)和热重分析(TG)等表征了产物的形貌、结构及成分分布。结果表明：明胶对nHA颗粒具有显著的化学包覆作用,使nHA溶胶与PA66溶液得以均匀混合,均匀分布在PA66基体中,二者以氢键结合为一体。     

铵离子插层mos2的制备与表征

以剥层重堆法制备了NH 4/MoS2插层复合物,该复合物可以作为长期储存的单层MoS2,同时也可作为先驱体以便插入其它客体分子制成新的插层复合物.通过XRD、热重分析和元素分析等测试技术对该插层复合物进行了表征.结果表明,MoS2经NH 4插层后,其层间距由0.615nm增加到0.954nm,由元素分析和热重分析得出插层复合物的组成分别为(NH 4)3.1 MoS2 和(NH 4 )2.9 MoS2 . 插层复合物在空气中放置30 d后,其XRD和热重分析的结果表明该插层复合物的储存稳定性良好. 此外,插层复合物的插层程度受氯化铵溶液浓度、反应温度、反应时间等反应条件的影响,质量分数为1.0%的氯化铵溶液, 反应温度30 ℃和反应时间12 h,所得到的NH 4 /MoS2插层复合物层间距最大.     

三氟乙酸溶液中尼龙6链凝聚缠结的NMR弛豫研究

采用1D和2DNMR技术,归属了三氟乙酸(TFA)溶液中尼龙6链上的主要¹HNMR共振信号.不同温度下测定的自旋-自旋弛豫时间(t2)提供了大分子主链间凝聚缠结及TFA溶液中尼龙6链随温度变化的动力学信息.结果表明,尼龙6主链上亚甲基基团有不同程度的凝聚缠结,距离CO和NH基团越远,凝聚缠结越明显.与CO和NH基团相连的亚甲基基团的缠结不很明显,主要是因为尼龙6链间氢键的存在.升高温度,热运动加快,这些凝聚缠结逐渐减弱.NH质子的t2H值几乎不随温度变化,TFA质子的t2H值随温度升高而快速下降,表明尼龙6链间氢键随温度升高而破坏,TFA质子又与因温度升高而从尼龙6中释放出来的自由NH和CO基团形成新的氢键.     

精氨酸侧链和核酸碱基间离子氢键作用强度分析

采用MP2/6-31+G(d,p)方法优化得到了22个由精氨酸侧链与碱基尿嘧啶、 胸腺嘧啶、 胞嘧啶、 鸟嘌呤及腺嘌呤形成的氢键复合物的气相稳定结构, 使用包含BSSE校正的MP2/aug-cc-pVTZ方法计算得到了复合物的气相结合能, 通过MP2/6-31+G(d,p)方法和PCM模型优化得到了复合物的水相稳定结构, 采用MP2/aug-cc-pVTZ方法和PCM模型计算得到了复合物的水相结合能. 研究发现, 精氨酸侧链与碱基间的离子氢键作用强度与单体间电荷转移量、 氢键临界点电子密度及二阶作用稳定化能密切相关. 与中性氢键相比, 离子氢键作用具有更显著的共价作用成分. 研究还发现, 精氨酸侧链和碱基间形成的氢键复合物的稳定性次序可以通过氢键受体碱基分子上氧原子和氮原子的质子化反应焓变进行预测, 质子化反应焓变越负, 形成的氢键复合物越稳定.     

拉曼光谱研究CaCl2和MgCl2对水结构的影响

测试了CaCl2、MgCl2溶液(浓度小于1.0 mol•L-1)的OH伸缩振动区域的拉曼光谱.对所得到的拉曼光谱进行了计算机去卷积处理,并由此计算了不同溶液中水的四面体结构的百分数.研究表明,CaCl2、MgCl2对水中四面体结构有破坏作用，且CaCl2的破坏作用比MgCl2大.与17O核磁共振结果对比与分析,认为CaCl2、MgCl2虽然破坏水中的四面体结构,但通过促进含氢键数少的水分子形成氢键,故从总体上促进水的缔合结构.     

GeH4与HX(X＝F,Cl,Br)间二氢键复合物的理论研究

对GeH4与HX形成的二氢键复合物的结构特征及本质进行了探讨.在MP2/6-311 ++G(3 d,3p)水平优化、频率验证得到复合物的分子结构,通过分子的几何参数及电子密度拓扑分析,确认GeH4与卤化氢已形成了二氢键复合物.MP2/6-311 ++ G(3d,3p)水平下进行BSSE校正后的结合能为3.281到4.5...     

SiH4与HX(X=F,Cl,Br,I)形成的二氢键复合物的结构特性及本质

对SiH4与HX形成的二氢键复合物的结构特征及本质进行了探讨.在MP2/6-311++G(3d,3p)水平优化、频率验证得到复合物的分子结构,通过分子间距离及电子密度等值线图,确认SiH4与卤化氢已形成了二氢键复合物.MP2/6-311++G(3d,3p)水平下进行BSSE校正后的结合能为2.703～4.439 kJ/mol.用对称匹配微扰理论对结合能进行分解,分解结果显示,SiH4…HX(X=F,Cl,Br,I)二氢键复合物中静电能对总吸引能的贡献小于28%,并且相对稳定.这就是说SiH4…HX二氢键复合物的本质并非静电作用.而是静电能、诱导能、色散能、交换能对总结合能的贡献都非常重要.     

超细聚酰胺6粒子增韧聚丙烯体系的研究

采用磨盘形力化学反应器室温下制备了聚丙烯 (PP) /聚酰胺 6 (PA6 )超细粉体 ,研究了其粒度、粒度分布及PA6超细粒子填充对PP力学性能的影响 .结果表明 ,磨盘形力化学反应器可有效实现PP/PA6的粉碎 ,所得粉体平均粒径达微米级 ,初级粒子尺寸甚至可达纳米级 ,粒度分布呈双峰分布状态 .在PA6和PP熔点之间的温度下加工可制得PA6超细粒于填充的PP/PA6共混体系 ,其力学性能明显好于PP/PA6简单共混体系 ,30 %PA6用量下 ,拉伸强度由 2 3 .2MPa提高至 2 9 3MPa ,Izod缺口冲击强度由 4.6 2kJ/m2 提高到6 .34kJ/m2 .形貌分析结果表明 ,由于基本保持了PA6超细粉体的原始尺寸 ,填充体系中PA6相区尺寸小、分布均匀 ,与使用增容剂得到的相区结构类似 .     

P(MMA-MAA)/PEO氢键复合物的结构和性能

本文研究了P(MMA-MAA)/PEO氢键复合物的制备,结构和性能.实验结果表明,P(MMA-MAA)共聚物中MAA含量、共聚物与PEO的比值、在其水/乙醇溶液中的浓度、溶液pH值以及反应时间等对复合物的形成皆有影响.DSC,X射线衍射和显微镜观察表明,分子氢键复合限制了P(MMA-MAA)和PEO分子链的自由度,从而抑制了PEO的结晶.复合物不具备三维有序结构但仍有一定有序度.P(MMA-MAA)/PEO氢键复合物无色,透明,成膜性好,热稳定性明显优于其组分聚合物,对二氧化碳的渗透系数远小于对氧气的渗透系数.屈服应力和断裂应力远大于PEO.     

Design, syntheses, and characterization of dioxo-molybdenum(VI) complexes with thiolate ligands: effects of intraligand NH...S hydrogen bonding

Presence of the hydrogen bonding near a metal center can influence the properties of the complex. Here, we describe changes in redox and spectral properties in discrete dioxo-molybdenum centers coordinated by a single thiolato ligand that can support an intra-ligand hydrogen bond. We have utilized thiophenolato ligands that can harbor hydrogen bonding between the thiophenolato sulfur with an amide functionality creating either a five- or a six-membered ring. Methylation of the amide functionality removes the NH...S hydrogen bonding thus providing a basis for understanding the effect of hydrogen bonding. These thiophenolato ligands have been used in synthesizing dioxo-MoVI complexes of type Tp*MoO2(S-o-RC6H4), where R=CONHMe (), CONMe2 (), NHCOMe (), and N(Me)COMe (). The complexes have been characterized by NMR, infrared, and UV-visible spectroscopy. Spectroscopic data clearly indicate the presence of hydrogen bonding in both and , and stronger in , where hydrogen bonding stabilizes a five-membered ring. All complexes exhibit a Mo(VI)/Mo(V) redox couple and redox potentials are modulated by the nature of H-bonding. Compound with the electron-releasing N(Me)COMe group has the highest reduction potential and is more difficult to reduce.     

Calcium chloride rhenate(VII) dihydrate

The crystal structure of calcium chloride rhenate(VII) dihydrate, CaCl(ReO₄)·2H₂O, investigated at 85 K, consists of calcium cations, chloride anions, rhenate(VII) anions and water molecules. In the nearly tetrahedral rhenate(VII) anion, all constituent atoms lie on special positions of m2m (Re) and m (O) site symmetries. The Cl⁻ anion and water O atom lie on special positions of m2m and 2 site symmetries, respectively. The Ca²⁺ ion, also on a special position (m2m), is eight‐coordinated in a distorted square‐antiprismatic coordination mode. The crystal has a layered structure stabilized by Ca—O coordination bonds and O—H...Cl hydrogen bonds.     

Structures and properties of ruthenium(II) complexes of pyridylamine ligands with oxygen-bound amide moieties: regulation of structures and proton-coupled electron transfer

Tris(2-pyridylemthyl)amine (TPA) derivatives having two amide moieties at the 6-positions of the two pyridine rings of TPA and their Ru(II) complexes were synthesized and characterized by spectroscopic methods, X-ray crystallography, and electrochemical measurements. The complexes prepared were [RuCl(L)]PF(6) (L = N,N-bis(6-(1-naphthoylamide)-2-pyridylmethyl)-N-(2-pyridylmethyl)amine (1), N,N-bis(6-(2-naphthoylamide)-2-pyridylmethyl)-N-(2-pyridylmethyl)amine (2), N,N-bis(6-(isobutyrylamide)-2-pyridylmethyl)-N-(2-pyridylmethyl)amine (3)); the crystal structures of the three compounds were established by X-ray crystallography. In variable-temperature (1)H NMR spectra of 1 and 2 in CD(3)CN solutions, the pi-pi stacking in 1 was too rigid to exhibit any fluxional motions in NMR measurements; however, the pi-pi stacking of 2 was weaker and showed fluxional behavior in nearly T-shaped pi-pi interaction for the 2-naphthly groups (DeltaH degrees = -2.3 kJ mol(-1); DeltaG degrees = -0.9 kJ mol(-1) and DeltaS degrees = -7.7 J mol(-1) K(-1) at 233 K in CD(3)CN). For each of these three complexes, one of the amide moieties coordinated to the Ru(II) center through an amide oxygen. The other uncoordinated amide N-H formed intramolecular hydrogen bonding which remained intact even in aqueous media, indicating the intramolecular hydrogen bonding was geometrically compelled to form. The amide coordination is also stabilized and strengthened by the hydrogen bonding, so that the structure of each compound is maintained in solution. It is suggested that this hydrogen bonding lowers the redox potentials of the Ru(II) centers due to polarization of the coordinated amide C=O bond, in which the oxygen atom becomes more electrostatically negative and its electron-donating ability is strengthened. The N-H protons in the coordinated amide moieties were found to undergo a reversible deprotonation-protonation process, and the redox potentials of the Ru(II) centers could be regulated in the range of 500 mV in CH(3)CN solutions. The Pourbaix diagram for 1 clearly showed that this proton-coupled redox behavior is a one-electron/one-proton process, and the pK(a) value was estimated to be approximately 6.     

Spectroscopic study of conformation changes of bovine serum albumin in aqueous environment

The secondary structural changes of protein aqueous solutions with and without calcium cations were investigated by attenuated total reflection-Fourier transform infrared (ATR-FTIR) technology.     

Nonconventional hydrogen bonding between clusters of gold and hydrogen fluoride

The bonding patterns between small neutral gold Au(3 < or = n < or = 7) and hydrogen fluoride (HF)(1 < or = m < or = 4) clusters are discussed using a high-level density functional approach. Two types of interactions, anchoring Au-F and F-H...Au, govern the complexation of these clusters. The F-H...Au interaction exhibits all the characteristics of nonconventional hydrogen bonding and plays a leading role in stabilizing the lowest-energy complexes. The anchor bonding mainly activates the conventional F-H...F hydrogen bonds within HF clusters and reinforces the nonconventional F-H...Au one. The strength of the F-H...Au bonding, formed between the terminal conventional proton donor group FH and an unanchored gold atom, depends on the coordination of the involved gold atom: the less it is coordinated, the stronger its nonconventional proton acceptor ability. The strongest F-H...Au bond is formed between a HF dimer and the singly coordinated gold atom of a T-shape Au4 cluster and is accompanied by a very large red shift (1023 cm(-1)) of the nu(F-H) stretch. Estimations of the energies of formation of the F-H...Au bonds for the entire series of the studied complexes are provided.     

聚酰胺热氧化降解机理

通过详细分析测定反应产物 ,研究了聚酰胺 (PA6)的热氧化降解机理 .用化学方法测定了PA6热氧化过程中几种主要基团含量的变化 ,对PA6热氧化的气相挥发产物进行收集和分析鉴定 ,还对经过氧化的PA6样品进行水解并用GC MS法对水解产物进行了分析鉴定 .在这些实验结果的基础上 ,提出了较完整的聚酰胺热氧化降解机理 .该机理包含了自由基在与酰胺基的羰基相连的亚甲基上的夺氢反应及一系列自由基加成环化和诱导断链的反应 ,能很好地解释反应产物的分析结果 .     

Investigating the effect of hydrogen bonding environments in amide cleavage reactions at zinc(II) complexes with intramolecular amide oxygen co-ordination

Amide oxygen co-ordination to a zinc(II) ion around a hydrogen bonding microenvironment is a common structural/functional feature of metalloproteases. We report two strategies to position hydrogen bonding groups in the proximity of a zinc(II)-bound amide oxygen, and we investigate their effect on the stability of the amide group. Polydentate tripodal ligands (6-R1-2-pyridylmethyl)-R2 (R1= NHCOtBu, R2= N(CH2-py-6-X)2 X = H L1, X = NH2, H L2, X = NH2 L3) form [(L)Zn]2+ cations (L =L1, 1; L2, 2; L3, 3) with intramolecular amide oxygen co-ordination (1-3), and intramolecular N-H...O=C(amide) hydrogen bonding (2, 3) rigidly fixed by the ligand framework. 1-3 undergo cleavage of the tert-butyl amide upon addition of Me4NOH.5H2O (1 equiv.) in methanol at 50(1) degrees C. Under these conditions the half-life, t(1/2), of the amide bond is 0.4 h for 1, 9 h for 2 and 320 h for 3. Mononuclear zinc(II) complexes of (6-NHCOtBu-2-pyridylmethyl)-R2(R2= N(CH2CH2)2S) L4 and chelating N2 ligands without hydrogen bonding groups (1,10-phenanthroline L5, 2-(aminomethyl)pyridine L6) as control compounds, and with an amino hydrogen bonding group (6-amino-2-(aminomethyl)pyridine L7) have been synthesised. Amide cleavage is in this case faster at the zinc(II) complex with the amino hydrogen bonding group. Thus, hydrogen bonding environments can both accelerate and slow down amide bond cleavage reactions at zinc(II) sites. Importantly, the magnitude of the effect exerted by the hydrogen bonding environments was found to be significant; 800-fold rate difference. This result highlights the importance of hydrogen bonding environments around metal centres in amide cleavage reactions, which may be relevant to the chemistry of natural metalloproteases and applicable to the design of more efficient artificial protein cleaving agents.     

Bis­(dicyan­amido)(diethyl­enetri­amine‐κ3N)copper(II) and (dicyan­amido)(tri­ethyl­enetetr­amine‐κ4N)copper(II) dicyan­amide

Two new complexes, [Cu(C₂N₃)₂(dien)] (dien is diethyl­ene­tri­amine, C₄H₁₃N₃), (I), and [Cu(C₂N₃)(trien)](C₂N₃) (trien is triethyl­ene­tetr­amine, C₆H₁₈N₄), (II), have been characterized by single‐crystal X‐ray diffraction. Both complexes display a distorted tetragonal–pyramidal geometry. In (I), the Cu atom is coordinated in the basal plane by three diethyl­ene­tri­amine N atoms [Cu—N = 2.000 (2), 2.004 (2) and 2.025 (2) Å] and one terminal N atom [Cu—N = 1.974 (2) Å] from one monodentate dicyan­amide group, and in the apical position by one terminal N atom [Cu—N = 2.280 (2) Å] from the other monodentate dicyan­amide group. In (II), the Cu atom is surrounded by four triethyl­ene­tetr­amine N atoms [Cu—N = 2.012 (2), 2.014 (2), 2.019 (2) and 2.031 (2) Å in the basal plane] and a terminal N atom [Cu—N = 2.130 (2) Å in the apical site] from one monodentate dicyan­amide group. The other dicyan­amide anion is not directly coordinated to the metal atom. In both (I) and (II), hydro­gen‐bond interactions between the uncoordinated terminal N atoms of two dicyan­amide ions and the amine H atoms lead to the formation of three‐dimensional networks.     

Relation between intramolecular NH...S hydrogen bonds and coordination number in mercury(II) complexes with carbamoylbenzenethiol derivatives

A novel series of bis(carbamoylthiophenolato)mercury(II) complexes, [Hg(S-RNHCOC6H4)2] (1, R = 2-t-Bu; 2, R = 2-CH3; 3, R = 2-C6H5CH2; 4, R = 4-t-Bu), and a tetrakis(carbamoylthiophenolato)mercury(II) complex, (NEt4)2[Hg-(S-2-CH3NHCOC6H4)4] (5), were synthesized and characterized by 1H NMR, IR, 199Hg NMR, and crystallographic analyses. The bis(carbamoylthiophenolato)mercury complexes 1-3 do not have intramolecular NH...S hydrogen bonds between the amide NH group and the sulfur atom coordinated to mercury, whereas the tetrakis(thiophenolato)mercury complex 5 does have an intramolecular NH...S hydrogen bond. A relatively weak NH...S hydrogen bond in 5 can be seen in the 1H NMR spectra and the IR spectra in chloroform and in the solid state. The 199Hg NMR spectra in bis(carbamoylthiophenolato)mercury complexes 1-4 show a downfield shift, with an increase in the flow of electrons to mercury(II) from the oxygen atom due to the intramolecular Hg...O bonding interaction. Conversely, the 199Hg NMR spectra in 5 show a high-field shift with a decrease in the flow of electrons to mercury(II) from the sulfur atom due to the intramolecular NH...S hydrogen bond.     

Supramolecular Self‐Assembly of Histidine‐Capped‐Dialkoxy‐Anthracene: A Visible‐Light‐Triggered Platform for Facile siRNA Delivery

Supramolecular self‐assembly of histidine‐capped‐dialkoxy‐anthracene (HDA) results in the formation of light‐responsive nanostructures. Single‐crystal X‐ray diffraction analysis of HDA shows two types of hydrogen bonding. The first hydrogen bond is established between the imidazole moieties while the second involves the oxygen atom of one amide group and the hydrogen atom of a second amide group. When protonated in acidic aqueous media, HDA successfully complexes siRNA yielding spherical nanostructures. This biocompatible platform controllably delivers siRNA with high efficacy upon visible‐light irradiation leading up to 90 % of gene silencing in live cells.