Hydrothermal Preparation of Photoluminescent Graphene Quantum Dots Characterized Excitation‐Independent Emission and its Application as a Bioimaging Reagent

Zero‐dimensional photoluminescent (PL) graphene quantum dots (GQDs) that can be used as the cell‐imaging reagent are prepared by a hydrothermal route using the graphene oxide (GO) as the carbon source. Under the optimized hydrothermal conditions, an initial hydrogen peroxide concentration of 0.5 mg mL^?1 at 180 °C for 120 min, the GO sheets can be cut into nanocrystals with lateral dimensions in the range of 1.5–5.5 nm and an average thickness of around 1.1 nm. The as‐prepared GQDs exhibit an abundance of hydrophilic hydroxy and carboxyl groups and emit bright blue luminescence with up‐conversion properties in a water solution at neutral pH. Most interestingly, they indicate excitation‐independent emission characteristics, and the surface state is demonstrated to have a key role in the PL properties. The fluorescence quantum yield of the GQDs is tested to be around 6.99% using quinine sulfate as a standard. In addition, the as‐prepared GQDs can enter into HeLa cells easily as a fluorescent imaging reagent without any further functionalization, indicating they are aqueous stability, biocompatibility, and promising for potential applications in biolabeling and solution state optoelectronics.     

Functionalized CdS nanospheres and nanorods

Functionalized nanoparticles are discussed. Surfaces of CdS:Mn/ZnS core/shell nanospheres (Qdots) were converted from hydrophobic to hydrophilic by growth of a SiO₂ shell. The colloidal dispersion was stabilize by adding a surfactant with a negative surface charge, and a cell-penetrating-peptide, TAT, was attached through a primary amine group. The TAT functionalized Qdots were shown to pass the blood-brain-barrier and luminescence in the infused half of the brain.In addition, nanorods of S²⁻ rich CdS were synthesized by reaction of excess S with Cd precursors in the presence of ethylene diamine. The photoluminescence (PL) peak from the S²⁻ rich CdS nanorods was broad with a maximum at ∼710 nm, which was 40 nm longer in wavelength than the PL peak from Cd²⁺ rich CdS (∼670 nm) nanorods. The influence of surface electron or hole trap states on the luminescent pathway of CdS nanorods were used to explain these shifts in wavelength. Nanocrystals of Au with ∼2 nm diameters were grown on S²⁻ rich surfaces of CdS nanorods. Significant quenching of photoluminescence was observed from Au nanocrystals on CdS nanorods due to interfacial charge separation. Charge separation by Au nanocrystals on CdS resulted in enhanced UV photocatalytic degradation of Procion red mix-5B (PRB) dye in aqueous solution.     

Characterization of size, surface charge, and agglomeration state of nanoparticle dispersions for toxicological studies

Characterizing the state of nanoparticles (such as size, surface charge, and degree of agglomeration) in aqueous suspensions and understanding the parameters that affect this state are imperative for toxicity investigations. In this study, the role of important factors such as solution ionic strength, pH, and particle surface chemistry that control nanoparticle dispersion was examined. The size and zeta potential of four TiO₂ and three quantum dot samples dispersed in different solutions (including one physiological medium) were characterized. For 15 nm TiO₂ dispersions, the increase of ionic strength from 0.001 M to 0.1 M led to a 50-fold increase in the hydrodynamic diameter, and the variation of pH resulted in significant change of particle surface charge and the hydrodynamic size. It was shown that both adsorbing multiply charged ions (e.g., pyrophosphate ions) onto the TiO₂ nanoparticle surface and coating quantum dot nanocrystals with polymers (e.g., polyethylene glycol) suppressed agglomeration and stabilized the dispersions. DLVO theory was used to qualitatively understand nanoparticle dispersion stability. A methodology using different ultrasonication techniques (bath and probe) was developed to distinguish agglomerates from aggregates (strong bonds), and to estimate the extent of particle agglomeration. Probe ultrasonication performed better than bath ultrasonication in dispersing TiO₂ agglomerates when the stabilizing agent sodium pyrophosphate was used. Commercially available Degussa P25 and in-house synthesized TiO₂ nanoparticles were used to demonstrate identification of aggregated and agglomerated samples.     

微波辐射法制备水溶性CdTe量子点及其光谱学研究

用半胱胺作为稳定剂,采用微波辐射加热的方法快速合成了水溶性的CdTe量子点。吸收光谱和荧光光谱表明所合成的量子点具有优异的发光性能。透射电子显微镜(TEM)和X射线粉末衍射(XRD)表征了量子点的结构和粒径分布。通过荧光发射光谱研究了反应温度、加热时间和配体浓度对量子点晶体生长速度的影响。反应温度提高或稳定剂半胱胺的浓度减小,纳米晶体的生长速度加快。在一定温度下,随着反应时间的延长,量子点发射波长发生红移。与传统的水相回流方法相比微波加热制备水溶性的CdTe量子点具有反应速度快、得到的量子点尺寸分布均匀、半峰宽较窄和量子产率较高等特点。     

Enhancement of the fluorescence of triphenylmethane dyes caused by their interaction with nanoparticles from β-diketonate complexes

We have studied the absorption and fluorescence spectra of Malachite Green and Crystal Violet in aqueous and alcoholic-aqueous solutions in which nanoparticles from Ln(III) and Sc(III) diketonates are formed at concentrations of complexes in a solution of 5–30 μM. We have shown that, if the concentrations of the dyes in the solution are lower than 0.5 μM, dye molecules are incorporated completely into nanoparticles or are precipitated onto their surface. The fluorescence intensity of these incorporated and adsorbed Malachite Green and Crystal Violet molecules increases by several orders of magnitude compared to the solution, which takes place because of a sharp increase in the fluorescence quantum yields of these dyes and at the expense of the sensitization of their fluorescence upon energy transfer from β-diketonate complexes entering into the composition of nanoparticles. We have shown that, if there is no concentration quenching, the values of the fluorescence quantum yield of the Crystal Violet dye incorporated into nanoparticles and adsorbed on their surface vary from 0.06 to 0.13, i.e., are close to the fluorescence quantum yield of this dye in solid solutions of sucrose acetate at room temperature. The independence of the fluorescence quantum yield of Crystal Violet on the morphology of nanoparticles testifies to a high binding constant of complexes and the dye. The considerable fluorescence quantum yields of triphenylmethane dyes in nanoparticles and sensitization of their fluorescence by nanoparticle-forming complexes make it possible to determine the concentration of these dyes in aqueous solutions by the luminescent method in the range of up to 1 nM.     

Self-assembly of doped semiconductor nanocrystals leading to the formation of highly luminescent nanorods

Meso-scale self-assembly of doped semiconductor nanocrystals leading to the formation of monocrystalline nanorods showing enhanced photo- and electro-luminescence properties are reported. Polycrystalline ZnS: Cu⁺-Al³⁺ nanoparticles of zinc-blended (cubic) structure with an average size of ∼4 nm were aggregated in aqueous solution and grown into nanorods of length ∼400 nm and aspect ratio ∼12. Transmission electron microscope (TEM) images indicate crystal growth mechanisms involving particle-to-particle oriented-attachment assisted by sulphur-sulphur catenation leading to covalent-linkage. The nanorods exhibit self-assembly dependant luminescence properties such as quenching of the lattice defect-related emissions accompanied by enhancement of dopant-related emission, efficient low-voltage electroluminescence (EL) and super-linear voltage-brightness EL characteristics. This study demonstrates the technological importance of aggregation based self-assembly in doped semiconductor nanosystems.     

Magnetorheology of colloidal dispersion containing Fe nanoparticles synthesized by the arc-plasma method

Spherical crystalline Fe nanoparticles, ∼100 nm in diameter, were synthesized under Ar-50% H₂ arc-plasma. These nanoparticles were dispersed in silicone oil after silane treatment on as-grown thin oxide layer (∼2 nm) to make their surfaces hydrophobic. The resulting Fe nanoparticles exhibited a high saturation magnetization of ∼190 emu/g at room temperature. The static magnetorheological behavior was measured for the colloidal dispersion (solid concentration: 15 vol%) at room temperature under magnetic flux densities of 0-0.3 T, using a parallel-plate-type commercial rheometer. The yield stress continuously increased with magnetic flux density, demonstrating the Bingham plastic behavior. Moreover, subjecting the sample to a magnetic flux density of 0.3 T increased the yield stress by ∼10². Additionally, the colloidal dispersion exhibited good stability against sedimentation.     

曲通X-100的荧光光谱与荧光量子产率

报道了曲通X-100(TX)水溶液的荧光光谱与荧光量子产率。实验发现,在强酸性条件下,TX没有荧光,当pH ＞1时,TX有稳定的强荧光,荧光激发波长为229和275 nm,发射波长为302 nm。TX水溶液可产生共振荧光,共振荧光峰位于285 nm。在0.1～90 mg·L-1浓度范围内,TX荧光强度与浓度之间存在线性关系,检测限为0.1 mg·L-1。以L-色氨酸为参比,测得在激发波长280 nm处TX水溶液的荧光量子产率为0.121。     

Numerical simulations of sonochemical production and oriented aggregation of BaTiO3 nanocrystals

Numerical simulations of sonochemical production and oriented attachment of BaTiO₃ nanocrystals are performed in aqueous solution with pH 14. It is suggested that most significant effect of ultrasound is the dissolution of Ti-based gel in aqueous solution. It results in the dissolution-precipitation mechanism in the production of BaTiO₃ nanoparticles, while with mechanical stirring without ultrasound it is the in situ mechanism that BaTiO₃ is gradually formed on Ti-based gel. The oriented attachment of spherical BaTiO₃ nanocrystals occurs by van der Waals torque (Casimir torque). Large aggregates of nanocrystals do not attach with each other as the repulsive double layer interaction is stronger for larger aggregates. For smaller spherical nanocrystals, the alignment of the crystal axes is less accurate due to more significant rotational Brownian motion of the nanocrystals.     

Preparation of Highly Biocompatible ZnSe Quantum Dots Using a New Source of Acetyl Cysteine as Capping Agent

In this paper, we describe a facile method for preparation of ZnSe quantum dots (QDs) using an inexpensive and biocompatible source of acetyl cysteine in aqueous media. The structural properties of the ZnSe QDs have been characterized using XRD, FT-IR, and TEM techniques. The optical properties of the as-prepared QDs were found to be size-dependent, due to the strong confinement regime at relatively low refluxing time. Effect of solution pH and refluxing temperature on absorption and emission characteristics of the ZnSe QDs was studied. The empirical effective mass approximation also reveals that, both solution pH and refluxing temperature parameters would effect on ZnSe QDs growth, and increase their size. However, the influence of the solution pH was found to be more prominent. Water-solubility, high emission intensity and sub-10 nm nanocrystals size are the most essential features that suggest our synthesized aqueous-based ZnSe QDs (with a very cost-effective and biocompatible capping agent) can be utilized for biological intentions.     

Light emission from silicon nanocrystals: Probing a single quantum dot

Analysis of low-temperature photoluminescence measurements performed on single silicon nanocrystals is presented. The luminescence emission linewidth of Si nanocrystals is found to be less than thermal broadening at low temperature, confirming the atomic-like nature of their energetic states. Beside the main peak the low-temperature spectra reveal a ∼6 meV replica, the origin of which is discussed. For some of the investigated dots, we also observe a ∼60 meV transverse optical (TO) phonon replica. The regular arrangement of individual nanocrystals used in this work enables combined high-resolution transmission electron microscopy (TEM) and low-temperature photoluminescence characterization of the same single quantum dot.     

Synthesis and optical characterization of PVP and SHMP-encapsulated Mn-doped ZnS nanocrystals

Zinc sulfide semiconductor nanocrystals doped Mn²⁺ have been synthesized via a solution-based method utilizing optimum dopant concentration (4%) and employing polyvinyl pyrrolidone (PVP) and sodium hexametapolyphosphate (SHMP) as capping agents. UV-vis absorbance spectra for all of the synthesized nanocrystals show an exitonic peak at around 310 nm. The particle size and morphology were characterized by scanning electron microscopy (SEM), FT-IR, X-ray diffraction (XRD), transmission electron microscopy (TEM) and photoluminescence spectrum (PL). Diffraction data confirmed that the crystallite size is around 3-5 nm. Room temperature photoluminescence (PL) spectrum for the bare ZnS sample shows a strong band at ∼445 nm. The uncapped and capped(SHMP, PVP) ZnS:Mn²⁺ samples show a strong and broad band in the ∼580-585 nm range.     

Highly luminescent silica-coated ZnO nanoparticles dispersed in an aqueous medium

Highly luminescent silica-coated ZnO nanoparticles dispersed in an aqueous medium were synthesized using the sol-gel process. The samples prepared at various temperatures exhibited an emission peak at around 480 nm (blue color) and a quantum efficiency of 60% at maximum by the quantum confinement effect of ZnO nanoparticles, with diameters ranging from 3.1 to 3.5 nm, under ultraviolet excitation. No degradation of the quantum efficiencies and no peak shifting in the emission spectra were observed for 7 days following the preparation, which indicated no growth of ZnO nanoparticles in the aqueous medium.     

Interaction between water molecules and 3C-SiC nanocrystal surface

The influence of water permeates almost all areas including biochemistry,chemistry,physics and is particularly evident in phenomena occurring at the interfaces of solid surface such as SiC nanocrystals,which are promising nanomaterials and exhibit unique surface chemical properties.In this paper,the quantum confinement effect and stability of 3C-SiC nanocrystals in aqueous solution as well as photoluminescence properties in water suspensions with different pH values are reviewed based on design and analysis of surface structures.On this basis,the significant progress of 3C-SiC nanocrystals in efficiently splitting water into usable hydrogen is summarized and the relative mechanisms are described.In addition,the water-soluble 3C-SiC quantum dots as robust and nontoxic biological probes and labels also are introduced as well as future prospects given.     

醇热技术制备TiO2纳米晶的荧光光谱及荧光量子产率

采用钛酸四丁酯醇热技术制备了TiO2纳米晶溶胶,透射电子显微镜(TEM)照片显示其为粒径小于10nm的类球形形貌。该纳米晶在最大激发波长375nm激发下,在450nm处产生稳定的强荧光。不同浓度TiO2纳米晶的荧光光谱和吸收光谱表明,该发光带不仅受粒子量子尺寸效应的影响还与带内缺陷能级和表面态的电子跃迁有关,是三者共同作用的结果。以硫酸奎宁在激发波长313nm的荧光量子产率0.55为标准,测得TiO2纳米晶在不同激发波长下的荧光量子产率。结果表明,TiO2纳米晶在激发波长330～370nm范围内有较高的荧光量子产率(约为0.20),远高于文献报道值(10-3数量级)。据此,TiO2纳米晶有望成为一种有前途的无机纳米荧光探针。     

Two-photon spectroscopy and microscopy of II–VI semiconductor nanocrystals

We review our recent nonlinear spectroscopies of nanocrystals and synthetic efforts to improve their luminescence properties. A two-photon spectroscopic study of CdSe nanocrystals as a function of size is presented and compared with predictions from the effective mass model with spherical confinement. We also detail our efforts at improving the luminescence properties of nanocrystals which have culminated in a 50% fluorescence quantum yield for inorganic capping of some sizes of CdSe nanocrystals. Finally, we present the application of two-photon microscopy to resolve fluorescence from single nanocrystals at room temperature and cryogenic temperatures.     

Procedures for Controlling the Size, Structure and Optical Properties of CdS Quantum Dots during Synthesis in Aqueous Solution

We report an easy approach for the synthesis of CdS Quantum Dots (CdS QDs) with high luminescence and temporal stability through the reaction of Cd²⁺ and S^2- in the presence of mercaptoacetic acid (MAA) as a capping reagent in aqueous medium, under normal pressure and room temperature. The influence of several experimental variables, including temperature, pH, the Cd/S ratio and the Cd/MAA ratio, on the optical properties of the QDs obtained was studied systematically. The experimental results indicate that these variables play an important role in determining the size and state of the surface of the nanoparticles, and hence their luminescent properties and temporal stability. The general aspects of nanocrystal nucleation and growth in the synthesis of nanocrystals were studied. The best conditions for the synthesis of nanoparticles of high quality are also reported. The CdS nanocrystals obtained exhibited a narrow PL band, with reproducible room-temperature quantum yields.     

The concentration dependence of relaxation times of hydrogen proton in the aqueous solution of iron ferrite magnetic nanoparticles

By the direct coprecipitation of the aqueous solution of iron salt and tetramethylammonium hydroxide solution the stable iron ferrite nanoparticles were formulated. These nanoparticles were found to have uniform sizes of about 7 nm, and also showed no coalescence in the aqueous solution for a few months. The superparamagnetic behavior of these nanoparticles was checked by a vibrating sample magnetometer. Also, the temperature dependence of saturation magnetization of nanoparticles was observed using a superconducting quantum interface device magnetometer. The relaxation times of T₁ and T₂ of hydrogen proton in the colloidal aqueous solution of magnetic nanoparticles were measured using a nuclear magnetic resonance spectrometer for the wide range of concentration of nanoparticles in the aqueous solution. The inverse of relaxation times was observed to be directly dependent on the concentration of nanoparticles.     

HgTe/CdS/ZnS多壳层量子点的制备与表征

采用一种简单的方法合成HgTe/CdS/ZnS多壳层量子点。首先,以1-硫代甘油为稳定剂,在水相溶液中制备出HgTe核量子点;然后,采用外延生长法依次在HgTe核量子点表面包覆CdS和ZnS壳层,合成出最终具有稳定近红外发光的HgTe/CdS/ZnS多壳层量子点。该合成方法仅需3个步骤,具有操作简单、成本低廉的优点。实验结果显示,当反应温度为90 ℃、反应溶液pH为11.0、反应加热回流时间为4 min时,HgTe/CdS/ZnS多壳层量子点具有最高荧光量子产率36%。     

Formation of zinc sulfide nanoparticles in HMTA matrix

A hydrothermal method has been optimized for the synthesis of ZnS nanoparticles. The nanoparticles were stabilized using Hexamethylenetetramine (HMTA) as surfactant in aqueous solution. The self-assembling of the surfactant molecules in the water solution forms a unique architecture that can be adopted as the reaction template for the formation of nanomaterials. The average grain size of the nanoparticles calculated from the XRD pattern was of the order of 2 nm which exhibits cubic zinc-blende structure. TEM results showed that the synthesized nanoparticles were uniformly dispersed in the HMTA matrix without aggregation. The spectroscopic results revealed that the synthesized ZnS nanoparticles exhibits strong quantum confinement effect as the optical band gap energy increased significantly compared to the bulk ZnS material. Formation of HMTA capped ZnS nanoparticles were confirmed by FTIR studies. The PL spectra exhibit a strong green emission peak around 502 nm attributed to some self-activated defect centers related to Zn-vacancies.