Liquid chromatographic determination of cis-platin as platinum(II) in pharmaceutical preparation, serum and urine samples of cancer patients

Spectrophotometric and high performance liquid chromatographic (HPLC) methods have been developed for the determination of cis-platin and carboplatin based on the pre-column derivatization of platinum(II) with 2-acetylpyridine-4-phenyl-3-thiosemicarbazone. The complex was extracted in chloroform with molar absorptivity of 2.2 × 10⁴ L mol⁻¹ cm⁻¹ at 380 nm. The complex eluted from a Phenomenex C-18 (150 mm × 4.6 mm i.d.) column with methanol:water:acetonitrile:tetrabutyl ammonium bromide (1 mM) (44:30:25:1, v/v/v/v) with a flow rate of 1 ml/min and UV detection at 260 nm. Ruthenium(IV) and selenium(IV) also separated completely. The linear calibration curve was with 0.5-12.5 μg/ml and detection limit of 10 ng/ml platinum(II).The analysis of cis-platin and carboplatin injections by spectrophotometric and HPLC methods indicated relative standard deviation (R.S.D.) of 0.66-2.1%. The method was used for the determinations of cis-platin in serum and urine of cancer patients after chemotherapy and platinum contents were found 148-444 and 50-90 ng/ml with R.S.D. of 0.3-3.0 and 0.6-2.4% for the serum and urine, respectively. The recovery of platinum(II) from serum was 97% with R.S.D. 2.2%.     

Determination of lamivudine and zidovudine in binary mixtures using first derivative spectrophotometric, first derivative of the ratio-spectra and high-performance liquid chromatography-UV methods

Three methods are presented for the simultaneous determination of lamivudine and zidovudine. The first method depends on first derivative UV spectrophotometry, with zero-crossing and peak-to-base measurement. The first derivative amplitudes at 265.6 and 271.6 nm were selected for the assay of lamivudine and zidovudine, respectively. The second method depends on first derivative of the ratio-spectra by measurements of the amplitudes at 239.5 and 245.3 nm for lamivudine and 225.1 and 251.5 nm for zidovudine. Calibration graphs were established for 1-50 μg/ml for lamivudine and 2-100 μg/ml for zidovudine. In the third method (HPLC), a reversed-phase column with a mobile phase of methanol:water:acetonitrile (70:20:10 (v/v/v)) at 0.9 ml/min flow rate was used to separate both compounds with a detection of 265.0 nm. Linearity was obtained in the concentration range of 0.025-50 μg/ml for lamivudine and 0.15-50 μg/ml for zidovudine. All of the proposed methods have been extensively validated. These methods allow a number of cost and time saving benefits. The described methods can be readily utilized for analysis of pharmaceutical formulations. There was no significant difference between the performance of all of the proposed methods regarding the mean values and standard deviations. The described HPLC method showed to be appropriate for simultaneous determination of lamivudine and zidovudine in human serum samples.     

Enantiospecific resolution of rabeprazole by liquid chromatography on amylose-derived chiral stationary phase using photo diode array and polarimetric detectors in series

A simple and rapid liquid chromatographic method for enantioselective separation and determination of R-(+) and S-(−) enantiomers of rabeprazole in drugs and pharmaceuticals using photo diode array (PDA) and polarimetric detectors connected in series was developed. Chiralpak AD-H (250 mm × 4.6 mm) 5 μm column packed with amylose tris(3,5-dimethylphenyl carbamate) as a stationary phase and the mobile phase containing n-hexane:ethanol:2-propanol(75:15:10, v/v/v) in an isocratic mode has yielded baseline separation with resolution greater than 3.0 at 40 °C. Effects of ethanol, 2-propanol and temperature on separation were studied for optimum resolution. Lansoprazole sulphone was used as an internal standard (IS) for quantitative determination of individual enantiomers in bulk drugs as well as pharmaceutical formulations. The method was validated in terms of accuracy, precision and linearity according to ICH guidelines. The linearity of the method was studied in the range of 0.5-50 μg/ml and the r² was >0.9997. The inter- and intra-day precision of assay were determined (R.S.D. < 1%) and the recoveries were in the range of 99.63-100.22% with <1% R.S.D. The limits of detection (LOD) and quantification (LOQ) were 0.02 μg/ml and 0.07 μg/ml for both the enantiomers, respectively.     

Simultaneous determination of cefotaxime and desacetylcefotaxime in real urine sample using voltammetric and high-performance liquid chromatographic methods

Two rapid, accurate and sensitive methods are developed and validated for the quantitative simultaneous determination of cefotaxime (CFX) and its active metabolite desacetylcefotaxime (DCFX) in urine.Based on the previous results which showed the four electron reduction of CFX at ≈ −0.5 V, and the new findings that DCFX reduction occurred at more positive potential (−0.23 V), the new adsorptive stripping differential pulse voltammetric (AdSDPV) method was developed for determination of CFX in the presence of DCFX. Linear responses were observed over a wide concentration range (0.07-0.52 μg/ml for CFX and 0.22-1.3 μg/ml for DCFX) in urine.The second assay involves subsequent separation on a reversed-phase HPLC column, with ultraviolet detection at 262 nm. Retention times were 4.057 and 1.960 min for CFX and DCFX, respectively. Linear responses were observed over a wide range, 0.55-6.60 μg/ml for CFX and 1.10-11.00 μg/ml for DCFX, in urine.The statistical evaluation for both methods was examined by means of within-day repeatability (n = 5) and day-to-day precision (n = 3) and was found to be satisfactory with high accuracy and precision.     

Evaluation of V, Ir, Ru, V-Ir, V-Ru, and W-V as permanent chemical modifiers for the determination of cadmium, lead, and zinc in botanic and biological slurries by electrothermal atomic absorption spectrometry

Permanent modifiers (V, Ir, Ru, V-Ir, V-Ru, and W-V) thermally coated on to platforms of pyrolytic graphite tubes were employed for the determination of Cd, Pb, and Zn in botanic and biological slurries by electrothermal atomic absorption spectrometry (ETAAS). Conventional Pd + Mg(NO₃)₂ modifier mixture was also used for the determination of analytes in slurries and digested samples. Optimum masses and mass ratios of permanent modifiers for Cd, Pb, and Zn in slurry sample solutions were investigated. The 280 μg of V, 280 μg of V + 200 μg of Ir, 280 μg of V + 200 μg of Ru or 240 μg of W + 280 μg of V in 0.2% (v/v) Triton X-100 plus 0.5% (v/v) HNO₃ mixture was found as efficient as 5 μg of Pd + 3 μg of Mg(NO₃)₂ modifier mixture for obtaining thermal stabilization, and for obtaining best recoveries. Optimization conditions of analytes, such as pyrolysis and atomization temperature, characteristic masses and detection limits, and atomization and background peak profiles were studied with permanent and 5 μg of Pd + 3 μg of Mg(NO₃)₂ conventional modifiers and compared with each other. The permanent V-Ir, V-Ru, and W-V modifiers remained stable for approximately 250-300 firings when 20 μl of slurries and digested samples were delivered into the atomizer. In addition, the mixed permanent modifiers increase the tube lifetime by 50-95% when compared with untreated platforms. The characteristic masses and detection limits of analytes (dilution factor of 125 ml g⁻¹) obtained with V-Ir based on integrated absorbance as example for 0.8% (m/v) slurries were 1.0 pg and 3 ng g⁻¹ for Cd, 18 pg and 17 ng g⁻¹ for Pb, and 0.7 pg and 4 ng g⁻¹ for Zn, respectively. The results of analytes obtained by employing V-Ir, V-Ru, and W-V permanent modifier mixtures in botanic and biological certified and standard reference materials were in agreement with the certified values of reference materials.     

Determination of vanadium in human hair slurries by electrothermal atomic absorption spectrometry

This work describes an analytical procedure for vanadium determination in human hair slurries by electrothermal AAS using longitudinal heating (LHGA) and transversal heating (THGA) graphite furnace atomizers. The samples were powdered using cryogenic grinding and the hair slurries containing 0.2% (m/v) were prepared in three different media for determination of vanadium: 0.14 mol L⁻¹ HNO₃, 0.1% (v/v) Triton X-100 and 0.1% (v/v) water soluble tertiary amines (CFA-C, pH 8). The limits of detection (LOD), limits of quantification (LOQ), and characteristic masses obtained were 0.28, 0.95 μg L⁻¹ and 35 pg (LHGA) and 0.34, 1.13 μg L⁻¹ and 78 pg (THGA), respectively. The accuracy of the analytical results obtained by the proposed procedure in both equipments was confirmed by a paired t-test at the 95% confidence level and compared with a conventional procedure based on acid digestion.     

Cloud point extraction preconcentration for capillary electrophoresis of metal ions

The application of the cloud point extraction (CPE) technique for capillary electrophoresis (CE) determination of metal ions was demonstrated using Cu(II) and Co(II) as model metal ions. The preconcentration of Cu(II) and Co(II) in aqueous solution was achieved by CPE with 1-(2-pyridylazo)-2-naphthol (PAN) as the chelating agent and Triton X-114 as the extractant. Baseline separation of the PAN chelates of Cu(II) and Co(II) was realized by CE with a photodiaode array detector in a  μm i.d. fused-silica capillary at 17 kV. A 50 mM NH₄Ac buffer solution (pH 8.0) containing 0.2 mM of PAN in 80% (v/v) of acetonitrile and 20% (v/v) doubly deionized water (DDW) was used as the separation medium to avoid the adsorption of hydrophobic substances and nonionic surfactant Triton X-114 onto the inner surface of the separation capillary, ensuring the separation efficiency and reproducibility. The precision (relative standard deviation (R.S.D.), n=5) for five replicate injections of a mixture of 20 μg/l of Co(II) and Cu(II) were 0.74 and 1.8% for the migration time, 3.1 and 0.64% for the peak area measurement, respectively. The apparent concentration factor, which is defined as the concentration ratio of the analyte in the final diluted surfactant-rich extract ready for CE separation and in the initial solution, was 15.9 for Co(II) and 16.3 for Cu(II). The linear concentration range was from 3 to 100 μg/l for both Co(II) and Cu(II). The detection limits of Co(II) and Cu(II) were 0.12 and 0.26 μg/l, respectively. The developed method was successfully applied to the determination of Co(II) and Cu(II) in tap water, snow water, and flavor wines.     

On-line preconcentration and speciation of arsenic by flow injection hydride generation atomic absorption spectrophotometry

A flow injection-column preconcentration-hydride generation atomic absorption spectrophotometric (FI-column-HGAAS) method was developed for determining μg/l levels of As(III) and As(V) in water samples, with simultaneous preconcentration and speciation. The speciation scheme involved determining As(V) at neutral pH and As(III + V) at pH 12, with As(III) obtained by difference. The enrichment factor (EF) increased with increase in sample loading volume from 2.5 to 10 ml, and for preconcentration using the chloride-form anion exchange column, EFs ranged from 5 to 48 for As(V) and 4 to 24 for As(III + V), with corresponding detection limits of 0.03-0.3 and 0.07-0.3 μg/l. Linear concentration range (LCR) also varied with sample loading volume, and for a 5-ml sample was 0.3-5 and 0.2-8 μg/l for As(V) and As(III + V), respectively. Sample throughput, which decreased with increase in sample volume, was 8-17 samples/h. For the hydroxide-form column, the EFS for 2.5-10 ml samples were 3-23 for As(V) and 2-15 for As(III + V), with corresponding detection limits of 0.07-0.4 and 0.1-0.5 μg/l. The LCR for a 5-ml sample was 0.3-10 μg/l for As(V) and 0.2-20 μg/l for As(III + V). Sample throughput was 10-20 samples/h. The developed method has been effectively applied to tap water and mineral water samples, with recoveries ranging from 90 to 102% for 5-ml samples passed through the two columns.     

Separation/preconcentration and determination of vanadium with dispersive liquid-liquid microextraction based on solidification of floating organic drop (DLLME-SFO) and electrothermal atomic absorption spectrometry

A novel dispersive liquid-liquid microextraction based on solidification of floating organic drop (DLLME-SFO) for separation/preconcentration of ultra trace amount of vanadium and its determination with the electrothermal atomic absorption spectrometry (ETAAS) was developed. The DLLME-SFO behavior of vanadium (V) using N-benzoyl-N-phenylhydroxylamine (BPHA) as complexing agent was systematically investigated. The factors influencing the complex formation and extraction by DLLME-SFO method were optimized. Under the optimized conditions: 100 μL, 200 μL and 25 mL of extraction solvent (1-undecanol), disperser solvent (acetone) and sample volume, respectively, an enrichment factor of 184, a detection limit (based on 3S_b/m) of 7 ng L⁻¹ and a relative standard deviation of 4.6% (at 500 ng L⁻¹) were obtained. The calibration graph using the preconcentration system for vanadium was linear from 20 to 1000 ng L⁻¹ with a correlation coefficient of 0.9996. The method was successfully applied for the determination of vanadium in water and parsley.     

Catalytic adsorptive stripping voltammetric measurements of trace vanadium at bismuth film electrodes

Bismuth-coated glassy carbon electrodes have been successfully applied for catalytic adsorptive stripping voltammetric measurements of low levels of vanadium(V) in the presence of chloranilic acid (CAA) and bromate ion. The new protocol is based on the accumulation of the vanadium-chloranilic acid complex from an acetate buffer (pH 5.5) solution at a preplated bismuth film electrode held at −0.35 V (versus Ag/AgCl), followed by a square-wave voltammetric scan. Factors influencing the adsorptive stripping performance, including the CAA and bromate concentrations, solution pH, and accumulation potential or time have been optimized. The response compares favorably with that observed at mercury film electrodes. A linear response is observed over the 5-25 μg/L concentration range (2 min accumulation), along with a detection limit of 0.20 μg/L vanadium (10 min accumulation). High stability is indicated from the reproducible response of a 50 μg/L vanadium solution (n = 25; R.S.D. = 3.1%). Applicability to a groundwater sample is illustrated.     

Determination of tin and titanium in soils, sediments and sludges using electrothermal atomic absorption spectrometry with slurry sample introduction

Fast-heating programmes for determining titanium and tin in soils, sediments and sludges using electrothermal atomic absorption spectrometry (ETAAS) with slurry sampling are developed. For titanium determination, suspensions are prepared by weighing 5-40 mg of sample and adding 25 ml of a solution containing 50% (v/v) concentrated hydrofluoric acid. For tin determination, suspensions are prepared by weighing up to 300 mg of sample and then adding 1 ml of a solution containing 25% (v/v) concentrated hydrofluoric acid. Palladium (30 μg) and ammonium dihydrogen phosphate (7% w/v) are used as matrix modifiers for titanium and tin, respectively. Prior mild heating in a microwave oven is recommended for titanium determination. Calibration is carried out using aqueous standards. The tin and titanium contents of a number of samples obtained by using the slurry approach agree with those obtained by means of a procedure based on the total dissolution of the samples using microwave oven digestion. The reliability of the procedures is also confirmed by analysing several certified reference materials.     

Validated liquid chromatography method for assay of tizanidine in drug substance and formulated products

A new isocratic stability indicating HPLC method for determination of tizanidine in drug substance and formulated products is described. Chromatographic separation of tizanidine from the related substances and degraded products was achieved with a Hypersil CN column ( mm, 5 μm) using a mobile phase comprising a mixture of an ion-pairing solution of heptanesulphonic acid sodium salt (HAS), methanol and acetonitrile (50:57:18 (v/v)) within 10 min. The flow-rate was 1.0 ml/min and detection was made at 227 nm. The method has good selectivity towards tizanidine, related substances and degraded products. Limits of quantitation for tizanidine and its synthetic intermediates were determined, ranging from 0.051 to 0.54 μg/ml. The linearity range was found to be 2-20 μg/ml (r=0.9998, n=5). Mean recovery for tizanidine from the tablets was from 99.5 to 99.8%. Precision of the method was 1.0% (n=9). The method can be used for routine analysis and the quality control of tizanidine drug substance and its formulated products.     

Development of new adsorbent chitin for column preconcentration and spectrophotometric trace determination of Ziram and Zineb in synthetic, commercial samples and food-stuffs

A procedure has been developed for the determination of zinc(II) bis(dimethyldithiocarbamate) (Ziram) or zinc(II) ethylenebisdithiocarbamate (Zineb) present in a large volume of aqueous solution after preconcentration on a column using chitin-1-(2′pyridylazo)-2-naphthol (PAN) as adsorbent. Ziram/Zineb are quantitatively retained on the column as Zn-PAN complex in the pH range 9.0-11.0 and at a flow rate of 1-8 ml/min. Complex adsorbed on chitin was eluted from the column with dimethylformamide (DMF) and absorbance of the eluate was measured at 550 nm against a reagent blank. Beer's law is obeyed over the concentration range 5.3-55.8 μg of Ziram and 6.8-49.0 μg of Zineb in 25 ml of the final DMF solution. Ten replicate determinations on a sample solution containing 45.22 μg of Ziram or 40.86 μg of Zineb gave a mean absorbance of 0.30 with a relative standard deviation 1.6 and 1.8%, respectively. The interference of various ions has been studied. Many alkali metals and metal salts do not interfere. The method has been employed to the determination of Ziram and Zineb in commercial samples and in various foodstuffs and the results were compared with the earlier reported methods.     

Trace analysis of vanadium as pentavalent vanadium using differential pulse polarography with a coupled catalytic homogeneous reaction

The differential pulse polarographic determination of the vanadium (V) ion coupled with a catalytic homogeneous reaction was carried out in a system containing the vanadium (V)-PAR complex and an oxidant in acetic/acetate buffer. On addition of the powerful oxidant, sodium bromate, the peak current for the reduction of the vanadium (V) complex was increased significantly by about 21 times. A calibration plot was found to be linear in the concentration range 0.05–0.25 g/ml and the detection limit was 5 ng/ml.     

Analysis of Metal Ions in Environmental Samples - III Synergistic Determination of Vanadium (V) As its Mixed Complex with N-0-Methoxyphenyl-2-Thenohydroxamic Acid and 3-(0-Carboxyphenyl)-1-Phenyltriazine-N-0Xide

Abstract

A highly sensitive, selective, and rapid method for the spectrophotometry determination of vanadium(V) at trace levels is described. The method is based on the selective extraction of vanadium(v) from strongly acidic (3–6 M hydrochloric acid) met ium with solution of N-0-methoxyphenyl-2- thenohydroxamic acid (0MTHA) in chloroform. The extract is then equilibrated with 3-(0-carboxyohenyl)-1-phenyltriazine-N-oxide(CPPTNO) at pH ? 1.5 and the resulting colour is measured at 445 nm. The colour system obeys Beer's law over the range 0–20 -μg/ml of vanadium; the molar absorptivityat the wavelength of maximum absorption (445 nm), and the Sandell sensitivity of the method are 1.1 × 10⁴1. mole^?1 cm^?1 and 0.005 μg/ml respectively.     

Separation and simultaneous determination of niobium and tantalum in steel by reversed-phase high-performance liquid chromatography using 2-(2-pyridylazo)-5-diethylamino phenol as a pre-column derivatizing reagent

A method for the simultaneous determination of Nb and Ta in steel and alloy by reversed-phase high-performance liquid chromatography (RP-HPLC) was proposed. 2-(5-Bromo-2-pyridylazo)-5-diethylamino phenol (5-Br-PADAP) was used as a pre-column chelating agent to form a ternary complex with Nb(V) and Ta(V) and tartaric acid. The ternary complexes of Nb(V) and Ta(V) were eluted within 8 min on a C₁₈ column with a mobile phase of methanol-water (55:45, v/v) containing 10 mmol l⁻¹ acetate buffer (pH3.5) and determined with spectrophotometric detection at 598 nm. The detection limits for Nb(V) and Ta(V) were 0.60 and 0.72 μg l⁻¹, respectively, when the ratio of signal-to-noise is 3. The proposed method was used to analyze Nb and Ta in cast iron, alloy and stainless steel.     

Determination of thyroxine enantiomers in pharmaceutical formulation by high-performance liquid chromatography-mass spectrometry with precolumn derivatization

A sensitive and specific liquid chromatography-electrospray ionization-mass spectrometry (LC-ESI-MS) method for the separation and analysis of d- and l-thyroxine was developed using R(−)/S(+)-4-(3-isothiocyanatopyrrolidin-1-yl)-7-(N,N-dimethylaminosulfonyl-2,1,3-benzoxadiazole, [R(−)/S(+)-DBD-PyNCS] as a chiral derivatization reagents. The T₄ derivatives with R(−)-DBD-PyNCS were efficiently separated on a reversed-phase column with water-acetonitrile containing 0.1% formic acid (41:59, v/v) as the eluent and analyzed using ESI-MS with negative selected ion monitoring (SIM) mode. The calibration curves of both the d-T₄ and l-T₄ were linear over the concentration range of 0.13-13 μg/ml. The detection limits (S/N = 3) were 28 ng/ml for d-T₄ and 40 ng/ml for l-T₄, respectively. The relative standard deviations (RSD, n = 5) were less than 3.6% at 1.3 μg/ml for both T₄ enantiomers. The proposed method was applied to the determination of l-T₄ enantiomer in a pharmaceutical formulation.     

Determination of ethambutol by ion-pair reversed phase liquid chromatography with UV detection

An ion-pair reversed phase liquid chromatography method for the antituberculosis drug ethambutol hydrochloride was developed using sodium 1-heptanesulfonate (4.0 mg/ml) as an ion-pairing (IP) reagent. To enable detection of the ethambutol with a UV detector without sample pretreatment, the pH 4.5 aqueous tetrahydrofuran (THF) (25%, v/v) mobile phase contained 1.0 mM Cu(II), which forms a UV-absorbing complex with the analyte. At a column temperature of 35 °C, ethambutol gives a symmetrical peak with a retention time of 5 min. Chromatographic conditions were optimized through study of the effects of mobile phase composition and pH, Cu(II) and IP reagent concentration, and column temperature. The method is shown to be simple, precise, efficient, robust, linear up to at least 0.25 mg/ml, and to have a limit of quantitation of 6 μg/ml.     

Determination of As(III) and As(V) in soils using sequential extraction combined with flow injection hydride generation atomic fluorescence detection

An analytical procedure for determination of As(III) and As(V) in soils using sequential extraction combined with flow injection (FI) hydride generation atomic fluorescence spectrometry (HG-AFS) was presented. The soils were sequentially extracted by water, 0.6 mol l⁻¹ KH₂PO₄ solution, 1% (v/v) HCl solution and 1% (w/v) NaOH solution. The arsenite (As(III)) in extract was analyzed by HG-AFS in the medium of 0.1 mol l⁻¹ citric acid solution, then the total arsenic in extract was determined by HG-AFS using on-line reduction of arsenate with l-cysteine. The concentration of arsenate (As(V)) was calculated by the difference. The optimum conditions of extraction and determination were studied in detail. The detection limit (3σ) for As(III) and As(V) were 0.11 and 0.07 μg l⁻¹, respectively. The relative standard deviation (R.S.D.) was 1.43% (n=11) at the 10 μg l⁻¹ As level. The method was applied in the determination of As(III) and As(V) of real soils and the recoveries of As(III) and As(V) were in the range of 89.3-118 and 80.4-111%, respectively.