Photoluminescence of Si from Si nanocrystal-doped SiO2/Si multilayered sample

A multilayered Si nanocrystal-doped SiO₂/Si (or Si-nc:SiO₂/Si) sample structure is studied to acquire strong photoluminescence (PL) emission of Si via modulating excess Si concentration. The Si-nc:SiO₂ results from SiO thin film after thermal annealing. The total thickness of SiO layer remains 150 nm, and is partitioned equally into a number of sublayers (N = 3, 5, 10, or 30) by Si interlayers. For each N-layered sample, a maximal PL intensity of Si can be obtained via optimizing the thickness of Si interlayer (or d_Si). This maximal PL intensity varies with N, but the ratio of Si to O is nearly a constant. The brightest sample is found to be that of N = 10 and d_Si = 1 nm, whose PL intensity is ∼5 times that of N = 1 without additional Si doping, and ∼2.5 times that of Si-nc:SiO₂ prepared by co-evaporating of SiO and Si at the same optimized ratio of Si to O. Discussions are made based on PL, TEM, EDX and reflectance measurements.     

The interface reaction of high-k La2Hf2O7/Si thin film grown by pulsed laser deposition

The La₂Hf₂O₇ films have been deposited on Si (1 0 0) substrate by using pulsed laser deposition (PLD) method. X-ray diffraction (XRD) demonstrates that the as-grown film is amorphous and crystallizes after 1000 °C annealing. The interface structure is systematically studied by Synchrotron X-ray reflectivity (XRR), Fourier transform infrared (FTIR) and X-ray photoelectron spectroscopy (XPS). Silicide, silicate and SiO_x formations from interfacial reaction are observed on the surface of the Si substrate in the as-grown film. The impact of silicide formation on the electrical properties is revealed by capacitance-voltage (C-V) measurements. By post-deposition annealing (PDA), silicide can be effectively eliminated and C-V property is obviously improved.     

Structural, microstructural and magnetic properties of NiFe2O4, CoFe2O4 and MnFe2O4 nanoferrite thin films

The structural, microstructural and magnetic properties of nanoferrite NiFe₂O₄ (NF), CoFe₂O₄ (CF) and MnFe₂O₄ (MF) thin films have been studied. The coating solution of these ferrite films was prepared by a chemical synthesis route called sol-gel combined metallo-organic decomposition method. The solution was coated on Si substrate by spin coating and annealed at 700 °C for 3 h. X-ray diffraction pattern has been used to analyze the phase structure and lattice parameters. The scanning electron microscopy (SEM) and atomic force microscopy (AFM) have been used to show the nanostructural behavior of these ferrites. The values of average grain's size from SEM are 44, 60 and 74 nm, and from AFM are 46, 61 and 75 nm, respectively, measured for NF, CF and MF ferrites. At room temperature, the values of saturation magnetization, M_s∼50.60, 33.52 and 5.40 emu/cc, and remanent magnetization, M_r∼14.33, 15.50 and 1.10 emu/cc, respectively, are observed for NF, CF and MF. At low temperature measurements of 10 K, the anisotropy of ferromagnetism is observed in these ferrite films. The superparamagnetic/paramagnetic behavior is also confirmed by χ′(T) curves of AC susceptibility by applying DC magnetizing field of 3 Oe. The temperature dependent magnetization measurements show the magnetic phase transition temperature.     

Spray-pyrolysis deposition of LaMnO3 and La1−xCaxMnO3 thin films

Ethylene glycol solutions of La-Mn(II) and La-Ca-Mn(II) citric complexes has been used as a starting material for spray-pyrolysis deposition of LaMnO₃ and La_1−xCa_xMnO₃ thin films on β-quartz, fused quartz, Si(0 0 1) and SrTiO₃(1 0 0) substrates heated during the deposition at 380 °C. At suitable post-deposition heating conditions highly uniform films, 0.1-1 μm in thickness, with good crystal structure were obtained. Highly textured LaMnO₃ films are obtained on SrTiO₃(1 0 0) substrate. Interaction between the layer and Si-containing substrates is observed during the post-deposition heating in static air.     

Structural and electrical properties of (Na0.85K0.15)0.5Bi0.5TiO3 thin films deposited on LaNiO3 and Pt bottom electrodes

(Na_0.85K_0.15)_0.5Bi_0.5TiO₃ thin films were deposited on LaNiO₃(LNO)/SiO₂/Si(1 0 0) and Pt/Ti/SiO₂/Si(1 0 0) substrates by metal-organic decomposition, and the effects of bottom electrodes LNO and Pt on the ferroelectric, dielectric and piezoelectric properties were investigated by ferroelectric tester, impedance analyzer and scanning probe microscopy, respectively. For the thin films deposited on LNO and Pt electrodes, the remnant polarization 2P_r are about 22.6 and 8.8 μC/cm² under 375 kV/cm, the dielectric constants 238 and 579 at 10 kHz, the dielectric losses 0.06 and 0.30 at 10 kHz, the statistic d_33eff values 95 and 81 pm/V. The improved piezoelectric properties could make (Na_1−xK_x)_0.5Bi_0.5TiO₃ thin film as a promising candidate for piezoelectric thin film devices.     

Infrared optical properties of Ba(Zr0.20Ti0.80)O3 and Ba(Zr0.30Ti0.70)O3 thin films prepared by sol-gel method

Ba(Zr_xTi_1−x)O₃ (BZT) (x = 0.20 and 0.30) thin films are deposited on Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrate by sol-gel method. X-ray diffraction patterns show that the thin films have a good crystallinity. Optical properties of the films in the wavelength range of 2.5-12 μm are studied by infrared spectroscopic ellipsometry (IRSE). The optical constants of the BZT thin films are determined by fitting the IRSE data using a classical dispersion formula. As the wavelength increases, the refractive index decreases, while the extinction coefficients increase. The effective static ionic charges are derived, which are smaller than that in a purely ionic material for the BZT thin films.     

Ultra-thin Si overlayers on the TiO2 (1 1 0)-(1 × 2) surface: Growth mode and electronic properties

The growth of thin subnanometric silicon films on TiO₂ (1 1 0)-(1 × 2) reconstructed surfaces at room temperature (RT) has been studied in situ by X-ray and ultra-violet photoelectron spectroscopies (XPS and UPS), Auger electron and electron-energy-loss spectroscopies (AES and ELS), quantitative low energy electron diffraction (LEED-IV), and scanning tunneling microscopy (STM). For Si coverage up to one monolayer, a heterogeneous layer is formed. Its composition consists of a mixture of different suboxides SiO_x (1 < x ? 2) on top of a further reduced TiO₂ surface. Upon Si coverage, the characteristic (1 × 2) LEED pattern from the substrate is completely attenuated, indicating absence of long-range order. Annealing the SiO_x overlayer results in the formation of suboxides with different stoichiometry. The LEED pattern recovers the characteristic TiO₂ (1 1 0)-(1 × 2) diagram. LEED I-V curves from both, substrate and overlayer, indicate the formation of nanometric sized SiO_x clusters.     

Growth of ultra-thin TiO2 films by spray pyrolysis on different substrates

In the present study TiO₂ films were deposited by spray pyrolysis method onto ITO covered glass and Si (1 0 0) substrates. The spray solution containing titanium(IV) isopropoxide, acetylacetone and ethanol was sprayed at a substrate temperature of 450 °C employing 1-125 spray pulses (1 s spray and 30 s pause). According to AFM, continuous coverage of ITO and Si substrates with TiO₂ layer is formed by 5-10 and below 5 spray pulses, respectively. XPS studies revealed that TiO₂ film growth on Si substrate using up to 4 spray pulses follows 2D or layer-by-layer-growth. Above 4 spray pulses, 3D or island growth becomes dominant irrespective of the substrate. Only 50 spray pulses result in TiO₂ layer with the thickness more than XPS measurement escape depth as any signal from the substrate could not be detected. TiO₂ grain size remains 30 nm on ITO and increases from 10-20 nm to 50-100 nm on Si substrate with the number of spray pulses from 1 to 125.     

Effect of thickness on the structure, morphology and optical properties of sputter deposited Nb2O5 films

Nb₂O₅ films with the thickness (d) ranging from 55 to 2900 nm were deposited on BK-7 substrates at room temperature by a low frequency reactive magnetron sputtering system. The structure, morphology and optical properties of the films were investigated by X-ray diffraction, atomic force microscopy and spectrophotometer, respectively. The experimental results indicated that the thickness affects drastically the structure, morphology and optical properties of the film. There exists a critical thickness of the film, d_cri =2010 nm. The structure of the film remains amorphous as d < d_cri. However, it becomes crystallized as d > d_cri. The root mean square of surface roughness increases with increasing thickness as d > 1080 nm. Widths and depths of the holes on film surface increase monotonously with increasing thickness, and widths of the holes are larger than 1000 nm for the crystalline films. Refractive index increases with increasing thickness as d < d_cri, while it decreases with increasing thickness as d > d_cri. In addition, the extinction coefficient increases with increasing thickness as d > d_cri.     

Structural and magnetoresistive properties of half metallic Co2Mn1−xSi thin films

Polycrystalline Co₂Mn_1−xSi (CMS) thin films with Mn-deficiency can grow on different types of substrates such as MgO (1 0 0) single crystal, α-sapphire (0 0 0 1) and Si coated with SiO₂ either by using V or Ta/Cu as the seed layer. The magnetic property, especially the coercivity of the CMS thin films strongly depends on the crystalline structure and microstructure of the CMS thin film, hence it is affected by the substrate and also the seed layer. Very soft CMS thin film with coercivity of about 20 Oe has been obtained when MgO (1 0 0) is used as the substrate. Magnetic tunnel junctions (with MR ratio of about 9%–18%) by utilizing the CMS as one of ferromagnetic electrodes have been successfully fabricated. The degradation of the magnetoresistive effect of the MTJ after magnetic annealing is attributed to the diffusion of the Mn-atoms into the tunnel barrier during the annealing process.     

The ferroelectric and ferromagnetic characterization of CoFe2O4/Pb(Mg1/3Nb2/3)O3-PbTiO3 multilayered thin films

The multiferroic (PMN-PT/CFO)_n (n = 1,2) multilayered thin films have been prepared on SiO₂/Si(1 0 0) substrate with LNO as buffer layer via a rf magnetron sputtering method. The structure and surface morphology of multilayered thin films were determined by X-ray diffraction (XRD) and atom force microscopy (AFM), respectively. The smooth, dense and crack-free surface shows the excellent crystal quality with root-mean-square (RMS) roughness only 2.9 nm, and average grain size of CFO thin films on the surface is about 44 nm. The influence of the thin films thickness size, periodicity n and crystallite orientation on their properties including ferroelectric, ferromagnetic properties in the (PMN-PT/CFO)_n multilayered thin films were investigated. For multilayered thin films with n = 1 and n = 2, the remanent polarization Pr are 17.9 μC/cm² and 9.9 μC/cm²; the coercivity H_c are 1044 Oe and 660 Oe, respectively. In addition, the relative mechanism are also discussed.     

An XPS study and electrical properties of Pb1.1Zr0.53Ti0.47O3/PbO/Si (MFIS) structures according to the substrate temperature of the PbO buffer layer

PbO and PZT thin films were deposited on the p-type (1 0 0) Si substrate by the rf magnetron sputtering method with PbO and Pb_1.1Zr_0.53Ti_0.47O₃ targets for the application of the metal-ferroelectric-insulator-semiconductor (MFIS) structure. The MFIS structures with the PbO buffer layer show the good electric properties including a high memory window and a low leakage current density. The maximum value of the memory window is 2.0 V under the applied voltage of 9 V for the Pt/PZT (200 nm, 400 °C)/PbO (80 nm)/Si structures with the PbO buffer layer deposited at the substrate temperature of 300 °C. From the X-ray photoelectron spectroscopy (XPS) results, we could confirm that the substrate temperature of PbO affects the chemical states of the interface between the PbO buffer layer and Si substrate, which results in the inter-diffusion of Pb and the formation of the intermediate phases (PbSiO₃). And the existence of the undesired SiO₂ layer, which is the low dielectric layer, was confirmed at the surface region of the Si substrate by the XPS depth profile analysis.     

Substrate effect on electronic sputtering yield in polycrystalline fluoride (LiF, CaF2 and BaF2) thin films

Influence of substrate on electronic sputtering of fluoride (LiF, CaF₂ and BaF₂) thin films, 10 and 100 nm thin, under dense electronic excitation of 120 MeV Ag²⁵⁺ ions irradiation is investigated. The sputtering yield of the films deposited on insulating (glass) and semiconducting (Si) substrates are determined by elastic recoil detection analysis technique. Results revealed that sputtering yield is higher, up to 7.4 × 10⁶ atoms/ion for LiF film on glass substrate, than that is reported for bulk materials/crystals (∼10⁴ atoms/ion), while a lower value of the yield (2.3 × 10⁶ atoms/ion) is observed for film deposited on Si substrate. The increase in the yield for thin films as compared to bulk material is a combined effect of the insulator substrate used for deposition and reduced film dimension. The results are explained in the framework of thermal spike model along with substrate and size effects in thin films. It is also observed that the material with higher band gap showed higher sputtering yield.     

Structural, electrical and piezoelectric properties of LiNbO3 thin films for surface acoustic wave resonators applications

In this work, 0.30 μm thick LiNbO₃ layers have been deposited by sputtering on nanocrystalline diamond/Si and platinised Si substrates. The films were then analyzed in terms of their structural and optical properties. Crystalline orientations along the (0 1 2), (1 0 4) and (1 1 0) axes have been detected after thermal treatment at 500 °C in air. The films were near-stoichiometric and did not reveal strong losses or diffusion in lithium during deposition or after thermal annealing. Pronounced decrease of the roughness on top of the LiNbO₃ layer and at the interface between LiNbO₃ and diamond was also observed after annealing, compared to the bare nanocrystalline diamond on Si substrate. Furthermore, ellipsometry analysis showed a better density and a reduced thickness of the surface layer after post-deposition annealing. The dielectric constant and losses have been measured to 50 and less than 3.5%, respectively, for metal/insulator/metal structures with 0.30 μm thick LiNbO₃ layer. The piezoelectric coefficient d₃₃ was found to be 7.1 pm/V. Finally, we succeeded in switching local domain under various positive and negative voltages.     

Formation of silicon nanodots from dysprosium-doped amorphous SiCxOy films grown by hot-filament assisted chemical vapor deposition of CH3SiH3 and Dy(DPM)3 gas jets

We report on Si nanodot formation by chemical vapor deposition (CVD) of ultrathin films and following oxidation. The film growth was carried out by hot-filament assisted CVD of CH₃SiH₃ and Dy(DPM)₃ gas jets at the substrate temperature of 600 °C. The transmission electron microscopy observation and X-ray photoelectron spectroscopy analysis indicated that ∼35 nm Dy-doped amorphous silicon oxycarbide (SiC_xO_y) films were grown on Si(1 0 0). The Dy concentration was 10-20% throughout the film. By further oxidation at 860 °C, the smooth amorphous film was changed to a rough structure composed of crystalline Si nanodots surrounded by heavily Dy-doped SiO₂.     

Formation of Co ultrathin films on Si(1 1 1): Growth mechanisms, electronic structure and transport

The AES, EELS, AFM and resistance measurement investigations have been performed to determine the growth mechanism, electronic structure and resistance-thickness dependence of Co layers on silicon at the thickness range from submonolayer up to several monolayer coverage. These layers were obtained under UHV high-rate deposition with using re-evaporation of Co from a Ta foil. The layer-by-layer growth of Co on Si(1 1 1) with some light segregation of Si has been found on the AES data. An enlarged and reduced concentration of valence electrons in the interface Si layer at the thickness ranges 0-1 Å and in the Co film at d = 1-2 Å has been observed. Resistance measurement of the Co film showed a fast decrease of the resistance down to some value limited by quantum-size effect in accordance with the formation of a two-dimensional Co phase at d = 1-2 Å.     

CO2 adsorption on Cr(1 1 0) and Cr2O3(0 0 0 1)/Cr(1 1 0)

We attempt to correlate qualitatively the surface structure with the chemical activity for a metal surface, Cr(1 1 0), and one of its surface oxides, Cr₂O₃(0 0 0 1)/Cr(1 1 0). The kinetics and dynamics of CO₂ adsorption have been studied by low energy electron diffraction (LEED), Aug er electron spectroscopy (AES), and thermal desorption spectroscopy (TDS), as well as adsorption probability measurements conducted for impact energies of E_i = 0.1-1.1 eV and adsorption temperatures of T_s = 92-135 K. The Cr(1 1 0) surface is characterized by a square shaped LEED pattern, contamination free Cr AES, and a single dominant TDS peak (binding energy E_d = 33.3 kJ/mol, first order pre-exponential 1 × 10¹³ s⁻¹). The oxide exhibits a hexagonal shaped LEED pattern, Cr AES with an additional O-line, and two TDS peaks (E_d = 39.5 and 30.5 kJ/mol). The initial adsorption probability, S₀, is independent of T_s for both systems and decreases exponentially from 0.69 to 0.22 for Cr(1 1 0) with increasing E_i, with S₀ smaller by ∼0.15 for the surface oxide. The coverage dependence of the adsorption probability, S(Θ), at low E_i is approx. independent of coverage (Kisliuk-shape) and increases initially at large E_i with coverage (adsorbate-assisted adsorption). CO₂ physisorbs on both systems and the adsorption is non-activated and precursor mediated. Monte Carlo simulations (MCS) have been used to parameterize the beam scattering data. The coverage dependence of E_d has been obtained by means of a Redhead analysis of the TDS curves.     

Preparation of the La0.8Sr0.2MnO3 films on STO and LAO substrates by excimer laser-assisted metal organic deposition using the KrF laser

La_0.8Sr_0.2MnO₃ films were prepared on SrTiO₃ (STO) and LaAlO₃ (LAO) substrates using excimer laser-assisted metal organic deposition (ELAMOD). For the LAO substrate, no epitaxial La_0.8Sr_0.2MnO₃ film was obtained by laser irradiation in the fluence range from 60 to 110 mJ/cm² with heating at 500 °C. On the other hand, an epitaxial La_0.8Sr_0.2MnO₃ film on the STO substrate was formed by laser irradiation in the fluence range from 60 to 100 mJ/cm² with heating at 500 °C. To optimize the electrical properties for an IR sensor, the effects of the laser fluence, the irradiation time and the film thickness on the temperature dependence of the resistance and temperature coefficient of resistance (TCR: defined as 1/R·(dR/dT)) of the LSMO films were investigated. An LSMO film on the STO substrate that showed the maximum TCR of 3.9% at 265 K was obtained by the ELAMOD process using the KrF laser.     

The interfacial properties of MgCl2 films grown on a flat SiO2/Si substrate. An XPS and ISS study

The interaction between MgCl₂ and SiO₂ was investigated by X-ray photoelectron spectroscopy (XPS), ion scattering spectroscopy (ISS) and contact potential difference (CPD) measurements. A thin SiO₂ layer was grown for this purpose on a Si(1 0 0) wafer and MgCl₂ was applied on this support at room temperature by evaporation under UHV conditions. It was found that magnesium chloride is deposited molecularly on the SiO₂ substrate, growing in layers and covering uniformly the oxide surface. The interaction with the substrate is initially very weak and limited to the interfacial layer. Above 623 K, most of the molecular MgCl₂ is re-evaporated and the interfacial interaction becomes stronger, as Mg-Cl bonds in the remaining sub-monolayer chloride break and Cl atoms desorb. This leaves on the surface sub-stoichiometric MgCl_x, which interacts with oxygen atoms from the substrate to form a complex surface species. At 973 K all Cl atoms desorb and Mg remains on the surface in the form of an oxide.