Formation of γ-Fe2O3 nanoparticles and vacancy ordering: An in situ X-ray powder diffraction study

The formation of maghemite, γ-Fe₂O₃ nanoparticles has been studied by in situ X-ray powder diffraction. The maghemite was formed by thermal decomposition of an amorphous precursor compound made by reacting lauric acid, CH₃(CH₂)₁₀COOH with Fe(NO₃)₃·9H₂O. It has been shown that cubic γ-Fe₂O₃ was formed directly from the amorphous precursor and that vacancy ordering starts about 45 min later at 305 °C resulting in a tripled unit cell along the c-axis. The kinetics of grain growth was found to obey a power law with growth exponents n equal to 0.136(6) and 0.103(5) at 305 and 340 °C, respectively. Particles with average sizes of 12 and 13 nm were obtained in 86 and 76 min at 305 and 340 °C, respectively. The structure of cubic and vacancy ordered phases of γ-Fe₂O₃ was studied at 305 °C by Rietveld refinements.     

Elucidation of methyl tert-butyl ether degradation with Fe/H2O2 by purge-and-trap gas chromatography-mass spectrometry

Degradation of methyl tert-butyl ether (MTBE) with Fe²⁺/H₂O₂ was studied by purge-and-trap gas chromatography-mass spectrometry. MTBE was degraded 99% within 120 min under optimum conditions. MTBE was firstly degraded rapidly based on a Fe²⁺/H₂O₂ reaction and then relatively slower based on a Fe³⁺/H₂O₂ reaction. The dissolved oxygen decreased rapidly in the Fe²⁺/H₂O₂ reaction stage, but showed a slow increase in the Fe³⁺/H₂O₂ reaction stage. tert-Butyl formate, tert-butyl alcohol, methyl acetate and acetone were identified as primary degradation products by mass spectrometry. A preliminary reaction mechanism involving two different pathways for the degradation of MTBE with Fe²⁺/H₂O₂ was proposed. This study suggests that degradation of MTBE can be achieved using the Fe²⁺/H₂O₂ process.     

On the conformational characteristics of the O,O,O-trimethyl selenophosphate molecule

Spectroscopic and theoretical studies were carried out for O,O,O-trimethyl selenophosphate molecule. DFT structural and vibrational calculations were performed at 6-311++G^∗∗ level. Ar/matrix-FTIR spectra were recorded. A coexistence of different conformers with C₃ and C₁ symmetries was detected at different temperatures. Spectral evidence of a lower energy C_s conformer was found. These conclusions are consistent with the results from DFT calculations. A tentative assignment of the features observed in the Ar/matrix-FTIR spectra is proposed.     

Copper(I) catalysis: Synthesis of N,N′-diarylated and N-aryl,N′-formylated chiral C2-symmetric diamines

Chiral N,N′-diaryl C₂-symmetric diamines and N-aryl,N′-formyl-trans-(1R,2R)-diaminocyclohexane are readily accessed by copper catalyzed N,N′-diarylation and N-aryl,N′-formylation of trans-(1R,2R)-diaminocyclohexane with aryl bromides. N,N′-diarylation using (R)-1,1′-binaphthyl-2,2′-diamine and iodobenzene gave the corresponding (R)-N,N′-diphenyl-1,1′-binaphthyl-2,2′-diamine derivative in 83% yield.     

Polyphosphoric acid supported on silica-coated NiFe2O4 nanoparticles: An efficient and magnetically-recoverable catalyst for N-formylation of amines

A rapid, green and simple method for the N-formylation of various aromatic amines with formic acid using polyphosphoric acid supported on silica-coated NiFe₂O₄ magnetic nanoparticles (NiFe₂O₄@SiO₂–PPA) under solvent-free conditions at room temperature has been developed. The magnetic catalyst can be easily removed by a simple magnet and reused at least three times without any loss of its high catalytic activity. In addition to its facility, this protocol enhances product purity and promises economic and also environmental profits.     

I2-mediated C3-formylation of indoles by tertiary amine and H2O

An I₂-promoted 3-formylation of free (N–H) and N-substituted indoles with tetramethylethylenediamine (TMEDA) and H₂O as the carbonyl source is achieved, providing 3-formylindole in moderate to excellent yields with good functional group tolerance. This procedure represents an exceedingly attractive alternative to the traditional formylation methods.     

Synthesis and characterization of n=5, 6 members of the La4Srn−4TinO3n+2 series with layered structure based upon perovskite

Layered compounds have been synthesized and structurally characterized for the n=5 and 6 members of the perovskite-related family La₄Sr_n−4Ti_nO_3n+2 by combining X-ray diffraction and transmission electron microscopy. Their structure can be regarded as comprising [(La,Sr)₅Ti₅O₁₇] and [(La,Sr)₆Ti₆O₂₀] perovskite blocks joined by crystallographic shears along the a-axis, with consecutive blocks shifted by 1/2 [100]_p. The n=5 member is similar to the previously reported n=5 member of other A_nB_nO_3n+2-related series. The n=6 member, which has only been briefly reported in other systems previously, is also a well-behaved member of this A_nB_nO_3n+2 series.     

Selective functionalization at the small rim of calix[6]arene. Synthesis of novel non-symmetrical N3, N4 and N3ArO biomimetic ligands

Eight novel calix[6]arene-based biomimetic ligands for transition metal ions have been synthesized. They display a non-symmetrical N₃, N₄ or N₃ArO binding core that mimics enzyme active sites presenting histidine and tyrosine residues. The key step for their synthesis is the mono-alkylation at the small rim of the C_3v symmetrical trimethyl ether derivative of tBu-calix[6]arene with N-Boc-2-chloroethylamine to yield a novel calix[6]arene synthon. Its combined O-alkylation with a chloromethyl aromatic amine and N-deprotection or alkylation or reductive alkylation with a salicylaldehyde derivative yielded the calix[6]arene-based ligands with mixed N/O donors.     

Synthesis, Characterization, and Conductivity Studies of Poly-o-Methoxyaniline Intercalated into V2O5 Xerogel

In this work we study the conductivity properties of poly-o-methoxyaniline/V₂O₅ intercalation compounds obtained through intercalative polymerization of o-methoxyaniline with V₂O₅·nH₂O in hydrogel form and by reacting directly with V₂O₅ film in de-hydrated form (xerogel). These new compounds were characterized using Fourier-transform infrared and ultra-violet/visible spectroscopies, electron paramagnetic resonance, elemental analysis (C, N, H), thermogravimetric analysis, scanning electron microscopy, dc-conductivity and powder X-ray diffraction. For samples formed from V₂O₅ xerogel in film form, an increase in dc-conductivity and a decrease in the thermal activation energy in comparison with pure matrix was observed. The increase in conductivity is attributed to an increase of carrier density in the vanadium oxide lattice and the contribution of polarons from the polymer. On the other hand, for the intercalation compound obtained with V₂O₅·nH₂O in hydrogel form presents a very low room temperature conductivity value. The decrease in conductivity is due to the lack of connectivity of the various parts that compose the material.     

Cation ordering in the fluorite-like transparent conductors In4+xSn3−2xSbxO12 and In6TeO12

The cation ordering in the fluorite-like transparent conductors In_4+xSn_3−2xSb_xO₁₂ and In₆TeO₁₂, was investigated by Time of Flight Neutron Powder Diffraction and X-ray Powder Diffraction (tellurate). The structural results including atomic positions, cation distributions, metal-oxygen distances and metal-oxygen-metal angles point to a progressive cation ordering on both sites of the Tb₇O₁₂-type structure with a strong preference of the smaller 4d¹⁰ cations (Sn⁴⁺, Sb⁵⁺, Te⁶⁺) for the octahedral sites. The corresponding increase of the overall structure-bonding anisotropy is analyzed in terms of the crystal chemical properties of the OM₄ tetrahedral network of the antistructure. The relationships between the M₇O₁₂ and the M₂O₃ bixbyite-type structures are explored. Within the whole series of compositions In_4+xM_3−xO₁₂ (M=Sn, Sb, Te) there exists an increase of the symmetry gap between the more symmetrical bixbyite structure and the M₇O₁₂ type. This is tentatively correlated with the progressive weakening of thermal stability of these compositions from Sn to Te via Sb.     

Y(OTf)3 as a highly efficient catalyst in Ferrier Rearrangement for the synthesis of O- and S-2,3-unsaturated glycopyranosides

By using Y(OTf)₃ as the catalyst, a series of 2,3-unsaturated-glucosides have been synthesized from 3,4,6-tri-O-acetyl-d-glucal, 3,4-di-O-acetyl-l-rhamnal, and 3,4,6-tri-O-benzyl-d-glucal under mild reaction conditions in good yields with high anomeric selectivities. It was found that, in this reaction, 3,4,6-tri-O-benzyl-d-glucal behaved differently from the other two glucals when it was reacted with phenol, O-benzyl glucoside instead of O-phenyl glucoside formed as the sole product. An explanation is given for this phenomenon.     

Effect of heat treatment on the structure of L-Ta2O5:: a study by XRPD and HRTEM methods

The effect of heat treatment on the structure of L-Ta₂O₅ has been studied by X-ray powder diffraction and high-resolution transmission electron microscopy, complemented by density measurements. Two stable low-temperature forms of L-Ta₂O₅ were found: one below about 1000°C with a b^* multiplicity of m≈13.5 and the other at 1350°C with m=11. The former modification was disordered, containing defects and twins, while the latter seemed to be more ordered. At intermediate temperatures, ordered and disordered mixtures of L-Ta₂O₅ slabs with m values in the range m=11-14 were seen. A new model of a structure of L-Ta₂O₅ (m=11) is proposed. The model can be described as an ordered intergrowth of slabs of α-U₃O₈ and β-U₃O₈ types. The α-U₃O₈ slabs are wider and contain somewhat larger three-sided tunnels that appear to be more suitable for interstitial Ta atoms than the β-U₃O₈ slabs. The density measurements confirm that additional Ta atoms are present in the structure.     

Synthesis, structure and physical properties of Ru ferrites: BaMRu5O11 (M=Li and Cu) and BaM′2Ru4O11 (M′=Mn, Fe and Co)

The synthesis, structure, and physical properties of five R-type Ru ferrites with chemical formula BaMRu₅O₁₁ (M=Li and Cu) and BaM′₂Ru₄O₁₁ (M′=Mn, Fe and Co) are reported. All the ferrites crystallize in space group P6₃/mmc and consist of layers of edge sharing octahedra interconnected by pairs of face sharing octahedra and isolated trigonal bipyramids. For M=Li and Cu, the ferrites are paramagnetic metals with the M atoms found on the trigonal bipyramid sites exclusively. For M′=Mn, Fe and Co, the ferrites are soft ferromagnetic metals. For M′=Mn, the Mn atoms are mixed randomly with Ru atoms on different sites. The magnetic structure for BaMn₂Ru₄O₁₁ is reported.     

Structure and magnetic order in the series BixRE1−xFe0.5Mn0.5O3 (RE=La,Nd)

The influence of Bi³⁺ on the structural and magnetic properties of the rare-earth-containing perovskites REFe_0.5Mn_0.5O₃ (RE=La,Nd) was studied, and the limit of bismuth substitution was determined to be x≤0.5 in Bi_xRE_1−xFe_0.5Mn_0.5O_3+δ (RE=La,Nd) at ambient pressure. Crystal structures in both La and Nd series were determined to be GdFeO₃-type Pnma with the exception of the Bi_0.3La_0.7Fe_0.5Mn_0.5O₃ sample, which is monoclinic I2/a in the a⁻b⁻b⁻ tilt scheme. The samples undergo a transition to G-type antiferromagnetic order along with a weak ferromagnetic component, mixed with cluster-glass type behavior. The substitution of bismuth into the lattice results in a drop in T_N relative to the lanthanide end-members. Long range ordering temperatures T_N in the range 240-255 K were observed, with a significantly lower ordered magnetic moment in the case of lanthanum (M∼1.7-1.9 μ_B) than in the case of neodymium (M∼2.1 μ_B).     

Synthesis, Characterization and Humidity Sensitive Properties of Nanocrystalline LaCoxFe1-xO3

The nanocrystalline LaCo_xFe_1-xO₃ with different concentrations of Co was prepared by polyethylene glycol (PEG) sol-gel method and characterized by differential thermal analysis and thermal gravimetric analysis (DTA-TGA), X-ray diffraction (XRD), and scanning electron microscope (SEM). It was found that the crystal structure of perovskite-type could be obtained at 600 °C, and the concentration of Co had significant effects on the solid-state reaction and the average particle size of the obtained nanocrystals. Furthermore, the humidity-sensitive properties of nanocrystalline LaCo_xFe_1-xO₃ were investigated, and it was found that LaCo_0.3Fe_0.7O₃ exhibited higher sensitivity to humidity compared with other samples. The addition of Na₂CO₃ improved the humidity-sensitive properties of this sample, and made its response to humidity good in the whole humidity range of 11%-95% relative humidity (RH).     

Dielectric properties of some MM′O4 and MTiM′O6 (M=Cr, Fe, Ga; M′=Nb, Ta, Sb) rutile-type oxides

We describe an investigation of the structure and dielectric properties of MM′O₄ and MTiM′O₆ rutile-type oxides for M=Cr, Fe, Ga and M′=Nb, Ta and Sb. All the oxides adopt a disordered rutile structure (P4₂/mnm) at ambient temperature. A partial ordered trirutile-type structure is confirmed for FeTaO₄ from the low temperature (17 K) neutron diffraction studies. While both the MM′O₄ oxides (CrTaO₄ and FeTaO₄) investigated show a normal dielectric property MTiM′O₆ oxides for M=Fe, Cr and M′=Nb/Ta/Sb display a distinct relaxor/relaxor-like response. Significantly the corresponding gallium analogs, GaTiNbO₆ and GaTiTaO₆, do not show a relaxor response at T<500 K.     

Phase equilibria and crystal chemistry of the R-Cu-Ti-O systems (R=lanthanides and Y)

As part of the study of interaction of the Ba₂RCu₃O_6+z (R=lanthanides and Y) superconductor with SrTiO₃ buffer, phase equilibria of the subsystem, R₂O₃-TiO₂-CuO (R=Nd, Y, and Yb), have been investigated in air at 960 °C. While the phase relationships of the two phase diagrams with smaller R (Y and Yb) are similar, substantial differences were found in the Nd₂O₃-TiO₂-CuO system, partly due to different phase formation in the binary R₂O₃-TiO₂ and R₂O₃-CuO systems. R₂CuTiO₆ and R₂Cu₉Ti₁₂O₃₆ were the only ternary phases established in all the three diagrams. R₂Cu₉Ti₁₂O₃₆ belongs to the perovskite-related [AC₃](B₄)O₁₂ family which is cubic Im3. Depending on the size of R³⁺, R₂CuTiO₆ crystallizes in two crystal systems: Pnma (R=La-Gd), and P6₃cm (R=Dy-Lu). The structure and crystal chemistry of the Pnma series of R₂CuTiO₆ (R=La, Nd, Sm, Eu, and Gd) are discussed in detail in this paper. Patterns for selected members of R₂CuTiO₆ have also been prepared and submitted for inclusion in the Powder Diffraction File (PDF).     

Ab initio study on structure and phase transition of A- and B-type rare-earth sesquioxides Ln2O3 (Ln=La-Lu, Y, and Sc) based on density function theory

Ab initio energetic calculations based on the density functional theory (DFT) and projector augmented wave (PAW) pseudo-potentials method were performanced to determine the crystal structural parameters and phase transition data of the polymorphic rare-earth sesquioxides Ln₂O₃ (where Ln=La-Lu, Y, and Sc) with A-type (hexagonal) and B-type (monoclinic) configurations at ground state. The calculated results agree well with the limited experimental data and the critically assessed results. A set of systematic and self-consistent crystal structural parameters, energies and pressures of the phase transition were established for the whole series of the A- and B-type rare-earth sesquioxides Ln₂O₃. With the increase of the atomic number, the ionic radii of rare-earth elements Ln and the volumes of the sesquioxides Ln₂O₃ reflect the so-called “lanthanide contraction”. With the increase of the Ln³⁺-cation radius, the bulk modulus of Ln₂O₃ decreases and the polymorphic structures show a degenerative tendency.     

Magnetic diphase nanostructure of ZnFe2O4/γ-Fe2O3

Magnetic diphase nanostructures of ZnFe₂O₄/γ-Fe₂O₃ were synthesized by a solvothermal method. The formation reactions were optimized by tuning the initial molar ratios of Fe/Zn. All samples were characterized by X-ray diffraction, thermogravimetric analysis, infrared spectroscopy, and Raman spectra. It is found that when the initial molar ratio of Fe/Zn is larger than 2, a diphase magnetic nanostructure of ZnFe₂O₄/γ-Fe₂O₃ was formed, in which the presence of ZnFe₂O₄ enhanced the thermal stability of γ-Fe₂O₃. Further increasing the initial molar ratio of Fe/Zn larger than 6 destabilized the diphase nanostructure and yielded traces of secondary phase α-Fe₂O₃. The grain surfaces of diphase nanostructure exhibited a spin-glass-like structure. At room temperature, all diphase nanostructures are superparamagnetic with saturation magnetization being increased with γ-Fe₂O₃ content.     

Enzyme mimics of spinel-type CoxNi1−xFe2O4 magnetic nanomaterial for eletroctrocatalytic oxidation of hydrogen peroxide

A series of spinel-type Co_xNi_1−xFe₂O₄ (x = 0, 0.2, 0.4, 0.5, 0.6, 0.8, 1.0) magnetic nanomaterials were solvothermally synthesized as enzyme mimics for the eletroctrocatalytic oxidation of H₂O₂. X-ray diffraction and scanning electron microscope were employed to characterize the composition, structure and morphology of the material. The electrochemical properties of spinel-type Co_xNi_1−xFe₂O₄ with different (Co/Ni) molar ratio toward H₂O₂ oxidation were investigated, and the results demonstrated that Co_0.5Ni_0.5Fe₂O₄ modified carbon paste electrode (Co_0.5Ni_0.5Fe₂O₄/CPE) possessed the best electrocatalytic activity for H₂O₂ oxidation. Under optimum conditions, the calibration curve for H₂O₂ determination on Co_0.5Ni_0.5Fe₂O₄/CPE was linear in a wide range of 1.0 × 10⁻⁸–1.0 × 10⁻³ M with low detection limit of 3.0 × 10⁻⁹ M (S/N = 3). The proposed Co_0.5Ni_0.5Fe₂O₄/CPE was also applied to the determination of H₂O₂ in commercial toothpastes with satisfactory results, indicating that Co_xNi_1−xFe₂O₄ is a promising hydrogen peroxidase mimics for the detection of H₂O₂.