单偏振控制器环形腔光纤激光器实验研究

理论分析了非线性偏振旋转环形腔作为类饱和可吸收体获得脉冲的物理机理。在光纤环形腔结构中,采用单个偏振控制器实现了非线性偏振旋转锁模,直接获得了脉冲宽度为131 fs的超短脉冲输出。实验中,采用性能稳定的976 nm半导体二极管激光器作为抽运源,使用高掺杂浓度的Er3 光纤为增益介质,通过调节偏振控制器,获得了光谱谱宽(3 dB带宽处)为23.5 nm的稳定锁模脉冲输出。脉冲中心波长为1535.9 nm,平均功率为5.91 mW,脉冲重复率为11.20 MHz。     

Linearly polarized operation of Yb-doped fiber laser by Brewster's angle-polished fiber end

<正>A new method to obtain linear polarization operation by Brewster's angle-polished fiber end is demonstrated. By using the special polarization operation technique together with introducing a narrow-linewidth fiber grating into the laser cavity,a cladding-pumped linear polarization and single-transverse-mode (M~21.1) Yb-doped fiber laser with narrow linewidth whose full-width at half-maximm(FWHM) is less than 0.2 nm,is obtained in a simple configuration.The output power is up to 10 W which is continuouswave output at 1085 nm,and the slope efficiency is 63%with respect to the coupled pump power and 75%with respect to the absorbed pump power,respectively.The measured 21-dB polarization extinction ratio does not degrade with the output power.The simplicity of such an approach is highly beneficial for a number of applications,including the use of a fiber laser for the nonlinear wavelength conversion (especially for the intracavity frequency doubling) and for the coherent and spectral beam combination.     

基于多模光纤滤波器的可调谐掺铒光纤激光器

研究了一种新型、全光纤、宽带可调谐环形腔掺铒光纤激光器。该激光器利用由单模-多模-单模光纤组成的滤波器实现波长可调谐及激光器的全光纤结构。该滤波器将多模光纤缠绕在偏振控制器上,两端分别与一段单模光纤相连,通过调整偏振控制器的状态,实现了中心波长1542～1560nm的不同激光输出。单波长连续可调谐激光器的波长可调范围为18nm,边模抑制比大于40dB,3dB线宽为0.096nm;进一步调整偏振控制器的状态和抽运功率,实验同时得到了连续可调谐的双波长、三波长等多波长激光输出。对于可调谐的多波长激光器,通过调整偏振控制器的状态,可实现波长间隔及输出中心波长两者可调。     

基于非线性偏振旋转效应的多波长光纤激光器

多波长光纤激光器是未来波分复用光通信系统的理想光源,提出和展示了一个基于非线性偏振旋转效应的多波长光纤激光器,非线性偏振旋转诱导的强度相关非均匀损耗能有效地抑制均匀加宽增益介质掺铒光纤中的模式竞争,从而使光纤激光器在室温下产生稳定的多波长输出,实验实现了最多18个波长的多波长输出.另外,此激光器没有使用传统的滤波器,而是在激光腔内插入一段保偏光纤,保偏光纤与偏振相关隔离器构成一等效Lyot双折射光纤周期性滤波器.利用这种在线型的双折射光纤滤波器简化了光纤激光器的结构,使它更易于集成.还实验研究了多波长输出随抽运功率的演化,发现抽运功率对多波长的均匀性影响很大.     

Performance of a wavelength-tunable erbium-doped fiber laser using a Sagnac interferometer

We experimentally demonstrate a wavelength-tunable erbium-doped fiber laser that is composed of a ring cavity and a single-mode fiber Sagnac interferometer in a new and simple arrangement. We find that the fiber laser output wavelength is tunable by adjusting the filter effect of the Sagnac fiber loop through a fiber polarization controller set there. The quasi-single-wavelength continuously tunable laser outputs could be achieved within some wavelength range. The multi-wavelength laser outputs could also be observed under some appropriate settings of the polarization controller. A theoretical demonstration of the wavelength tunability about the transmission-type Sagnac loop filter has also been achieved using the Jones calculus theory.     

Low-threshold single-wavelength all-fiber laser generating cylindrical vector beams using a few-mode fiber Bragg grating

We propose and demonstrate a low-threshold single-wavelength all-fiber laser generating cylindrical vector beams using a few-mode fiber Bragg grating. Both radially and azimuthally polarized beams have been generated with very good modal symmetry and polarization purity higher than 94%. The radially and azimuthally polarized modes can be switched by simply adjusting the polarization controllers built in the fiber laser cavity. This fiber laser operates at a single wavelength of 1053 nm with a 3 dB linewidth of less than 0.02 nm, signal-to-background ratio of more than 55 dB, and a threshold as low as 16 mW. A new method for the polarization purity measurement is also proposed.     

200 W级高亮度半导体激光器光纤耦合模块

光纤激光器系统需要高可靠性、高亮度、高功率光纤耦合输出二极管激光器模块作为泵浦源。基于mini-bar二极管激光器芯片,采用光束精密准直技术、自由空间合束技术来获得高亮度、高功率光纤耦合输出,针对光纤芯径为200 m、数值孔径为 0.22的多模光纤,开展了线偏振二极管激光光纤耦合实验,实验结果表明：光纤稳定输出功率达280 W,对应亮度为5.87 MW/（cm2sr）,电-光效率为45.0%。采用偏振合束技术,光纤预期输出功率可达500 W,对应亮度超过10 MW/（cm2sr）。该方法可应用于研制数百瓦级高亮度二极管激光光纤耦合输出激光器模块。     

高能量掺Yb偏振型大模场面积光子晶体光纤孤子锁模飞秒激光器

实验研究了基于掺Yb偏振型大模场面积光子晶体光纤的孤子锁模激光器,获得了高脉冲能量的飞秒激光输出. 激光器基于线形腔结构,利用光栅对补偿腔内色散,并通过半导体可饱和吸收镜实现锁模的自启动. 实验中从振荡级直接获得了平均功率为700mW, 重复频率为47.3MHz(对应于14.8 nJ的单脉冲能量),脉冲宽度为518 fs的稳定锁模脉冲输出. 与普通孤子锁模飞秒光纤激光器相比,输出的单脉冲能量提高了两个数量级. 关键词： 光子晶体光纤 飞秒 光纤激光器 孤子锁模     

Waveband switchable multi-wavelength erbium-doped fiber ring laser based on wavelength-dependent polarization rotation mechanism

A waveband switchable multi-wavelength erbium-doped fiber ring laser based on wavelength-dependent polarization rotation mechanism and birefringence-based in-line comb filter is proposed and demonstrated. The two lasing wavebands, around 1530 and 1560 nm region, can be efficiently switched by simply rotating the polarization controllers (PCs). The channel spacing is 0.4 nm which was determined by the length of polarization maintain fiber (PMF) used in the experiment. The experimental results show that the waveband switchable is an intrinsic feature of multi-wavelength fiber ring lasers by incorporating a passive polarizer in the laser cavity.     

Passively Q-switched mode-locking Erbium-doped fiber laser with net-normal dispersion using nonlinear polarization rotation technique

We experimentally demonstrate a passively Q-switched mode-locking (QML) operation in an Erbium-doped fiber ring laser with net normal dispersion by using nonlinear polarization rotation technique. A 2 m long section of dispersion compensating fiber (DCF) with extra large positive dispersion was inserted into the cavity to ensure the fiber laser working in the region of net positive dispersion. By carefully adjusting the polarization controller, both uniform dissipative mode-locking pulses with fundamental repetition rate and QML pulse trains with tunable repetition rate from 71.58 to 98.83 kHz are achieved. It is found that the QML operation is caused by the interaction between the polarization state of the pulse and the intracavity polarizer.     

Optical coherent detection Brillouin distributed optical fiber sensor based on orthogonal polarization diversity reception

In Brillouin distributed optical fiber sensor, using optical coherent detection to detect Brillouin scattering optical signal is a good method, but there exists the polarization correlated detection problem. A novel detecting scheme is presented and demonstrated experimentally, which adopts orthogonal polarization diversity reception to resolve the polarization correlated detection problem. A laser is used as pump and reference light sources, a microwave electric-optical modulator (EOM) is adopted to produce frequency shift reference light, a polarization controller is used to control the polarization of the reference light which is changed into two orthogonal polarization for two adjacent acquisition periods. The Brillouin scattering light is coherently detected with the reference light, and the Brillouin scattering optical signal is taken out based on Brillouin frequency shift. After electronic processing, better Brillouin distributed sensing signal is obtained. A 25-km Brillouin distributed optical fiber sensor is achieved.     

双包层掺Yb3+光纤环形脉冲激光形成研究

对采用环形腔结构,由偏振敏感的光隔离器构成超短脉冲掺Yb³⁺光纤激光器输出的动力学特性进行了数值模拟.模拟表明:在没有进行色散补偿的掺Yb³⁺光纤环形激光器中,采用非线性偏振旋转的附加脉冲锁模技术,通过改变偏振控制器的方向,可以使激光器工作在不同的区域.实验用976 nm的半导体激光器作为泵浦源,通过调整偏振控制器,实验观测到掺Yb³⁺环形激光器工作在稳态和自脉动状态,其脉动的周期由光纤激光器腔长决定.     

220 μJ monolithic single-frequency Q-switched fiber laser at 2 μm by using highly Tm-doped germanate fibers

We report a unique all fiber-based single-frequency Q-switched laser in a monolithic master oscillator power amplifier configuration at ~1920 nm by using highly Tm-doped germanate fibers for the first time. The actively Q-switched fiber laser seed was achieved by using a piezo to press the fiber in the fiber Bragg grating cavity and modulate the fiber birefringence, enabling Q-switching with pulse width and repetition rate tunability. A single-mode polarization maintaining large core 25 μm highly Tm-doped germanate fiber was used in the power amplifier stage. For 80 ns pulses with 20 kHz repetition rate, we achieved 220 μJ pulse energy, which corresponds to a peak power of 2.75 kW with transform-limited linewidth.     

宽带可调谐掺Yb3+双包层光纤激光器的研究

利用闪耀光栅构成可调谐Littrow外腔,对掺Yb³⁺双包层光纤激光器的波长调谐输出进行了实验研究.激光调谐输出波长范围70nm.针对光纤内的双折射效应对激光的输出功率的影响,实验中使用了在线光纤偏振控制器,从而有效地减小了调谐曲线的起伏及其与荧光谱的差别,并得到了窄线宽、线偏振、宽带调谐的激光输出.     

Non-contact detection of laser-generated surface acoustic waves using fiber optic Sagnac interferometer

A high powered Q-switched Nd:YAG laser was used to excite the surface waves, and an optical fiber sensor was used to detect the out-of-plane displacements due to the propagating waves. This sensor is based on the fiber optic Sagnac interferometer, which has the path-matched configuration and does not require active stabilization. Quadrature phase bias between two interfering laser beams in the Sagnac loop is applied by controlling the birefringence in an optical path using a fiber polarization controller. A stable quadrature phase bias can be confirmed by observing the interferometer output according to the change of phase bias. Additional signal processing is not needed for the detection of ultrasonic waves using the Sagnac interferometer. The performance of the fiber optic Sagnac interferometer was investigated, and laser-generated surface wave signals were detected using this fiber optic sensor. The developed fiber optic sensor configured in this study is very simple and is effective for non-contact detection of ultrasonic waves.     

输出近百纳焦耳脉冲能量的光子晶体光纤锁模激光器

设计并搭建了一种支持百纳焦耳量级的单脉冲能量输出的锁模光纤激光器.激光器基于σ型腔结构,采用掺Yb偏振型大模场面积光子晶体光纤作为增益介质,利用半导体可饱和吸收镜实现自启动锁模.激光器内没有色散补偿机理,使其工作在全正色散锁模状态.通过在谐振腔内引入多通长腔使激光器的重复频率降低至11.1 MHz,直接获得了平均功率为1.08 W,单脉冲能量为 97 nJ,脉冲宽度为4.17 ps的稳定锁模脉冲输出,经腔外色散补偿,脉冲宽度压缩至740 fs.     

A linearly-polarized tunable Yb-doped fiber laser using a polarization dependent fiber loop mirror

A Ytterbium-doped linearly-polarized fiber laser is constructed with a polarization maintaining fiber Sagnac loop mirror. The fiber loop mirror made of polarization maintaining fiber coupler has a polarization dependent reflectivity, which provides the necessary polarization discrimination between the slow and fast axes. With a fiber Bragg grating written in normal polarization maintaining fiber as an output coupler, laser output of up to 5.6 W at 1070 nm is generated with a polarization extinction ratio of > 20 dB and an overall efficiency of 55%. The broadband polarization dependent reflection of the fiber loop mirror offers advantages of easy spectral tuning and simple linearly-polarized laser generation.     

Tunable dual-wavelength fiber laser based on a polarization-maintaining fiber Bragg grating and a Hi-Bi fiber optical loop mirror

We demonstrate experimentally the operation of a linear cavity dual-wavelength fiber laser using a polarization maintaining fiber Bragg grating (PM-FBG) as an end mirror that defines two closely spaced laser emission lines. The PM-FBG is also used to tune the laser wavelengths. The total tuning range is ∼8 nm. The laser operates in a stable dual-wavelength mode for an appropriate adjustment of the cavity losses for the generated wavelengths. The high birefringence (Hi-Bi) fiber optical loop mirror (FOLM) is used as a tunable spectral filter to adjust the losses. The FOLM adjustment was performed by the temperature control of the Hi-Bi fiber.     

Frequency doubling of narrow-linewidth pulsed fiber laser

A pulsed master oscillator power amplifier system is constructed using a double-cladding polarized Ybdoped fiber and an all-fiber Q-switched narrow-linewidth pulsed laser used as seed laser.This system has a high repetition rate and provides a nanosecond pulsed laser with a narrow linewidth and linear polarization.Moreover,it generates amplified radiation with up to 14 W of average power,narrow linewidth(full-width at half-maximum is smaller than 0.12 nm),linear polarization at 1 080-nm wavelength,repetition rate of 51 kHz,and pulse duration of approximately 50 ns.Based on this pulsed amplified radiation,3.5 W of green laser,with an optical-to-optical efficiency of 27.3%,is obtained via single-pass frequency doubling using a noncritical phase matching KTP crystal.     

Photonics True-Time-Delay Unit for Phased-Array Antenna Using Multiwavelength Fiber Laser Based on a Sagnac Interferemetric Filter

A photonics true-time-delay system for phased array beamforming using a chirped grating-based time-delay element and a novel multiwavelength erbium-doped fiber ring laser source employing a Sagnac filtering mirror is proposed. The Sagnac filtering mirror consists of a polarization maintaining directional coupler and two pieces of polarization maintaining fibers. The lasing wavelength and number are determined by properly adjusting the polarization controller within the unidirectional ring cavity and are very stable. A chirped-grating-based true-time-delay system using the proposed laser source is constructed and demonstrated experimentally.