Atomic structure of the Si(5 5 12)-2 × 1 surface

Based on the results of scanning tunneling microscopy studies of the reconstructed Si(5 5 12)-2 × 1 surface, its atomic structure has been found. It turns out that Si(5 5 12)-2 × 1 consists of four one-dimensional structures: honeycomb (H) chain, π-bonded H′ (π) chain, dimer-adatom (D/A) row, and tetramer (T) row. Its period is composed of three subunits, i.e., (i) (3 3 7) unit with a D/A row [D(3 3 7)], (ii) (3 3 7) unit with a T row [T(3 3 7)], and (iii) (2 2 5) unit with both a D/A and a T row. Two kinds of adjacent subunits, T(3 3 7)/D(3 3 7) and D(3 3 7)/(2 2 5), are divided by H chains with 2× periodicity due to buckling, while one kind of adjacent subunits, T(3 3 7)/(2 2 5), is divided by a π chain with 1× periodicity. Two chain structures, H and π chains, commute with each other depending upon the external stresses perpendicular to the chain, which is the same for two row structures, D/A and T rows. It can be concluded that the wide and planar reconstruction of Si(5 5 12)-2 × 1 is originates from the stress balance among two commutable chains and two commutable rows.     

Reaction of O2 with the boron-terminated TaB2(0 0 0 1) surface

X-ray photoelectron spectroscopy has been used to study the clean TaB₂(0 0 0 1) surface and its reaction with O₂. In agreement with previous studies, XPS indicates that the clean surface is boron terminated. The topmost boron layer shows a chemically shifted B 1s peak at 187.1 eV compared to a B 1s peak at 188.6 eV for boron layers below the surface. The 187.1-188.6 eV peak intensity ratio and its variation with angle between the crystal normal and the detector is well described by a simple theoretical model based on an independently calculated electron inelastic mean free path of 15.7 Å for TaB₂. The dissociative sticking probability of O₂ on the boron-terminated TaB₂(0 0 0 1) surface is lower by a factor of 10⁴ than for the metal-terminated HfB₂(0 0 0 1) surface.     

Ca induced reconstructions of the Si(0 0 1) surface

The growth behavior of Ca on Si(0 0 1) has been studied with scanning tunneling microscopy and low energy electron diffraction. During the growth of the first atomic layer at elevated temperature, Ca induces several different ordered surface reconstructions. In order of ascending metal content, they are: a 2 × n (n = 3, 4, 5) phase that has limited long range order, a 2 × 6 striped phase, and a 1 × 3 phase. The 1 × 3 phase covers the entire surface at and beyond the point where Ca silicide island growth starts.     

Scaling behavior of island density in submonolayer growth of CaF2 on vicinal Si(1 1 1)

We have studied the scaling behavior of two-dimensional island density during submonolayer growth of CaF₂ on vicinal Si(1 1 1) surfaces using scanning tunneling microscopy. We have analyzed the morphology of the Si(1 1 1) surfaces where CaF₂ partial monolayers with coverages of about 0.1 monolayer are deposited at ∼600 °C. The number density of terrace nucleated islands increases with substrate terrace width l as ∼l⁴ in a low island density regime. This scaling behavior is consistent with predictions for the case of the irreversible growth of islands.     

A surface X-ray diffraction study of TiO2(1 1 0)(3 × 1)-S

Surface X-ray diffraction has been used to investigate the structure of TiO₂(1 1 0)(3 × 1)-S. In concert with existing STM and photoemission data it is shown that on formation of a (3 × 1)-S overlayer, sulphur adsorbs in a position bridging 6-fold titanium atoms, and all bridging oxygens are lost. Sulphur adsorption gives rise to significant restructuring of the substrate, detected as deep as the fourth layer of the selvedge. The replacement of a bridging oxygen atom with sulphur gives rise to a significant motion of 6-fold co-ordinated titanium atoms away from the adsorbate, along with a concomitant rumpling of the second substrate layer.     

Study of c(2 × 2)-MnAu(0 0 1) layers on Mn(0 0 1) by means of scanning tunneling microscopy/spectroscopy

Intermixing, growth, geometric and electronic structures of gold films grown on antiferromagnetic stacking body-centered-tetragonal manganese (0 0 1) films were studied by means of scanning tunneling microscopy/spectroscopy at room temperature in ultra-high vacuum. We found stable ordered c(2 × 2)-MnAu(0 0 1) alloy layers after depositing Au on pure Mn layers. Since at the fourth layer (5 × 23)-like Au reconstruction appears instead of the c(2 × 2) structure and local density of states peaks obtained on the c(2 × 2)-MnAu surface disappear, pure Au layers likely grow from the fourth layer.     

TiO2-rich reconstructions of SrTiO3(0 0 1): a theoretical study of structural patterns

We have recently reported structure solutions for the (2 × 1) and c(4 × 2) reconstructions of SrTiO₃(0 0 1) based on high-resolution electron microscopy, direct methods analysis of diffraction data and density functional theory. Both reconstructions were found to be TiO₂-rich and feature a single overlayer of TiO₂ stoichiometry on top of a bulk-like TiO₂ layer. Qualitatively, the two reconstruction geometries differ in the cation sub-lattice of the overlayer only, where Ti atoms occupy half of the fivefold cation sites. In the present work we use density functional theory to generate a number of variations of this structural motif in search of patterns of stability. We find a reliable predictor for the reconstruction energy in the ability of oxygen atoms to relax vertically out of the overlayer plane to minimize non-bonded oxygen-oxygen repulsions. Out-of-plane relaxation of oxygen atoms in turn is modulated by the number and relative position of coordinating Ti atoms, which yields simple empirical rules as to how cations are distributed in low energy reconstructions.     

Highly resolved scanning tunneling microscopy study of Si(0 0 1) surfaces flattened in aqueous environment

A surface preparation method with fine SiO₂ particles in water is developed to flatten Si(0 0 1) surfaces on the nanometer scale. The flattening performance of Si(0 0 1) surfaces after the surface preparation method is investigated by scanning tunneling microscopy. The observed surface is so flat that 95% of the view area (100 × 100 nm²) is composed of only three atomic layers, namely, one dominant layer occupying 50% of the entire area and two adjacent layers. Furthermore, a magnified image shows the outermost Si atoms regularly distributed along the 〈1 1 0〉 direction on terraces.     

Molecular dynamics simulation of the (0 0 0 1) α-Al2O3 and α-Cr2O3 surfaces

A simple, rigid pair-potential model is applied to investigate the dynamics of the (0 0 0 1) α-Al₂O₃ and α-Cr₂O₃ surfaces using the molecular dynamics technique. The simulations employ a two-stage equilibration process: in the first stage the simulation-cell size is determined via the constant-stress ensemble, and in the second stage the equilibration of the size-corrected simulation cell is continued in the canonical ensemble. The thermal expansion coefficients of bulk alumina and chromia are evaluated as a function of temperature. Furthermore, the surface relaxation and mean-square displacement of the atoms versus depth into the slab are calculated, and their behaviour in the surface region analysed in detail. The calculations show that even moderate temperatures (∼400 °C) give rise to displacements of the atoms at the surface which are similar to the lattice mismatch between α-alumina and chromia. This will help in the initial nucleation stage during thin film growth, and thus facilitate the deposition of α-Al₂O₃ on (0 0 0 1) α-Cr₂O₃ templates.     

Study of Si(0 0 1)4 × 2-Ga structure by scanning tunneling microscopy and ab initio calculation

We have studied Si(0 0 1)-Ga surface structures formed at Ga coverages of slightly above 0.50 monolayer (ML) at 250 °C by scanning tunneling microscopy (STM). 4 × 2-, 5 × 2-, and 6 × 2-Ga structures were observed in a local area on the surface. The 4 × 2-Ga structure consists of three protrusions, as observed in filled- and empty-state STM images. The characters of these structures are clearly different from those of other Si(0 0 1)-Ga structures. We also performed an ab initio calculation of the energetics for several possible models for the 4 × 2-Ga structure, and clarified that the three-orthogonal-Ga-dimer model is the most stable. Also, the results of comparing the simulated STM images and observation images at various bias voltages indicate that this structural model is the most favorable.     

Formation mechanism of the Si(1 1 1)7×7 reconstruction studied by scanning tunneling microscopy: Zipper-like restructuring in the sequential size changes of isolated single faulted-halves

The formation mechanism of the 7×7 reconstruction on annealed Si(1 1 1) surfaces has been demonstrated at the atomic level. In situ observations of unreconstructed regions (‘1×1’) on terraces after rapid quenching to 380 °C were done using scanning tunneling microscopy (STM) with a scanning speed of 1.7 s per frame. In the narrow ‘1×1’ regions, we imaged isolated single-faulted (F) halves of the dimer-adatom-stacking-fault (DAS) structure from “birth” to “death”. During “life”, the isolated single F-halves frequently changed their size. The size changes between odd-sized F-halves always took place through even-sized F-halves of intermediate sizes: 5×5-F^′↔6×6-F↔7×7-F^′↔8×8-F↔9×9-F^′↔10×10-F↔11×11-F^′↔12×12-F↔13×13-F^′, where the 5×5-F^′, 7×7-F^′ and so forth are irregular-type structures of the odd-sized F-halves. Even-sized F-halves and the irregular-type structures are necessary in the size changes, whereas the regular-type structures have never been involved. Lifetimes of the 10×10-F, 8×8-F, and 6×6-F at 380 °C are about 10.5, 6, and 2-3 s, respectively, which are much shorter than those of the isolated irregular-type structures of the odd-sized F-halves. With the aid of room temperature STM images of a rapidly quenched surface, we determined the atomic structures of the even-sized F-halves. We have proposed a sequential size change (SSC) model, including undiscovered parts of the size changes ‘1×1’ ↔2×2-F↔3×3-F^′↔4×4-F↔5×5-F^′, as the formation and decay mechanism of isolated single F-halves in the ‘1×1’ region. The SSC model has the following sequence: ‘1×1’ ↔ 2×2-F↔3×3-F^′↔4×4-F↔5×5-F^′↔6×6-F↔7×7-F^′↔8×8-F↔9×9-F^′↔10×10-F↔11×11-F^′↔12×12-F↔13×13-F^′. It was found by collecting statistics of size-change directions that one of two equivalent sides of the irregular-type structures, which have a mirror symmetry, is involved in the size changes thus indicating that other parts of the F-halves remain unchanged. Based on such findings, we have proposed the atomic processes for bond-rearrangements in the SSC model. The bond-rearrangements proceed along one side of a triangular F-half by breaking the existing dimers and forming new dimers like a “zipper”. Proposed atomic processes of the zipper-like restructuring are illustrated by a ball-and-stick model. The reason for the appearance of the even-sized F-halves and the irregular-type structures of the odd-sized ones is discussed in terms of the energy barrier heights along a reaction path in the size change of single F-halves.     

Decay of multilayer holes on SrTiO3(0 0 1)

We have studied the decay kinetics of nanoscale multilayer holes on SrTiO₃(0 0 1) surfaces, using variable temperature scanning tunneling microscopy. We have performed real time observation of the decay of multilayer holes with diameters of 10 nm order at 750 °C. We have found that the hole decays, filling layer by layer from the bottom while expanding the periphery of the hole. We have performed numerical simulations of hole decay based on a step flow model. The observed decay kinetics is found to be diffusion limited with local mass conservation.     

Aromatic interactions in the close packing of phenyl-imides at Cu(1 1 0) surfaces

The oxidation of aniline at Cu(1 1 0) surfaces at 290 K has been studied by XPS and STM. A single chemisorbed product, assigned to a phenyl imide (C₆H₅N(a)), is formed together with water which desorbs. Reaction with preadsorbed oxygen results in a maximum surface concentration of phenyl imide of 2.8 × 10¹⁴ mol cm⁻² and a surface dominated by domains of three structures described by , and unit meshes. However, concentrations of phenyl imide of up to 3.3 × 10¹⁴ mol cm⁻² were obtained from the coadsorption of aniline and dioxygen (300:1 mixture) resulting in a highly ordered biphasic structure with and domains. Comparison of the STM and XPS data shows that only half the phenyl imides at the surface are imaged. Pi-stacking of the phenyl rings is proposed to account for this observation.     

Mixed PbSi dimer chains on Si(1 0 0): a first-principles study

It has been a common belief that the one-dimensional structures observed by STM at low coverage of Pb on Si(1 0 0) are buckled Pb-Pb dimer chains. However, using first-principles density functional calculations, we found that it is energetically favorable for Pb adatoms to intermix with Si atoms to form mixed dimer chains on Si(1 0 0), instead of Pb-Pb dimer chains as assumed in previous studies. Up to a Pb coverage of 0.125 ML, mixed PbSi dimer chain is 0.19 eV per Pb atom lower in energy than Pb dimer chain.     

Reflection high-energy positron diffraction pattern from a Si(1 1 1)-(7 × 7) surface

We have investigated the feature of reflection high-energy positron diffraction (RHEPD) pattern from a Si(1 1 1)-(7 × 7) surface. The RHEPD pattern observed in the total reflection condition is quite different from the conventional reflection high-energy electron diffraction (RHEED) pattern. This fact is attributed to the different penetration depths of positrons and electrons. We show that the intensity distribution of RHEPD pattern is reproduced considering the dimer-adatom-stacking fault (DAS) model with optimized atomic positions and scattering potentials of adatoms and rest atoms.     

Structural and statistical analysis of Yb/Si(1 1 1) and Eu/Si(1 1 1) reconstructions

We have performed the structural and statistical analysis of Yb/Si(1 1 1) and Eu/Si(1 1 1) surfaces in the submonolayer regime utilizing low-energy electron diffraction and scanning tunneling microscopy (STM). The almost identical series of one-dimensional chain structures (e.g., 3 × 2/3 × 1, 5 × 1, 7 × 1, 9 × 1, and 2 × 1 phases) are found in order of increasing metal coverage for both adsorbed systems, however, only the Eu/Si system reveals the ‘√3’-like reconstruction before the 2 × 1 endpoint phase. The atomic models of chain structures are proposed and discussed. In particular, our results suggest the odd-order n×1 (n=5,7,9,…) intermediate reconstructions to incorporate the Seiwatz chains and honeycomb chains with the proportion of m:1, where . The statistical analysis of STM images is carried out to examine the correlation of atomic rows on Eu/Si and Yb/Si surfaces. It is found that Eu stabilizes more ordered row configuration compared to Yb, which can be explained in terms of indirect electronic interaction of atomic chains or/and different magnetic properties of adsorbed species.     

Scanning tunnelling microscopy studies of growth morphology in highly epitaxial c-axis oriented Pt thin film on (0 0 1) SrTiO3

A noble metal Pt thin film was successfully grown on (0 0 1) SrTiO₃ substrate by using a DC-sputtering technique. The surface morphology and growth features of the as-grown Pt films were investigated by scanning tunnelling microscopy. Growth conditions, such as pre-sputtering, deposition ambience, and oxygen ratio are found to greatly affect the orientation, the crystallinity, and the epitaxial behavior of Pt films on (0 0 1) SrTiO₃. Single-crystalline Pt films have been achieved by introducing a few percentage oxygen into the sputtering ambient. The in-plane-relationship of the c-axis oriented Pt thin films on (0 0 1) SrTiO₃ was determined to be (0 0 1)_Pt∥(0 0 1)_SrTiO3 and [0 0 1]_Pt∥[0 0 1]_SrTiO3. Oxygen in the sputtering ambient was found to be a key factor to achieve the epitaxial Pt films.     

Self-regulated Ni cluster formation on the TiO2(1 1 0) terrace studied using scanning tunneling microscopy

We have studied the growth mode and morphology of Ni clusters on a TiO₂(1 1 0) surface with a wide terrace using scanning tunneling microscopy (STM) at a low coverage (less than 3 atoms nm⁻²). The Ni clusters are formed on the terrace at the low coverage of 0.2 atoms nm⁻². Their average dimensions are constant in three directions up to 1 atoms nm⁻². The Ni clusters have an oval shape with average sizes of 1.8 nm (along [0 0 1]) × 1.4 nm (along (in the [1 1 0] directions). Above the coverage of 1.0 atoms nm⁻², an increase in the cluster height occurs, retaining an almost constant lateral size. It is proposed that the interaction of the Ni cluster and the support surface regulates the Ni cluster size.