一种片上变压器为负载的用于0.13 μm CMOS工艺2.4GHz WLAN的接收机射频前端电路

A 2.4 GHz radio frequency receiver front end with an on-chip transformer compliant with IEEE 802.11b/g standards is presented. Based on zero-IF receiver architecture, the front end comprises a variable gain common-source low noise amplifier with an on-chip transformer as its load and a high linear quadrature folded Gilbert mixer. As the load of the LNA, the on-chip transformer is optimized for lowest resistive loss and highest power gain. The whole front end draws 21 mA from 1.2 V supply, and the measured results show a double side band noise figure of 3.75 dB, -31 dBm IIP3 with 44 dB conversion gain at maximum gain setting. Implemented in 0.13 μ m CMOS technology, it occupies a 0.612 mm² die size.     

A 1.0 V differential VCO in 0.13 μm CMOS technology

A differential complementary LC voltage controlled oscillator(VCO) with high Q on-chip inductor is presented.The parallel resonator of the VCO consists of inversion-mode MOS(I-MOS) capacitors and an on-chip inductor.The resonator Q factor is mainly limited by the on-chip inductor.It is optimized by designing a single turn inductor that has a simulated Q factor of about 35 at 6 GHz.The proposed VCO is implemented in the SMIC 0.13μm 1P8M MMRF CMOS process,and the chip area is 1.0×0.8 mm~2.The free-running frequency is from 5.73 to 6.35 GHz.When oscillating at 6.35 GHz,the current consumption is 2.55 mA from a supply voltage of 1.0 V and the measured phase noise at 1 MHz offset is -120.14 dBc/Hz.The figure of merit of the proposed VCO is -192.13 dBc/Hz.     

A 0.13μm CMOS Δ ∑ fractional-N frequency synthesizer for WLAN transceivers

A fractional-N frequency synthesizer fabricated in a 0.13μm CMOS technology is presented for the application of IEEE 802.11 b/g wireless local area network(WLAN) transceivers.A monolithic LC voltage controlled oscillator(VCO) is implemented with an on-chip symmetric inductor.The fractional-TV frequency divider consists of a pulse swallow frequency divider and a 3rd-order multistage noise shaping(MASH)△Σmodulator with noise-shaped dithering techniques.Measurement results show that in all channels,phase noise of the synthesizer achieves -93 dBc/Hz and -118 dBc/Hz in band and out of band respectively with a phase-frequency detector (PFD) frequency of 20 MHz and a loop bandwidth of 100 kHz.The integrated RMS phase error is no more than 0.8°.The proposed synthesizer consumes 8.4 mW from a 1.2 V supply and occupies an area of 0.86 mm~2.     

A 4224 MHz low jitter phase-locked loop in 0.13-μm CMOS technology

A 4224 MHz phase-locked loop(PLL) is implemented in 0.13μm CMOS technology.A dynamic phase frequency detector is employed to shorten the delay reset time so as to minimize the noise introduced by the charge pump.Dynamic mismatch of charge pump is considered.By balancing the switch signals of the charge pump,a good dynamic matching characteristic is achieved.A high-speed digital frequency divider with balanced input load is also designed to improve in-band phase noise performance.The 4224 MHz PLL achieves...     

A DESIGN OF 0.25μm CMOS SWITCH

Single-Pole Double-Throw （SPDT） broadband switch has been designed in a 0.25gm Complementary Metal Oxide Semiconductor （CMOS） process. To optimize the performance of isolation and insertion loss, based on normal design, the effects of Gate Series Resistances （GSR） on insertion loss and switching time are analyzed for the first time. The compatible GSRs are chosen by the analyses. The fabricated chips were tested and the results show the switch isolation from DC （Direct Current） to 1GHz exhibits 55dB and insertion loss lower than 2.1 dB.     

2.4GHz 0.35μm CMOS Gilbert下变频器

利用0 35μm CMOS工艺实现了一种用于低中频接收机的Gilbert型下变频器.其中,混频器的输出级采用折叠级联输出,射频信号、本振信号和中频信号的频率分别为2 452GHz,2 45GHz和2MHz.测试表明:在3 3V电源电压条件下,整个混频器电路消耗的电流约为4mA,转换增益超过6dB,输入1dB压缩点约为-11dBm.     

A 0.18μm CMOS single-inductor single-stage quadrature frontend for GNSS receiver

This paper presents an improved merged architecture for a low-IF GNSS receiver frontend,where the bias current and functions are reused in a stacked quadrature LNA-mixer-VCO.Only a single spiral inductor is implemented for the LC resonator and an extra 1/2 frequency divider is added as the quadrature LO signal generator. The details of the design are presented.The gain plan and noise figure are discussed.The phase noise,quadrature accuracy and power consumption are improved.The test chip is fabricated though a 0.18μm RF CMOS process. The measured noise figure is 5.4 dB on average,with a gain of 43 dB and a IIP3 of-39 dBm.The measured phase noise is better than -105 dBc/Hz at 1 MHz offset.The total power consumption is 19.8 mW with a 1.8 V supply. The experimental results satisfy the requirements for GNSS applications.     

0.18μm CMOS工艺5 GHz WLAN功率放大器设计

介绍采用TSMC公司的0.18μm CMOS工艺应用于5 GHzWLAN(无线局域网)发射集中的功率放大器的设计方法,并给出了仿真结果。电路采用A类三级放大结构,在3.3 V工作电压下,增益为23.7 dB,1 dB压缩点输出功率21.8 dBm,最大功率附加效率15%,可望用于WLAN 802.11a标准的系统中。     

A 2.4GHz CMOS Monolithic Transceiver Front-End for IEEE 802.11b Wireless LAN Applications

A 2.4GHz CMOS monolithic transceiver front-end for IEEE 802.11b wireless LAN applications is presented.The receiver and transmitter are both of superheterodyne structure for good system performance.The front-end consists of five blocks:low noise amplifier,down-converter,up-converter, pre-amplifier,and LO buffer.Their input/output impedance are all on-chip matched to 50Ω except the down-converter which has open-drain outputs.The transceiver RF front-end has been implemented in a 0.18μm CMOS process.When the LNA and the down-converter are directly connected,the measured noise figure is 5.2dB,the measured available power gain 12.5dB,the input 1dB compression point -18dBm,and the third-order input intercept point -7dBm.The receiver front-end draws 13.6mA currents from the 1.8V power supply.When the up-converter and pre-amplifier are directly connected,the measured noise figure is 12.4dB,the power gain is 23.8dB,the output 1dB compression point is 15dBm,and the third-order output intercept point is 16dBm.The transmitter consumes 276mA current from the 1.8V power supply.     

A RF receiver frontend for SC-UWB in a 0.18-μm CMOS process

正A radio frequency(RF) receiver frontend for single-carrier ultra-wideband(SC-UWB) is presented. The front end employs direct-conversion architecture,and consists of a differential low noise amplifier(LNA),a quadrature mixer,and two intermediate frequency(IF) amplifiers.The proposed LNA employs source inductively degenerated topology.First,the expression of input impedance matching bandwidth in terms of gate-source capacitance, resonant frequency and target S_(11) is given.Then,a noise figure optimization strategy under gain and power constraints is proposed,with consideration of the integrated gate inductor,the bond-wire inductance,and its variation.The LNA utilizes two stages with different resonant frequencies to acquire flat gain over the 7.1-8.1 GHz frequency band,and has two gain modes to obtain a higher receiver dynamic range.The mixer uses a double balanced Gilbert structure.The front end is fabricated in a TSMC 0.18-/im RF CMOS process and occupies an area of 1.43 mm~2.In high and low gain modes,the measured maximum conversion gain are 42 dB and 22 dB,input 1 dB compression points are -40 dBm and -20 dBm,and S_(11) is better than -18 dB and -14.5 dB.The 3 dB IF bandwidth is more than 500 MHz.The double sideband noise figure is 4.7 dB in high gain mode.The total power consumption is 65 mW from a 1.8 V supply.     

一种2.4GHz 0.35μm CMOS Gilbert下变频器

利用0.35μm CMOS工艺实现了一种用于低中频接收机的Gilbert型下变频器．其中,混频器的输出级采用折叠级联输出,射频信号、本振信号和中频信号的频率分别为2.452GHz,2.45GHz和2MHz．测试表明：在3.3V电源电压条件下,整个混频器电路消耗的电流约为4mA,转换增益超过6dB,输入1dB压缩点约为－11dBm．     

1GHz 0.5μm CMOS低噪声放大器的设计

从低噪声放大器(L NA)的设计原理出发,提出并设计了一种工作于1GHz的实用L NA.电路采用共源-共栅的单端结构,用HSPICE软件对电路进行分析和优化.模拟过程中选用的器件采用TSMC0 .5 μm CMOS工艺实现.模拟结果表明所设计的L NA功耗小于15 m W,增益大于10 d B,噪声系数为1.87d B,IIP3大于10 d Bm,输入反射小于- 5 0 d B.可用于1GHz频段无线接收机的前端     

一种2.4GHz 0.35μm CMOS Gilbert下变频器

利用0.35μm CMOS工艺实现了一种用于低中频接收机的Gilbert型下变频器.其中,混频器的输出级采用折叠级联输出,射频信号、本振信号和中频信号的频率分别为2.452GHz,2.45GHz和2MHz.测试表明:在3.3V电源电压条件下,整个混频器电路消耗的电流约为4mA,转换增益超过6dB,输入1dB压缩点约为-11dBm.     

1GHz 0.5μm CMOS低噪声放大器的设计

从低噪声放大器(LNA)的设计原理出发,提出并设计了一种工作于1GHz的实用LNA.电路采用共源-共栅的单端结构,用HSPICE软件对电路进行分析和优化.模拟过程中选用的器件采用TSMC 0.5μm CMOS工艺实现.模拟结果表明所设计的LNA功耗小于15mW,增益大于10dB,噪声系数为1.87dB,IIP3大于10dBm,输入反射小于-50dB.可用于1GHz频段无线接收机的前端.     

低功耗2.4GHz 0.18μm CMOS全集成低噪声放大器设计

我们利用0.18μm CM O S工艺设计了低噪声放大器。所有电感采用片上螺旋电感,全集成在单个芯片上,并实现片内50Ω匹配。本次电路设计分析采用ADS仿真软件,电源电压1V,工作电流8mA,增益为15.4dB,噪声系数2.7dB,线性度指标IIP 3为-0.6dB。结论是CM O S工艺在工艺和模型方面的改进,使得CM O S RF电路设计更为精确,可集成度更高。     

A fully integrated direct-conversion digital satellite tuner in 0.18μm CMOS

A fully integrated direct-conversion digital satellite tuner for DVB-S/S2 and ABS-S applications is presented.A broadband noise-canceling Balun-LNA and passive quadrature mixers provided a high-linearity low noise RF front-end,while the synthesizer integrated the loop filter to reduce the solution cost and system debug time.Fabricated in 0.18μm CMOS,the chip achieves a less than 7.6 dB noise figure over a 900-2150 MHz L-band, while the measured sensitivity for 4.42 MS/s QPSK-3/4 mode is -91 dBm at the PCB connector.The fully integrated integer-N synthesizer operating from 2150 to 4350 MHz achieves less than 1℃integrated phase error. The chip consumes about 145 mA at a 3.3 V supply with internal integrated LDOs.     

A 0.13μm CMOS △∑ fractional-N frequency synthesizer for WLAN transceivers

A fractional-N frequency synthesizer fabricated in a 0.13 μm CMOS technology is presented for the application of IEEE 802.11 b/g wireless local area network (WLAN) transceivers.A monolithic LC voltage controlled oscillator (VCO) is implemented with an on-chip symmetric inductor.The fractional-N frequency divider consists of a pulse swallow frequency divider and a 3rd-order multistage noise shaping (MASH) △ ∑ modulator with noise-shaped dithering techniques.Measurement results show that in all channels,phase noise of the synthesizer achieves -93 dBc/Hz and -118 dBc/Hz in band and out of band respectively with a phase-frequency detector (PFD) frequency of 20 MHz and a loop bandwidth of 100 kHz.The integrated RMS phase error is no more than 0.8°.The proposed synthesizer consumes 8.4 mW from a 1.2 V supply and occupies an area of 0.86 mm2.     

A 5-GHz programmable frequency divider in 0.18-μm CMOS technology

正A 5-GHz CMOS programmable frequency divider whose modulus can be varied from 2403 to 2480 for 2.4-GHz ZigBee applications is presented.The divider based on a dual-modulus prescaler(DMP) and pulse-swallow counter is designed to reduce power consumption and chip area.Implemented in the 0.18-μm mixed-signal CMOS process,the divider operates over a wide range of 1-7.4 GHz with an input signal of 7.5 dBm;the programmable divider output phase noise is -125.3 dBc/Hz at an offset of 100 kHz.The core circuit without test buffer consumes 4.3 mA current from a 1.8 V power supply and occupies a chip area of approximately 0.015 mm~2.The experimental results indicate that the programmable divider works well for its application in frequency synthesizers.     

A low spur,low jitter 10-GHz phase-locked loop in 0.13-μm CMOS technology

This paper presents a 10-GHz low spur and low jitter phase-locked loop(PLL).An improved low phase noise VCO and a dynamic phase frequency detector with a short delay reset time are employed to reduce the noise of the PLL.We also discuss the methodology to optimize the high frequency prescaler's noise and the charge pump's current mismatch.The chip was fabricated in a SMIC 0.13-μm RF CMOS process with a 1.2-V power supply.The measured integrated RMS jitter is 757 fs(1 kHz to 10 MHz);the phase noise is-89 ...