Recoilless fraction, structural, magnetic and thermal properties of Fe73.5Cu1Nb3Si13.5B9 alloy

Differential scanning calorimetry, X-ray diffraction and room temperature Mössbauer spectrum measurements of Fe_73.5Cu₁Nb₃Si_13.5B₉ (Finemet) alloy have been carried out in order to study its structural and magnetic properties as a function of annealing temperature. The DSC profile of as-quenched Finemet showed two exothermic peaks at 530 and 702 °C, corresponding to two crystallization processes. The Finemet alloy remains amorphous at 450 °C with one broad peak in XRD pattern and one broad sextet in Mössbauer spectrum. When the Finemet alloy was annealed at 550 °C, only well indexed body-center-cubic phase was detected. After being annealed at 650 and 750 °C, the XRD patterns showed the coexistence of α-Fe(Si) and Fe-B intermetallic phases with the increase in XRD peak intensities, indicating the growth of crystallites and the decomposition of Fe_73.5Cu₁Nb₃Si_13.5B₉ alloy at elevated temperatures. The Mössbauer spectra of annealed Finemet alloy could be fitted with 4 or 5 sextets and one doublet at higher annealing temperatures, revealing the appearance of different crystalline phases corresponding to the different Fe sites above the crystallization temperature. The appearance of the nanocrystalline phases at different annealing temperatures was further confirmed by the recoilless fraction measurements.     

Thermo-stimulated surface segregation in the ordering alloy Pt80Co20(1 1 1): Experiment and modeling

In this paper, a method of Ionization Spectroscopy (IS) is proposed for the non-destructive layer-by-layer analysis of the elemental composition of a solid surface. Using ionization energy loss spectra, a layer-by-layer concentration profile of the Pt₈₀Co₂₀(1 1 1) alloy surface is obtained for different annealing temperatures. For the disordered Pt₈₀Co₂₀(1 1 1) at room temperature, the first atomic layer consists of pure Pt with damped oscillations in the deeper layers. Heating the sample reduces the oscillations. However, at a temperature of 823 K, a sandwich-like structure of the type Pt/Co/Pt was found in the first three atomic layers. For the ordered state the first atomic layer also consists of pure Pt with bulk concentration in other layers. LEED analysis shows a p(2 × 2) superstructure for the surface of the ordered Pt₈₀Co₂₀(1 1 1) alloy. The segregation behavior in this alloy is further studied by Monte Carlo (MC) simulations combined with the Constant Bond Energy (CBE) model. The results of the MC simulations agree well with the experiments at the higher temperatures, both for the surface composition and the concentration depth profile. At lower temperatures, some discrepancies exist between the MC results and the measured concentration profile.     

Surface oxidation of NiCo alloy: A comparative X-ray photoelectron spectroscopy study in a wide pressure range

Oxidation of NiCo alloy has been studied under two pressure regimes, 5 × 10⁻¹⁰ and 5 × 10⁻¹ bar, by X-ray photoelectron spectroscopy (XPS). The aim of this work is to investigate the synergetic effect between the two alloy components during the initial stages of oxidation. The results showed that at low oxygen pressure, segregation and preferential oxidation of cobalt takes place, while oxidation of nickel is largely suppressed. The species dominating the surface is CoO but small amount of metallic cobalt still remains even after prolonged oxidation at 670 K. At 0.5 bar O₂ pressure, alloy oxidation was found to be temperature depended. From 420 K to 520 K, cobalt is completely transformed to CoO and the Ni:Co atomic ratio at the surface approaches a minimum, similar to the observations at low pressure regime. However, at higher temperatures (from 520 K to 720 K), nickel is re-segregated on the surface, in the expense of cobalt, while CoO is further oxidized to Co₃O₄. At this temperature range formation of mixed Ni-Co-O spinel-like oxides is probable as supported by the characteristic modifications of the Ni 2p_3/2 photoelectron peak and the increase of the Ni:Co atomic ratio.     

FINEMET type alloy without Si: Structural and magnetic properties

Magnetic and structural properties of a Finemet type alloy (Fe_73.5Ge_15.5Nb₃B₇Cu₁) without Si and high Ge content were studied. Amorphous material was obtained by the melt spinning technique and was heat treated at different temperatures for 1 h under high vacuum to induce the nanocrystallization of the sample. The softest magnetic properties were obtained between 673 and 873 K. The role of Ge on the ferromagnetic paramagnetic transition of the as-quenched alloys and its influence on the crystallization process were studied using a calorimetric technique. Mössbauer spectroscopy was employed in the nanocrystallized alloy annealed at 823 K to obtain the composition of the nanocrystals and the amorphous phase fraction. Using this data and magnetic measurements of the as-quenched alloy, the magnetic contribution of nanocrystals to the alloy annealed at 823 K was estimated via a linear model.     

Formation, stability and CO adsorption properties of PdAg/Pd(1 1 1) surface alloys

The formation, stability and CO adsorption properties of PdAg/Pd(1 1 1) surface alloys were investigated by X-ray photoelectron spectroscopy (XPS) and by adsorption of CO probe molecules, which was characterized by temperature-programmed desorption (TPD) and high resolution electron energy loss spectroscopy (HREELS). The PdAg/Pd(1 1 1) surface alloys were prepared by annealing (partly) Ag film covered Pd(1 1 1) surfaces, where the Ag films were deposited at room temperature. Surface alloy formation leads to a modification of the electronic properties, evidenced by core-level shifts (CLSs) of both the Pd(3d) and Ag(3d) signal, with the extent of the CLSs depending on both initial Ag coverage and annealing temperature. The role of Ag pre-coverage and annealing temperature on surface alloy formation is elucidated. For a monolayer Ag covered Pd(1 1 1) surface, surface alloy formation starts at ∼450 K, and the resulting surface alloy is stable upon annealing at temperatures between 600 and 800 K. CO TPD and HREELS measurements demonstrate that at 120 K CO is exclusively adsorbed on Pd surface atoms/Pd sites of the bimetallic surfaces, and that the CO adsorption behavior is dominated by geometric ensemble effects, with adsorption on threefold hollow Pd₃ sites being more stable than on Pd₂ bridge sites and finally Pd₁ a-top sites.     

CoPt alloy grown on the WSe2(0 0 0 1) van der Waals surface

The structural and magnetic properties of 3-nm-thick CoPt alloys grown on WSe₂(0 0 0 1) at various temperature are investigated. Deposition at room temperature leads to the formation of a chemically disordered fcc CoPt alloy with [1 1 1] orientation. Growth at elevated temperatures induces L1₀ chemical order starting at 470 K accompanied with an increase in grain size and a change in grain morphology. As a consequence of the [1 1 1] growth direction, the CoPt grains can adopt one of the three possible variants of the L1₀ phase with tetragonal c-axis tilted from the normal to the film plane direction at 54°. The average long-range order parameter is found to be 0.35(±0.05) and does not change with the increase in the deposition temperature from 570 to 730 K. This behavior might be related to Se segregation towards the growing facets and surface disorder effects promoted by a high surface-to-volume ratio. Magnetic studies reveal a superparamagnetic behavior for the films grown at 570 and 730 K in agreement with the film morphology and degree of chemical order. The measurements at 10 K reveal the orientation of the easy axis of the magnetization lying basically in the film plane.     

Magnetization behavior and magnetocaloric effect in bulk amorphous Fe60Co5Zr8Mo5W2B20 alloy

Microstructure by X-ray diffraction and Mössbauer spectroscopy, and isothermal magnetic entropy changes in the bulk amorphous Fe₆₀Co₅Zr₈Mo₅W₂B₂₀ alloy in the as-quenched state and after annealing at 720 K for 15 min are studied. The as-cast and heat treated alloy is paramagnetic at room temperature. The quadrupole splitting distribution is unimodal after annealing indicating the more homogenous structure in comparison with that for the as-cast alloy. Curie temperature slightly increases after annealing from 265±2 K in the as-quenched state to 272±2 K and the alloy exhibits the second order magnetic phase transition. The maximum of isothermal magnetic entropy changes appears at the Curie points and is equal to 0.30 and 0.42 J/(kg·K) for the alloy in the as-quenched state and after annealing, respectively. In the paramagnetic region the material behaves as a Curie-Weiss paramagnet.     

Phase analysis and magnetocaloric properties of Zr substituted Gd-Si-Ge alloys

The structure, microstructure, magneto-structural transition and magnetocaloric effect have been investigated in series of (Gd_5−xZr_x)Si₂Ge₂ alloys with 0≤x≥0.20. X-ray powder diffraction analysis revealed the presence of orthorhombic structure for Zr containing alloys at room temperature in contrast to the monoclinic structure observed in the parent Gd₅Si₂Ge₂ alloy. The microstructural studies reveal that, low Zr addition (x≤0.1) resulted in low volume fraction of detrimental Gd₅Si₃-type secondary phase compared to that present in the parent alloy. All the Zr containing alloys have shown the presence of only second order magnetic transition unlike the parent alloy showing both first order structural and second order magnetic transition. A moderate (ΔS)_M value of −5.5 J/kg K was obtained for the x=0.05 alloy at an enhanced operating temperature of 292 K compared to −7.8 J/kg K at 274 K of the parent alloy for an applied field of 2 T. The interesting feature of Zr (x=0.05) containing alloy is the wide operating temperature range of ∼25 K than that of ∼10-12 K for the parent, which resulted in enhanced net refrigerant capacity of 103 J/kg compared to that of 53 J/kg for the parent alloy.     

In situ scanning tunneling microscopy studies of bimetallic cluster growth: Pt-Rh on TiO2(1 1 0)

The growth of Pt on clusters on TiO₂(1 1 0) in the presence and absence of Rh was investigated by scanning tunneling microscopy (STM) for Pt deposited on top of 0.3 ML Rh clusters (Rh + Pt). In situ STM studies of Pt growth at room temperature show that bimetallic clusters are produced when Pt is directly incorporated into existing Rh clusters or when newly nucleated clusters of pure Pt coalesce with existing Rh clusters. Low energy ion scattering experiments demonstrate that Rh is still present at the surface of the clusters even after deposition of 2 ML of Pt, indicating that Rh atoms can diffuse to the cluster surface at room temperature. Rh clusters were found to seed the growth of Pt clusters at room temperature as well as 100 K and 450 K. Furthermore, clusters as large as 100 atoms were observed to be mobile on the surface at room temperature and 450 K, but not at 100 K. Pt deposition at 100 K exhibited more two-dimensional cluster growth and higher cluster densities compared to room temperature experiments due to the lower diffusion rate. Increased diffusion rates at 450 K resulted in more three-dimensional cluster growth and lower densities for pure Pt growth, but cluster densities for Pt + Rh growth were the same as at room temperature.     

Optical and electrical properties of thermally oxidized bismuth thin films

Bismuth trioxide (Bi₂O₃) thin films were prepared by dry thermal oxidation of metallic bismuth films deposited by vacuum evaporation. The oxidation process of Bi films consists of a heating from the room temperature to an oxidation temperature (T_o = 673 K), with a temperature rate of 8 K/min; an annealing for 1 h at oxidation temperature and, finally, a cooling to room temperature. The optical transmission and reflection spectra of the films were studied in spectral domains ranged between 300 nm and 1700 nm, for the transmission coefficient, and between 380 nm and 1050 nm for the reflection coefficient, respectively. The thin-film surface structures of the metal/oxide/metal type were used for the study of the static current-voltage (I-U) characteristics. The temperature of the substrate during bismuth deposition strongly influences both the optical and the electrical properties of the oxidized films. For lower values of intensity of electric field (ξ < 5 × 10⁴V/cm), I-U characteristics are ohmic.     

Ethylene dissociation on flat and stepped Ni(1 1 1): A combined STM and DFT study

The dissociative adsorption of ethylene (C₂H₄) on Ni(1 1 1) was studied by scanning tunneling microscopy (STM) and density functional theory (DFT) calculations. The STM studies reveal that ethylene decomposes exclusively at the step edges at room temperature. However, the step edge sites are poisoned by the reaction products and thus only a small brim of decomposed ethylene is formed. At 500 K decomposition on the (1 1 1) facets leads to a continuous growth of carbidic islands, which nucleate along the step edges.DFT calculations were performed for several intermediate steps in the decomposition of ethylene on both Ni(1 1 1) and the stepped Ni(2 1 1) surface. In general the Ni(2 1 1) surface is found to have a higher reactivity than the Ni(1 1 1) surface. Furthermore, the calculations show that the influence of step edge atoms is very different for the different reaction pathways. In particular the barrier for dissociation is lowered significantly more than the barrier for dehydrogenation, and this is of great importance for the bond-breaking selectivity of Ni surfaces.The influence of step edges was also probed by evaporating Ag onto the Ni(1 1 1) surface. STM shows that the room temperature evaporation leads to a step flow growth of Ag islands, and a subsequent annealing at 800 K causes the Ag atoms to completely wet the step edges of Ni(1 1 1). The blocking of the step edges is shown to prevent all decomposition of ethylene at room temperature, whereas the terrace site decomposition at 500 K is confirmed to be unaffected by the Ag atoms.Finally a high surface area NiAg alloy catalyst supported on MgAl₂O₄ was synthesized and tested in flow reactor measurements. The NiAg catalyst has a much lower activity for ethane hydrogenolysis than a similar Ni catalyst, which can be rationalized by the STM and DFT results.     

First-principles investigations of the Ni3Sn alloy at steam reforming conditions

The structure and surface composition of a Ni₃Sn alloy at conditions relevant for the steam reforming reaction was investigated using density functional theory calculations. Both the flat Ni₃Sn(0 0 0 1) surface and a surface with steps in the closed packed direction [1 0  0]were considered. The adsorption geometries and energies of the species CO, C, OH and H were calculated. Chemical potentials were used to map out which adsorbates are on the surface under varying conditions. It was found that adsorbates preferably bind to Ni as nearest neighbor with Sn as second-nearest neighbor. The binding energy is slightly stronger than on pure Ni. Adsorbate binding to Sn was found to be very unfavorable. Binding free energies indicate that at high temperature the alloy surface will be predominantly covered by CO and C, and at low temperatures one may find H and almost no OH. Even though the nominal composition of the investigated alloy is Ni₃Sn, the surface composition may differ significantly depending on temperature and pressure of the gas phase. This effect was investigated by calculating segregation energies both in the absence and in the presence of adsorbates. For the flat surface, it was found that only the bulk termination is present under relevant conditions. In contrast, it was found that for steps preferential adsorption of CO and C on Ni sites may lead to adsorption-induced segregation at temperatures below 400 °C. When taking segregation into account, the most stable Ni₃Sn surfaces will not bind CO or C at the same condition that Ni does. This is in excellent agreement with the previously proven ability of Ni-Sn alloys to inhibit graphite formation.     

Adsorption of glycine on a NiAl(1 1 0) alloy surface

The adsorption and desorption of glycine (NH₂CH₂COOH), vacuum deposited on a NiAl(1 1 0) surface, were investigated by means of Auger electron spectroscopy (AES), low energy electron diffraction (LEED), temperature-programmed desorption, work function (Δφ) measurements, and ultraviolet photoelectron spectroscopy (UPS). At 120 K, glycine adsorbs molecularly forming mono- and multilayers predominantly in the zwitterionic state, as evidenced by the UPS results. In contrast, the adsorption at room temperature (310 K) is mainly dissociative in the early stages of exposure, while molecular adsorption occurs only near saturation coverage. There is evidence that this molecularly adsorbed species is in the anionic form (NH₂CH₂COO⁻). Analysis of AES data reveals that upon adsorption glycine attacks the aluminium sites on the surface. On heating part of the monolayer adsorbed at 120 K is converted to the anionic form and at higher temperatures dissociates further before desorption. The temperature-induced dissociation of glycine (<400 K) leads to a series of similar reaction products irrespective of the initial adsorption step at 120 K or at 310 K, leaving finally oxygen, carbon and nitrogen at the surface. AES and LEED measurements indicate that oxygen interacts strongly with the Al component of the surface forming an “oxide”-like Al-O layer.     

High sensitivity absorption spectroscopy of methane at 80 K in the 1.58 μm transparency window: Temperature dependence and importance of the CH3D contribution

The high resolution absorption spectrum of methane in the 1.58 μm transparency window has been recorded at room temperature and at 79 K by CW-Cavity Ring Down Spectroscopy using a cryogenic cell and a series of Distributed Feed Back (DFB) diode lasers. The achieved sensitivity (α_min ∼ 3 × 10⁻¹⁰ cm⁻¹) has allowed for a detailed characterization of the 6289-6526 cm⁻¹ region which corresponds to the lowest opacity of the transparency window. A list of 6868 and 4555 transitions with intensities as weak as 1 × 10⁻²⁹ cm/molecule was constructed from the recordings at 297 and 79 K, respectively. By comparison with a spectrum of CH₃D recorded separately by Fourier Transform Spectroscopy, 1282 and 640 transitions of monodeuterated methane, CH₃D, in natural abundance in our sample were identified at 297 and 79 K, respectively.The rotational temperature determined from the intensity distribution of the 3ν₂ band of CH₃D (79.3 K) was found in good agreement with the temperature value previously obtained from the Doppler line broadening. The reduction of the rotational congestion by cooling down to 79 K reveals a spectral region near 6300 cm⁻¹ where CH₃D transitions are dominant.The low energy values of the transitions observed both at 79 K and at room temperature were derived from the variation of their line intensities. These transitions with lower energy determination represent 93.9% and 68.4% of the total absorbance in the region, at 79 K and room temperature, respectively. The quality of the obtained empirical low energy values is demonstrated for CH₄ by the marked propensity of the empirical low J values to be close to integers. The line lists at 79 K and room temperature provided as Supplementary Material allow accounting for the temperature dependence of methane absorption between these two temperatures. The investigated region covering the 5ν₄ band of the ¹²CH₄ isotopologue will be valuable for the theoretical treatment of this band which is the lowest energy band of the icosad.     

Magnetic, magnetocaloric, and magnetotransport properties of RCo1.8Mn0.2 (R=Er, Ho, Dy, and Tb) compounds

The magnetic, magnetocaloric, and magnetotransport properties of RCo_1.8Mn_0.2 (R=Er, Ho, Dy, and Tb) were studied by room temperature X-ray diffraction, magnetization, and resistivity measurements at a temperature interval of 5-400 K and magnetic fields up to 5 T. The Curie temperature of RCo₂ was found to increase significantly when 10% Mn was substituted for Co. The effective paramagnetic moments were found to be in reasonable agreement with their theoretical values. A large magnetoresistance (MR) of Δρ/ρ_o≈−13.5% for R=Ho at T≈153 K for ΔH=5 T has been observed. The maximum relative cooling capacities vary from 467 J/kg at low temperature for R=Er to 202 J/kg at the near room temperature for R=Tb.     

Comparative study of optical parameters of fullerene C60 film at different temperatures

Fullerene C₆₀ thin films on glass substrate (around 2000 ? thickness) were prepared by thermal evaporation technique. The structural, surface morphology and optical properties of the films were studied. The optical properties of fullerene C₆₀ were investigated in the spectral range 200 nm to 900 nm using a UV-Vis spectrophotometer at room temperature as well as at liquid nitrogen temperature (77 K). The optical band gap at room temperature is found to be 2.30 eV, which gradually decreases with lowering the temperature and reaches to 2.27 at 77 K. The thickness and refractive index of fullerene C₆₀ film were calculated by ellipsometry. From the X-ray analysis, we have calculated the grain size, dislocation density, number of crystallite per unit area, and strain of the film at room temperature. The surface morphology of film was analyzed by scanning electron microscope (SEM). The present result show that the fullerene C₆₀ film becomes more conducting at low temperature.     

The chemical potential in surface segregation calculations: AgPd alloys

We put forward a technique for calculating the surface segregation profile in substitutional disordered alloys. The surface internal energy and the effective bulk and surface chemical potentials are calculated using the full charge density exact muffin-tin orbitals method, combined with the coherent potential approximation. The application of our approach is demonstrated to the close-packed surface of Ag_cPd_1−c random alloys with 0 < c < 1. The surface concentration profile, surface energy and segregation energy are investigated as functions of bulk composition. The present results are compared with former theoretical and experimental data. It is found that at low temperature, Ag segregates to the surface layer for the entire bulk composition range. At 0 K, the subsurface layer contains 100% Pd for c ? 0.4, and somewhat more than (2c − 1) Ag in alloys with c > 0.5. The temperature dependence of the segregation profile is significant for Pd rich alloys and for alloys with intermediate concentrations. At temperatures ?600 K, the subsurface layer is obtained to be almost bulk like.     

Stable atomic structure and magnetism of Pt–Cr binary surface alloys on Pt(0 0 1): First-principle calculations

The possibility of Pt–Cr surface alloys formation on Pt(0 0 1) was investigated and their magnetism was calculated by the full-potential linearized augmented plane wave (FLAPW) method with eight different atomic configurations. The most stable structure was calculated to be the Pt-segregated L1₂ ferromagnetic surface alloy. A₃B types (L1₂ or D0₂₂) were more stable compared to AB types (L1₀). It implies that the A₃B type surface alloys may be formed when depositing a monolayer of Cr on Pt(0 0 1). It was found from the total energy calculations that there exists a strong tendency of the Pt segregation. The segregation further stabilizes the surface alloy significantly. The work function of the most stable surface alloy was calculated to be 6.02 eV and the magnetic moment of the surface Cr was much enhanced to 3.3 μ_B. It is a quite interesting finding that the coupling between Cr and Pt atoms on the surface plane is ferromagnetic in the Pt-segregated L1₂ ferromagnetic surface alloy, while the coupling is antiferromagnetic in the bulk.     

Morphology and composition of nanoscale surface oxides on Fe–20Cr–18Ni{1 1 1} austenitic stainless steel

Surface oxidation ranging from initial stages to the onset of passive oxide layer formation have been investigated on Fe–20Cr–18Ni{1 1 1} single crystal surface by X-ray photoelectron spectroscopy (XPS). Surface segregation of the alloying elements and the morphology of the surface oxide nanostructure were characterized quantitatively by inelastic electron background analysis. Our results demonstrate that by increasing the oxidation temperature the relative concentrations of Fe²⁺ and Fe³⁺ cations increase due to their enhanced mobility. Higher temperature also improves the mobility of chromium, thus enhancing its segregation to the oxygen-rich surface and thereby reinforcing the passive layer on the alloy. This is in agreement with the results showing the sudden decrease in oxide film thickness at the oxidation temperatures exceeding 600 K. Additionally, a pronounced segregation of metallic nickel is found in the interface between the surface oxide layer and the bulk alloy.     

Surface phase transition and electronic structure of c(5√2 × √2)R45°-Pb/Cu(1 0 0)

The c(5√2 × √2)R45°-Pb/Cu(1 0 0) surface phase is investigated by means of angle resolved ultraviolet photoemission and low energy electron diffraction in the temperature range between 300 and 550 K. We identify and characterize a temperature-induced surface phase transition at 440 K from the room temperature c(5√2 × √2) R45° phase to a (√2 × √2)R45° structure with split superstructure spots. The phase transition is fully reversible and takes place before the two-dimensional melting of the structure at 520 K. The electronic structure of the split (√2 × √2)R45° phase is characterized by a metallic free-electron like surface band. This surface band is backfolded with c(5√2 × √2)R45° periodicity phase at room temperature, giving rise to a surface band gap at the Fermi energy. We propose that a gain in electronic energy explains in part the stability of the c(5√2 × √2)R45° phase.