Nanostructure and optical properties of M doped ZnO (M=Ni, Mn) thin films prepared by sol-gel process

The transparent thin films of undoped, Mn-doped, and Ni-doped zinc oxide (ZnO) have been deposited on glass substrates via sol-gel technique using zinc acetate dehydrate, nickel chloride, and manganese chloride as precursors. The structural properties and morphologies of the deposited undoped and doped ZnO thin films have been investigated. X-ray diffraction (XRD) spectra, scanning electron microscopy (SEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) were used to examine the morphology and microstructure of the thin films. Optical properties of the thin films were determined by photoluminescence (PL) and UV/vis spectroscopy. The analyzed results indicate that the obtained films are of good crystal quality and have smooth surfaces, which have a pure hexagonal wurtzite ZnO structure without any Mn or Ni related phases. The band gap energy was estimated by Tauc's method and found to be 3.28, 3.26, and 3.34 eV for ZnO, Ni-doped ZnO, and Mn-doped ZnO thin films at room temperature, respectively. Room temperature photoluminescence is observed for the ZnO, Ni-doped ZnO, and Mn-doped ZnO thin films.     

DLC nano-dot surfaces for tribological applications in MEMS devices

With the invention of miniaturized devices like micro-electro-mechanical systems (MEMS), tribological studies at micro/nano-scale have gained importance. These studies are directed towards understanding the interactions between surfaces at micro/nano-scales, under relative motion. In MEMS devices, the critical forces, namely adhesion and friction restrict the smooth operation of the elements that are in relative motion. These miniaturized devices are traditionally made from silicon (Si), whose tribological properties are not good. In this paper, we present a short investigation of nano- and micro-tribological properties of diamond-like carbon (DLC) nano-dot surfaces. The investigation was undertaken to evaluate the potential of these surfaces for their possible application to the miniaturized devices. The tribological evaluation of the DLC nano-dot surfaces was done in comparison with bare Si (1 0 0) surfaces and DLC coated silicon surfaces. A commercial atomic force microscope (AFM) was used to measure adhesion and friction properties of the test materials at the nano-scale, whereas a custom-built micro-tribotester was used to measure their micro-friction property. Results showed that the DLC nano-dot surfaces exhibited superior tribological properties with the lowest values of adhesion force, and friction force both at the nano- and micro-scales, when compared to the bare Si (1 0 0) surfaces and DLC coated silicon surfaces. In addition, the DLC nano-dot surfaces showed no observable wear at the micro-scale, unlike the other two test materials. The superior tribological performance of the DLC nano-dot surfaces is attributed to their hydrophobic nature and the reduced area of contact projected by them.     

Surface properties of ionomers based on styrene-b-acrylic acid copolymers obtained by copolymerization in emulsion

Surface properties of styrene-b-acrylic acid copolymers obtained in emulsion and suitable ionomers before and after UV-irradiation were studied by measurements of contact angles and FTIR-ATR spectroscopy.The research focused on the influence of different content of carboxylic acid groups in copolymers, of various types and contents of alkali metal salts in ionomers and of cesium acrylate or methacrylate in ionomers on hydrophilicity of the surfaces of these samples and the course of photodegradation in them.Hydrophilicity of initial copolymer surfaces was higher than this of polystyrene as a result of presence of carboxylic acid groups, which also made the surfaces of these copolymers more sensitive to UV-irradiation.Hydrophilicity of the surfaces of ionomers containing cesium acrylates depended on the content of cesium salt in the samples. The course of ionomer photooxidation was also dependent on the content of this salt.The surface of ionomer containing cesium methacrylate was more polar than this of ionomer containing cesium acrylate.Styrene-based ionomers containing 3.7 mol% of various alkali metal acrylates had less polar surfaces than initial copolymer and they were also more resistant to UV-irradiation in comparison to the initial copolymer.Copolymers obtained in emulsion and suitable ionomers had more polar surfaces and they were more sensitive to UV-light compared to copolymers obtained in bulk and their ionomers.     

Film forming kinetics and reaction mechanism of γ-glycidoxypropyltrimethoxysilane on low carbon steel surfaces

The film forming kinetics and reaction mechanism of γ-GPS on low carbon steel surfaces was investigated by FTIR-ATR, AFM, NSS and theoretical calculation method. The results from experimental section indicated that the reaction of γ-GPS on low carbon steel surfaces followed the conventional reaction mechanism, which can be described as reaction (I) (Me (Metal)-OH + HO-Si → Me-O-Si + H₂O) and reaction (II) (Si-OH + Si-OH → Si-O-Si + H₂O). During film forming process, the formation of Si-O-Fe bond (reaction (I)) exhibited oscillatory phenomenon, the condensation degree of silanol monomers (reaction (II)) increased continuously. The metal hydroxyl density had significant influence on the growth mechanisms and corrosion resisting property of γ-GPS films. The results from theoretical calculation section indicated that the patterns of reaction (I) and reaction (II) were similar, involving a nucleophilic attack on the silicon center. The formation of Si-O-Fe bond (reaction (I)) was kinetically and thermodynamically preferred, which had catalytic effect on its condensation with neighboring silanol monomers (reaction (II)). Our DFT calculations were good consistent with the experimental measurements.     

Thermal stability of alkoxy monolayers grafted on Si(1 1 1)

Direct grafting of organic monolayers on Si is of prime interest in order to give specific properties to a silicon surface. However, for microelectronics applications, this possibility is hampered by the limited stability of the grafted layers. It has been previously established that alkyl layers attached to Si surfaces through Si-C bonds become unstable at 250-300 °C, by desorption of alkenes. Changing the nature of the bonding to the surface might allow one to circumvent this desorption pathway and increase the layer stability. In our work, decanol and decyl aldehyde are reacted with the Si(1 1 1)-H surface at ∼100 °C during 20 h in order to obtain alkoxy monolayers. FTIR measurements performed in ATR geometry show that the grafted molecule surface coverage is on the order of 33% after reaction with decanol and 50% after reaction with decyl aldehyde. Characterization by AFM essentially reveals that the morphology of the grafted surfaces is unaffected as compared to that of Si-H surfaces. However, the edges of the terraces at alcohol-grafted surfaces exhibit some pitting, probably due to the presence of water in the grafting liquid. Thermal stability studies show that alkoxy chains progressively disappear from the Si surface between 200 and 400 °C. From the CH₂/CH₃ ratio in the CH region (2760-3070 cm⁻¹), it appears that the chains undergo progressive dissociation by C-C bond breaking before their complete disappearance from the surface. Therefore, the thermal behaviour of alkoxy monolayers appears quite distinct from that of alkyl monolayers that tend to leave the surface in a much narrower temperature range (250-350 °C), essentially via breaking of the Si-C bonds.     

Zinc oxide catalyzed growth of single-walled carbon nanotubes

We demonstrate that zinc oxide can catalyze the growth of single-walled carbon nanotubes (SWNTs) with high efficiency by a chemical vapor deposition process. The zinc oxide nanocatalysts, prepared using a diblock copolymer templating method and characterized by atomic force microscopy (AFM), were uniformly spaced over a large deposition area with an average diameter of 1.7 nm and narrow size distribution. Dense and uniform SWNTs films with high quality were obtained by using a zinc oxide catalyst, as characterized by scanning electron microscopy (SEM), Raman spectroscopy, AFM, and high-resolution transmission electron microscopy (HRTEM).     

An atomic force microscopy study of DNA hairpin probes monolabelled with gold nanoparticle: Grafting and hybridization on oxide thin films

First and original results are reported regarding the surface evolution of two kinds of oxide film after covalent grafting and hybridization of hairpin oligonucleotide probes. These hairpin probes were monolabelled with a 1.4 nm gold nanoparticle. One kind of oxide film was rough Sb doped SnO₂ oxide film and the other kind was smooth SiO₂ film. Same process of covalent grafting, involving a silanization step, was performed on both oxide surfaces. Atomic force microscopy (AFM) was used to study the evolution of each oxide surface after different steps of the process: functionalization, probe grafting and hybridization. In the case of rough SnO₂ films, a slight decrease of the roughness was observed after each step whereas in the case of smooth SiO₂ films, a maximum of roughness was obtained after probe grafting. Step height measurements of grafted probes could be performed on SiO₂ leading to an apparent thickness of around 3.7 ± 1.0 nm. After hybridization, on the granular surface of SnO₂, by coupling AFM with SEM FEG analyses, dispersed and well-resolved groups of gold nanoparticles linked to DNA duplexes could be observed. Their density varied from 6.6 ± 0.3 × 10¹⁰ to 2.3 ± 0.3 × 10¹¹ dots cm⁻². On the contrary, on smooth SiO₂ surface, the DNA duplexes behave like a dense carpet of globular structures with a density of 2.9 ± 0.5 × 10¹¹ globular structures cm⁻².     

Polymer-templated mesoporous carbons synthesized in the presence of nickel nanoparticles, nickel oxide nanoparticles, and nickel nitrate

Mesoporous carbon composites, containing nickel and nickel oxide nanoparticles, were obtained by soft-templating method. Samples were synthesized under acidic conditions using resorcinol and formaldehyde as carbon precursors, poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) triblock co-polymer Lutrol F127 as a soft template and nickel and nickel oxide nanoparticles, and nickel nitrate as metal precursors. In addition, a one set of samples was obtained by impregnation of mesoporous carbons with a nickel nitrate solution followed by further annealing at 400 °C. Wide angle X-ray powder diffraction along with thermogravimetric analysis proved the presence of nickel nanoparticles in the final composites obtained using nickel and nickel oxide nanoparticles, and Ni(NO₃)₂ solution. Whereas, the impregnation of carbons with a nickel nitrate solution followed by annealing at 400 °C resulted in needle-like nickel oxide nanoparticles present inside the composites’ pores. Low-temperature (−196 °C) nitrogen physisorption, X-ray powder diffraction, and thermogravimetric analysis confirmed good adsorption and structural properties of the synthesized nickel-carbon composites, in particular, the samples possessed high surface areas (>600 m²/g), large total pore volumes (>0.50 cm³/g), and maxima of pore size distribution functions at circa 7 nm. It was found that the composites were partially graphitized during carbonization process at 850 °C. The samples are stable in an air environment below temperature of 500 °C. All these features make the synthesized nickel-carbon composites attractive materials for adsorption, catalysis, energy storage, and environmental applications.     

Zinc-ion implanted and deposited titanium surfaces reduce adhesion of Streptococccus mutans

While titanium (Ti) is a commonly used dental implant material with advantageous biocompatible and mechanical properties, native Ti surfaces do not have the ability to prevent bacterial colonization. The objective of this study was to evaluate the chemical composition and bacterial adhesive properties of zinc (Zn) ion implanted and deposited Ti surfaces (Zn-PIIID-Ti) as potential dental implant materials. Surfaces of pure Ti (cp-Ti) were modified with increasing concentrations of Zn using plasma immersion ion implantation and deposition (PIIID), and elemental surface compositions were characterized by X-ray photoelectron spectrometry (XPS). To evaluate bacterial responses, Streptococcus mutans were seeded onto the modifiedTi surfaces for 48 h and subsequently observed by scanning electron microscopy. Relative numbers of bacteria on each surface were assessed by collecting the adhered bacteria, reculturing and counting colony forming units after 48 h on bacterial grade plates. Ti, oxygen and carbon elements were detected on all surfaces by XPS. Increased Zn signals were detected on Zn-PIIID-Ti surfaces, correlating with an increase of Zn-deposition time. Substantial numbers of S. mutans adhered to cp-Ti samples, whereas bacterial adhesion on Zn-PIIID-Ti surfaces signficantly decreased as the Zn concentration increased (p < 0.01). In conclusion, PIIID can successfully introduce Zn onto a Ti surface, forming a modified surface layer bearing Zn ions that consequently deter adhesion of S. mutans, a common bacterium in the oral environment.     

Surface studies of 2,4-pentanedione on γ-Al2O3/NiAl (1 0 0) and NiAl (1 0 0)

The chemical compound 2,4-pentanedione (Hacac) has been shown to etch the oxidized metal surfaces metals such as copper and nickel, but not their unoxidized surfaces. Here it is shown that on the γ-Al₂O₃/NiAl (1 0 0) surface (oxidized NiAl (1 0 0)) etching of aluminum occurs at 170 K and 750 K. Reflection-absorption infrared spectroscopy (RAIRS) is used to show that Hacac binds to both the clean, metallic and oxidized surfaces, but decomposition and combustion products dominate on the metallic surface and no etching occurs. The binding process that involves a deprotonation reaction of the enol species was identified by redshift in the carbonyl peaks and the appearance of an Al-H peak observed in the IR spectrum. The implication of these results is that there is both an unusual low temperature and high temperature etching of the alumina by bound acac.     

First-principles investigation of the electronic properties of niobium and molybdenum mononitride surfaces

Using first-principles calculations we investigated the electronic properties of niobium and molybdenum mononitride (NbN and MoN, respectively) surfaces and their dependence on the surface orientation and termination. Work functions calculated for polar surfaces strongly depend on the surface termination, with nitrogen-terminated surfaces yielding the highest value, up to 6.6 eV for the fully N-covered MoN(0 0 1) surface. The dependence of the work function on coverage for the polar surface is monotonic for nitrogen termination, but does not follow the same trend in the case of metal termination. The work function decreases by ∼2 eV for MoN from a 100% metal-terminated surface to at least 25% metal-terminated surface, and then increases rapidly between 25% and 0% metal-terminated surface to recover its nitrogen termination result. The same trend was obtained for NbN. We observed a significant increase in the charge of the surface metal atom, up to its bulk value, with decreasing metal surface coverage. Electron transfer from the metal surface atoms to the subsurface atoms can explain these submonolayer metal coverage results. Finally we found that for the non-polar surfaces, the mononitrides work functions are generally lower than the work functions of the corresponding simple metal surfaces.     

Olefin bonding mechanism and growth to (1 0 0)(2 × 1):H diamond

The bonding and growth mechanism of photochemically attached olefin molecules to (1 0 0)(2 × 1):H diamond is characterized using atomic force (AFM) and scanning tunneling microscopy (STM) experiments in combination with molecular orbital calculations. To identify growth schemas, diamond surfaces after 10, 40 and 90 min of photo-chemically stimulated growth have been characterized. These data show clearly island formation which is discussed taking into account a growth model from silicon. The island growth shows no directional properties which are attributed to arrangement and geometrical properties of hydrogen terminated carbon bonds at the surface of (1 0 0) oriented (2 × 1) reconstructed diamond.     

Studies on influence of zinc immersion and fluoride on nickel electroplating on magnesium alloy AZ91D

The effect of zinc immersion and the role of fluoride in nickel plating bath were mainly investigated in nickel electroplating on magnesium alloy AZ91D. The state of zinc immersion, the composition of zinc film and the role of fluoride in nickel plating bath were explored from the curves of open circuit potential (OCP) and potentiodynamic polarization, the images of scanning electron microscopy (SEM) and the patterns of energy dispersive X-ray (EDX). Results show that the optimum zinc film mixing small amount of Mg(OH)₂ and MgF₂ is obtained by zinc immersion for 30-90 s. The corrosion potential of magnesium alloy substrate attached zinc film will be increased in nickel plating bath and the quantity of MgF₂ sandwiched between magnesium alloy substrate and nickel coating will be reduced, which contributed to produce nickel coating with good performance. Fluoride in nickel plating bath serves as an activator of nickel anodic dissolution and corrosion inhibitor of magnesium alloy substrate. 1.0-1.5 mol dm⁻³ of F⁻ is the optimum concentration range for dissolving nickel anode and protecting magnesium alloy substrate from over-corrosion in nickel plating bath. The nickel coating with good adhesion and high corrosion resistance on magnesium alloy AZ91D is obtained by the developed process of nickel electroplating. This nickel layer can be used as the rendering coating for further plating on magnesium alloys.     

Microstructural,dielectric and magnetic behavior of spin-deposited nanocrystalline nickel–zinc ferrite thin films for microwave applications

Nanocrystalline nickel ferrite and zinc doped nickel ferrite thin films with general composition Ni_1−xZn_xFe₂O₄; x=0.0, 0.2 and 0.5 were fabricated by the spin-deposition technique. Citrate precursor method was adopted to prepare coating solution used for film deposition. This method resulted in single phase, transparent, homogeneous and crack-free nanocrystalline ferrite thin films at annealing temperature as low as 400 °C. The substrates used for film deposition were ITO-coated 7059 glass, fused quartz and Si (1 0 0). The thickness of films was found to be in the range ∼1000–5500 Å. The surface microstructure and morphology investigated by atomic force microscopy (AFM) confirmed the grain size of nickel–zinc ferrite films to be in nanometer range indicating nanocrystalline nature of the films. Dielectric properties such as the real (∈′) and imaginary parts (∈″) of complex permittivity were measured in the X-band microwave frequency region (8–12 GHz) by employing extended cavity perturbation technique. The M–H hysteresis measurements on the films annealed at 650 °C revealed narrow hysteresis curves with H_c and M_s varying for different compositions.     

Self-assembled octadecyltrichlorosilane monolayer formation on a highly hydrated silica film

A MVD silica layer that consists of a highly hydrated surface favorable for organosilane surface reaction is investigated. The MVD silica layer lacks free surface silanol groups while supporting a more extensive adsorbed water layer as compared to oxidized Si(1 0 0). Octadecyltrichlorosilane monolayers (OTS) deposited on the MVD silica layer are found to follow the same mechanisms of growth and exhibit properties comparable to those formed on oxidized Si(1 0 0) surfaces. The growth process of octadecylsiloxane films is investigated as a function of immersion time and temperature by utilizing ATR-FTIR, ellipsometry, contact angle analysis, and AFM. The MVD silica layer is shown to support an ordered interfacial water structure that is more tightly bound due to a higher degree of hydrogen bonding associated with the hydroxylated surface. The importance of interfacial water on the OTS film formation process is highlighted and the role of free OH groups on the adsorption mechanism is diminished. It is shown that OTS films can be formed on a highly hydrated surface comparable to those formed on oxidized Si(1 0 0) surfaces.     

Plasma treatment of carbon fibers: Non-equilibrium dynamic adsorption and its effect on the mechanical properties of RTM fabricated composites

The effect of oxygen plasma treatment on the non-equilibrium dynamic adsorption of the carbon fabric reinforcements in RTM process was studied. 5-Dimethylamino-1-naphthalene-sulfonylchloride (DNS-Cl) was attached to the curing agent to study the change of curing agent content in the epoxy resin matrix. Steady state fluorescence spectroscopy (FS) analysis was used to study this changes in the epoxy resin at the inlet and outlet of the RTM mould, and XPS was used to study the chemical changes on the carbon fiber surfaces introduced by plasma treatment. The interlaminar shear strength (ILSS) and flexural strength were also measured to study the effects of this non-equilibrium dynamic adsorption progress on the mechanical properties of the end products. FS analysis shows that the curing agent adsorbed onto the fiber surface preferentially for untreated carbon fiber, the curing agent content in the resin matrix maintain unchanged after plasma treatment for 3 min and 5 min, but after oxygen plasma treatment for 7 min, the epoxy resin adsorbed onto the fiber surface preferentially. XPS analysis indicated that the oxygen plasma treatment successfully increased some polar functional groups concentration on the carbon fiber surfaces, this changes on the carbon fiber surfaces can change the adsorption ability of carbon fiber to the resin and curing agent. The mechanical properties of the composites were correlated to this results.     

Wet sulfur passivation of GaSb(1 0 0) surface for optoelectronic applications

A comparative analysis of the properties of the non-passivated and S-passivated GaSb(1 0 0) surfaces has been performed through PL, AFM and RHEED characterization. The samples treated with a 1 M Na₂S aqueous solution demonstrate an increase in the 5 K PL intensity. According to AFM data, the annealing of the S-passivated GaSb(1 0 0) leads to the formation of the clean flat (1 0 0) surface. Moreover, after annealing the PL intensity of the S-passivated GaSb(1 0 0) surfaces decreases by 20%, whereas for the non-passivated samples it drops by more than a factor of 4. The method of wet sulfur passivation has shown great effectiveness in pre-epitaxial processing for LPE and MBE growth of the GaSb-related materials for optoelectronics.     

Localized grafting through chemical lift-off

In this work we present two techniques that provide localized functionalization of the surface of materials. Both lead to localized grafted thin organic films (10-200 nm). The localization is brought by a chemical lift-off process, which relies on patterned weakly bonded films as sacrificial layers, combined with electrochemical (SEEP) or chemical (GraftFast©) processes which provides the final robust pattern on the surface. Both grafting processes, which were recently described, take advantage of the redox activation of diazonium salts associated with vinylic monomers in aqueous solution, and lead to similar grafted polymer films. Thanks to the high difference in adhesion between the grafted polymer and the patterned sacrificial layer (either an ink or weakly bound self-assembled monolayers), the latter may be easily removed, which unveils uncovered areas of the substrate.     

AFM analysis of bleaching effects on dental enamel microtopography

The purpose of this in vitro study was to test a new methodology to evaluate the effects of 35% hydrogen peroxide agent on the microtopography of sound enamel using an atomic force microscope (AFM). The buccal sound surfaces of three extracted human lower incisors were used, without polishing the surfaces to maintain them with natural morphology. These unpolished surfaces were subjected to bleaching procedure with 35% hydrogen peroxide that consisted of 4 applications of the bleaching agent on enamel surfaces for 10 min each application. Surface images were obtained in a 15 μm × 15 μm area using an AFM. The roughness (Ra and RMS) and the power spectral density (PSD) were obtained before and after the bleaching treatment. As results we could inquire that the PSD analyses were very suitable to identifying the morphological changes on the surfaces, while the Ra and RMS parameters were insufficient to represent the morphological alterations promoted by bleaching procedure on enamel. The morphological wavelength in the range of visible light spectrum (380-750 nm) was analyzed, showing a considerable increase of the PSD with the bleaching treatment.     

Dynamic barrier height modulation analysis of metal-insulator-semiconductor junctions built on silicon surfaces modified by covalent organic layers

Aim of this paper is to validate a modified Schottky barrier model accounting for the electrical properties of metal - self-assembled layer - semiconductor structures. To this end, the effect of the dynamic modulation of the dipole moment of the organic layer was studied. The system was a junction built on Si(1 0 0) surfaces modified by grafting an organic layer by wet chemistry reactions. As the metallic electrode, a thin, porous gold layer was deposited, enabling gas diffusion through it. In such a geometry, a polar gas was allowed to adsorb onto the Si surface, and the variation of the barrier height could be measured and correlated with the dipole moment of the gas molecule and its partial pressure.