Temperature dependence of excitonic luminescence from nanocrystalline ZnO films

The properties of the excitonic luminescence for nanocrystalline ZnO thin films are investigated by using the dependence of excitonic photoluminescence (PL) spectra on temperature. The ZnO thin films are prepared by thermal oxidation of ZnS films prepared by low-pressure metalorganic chemical vapor deposition (LP-MOCVD) technique. The X-ray diffraction (XRD) indicates that ZnO thin films have a polycrystalline hexagonal wurtzite structure with a preferred (0 0 2) orientation. A strong ultraviolet (UV) emission peak at 3.26 eV is observed, while the deep-level emission band is barely observable at room temperature. The strength of the exciton-longitudinal-optical (LO) phonon coupling is deduced from the temperature dependence of the full-width at half-maximum (FWHM) of the fundamental excitonic peak, decrease in exciton-longitudinal-optical (LO) phonon coupling strength is due to the quantum confinement effect.     

Properties of sol-gel dip-coated zinc oxide thin films

Zinc oxide (ZnO) films were deposited on glass substrates by the sol-gel dip coating method using acrylamide route. The films were characterized by X-ray diffraction studies which indicated wurtzite structure. Optical absorption measurements indicated band gap in the range 3.17-3.32 eV. XPS studies indicated the formation of ZnO. The resistivity of the films were in the range 1000-10,000 ohm cm.     

The effect of heat treatment on the physical properties of sol-gel derived ZnO thin films

Zinc oxide (ZnO) thin films were deposited on microscope glass substrates by sol-gel spin coating method. Zinc acetate (ZnAc) dehydrate was used as the starting salt material source. A homogeneous and stable solution was prepared by dissolving ZnAc in the solution of monoethanolamine (MEA). ZnO thin films were obtained after preheating the spin coated thin films at 250 °C for 5 min after each coating. The films, after the deposition of the eighth layer, were annealed in air at temperatures of 300 °C, 400 °C and 500 °C for 1 h. The effect of thermal annealing in air on the physical properties of the sol-gel derived ZnO thin films are studied. The powder and its thin film were characterized by X-ray diffractometer (XRD) method. XRD analysis revealed that the annealed ZnO thin films consist of single phase ZnO with wurtzite structure (JCPDS 36-1451) and show the c-axis grain orientation. Increasing annealing temperature increased the c-axis orientation and the crystallite size of the film. The annealed films are highly transparent with average transmission exceeding 80% in the visible range (400-700 nm). The measured optical band gap values of the ZnO thin films were between 3.26 eV and 3.28 eV, which were in the range of band gap values of intrinsic ZnO (3.2-3.3 eV). SEM analysis of annealed thin films has shown a completely different surface morphology behavior.     

Deposition and characterization of transparent and conductive sprayed ZnO:B thin films

Highly transparent and conductive Boron doped zinc oxide (ZnO:B) thin films were deposited using chemical spray pyrolysis (CSP) technique on glass substrate. The effect of variation of boron doping concentration in reducing solution on film properties was investigated. Low angle X-ray analysis showed that the films were polycrystalline fitting well with a hexagonal wurtzite structure and have preferred orientation in [002] direction. The films with resistivity 2.54×10⁻³ Ω-cm and optical transmittance >90% were obtained at optimized boron doping concentration. The optical band gap of ZnO:B films was found ∼3.27 eV from the optical transmittance spectra for the as-deposited films. Due to their excellent optical and electrical properties, ZnO:B films are promising contender for their potential use as transparent window layer and electrodes in solar cells.     

Structural, electrical and optical properties of Gd doped and undoped ZnO:Al (ZAO) thin films prepared by RF magnetron sputtering

The influence of the gadolinium doping on the structural features and opto-electrical properties of ZnO:Al (ZAO) films deposited by radio frequency (RF) magnetron sputtering method onto glass substrates was investigated. X-ray analysis showed that the films were polycrystalline fitting well with a hexagonal wurtzite structure and have preferred orientation in [0 0 2] direction. The Gd doped ZAO film with a thickness of 140 nm showed a high visible region transmittance of 90%. The optical band gap was found to be 3.38 eV for pure ZnO film and 3.58 eV for ZAO films while a drop in optical band gap of ZAO film was observed by Gd doping. The lowest resistivities of 8.4 × 10⁻³ and 10.6 × 10⁻³ Ω cm were observed for Gd doped and undoped ZAO films, respectively, which were deposited at room temperature and annealed at 150 °C.     

The crystalline structure,conductivity and optical properties of Co-doped ZnO thin films

Transparent conductive Co-doped ZnO thin films were deposited by ultrasonic spray technique. Conditions of preparation have been optimized to get good quality. A set of cobalt (Co)-doped ZnO (between 0 and 3 wt%) thin films were grown on glass substrate at 350 °C. The thin films were annealed at 500 °C for improvement of the physical properties. Nanocrystalline films with hexagonal wurtzite structure and a strong (0 0 2) preferred orientation were obtained. The maximum value of grain size G = 63.99 nm is attained with undoped ZnO film. The optical transmissions spectra showed that both the undoped and doped ZnO films have transparency within the visible wavelength region. The band gap energy decreased after doping from 3.367 to 3.319 eV when Co concentration increased from 0 to 2 wt% with slight increase of electrical conductivity of the films from 7.71 to 8.33 (Ω cm)⁻¹. The best estimated structure, optical and electrical results are achieved in Co-doped ZnO film with 2 wt%.     

Boron doped ZnO thin films fabricated by RF-magnetron sputtering

By using the radio frequency-magnetron sputtering (RF-MS) method, both pure ZnO and boron doped ZnO (ZnO:B) thin films were deposited on glass substrates at ambient temperature and then annealed at 450 °C for 2 h in air. It is found that both ZnO and ZnO:B thin films have wurtzite structure of ZnO with (0 0 2) preferred orientation and high average optical transmission (≥80%). Compared with the resistivity of 6.3 × 10² Ω cm for ZnO film, both as-deposited and annealed ZnO:B films exhibit much lower resistivity of 9.2 × 10⁻³ Ω cm and 7.5 × 10⁻³ Ω cm, respectively, due to increase in the carrier concentration. Furthermore, the optical band gaps of 3.38 eV and 3.42 eV for as-deposited and annealed ZnO:B films are broader than that of 3.35 eV for ZnO film. The first-principles calculations show that in ZnO:B thin films not only the band gap becomes narrower but also the Fermi level shifts up into the conduction band with respect to the pure ZnO film. These are consistent with their lower resistivities and suggest that in the process of annealing some substituted B in the lattice change into interstitial B because of its smaller ion radius and this transformation widens the optical band gap of ZnO:B thin film.     

高质量纳米ZnO薄膜的光致发光特性研究

报道了利用低压-金属有机物化学气相沉积技术生长纳米ZnS薄膜，然后，将ZnS薄膜在氧气中于800℃温度下进行热氧化制备高质量纳米ZnO薄膜.x射线衍射结果表明，纳米ZnO薄膜具有六角纤锌矿多晶结构.室温下观察到一束强的紫外(3.26 eV) 光致发光和很弱的深能级发射.根据激子峰的半高宽度与温度的关系确定了激子-纵向光学声子（LO）的耦合强度（ГLO）.由于量子限域效应使ГLO减少较多. 关键词： 光致发光 热氧化 激子 纳米ZnO薄膜     

Chemical bath-deposited ZnS thin films: Preparation and characterization

Chemical bath deposition of ZnS thin films from NH₃/SC(NH₂)₂/ZnSO₄ solutions has been studied. The effect of various process parameters on the growth and the film quality are presented. The influence on the growth rate of solution composition and the structural, optical properties of the ZnS thin films deposited by this method have been studied. The XRF analysis confirmed that volume of oxygen of the as-deposited film is very high. The XRD analysis of as-deposited films shows that the films are cubic ZnS structure. The XRD analysis of annealed films shows the annealed films are cubic ZnS and ZnO mixture structure. Those results confirmed that the as-deposited films have amorphous Zn(OH)₂. SEM studies of the ZnS thin films grown on various growth phases show that ZnS film formed in the none-film phase is discontinuous. ZnS film formed in quasi-linear phase shows a compact and a granular structure with the grain size about 100 nm. There are adsorbed particles on films formed in the saturation phase. Transmission measurement shows that an optical transmittance is about 90% when the wavelength over 500 nm. The band gap (E_g) value of the deposited film is about 3.51 eV.     

Temperature dependence of the optical band gap and electrical conductivity of sol-gel derived undoped and Li-doped ZnO films

Undoped and lithium (Li)-doped ZnO films were prepared by sol-gel method using spin coating technique. The effects of Li content on the crystallinity and morphological properties of ZnO films were assessed by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and atomic force microscopy (AFM). XRD patterns of the films showed the hexagonal wurtzite type polycrystalline structure and that the incorporation of lithium leads to substantial changes in the structural characteristics of ZnO films. The SEM and AFM measurements showed that the surface morphology of the films was affected from the lithium incorporation. The wrinkle network was observed on the surface from both SEM and AFM results for undoped ZnO. The wrinkle structure disappeared with increasing Li content. The absorption spectra of the ZnO and 5% Li-doped ZnO (LZO5) films were carried out between 140 and 400 K temperatures. The optical band gap of ZnO and LZO5 films (calculated at various temperatures) showed a linear dependence on the temperature. The absolute zero value optical band gap and the rate of change of the band gap with temperature of the ZnO and LZO5 films were found to be 3.339 and 3.322 eV, and 2.95 × 10⁻⁴ and 1.60 × 10⁻⁴ eV/K, respectively. The transport mechanisms in the ZnO and LZO5 films have been investigated by analyzing of the temperature (80-300 K) dependence of the conductivity. The activation energies of the ZnO film increased with Li content.     

Structural and optical properties of nano-structured tungsten-doped ZnO thin films grown by pulsed laser deposition

Novel highly c-oriented tungsten-doped zinc oxide (WZO) thin films with 1 wt% were grown by pulsed laser deposition (PLD) technique on corning 1737F glass substrate. The effects of laser energy on the structural, morphological as well as optical transmission properties of the films were studied. The films were highly transparent with average transmittance exceeding 87% in the wavelength region lying between 400 and 2500 nm. X-ray diffraction analysis (XRD) results indicated that the WZO films had c-axis preferred orientation with wurtzite structure. Film thickness and the full width at half maximum (FWHM) of the (0 0 2) peaks of the films were found to be dependent on laser fluence. The composition determined through Rutherford backscattering spectroscopy (RBS) appeared to be independent of the laser fluence. By assuming a direct band gap transition, the band gap values of 3.36, 3.34 and 3.31 eV were obtained for corresponding laser fluence of 1, 1.7 and 2.7 J cm⁻², respectively. Compared with the reported undoped ZnO band gap value of 3.37 eV, it is conjectured that the observed low band gap values obtained in this study may be attributable to tungsten incorporation in the films as well as the increase in laser fluence. The high transparency makes the films useful as optical windows while the high band gap values support the idea that the films could be good candidates for optoelectronic applications.     

Photoluminescence and Raman scattering of Cu-doped ZnO films prepared by magnetron sputtering

The Cu-doped ZnO films were prepared by direct current reactive magnetron sputtering using a zinc target with various Cu-chips attached. The influences of Cu-doping on the microstructure, photoluminescence, and Raman scattering of ZnO films were systematically investigated. The results indicate that ZnO films doped with moderate Cu dopant (2.0-4.4 at.%) can obtain wurtzite structure with strong c-axis orientation. The near band edge (NBE) emission of ZnO film can be enhanced by Cu dopant with a concentration of 2.0 at.% and quench quickly with further increase of doping concentration. Two additional modes at about 230 and 575 cm⁻¹, which could be induced by Cu dopant, can be observed in Raman spectra of the Cu-doped ZnO films.     

Ion-induced secondary electron emission from ZnS thin films deposited by closed-spaced sublimation

ZnS thin films were deposited on soda lime glass and aluminum substrates by close-spaced sublimation technique. The change in composition, structural and optical properties of the films was investigated as a function of the substrate temperature. The deposited films were stoichiometric and crystalline in nature having cubic structure oriented only along (1 1 1) plane. The energy band gap of the films deposited at the substrate temperature of 150, 250 and 350 °C was 3.52, 3.58 and 3.63 eV respectively. These films were then bombarded with 2-10 keV energy pulsed Ar⁺ beam and their electron yield was determined from impinging ion and emitted electron currents. The electron yield of ZnS films was much high as compared to the metals. The electron yield of ZnS films increased with energy of the incident ion and got saturated at about 8 keV. The most important result of this study was that the electron yield of ZnS films having same composition was different. Monte Carlo simulations performed to interpret these experimental findings showed that the dissimilar electron yields of ZnS films is due to the combined effect of energy band gap, surface barrier potential and density of the films.     

The influence of using different substrates on the structural and optical characteristics of ZnO thin films

ZnO thin films with thikness d = 100 nm were deposited onto different substrates such as glass, kapton, and silicon by radio frequency magnetron sputtering. The structural analyses of the films indicate they are polycrystalline and have a wurtzite (hexagonal) structure.The ZnO layer deposited on kapton substrate shows a stronger orientation of the crystallites with (0 0 2) plane parallel to the substrate surface, as compared with the other two samples of ZnO deposited on glass and silicon, respectively.All three layers have nanometer-scale values for roughness, namely 1.7 nm for ZnO/glass, 2.4 nm for ZnO/silicon, and 6.8 nm for ZnO/kapton. The higher value for the ZnO layer deposited on kapton substrate makes this sample suitable for solar cells applications. Transmission spectra of these thin films are strongly influenced by deposition conditions. With our deposition conditions the transparent conducting ZnO layer has a good transmission (78-88%) in VIS and NIR domains. The values of the energy gap calculated from the absorption spectra are 3.23 eV for ZnO sample deposited onto glass substrate and 3.30 eV for the ZnO sample deposited onto kapton polymer foil substrate. The influence of deposition arrangement and oxidation conditions on the structural, morphological, and optical properties of the ZnO films is discussed in the present paper.     

Structural and optical properties of sputtered ZnO thin films

Zinc oxide (ZnO) and aluminium-doped zinc oxide (ZnO:Al) thin films were prepared by RF diode sputtering at varying deposition conditions. The effects of negative bias voltage and RF power on structural and optical properties were investigated. X-ray diffraction measurements (XRD) confirmed that both un-doped and Al-doped ZnO films are polycrystalline and have hexagonal wurtzite structure. The preferential 〈0 0 1〉 orientation and surface roughness evaluated by AFM measurements showed dependence on applied bias voltage and RF power. The sputtered ZnO and ZnO:Al films had high optical transmittance (>90%) in the wavelength range of 400-800 nm, which was not influenced by bias voltage and RF power. ZnO:Al were conductive and highly transparent. Optical band gap of un-doped and Al-doped ZnO thin films depended on negative bias and RF power and in both cases showed tendency to narrowing.     

A comparative study on structural and optical properties of ZnO and Al-doped ZnO thin films obtained by ultrasonic spray method using different solvents

Transparent conducting ZnO and Al doped ZnO thin films were deposited on glass substrate by ultrasonic spray method. The thin films with concentration of 0.1 M were deposited at 350 °C with 2 min of deposition time. The effects of ethanol and methanol solution before and after doping on the structural, optical and electrical properties were examined. The DRX analyses indicated that ZnO films have nanocrystalline nature and hexagonal wurtzite structure with (1 0 0) and (0 0 2) preferential orientation corresponding to ZnO films resulting from methanol and ethanol solution, respectively. The crystallinity of the thin films improved with methanol solution after doping to (0 0 2) oriented. All films exhibit an average optical transparency about 90%, in the visible range. The band gaps values of ZnO thin films are increased after doping from 3.10 to 3.26 eV and 3.27 to 3.30 eV upon Al doping obtained by ethanol and methanol solution, respectively. The electrical conductivity increase from 7.5 to 15.2 (Ω cm)⁻¹ of undoped to Al doped ZnO thin films prepared by using ethanol solution. However, for the methanol solution; the electrical conductivity of the film is stabilized after doping.     

Effect of thickness on structural, optical and electrical properties of nanostructured ZnO thin films by spray pyrolysis

Transparent conducting zinc oxide thin films were prepared by spray pyrolytic decomposition of zinc acetate onto glass substrates with different thickness. The crystallographic structure of the films was studied by X-ray diffraction (XRD). XRD measurement showed that the films were crystallized in the wurtzite phase type. The grain size, lattice constants and strain in films were calculated. The grain size increases with thickness. The studies on the optical properties show that the direct band gap value increases from 3.15 to 3.24 eV when the thickness varies from 600 to 2350 nm. The temperature dependence of the electrical conductivity during the heat treatment was studied. It was observed that heat treatment improve the electrical conductivity of the ZnO thin films. The conductivity was found to increase with film thickness.     

Structural and optical characteristics of spin-coated ZnO thin films

Zinc oxide (ZnO) thin films were deposited onto glass substrates by spin-coating method, from a precursor solution containing zinc acetate, ethanol and ammonium hydroxide. After deposition, the films were heated at a temperature of 100 °C in order to remove unwanted materials. Finally, the films were annealed at 500 °C for complete oxidation. X-ray diffraction showed that ZnO films were polycrystalline and have a hexagonal (wurtzite) structure. The crystallites are preferentially oriented with (0 0 2) planes parallel to the substrate surface. The films have a high transparency (more than 75%) in the spectral range from 450 nm to 1300 nm. The analysis of absorption spectra shows the direct nature of band-to-band transitions. The optical bandgap energy ranges between 3.15 eV and 3.25 eV.Some correlations between the processing parameters (spinning speed, temperature of post deposition heat treatment) and structure and optical characteristics of the respective thin films were established.     

Synthesis of PS colloidal crystal templates and ordered ZnO porous thin films by dip-drawing method

Polystyrene spheres (PS) were synthesized by an emulsifier-free emulsion polymerization technique and the PS colloidal crystal templates were assembled orderly on clean glass substrates by dip-drawing method from emulsion of PS. Porous ZnO thin films were prepared by filling the ZnO sol into the spaces among the close-packed PS templates and then annealing to remove the PS templates. The effects of ZnO precursor sol concentration and dipping time in sol on the porous structure of the thin films were studied. The results showed an ordered ZnO porous thin film with designed pore size that depended on the sol concentration and PS size could be obtained. And the shrinkage of pore diameter was about 30-43%. X-ray diffraction (XRD) spectra indicated the thin film was wurtzite structure. The transmittance spectrum showed that optical transmittance decreased with the decrease of wavelength, but kept above 80% optical transmittances beyond the wavelength of 550 nm. Optical band gap of the porous ZnO thin film (fired at 500 °C) was 3.22 eV.     

Substrate temperature influence on the properties of nanostructured ZnO transparent ultrathin films grown by PLD

Zinc oxide films of 40 nm thickness have been deposited on glass substrates by pulsed laser deposition using an excimer XeCl laser (308 nm) at different substrate temperatures ranging from room temperature to 650 °C. Surface investigations carried out by using atomic force microscopy have shown a strong influence of temperature on the films surface topography. UV-VIS transmittance measurements have shown that our ZnO films are highly transparent in the visible wavelength region, having an average transmittance of ∼90%. The optical band gap of the films was found to be 3.26 eV, which is lower than the theoretical value of 3.37 eV. Besides the normal absorption edge related to the transition between the valence and the conduction band, an additional absorption band was also recorded in the wavelength region around 364 nm (∼3.4 eV). This additional absorption band may be due to excitonic, impurity, and/or quantum size effects. Photoreduction/oxidation in ozone of the ZnO films lead to larger conductivity changes for higher deposition temperature. In conclusion, the ozone sensing characteristics as well as the optical properties of the ZnO thin films deposited by pulsed laser deposition are strongly influenced by the substrate temperature during growth. The sensitivity of the films towards ozone might be enhanced significantly by the control of the films deposition parameters and surface characteristics.