Poly(dimethylsiloxane) microchip capillary electrophoresis with electrochemical detection for rapid measurement of acetaminophen and its hydrolysate

Poly(dimethylsiloxane) microchip capillary electrophoresis with amperometric detection has been used for rapid separation and determination of acetaminophen and its hydrolysate, i.e. p-aminophenol. A Pt ultramicroelectrode with a diameter of 10 m positioned at the outlet of the separation channel was used as a working electrode for amperometric detection. Factors influencing separation and detection were investigated and optimized. Results show that acetaminophen and p-aminophenol can be well separated within 35 s with RSD<1% for migration time and <7% for detection current for both analytes. Detection limits for both analytes are estimated to be 5.0 mol L^–1 (approximately 0.1 fmol) at S/N=3. This method has been successfully applied to the detection of traces of p-aminophenol in paracetamol tablets.     

Electrokinetic control of fluid in plastified laser-printed poly(ethylene terephthalate)-toner microchips

The application of plastified laser-printed poly(ethylene terephthalate)(PET)-toner microchips to capillary electrophoresis was investigated. Electroosmotic flow was observed in the direction of the cathode for the buffer system studied (phosphate, pH 3–10). Average electroosmotic mobilities of 1.71×10^–4 to 4.35×10^–4 cm² V^–1 s^–1 were observed from pH 3 to 10. This variation suggests that silica fillers in the toner and on the surface of the polymer dominate the zeta potential of the material, which is also confirmed by XPS measurements. Dopamine and catechol were used as model analytes for microchip electrophoresis in combination with electrochemical detection. Results show that these two analytes can be efficiently separated and detected electrochemically with the plastified laser-printed PET-toner microchips.     

Elastic behavior of poly(ethylene terephthalate) chains

The Monte Carlo (MC) method based on the rotational-isomeric-state (RIS) model is adopted in studying the elastic behavior of poly(ethylene terephthalate) (PET) chains in this paper. The mean-square end-to-end distance 〈R²〉, the mean-square radius of gyration 〈S²〉, and the ratio of 〈R²〉/〈S²〉 all increase with elongation ratio λ. The interior conformations are also investigated through calculating the a priori probability of rotational state in the process of tensile elongation. The radius of gyration tensor S is introduced here in order to measure the shape of PET chains, and increases with elongation ratio λ, however, some different behaviors are obtained for . Here , and are the eigenvalues of the radius of gyration tensor . The average energy per repeat unit 〈U〉 and the average free energy per repeat unit 〈A〉 are also calculated, and we find that the average energy decreases with elongation ratio λ, however, the average free energy per repeat unit increases with elongation ratio λ. Elastic force f, energy contribution to force f_U, and entropy contribution to force f_S are also investigated. Both elastic force f and entropy contribution to force f_S increases with λ, however, energy contribution to force f_U and the ratio f_U/f decreases with λ. The ratio of f_U/f is less than zero and almost independent of chain length. The results of these microscopic calculations may explain some macroscopic phenomena of rubber elasticity.     

Conformation of the ground-state dimer in poly(ethylene terephthalate)

Absorbance, excitation, and emission measurements have been performed with methyl benzoate and five model compounds, C₆H₅COO (CH₂)_xOOCC₆H₅, x = 2–6. Under appropriate conditions, three of the model compounds (those with x = 3, 4, 5) show evidence for the formation of intramolecular ground-state dimers. The model compound with x = 5 can form two types of dimers which emit with different energies. The model compound with x = 3 forms one of these dimers, and the model compound with x = 4 prefers the other ground-state dimer. Molecular modeling of the dimers suggests that the two conformations of the ground-state dimers differ in the orientation of the two C?O bonds. In the one dimer these two bonds are nearly parallel, but in the other they make an angle of about 120°. © 1993 John Wiley & Sons, Inc.     

Rapid determination of acetaminophen and p-aminophenol in pharmaceutical formulations using miniaturized capillary electrophoresis with amperometric detection

Capability of fast analysis of a novel miniaturized capillary electrophoresis with carbon disk electrode amperometric detection (mini-CE-AD) system was demonstrated by determining acetaminophen and p-aminophenol in dosage forms. Factors influencing the separation and detection processes were examined and optimized. Under the optimum conditions, the end-capillary 300 μm carbon disc electrode amperometric detector offered favorable signal-to-noise characteristics at a relatively low potential (+600 mV versus Ag/AgCl) for detecting acetaminophen and p-aminophenol. Two analytes can been separated within 150 s in a 8.5 cm length capillary at a separation voltage of 2000 V using a Na₂B₄O₇-KH₂PO₄ running buffer (pH 7.2). Acetaminophen and p-aminophenol could be detected down to the 1.4 × 10⁻⁶-5.9 × 10⁻⁷ mol L⁻¹ level with linearity up to the 1.0 × 10⁻³ mol L⁻¹ level examined. The inter-day repeatability for analytes in peak current (R.S.D. ≤ 2.3%) and migration times (R.S.D. ≤ 1.3%) were excellent. The proposed mini-CE-AD system should find a wide range of analytical applications in pharmaceutical formulations as an alternative to conventional CE and μ-CE.     

Synthesis and characterization of poly(ethylene glycol) methyl ether endcapped poly(ethylene terephthalate)

Linear and branched poly(ethylene terephthalate) (PET) copolymers with polyethylene glycol) (PEG) methyl ether (700 or 2000 g/mol) end groups were synthesized using conventional melt polymerization. DSC analysis demonstrated that low levels of PEG end groups accelerated PET crystallization. The incorporated PEG end groups also decreased the crystallization temperature of PET dramatically, and copolymers with a high content of PEG (>17.6 wt%) were able to crystallize at room temperature. Rheological analysis demonstrated that the presence of PEG end groups effectively decreased the melt viscosities and facilitated melt processing. XPS and ATR-FTIR revealed that the PEG end groups tended to aggregate on the surface, and the surface of compression molded films containing 34.0 wt% PEG were PEG rich (85 wt% PEG). PEG end-capped PET (34.0 wt% PEG) and PET films were immersed into a fibrinogen solution (0.7 mg/mL BSA) for 72 h to investigate the propensity for protein adhesion. XPS demonstrated that the concentration of nitrogen (1.05%) on the surface of PEG endcapped PET film was statistically lower than PET (7.67%). SEM analysis was consistent with XPS results, and revealed the presence of adsorbed protein on the surface of PET films.     

Glycolysis of poly(ethylene terephthalate) (PET) using basic ionic liquids as catalysts

The glycolysis of poly(ethylene terephthalate) (PET) was studied using several ionic liquids and basic ionic liquids as catalysts. The basic ionic liquid, 1-butyl-3-methylimidazolium hydroxyl ([Bmim]OH), exhibits higher catalytic activity for the glycolysis of PET, compared with 1-butyl-3-methylimidazolium bicarbonate ([Bmim]HCO₃), 1-butyl-3-methylimidazolium chloride ([Bmim]Cl) and 1-butyl-3-methylimidazolium bromide ([Bmim]Br). FT-IR, ¹H NMR and DSC were used to confirm the main product of glycolysis was bis(2-hydroxyethyl) terephthalate (BHET) monomer. The influences of experimental parameters, such as the amount of catalyst, glycolysis time, reaction temperature, and dosages of ethylene glycol on the conversion of PET, yield of BHET were investigated. The results showed a strong influence of the mixture evolution of temperature and reaction time on depolymerization of PET. Under the optimum conditions of m(PET):m(EG): 1:10, dosage of [Bmim]OH at 0.1 g (5 wt%), reaction temperature 190 °C and time 2 h, the conversion of PET and the yield of BHET were 100% and 71.2% respectively. Balance between the polymerization of BHET and depolymerization of PET could be changed when the reaction time was more than 2 h and contents of catalyst and EG were changed.     

Surface characterizations of poly(ethylene terephthalate) film modified by a carbohydrate-bearing photoreactive azide group

Grafting of a carbohydrate UV-reactive molecule, the β-d-galactopyranosyl-(1-4)-1-N-[2-(4-azidophenyl amino)-ethylamino]-1-deoxy-d-glucitol (AzPhLac), has been achieved on poly(ethylene terephthalate) film. The dependence of surface density and yield of grafted AzPhLac have been studied versus the number of moles of UV-treated AzPhLac via the deposit of a drop of solution with a known volume and concentration. A nearly complete grafting of initial AzPhLac molecules was reached for the lowest concentration and lowest volume of solution deposit conditions. Grafting density values in the range of 29-181 nmol/cm² confirm the polymeric nature of the grafted layer. FTIR-ATR demonstrated the heterogeneity in thickness of the grafted surface due to the drop-deposit method and solvent evaporation process. AFM (imaging) allowed us to find a correlation between grafting density and rms roughness. Water-contact angle and AFM (contact mode) gave further evidence of the hydrophilic nature of the extreme surface.     

Glycolysis of poly(ethylene terephthalate) catalyzed by ionic liquids

Poly(ethylene terephthalate) (PET) from an industrial manufacturer was depolymerized by ethylene glycol in the presence of a novel catalyst: ionic liquids. It was found that the purification process of the products in the glycolysis catalyzed by ionic liquids was simpler than that catalyzed by traditional compounds, such as metal acetate. Qualitative analysis showed that the main product in the glycolysis process was the bis(hydroxyethyl) terephthalate (BHET) monomer. Thermal analysis of the glycolysis products was carried out by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The influences of experimental parameters, such as the amount of catalyst, glycolysis time, reaction temperature, and water content in the catalyst on the conversion of PET, selectivity of BHET, and distribution of the products were investigated. Results show that reaction temperature is a critical factor in this process. In addition, a detailed reaction mechanism of the glycolysis of PET was proposed.     

WAXS analysis of structural changes of poly(ethylene terephthalate) fibers induced by supercritical-fluid dyeing

 Supercritical CO₂ fluid, a new environmentally friendly dyeing medium, changes the fiber structure to a certain extent in dependence on the treatment temperature and pressure used. Therefore the changes of crystalline structure in poly(ethylene tereph-thalate) (PET) fibers as brought about under the influence of supercritical CO₂ fluid were investigated. For the data collection of wide-angle X-ray diffraction full patterns a two-circle goniometer, equipped with a position sensitive detector, was used. From the observed two-dimensional fiber diffraction patterns the crystallinities of various treated fibers were evaluated. The equatorial scanning yielded the dimensions of crystallites. To elucidate the fiber-surface morphology changes SEM analyses were performed. The supercritical fluid dyeing of PET fibers with highly developed microfibrillar structure under taut-ends conditions promotes changes which are characterized by an increase in crystallinity and by diminution of the apparent crystallite dimensions. Some changes of surface morphology of dyed fibers were observed as well. Received: 14 May 1997 Accepted: 23 September 1997     

Direct usage of products of poly(ethylene terephthalate) glycolysis for manufacturing of glass-fibre-reinforced plastics

The paper reports on the possibility of direct use of some products of poly(ethylene terephthalate) glycolysis, bis(2-hydroxyethyl) terephthalate and ethylene glycol mainly, in the process of glass-fibre-reinforced plastics manufacturing. The addition of toluene diisocyanate as an intermediating agent was an important prerequisite for their incorporation into the resin composition. The composites containing products of poly(ethylene terephthalate) glycolysis up to 15% mass display improved mechanical properties in comparison with the unmodified samples.     

Synthesis and hydrolytic degradation of poly(ethylene succinate) and poly(ethylene terephthalate) copolymers

The conditions of synthesis of statistical poly(ethylene succinate-co-terephthalate) copolymers (2GTS) and high molecular weight poly(ethylene succinate) (PES) with good hydrolytic and optical parameters, designed for the production of biodegradable products and resins, are presented in this article. Copolymers were prepared by melt polycondensation of bis-(β-hydroxyethylene terephthalate) (BHET) and succinic acid (SA) with excess of ethylene glycol (2G) in the presence of a novel titanium/silicate catalyst (C-94) and catalytic grade of germanium dioxide (GeO₂) as cocatalyst. The chemical structure and physical properties of those materials were characterized by ¹H NMR, FT-IR, dynamical-mechanical thermal analyses (DMTA), differential scanning calorimetry (DSC), solution viscosity and spectroscopic methods. The hydrolytic degradation was performed in a water solution with variable pH, also in garden soil and in compost. The highest hydrolytic degradation rate was observed for pH 4 and for compost. Better hydrolytic degradation values in compost medium were observed for copolyester prepared in the presence of GeO₂ as polycondensation cocatalyst. The copolyester with 40 mol% of aliphatic units was chosen for industrial syntheses which were performed in ELANA and subsequently the processing parameters and compatibility with potato starch of this polyester were checked by BIOP Biopolymer Technologies AG.     

pH responsive adhesion of phospholipid vesicle on poly(acrylic acid) cushion grafted to poly(ethylene terephthalate) surface

Polymer-supported lipid bilayer is a key enabling technology for the design and fabrication of novel biomimetic devices. To date, the physical driving force underlying the formation of polymer-supported lipid bilayer remains to be determined. In this study, the interaction between dipalmitoylphosphocholine (DPPC) vesicle and poly(ethylene terephthalate) [PET] surface with or without grafted poly(acrylic acid) [PAA] layer is examined with several biophysical techniques. First, vesicle deformation analysis shows that the geometry of adherent vesicle on either plain PET or PAA-grafted PET surface is best described by a truncated sphere model. At neutral pH, the degree of deformation and adhesion energy are unaltered by the grafted polymerization of acrylic acid on PET surface. Interestingly, the average magnitude of adhesion energy is increased by 185% and −43% on PAA-grated PET and plain PET surface, respectively, towards an increase of pH at room temperature. Our results demonstrate the possibility of tuning the adhesive interaction between vesicle and polymer cushion through the control of polyelectrolyte ionization on the solid support.     

Influence of plasma treatment on the molar mass of poly(ethylene terephthalate) investigated by different chromatographic and spectroscopic methods

The influence of different types of low and atmospheric pressure plasma on poly(ethylene terephthalate) (PET) has been studied in terms of changes in molar mass and molar mass distribution. Apart from a variation of plasma gases (oxygen, helium) different types of plasma (microwave, radio frequency, corona discharge) were used for the plasma surface modification. The changes in molar mass and types of functional end groups of lower molar mass products were investigated by means of matrix-assisted laser desorption/ionization time of flight mass spectrometry (MALDI-TOFMS), whereas the high-molar mass fraction was analyzed by means of size-exclusion chromatography (SEC). The formation of crosslinked products during exposure to a helium plasma, which emits preponderately energy-rich and intense ultraviolet radiation, was proved by means of thermal field-flow fractionation (ThFFF). This method combined with a multiangle laser light scattering (MALLS) detector allows detection of weakly crosslinked polymers and microgels. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1639–1648, 1998     

The effect of annealing on the subsequent cold crystallization of amorphous poly(ethylene terephthalate)

Amorphous poly(ethylene terephthalate) was annealed at temperatures around the glass transition temperature and then heated up in differential scanning calorimeter at 20 °C min⁻¹. It was found that the annealing favored the subsequent cold crystallization and this effect became stronger with increasing annealing temperature. The experimental results were explained by considering the structural change during the annealing.     

Thermal and crystallization characteristics of poly(trimethylene terephthalate)/poly(ethylene naphthalate) blends

Poly(trimethylene terephthalate) (PTT)/poly(ethylene naphthalate) (PEN) blends were miscible in the amorphous state in all of the blend compositions studied, as evidenced by a single, composition-dependent glass transition temperature (T_g) observed for each blend composition. The variation in the T_g value with the blend composition was well predicted by the Gordon-Taylor equation, with the fitting parameter being 0.57. The cold-crystallization peak temperature decreased with increasing PTT content, while the melt-crystallization peak temperature decreased with increasing amount of the minor component. The subsequent melting behavior after both cold- and melt-crystallization exhibited melting point depression, in which the observed melting temperatures decreased with increasing amount of the minor component. During melt-crystallization, both components in the blends crystallized concurrently just to form their own crystals. The blend with 60% w/w of PTT exhibited the lowest total apparent degree of crystallinity.     

The role of crystalline, mobile amorphous and rigid amorphous fractions in the performance of recycled poly (ethylene terephthalate) (PET)

The action of thermo-mechanical degradation induced by mechanical recycling of poly(ethylene terephthalate) was simulated by successive injection moulding cycles. Degradation reactions provoked chain scissions and a reduction in molar mass mainly driven by the reduction of diethyleneglycol to ethylene glycol units in the flexible domain of the PET backbone, and the formation of -OH terminated species with shorter chain length. The consequent microstructural changes were quantified taking into account a three-fraction model involving crystalline, mobile amorphous (MAF) and rigid amorphous fractions (RAF). A remarkable increase of RAF, to a detriment of MAF was observed, while the percentage of crystalline fraction remained nearly constant. A deeper analysis of the melting behaviour, the segmental dynamics around the glass-rubber relaxation, and the macroscopic mechanical performance, showed the role of each fraction leading to a loss of thermal, viscoelastic and mechanical features, particularly remarkable after the first processing cycle.     

Colour formation in poly(ethylene terephthalate) during melt processing

The discolouration, that occurs in virgin poly(ethylene terephthalate) - PET during melt processing, was studied using various bulk and surface analytical techniques. Proton nuclear magnetic resonance (¹H NMR) was used to study the bulk chemical changes occurring in the polymer during thermo-oxidative degradation. Chemical derivatisation with trifluoroacetic anhydride (TFAA) was used to label the hydroxyl groups introduced on the polymer surface by thermal oxidation.From the surface analysis studies using photoacoustic Fourier transform infrared spectroscopy (PA/FT-IR), diffuse reflectance infrared Fourier transform spectroscopy (DRIFT) and X-ray photoelectron spectroscopy (XPS) it was evident that colour formation starts initially with the hydroxylation of the terephthalic ring. Further, the formation of additional carbonyl functionalities and conjugated chromophoric systems complete the colour formation process.     

Study on the pyrolysis of Moroccan oil shale with poly (ethylene terephthalate)

Investigations into the pyrolytic behaviours of oil shale, poly (ethylene terephthalate) (PET) and their mixture have been conducted using a thermogravimetric analyzer. Experiments were carried out dynamically by increasing the temperature from 298 to 1273 K with heating rates of 2 to 100 K/min under a nitrogen atmosphere. Discrepancies between the experimental and calculated TG/DTG profiles were considered as a measurement of the extent of interactions occurring on co-pyrolysis. The maximum degradation temperature of each component in the mixture was higher than those the individual components; thus an increase in thermal stability was expected. The kinetic processing of thermogravimetric data was carried out using Flynn-Wall-Ozawa (FWO) method.     

Alkyd resins derived from glycolized waste poly(ethylene terephthalate)

In this investigation the production of secondary value-added products, such as alkyd resins, derived from the glycolysis of poly(ethylene terephthalate) (PET) is examined as an effective way for its recycling. PET was taken from common soft-drink bottles and diethylene glycol (DEG) was used for the depolymerization at several initial molar ratios. The oligomers obtained were analyzed according to their average molecular weights. Furthermore, the glycolyzed PET products (oligomers) were reacted with maleic anhydride, phthalic anhydride and propylene glycol to form unsaturated polyester resins. These were subsequently mixed with styrene and cured using the benzoyl peroxide/amine initiator system to carry out the reaction in ambient temperature. The curing characteristics of the resins produced were investigated with respect to the initial molar ratio of DEG/PET as well as the initial initiator concentration. Finally, the mechanical properties (tensile strength and elongation at the break point) of the resins were compared with the conventional general purpose resin and were found to be comparable.