Studies on Lifted Jet Flames in Coflow: The Stabilization Mechanism in the Near- and Far-Fields

This paper presents the results of a parametric study concerning the phenomenon of liftoff of a nonpremixed jet flame. The dependence of liftoff height on jet exit velocity and coflow velocity is described. It is shown that lifted flames become less sensitive to jet exit velocity as the stabilization point recedes from the burner exit. The results reveal that in cases of extreme liftoff height, increases in jet exit velocity with a constant coflow cause some ethylene flames to stabilize closer to the burner. The success of current theories on lifted flame stabilization in comparison to the experimental results of this study are assessed. The existence of multiple regimes for flame stabilization, incorporating aspects of both premixed and nonpremixed combustion, is proposed.     

Effect of the coflow stream on a plane wall jet

We propose in this work to study an isothermal and a non-isothermal laminar plane wall jet emerging in a coflow steam. The numerical solution of the governing equations was performed by a finite difference method. In this work, we are interested in the study of the influence of Grashof numbers on the wall jet emerging in a medium at rest. Further, we will examine the effect of the coflow stream on the behavior of the dynamic and thermal properties of the wall jet subjected to a constant temperature. A comparison with a simple wall jet is carried out. The results show that for a buoyant wall jet, two parameters can influence the flow: the inertial and buoyancy forces. The velocity effect indicates that the potential core length increases with the velocity ratio. We are also showed that when using a momentum length scale, the normalized longitudinal maximum velocity can reach an asymptotic curve at different velocity ratios.     

The entrainment behavior of a turbulent axisymmetric jet in a viscous host fluid

Although turbulent jets have been studied extensively, one configuration that has not received much attention is the viscosity-stratified jet, wherein a turbulent jet of lower viscosity issues into a density-matched host liquid of higher viscosity. We present experimental data for scalar dispersion and two-dimensional velocity measurements in the axial plane of a turbulent axisymmetric jet with a Reynolds number (Re) of 2,000 issuing into a viscous host liquid at viscosity ratios (m) ranging from 1 to 55. The presence of a strong viscosity discontinuity across the jet edge results in a significant decrease in the scalar spread rate. We attribute this to the rapid reduction in turbulence intensity and the suppression of large engulfing eddies at the jet edge. The velocity profile, on the other hand, indicates that the velocity width and mass flux reduce with increasing m up to about 20, but then increase for higher values of m. This non-monotonic variation is explained by the growing influence of viscous stress for m>20. The scalar spread rate, the velocity spread rate, the centerline velocity decay rate, and the jet mass flux are all minimized for m20 for Re=2,000.

---

Stimulation de l'élargissement d'un jet plan par contrôle fluidique alternéAlternate fluid control for stimulating plane-jet expansion

The present experimental study reports on the efficiency of an alternate use of two actuators placed on either side of a plane jet, to increase lateral jet expansion and to enhance mixing. The investigation is carried out using particle image velocimetry (PIV). Compared to a continuous sinusoidal excitation on both sides of the plane jet, the jet widens considerably when the actuators are switched on alternately with a well chosen timing. An increase of the widening by a factor of two is achieved. The iso-intensity contours of the fluctuating velocity indicate that the high-fluctuation zone greatly spreads out. To cite this article: M. Ben Chiekh et al., C. R. Mecanique 331 (2003).     

Analysis and reconstruction of a pulsed jet in crossflow by multi-plane snapshot POD

In this work, snapshot proper orthogonal decomposition (POD) is used to study a pulsed jet in crossflow where the velocity fields are extracted from stereoscopic particle image velocimetry (SPIV) results. The studied pulsed jet is characterized by a frequency f = 1 Hz, a Reynolds number Re _j  = 500 (based on the mean jet velocity ${\overline{U}_{j}}$  = 1.67 cm/s and a mean velocity ratio of R = 1). Pulsed jet and continuous jet are compared via mean velocity field trajectory and Q criterion. POD results of instantaneous, phase-averaged and fluctuating velocity fields are presented and compared in this paper. Snapshot POD applied on one plane allows us to distinguish an organization of the first spatial eigenmodes. A distinction between “natural modes” and “pulsed modes” is achieved with the results obtained by the pulsed and unforced jet. Secondly, the correlation tensor is established with four parallel planes (multi-plane snapshot POD) for the evaluation of volume spatial modes. These resulting modes are interpolated and the volume velocity field is reconstructed with a minimal number of modes for all the times of the pulsation period. These reconstructions are compared to orthogonal measurements to the transverse jet in order to validate the obtained three-dimensional velocity fields. Finally, this POD approach for the 3D flow field reconstruction from experimental data issued from planes parallel to the flow seems capable to extract relevant information from a complex three-dimensional flow and can be an alternative to tomo-PIV for large volume of measurement.     

Study of parameters and entrainment of a jet in cross-flow arrangement with transition at two low Reynolds numbers

Investigation of the mixing process is one of the main issues in chemical engineering and combustion and the configuration of a jet into a cross-flow (JCF) is often employed for this purpose. Experimental data are gained for the symmetry plane in a JCF-arrangement of an air flow using a combination of particle image velocimetry (PIV) with laser-induced fluorescence (LIF). The experimental data with thoroughly measured boundary conditions are complemented with direct numerical simulations, which are based on idealized boundary conditions. Two similar cases are studied with a fixed jet-to-cross-flow velocity ratio of 3.5 and variable cross-flow Reynolds numbers equal to 4,120 and 8,240; in both cases the jet issues from the pipe at laminar conditions. This leads to a laminar-to-turbulent transition, which depends on the Reynolds number and occurs quicker for the case with higher Reynolds number in both experiments and simulations as well. It was found that the Reynolds number only slightly affects the jet trajectory, which in the case with the higher Reynolds number is slightly deeper. It is attributed to the changed boundary layer shape of the cross-flow. Leeward streamlines bend toward the jet and are responsible for the strong entrainment of cross-flow fluid into the jet. Velocity components are compared for the two Reynolds numbers at the leeward side at positions where strongest entrainment is present and a pressure minimum near the jet trajectory is found. The numerical simulations showed that entrainment is higher for the case with the higher Reynolds number. The latter is attributed to the earlier transition in this case. Fluid entrainment of the jet in cross-flow is more than twice stronger than for a similar flow of a jet issuing into a co-flowing stream. This comparison is made along the trajectory of the two jets at a distance of 5.5 jet diameters downstream and is based on the results from the direct numerical simulations and recently published experiments of a straight jet into a co-flow. Mixing is further studied by means of second-order statistics of the passive scalar variance and the Reynolds fluxes. Windward and leeward sides of the jet exhibit different signs for the time-averaged streamwise Reynolds flux 〈v _x ′c′〉. The large coherent structures which contribute to this effect are investigated by means of timely correlated instantaneous PIV-LIF camera snapshots and their contribution to the average statistics of 〈v _x ′c′〉 are discussed. The discussion on mixing capabilities of the jet in cross-flow is supported by simulation results showing the instantaneous three-dimensional coherent structures defined in terms of the pressure fluctuations.     

Noise reduction of a Mach 0.7–0.9 jet by impinging microjetsRéduction du bruit d'un jet de Mach 0,7–0,9 par un système de microjets impactants

A global noise reduction of a high-subsonic jet is achieved by experimental use of an impinging microjets system. The microjet velocity relative to the main jet velocity, the longitudinal distance of injection and the number of microjets are the three parameters examined in order to obtain the maximum noise reduction. This optimized microjet configuration is obtained by a balance between low-frequency attenuation and high-frequency noise generation due to the interaction between the microjets and the main jet mixing layer. To cite this article: T. Castelain et al., C. R. Mecanique 334 (2006).     

Numerical Simulation of Delft-Jet-in-Hot-Coflow (DJHC) Flames Using the Eddy Dissipation Concept Model for Turbulence–Chemistry Interaction

In this paper, we report results of a numerical investigation of turbulent natural gas combustion for a jet in a coflow of lean combustion products in the Delft-Jet-in-Hot-Coflow (DJHC) burner which emulates MILD (Moderate and Intense Low Oxygen Dilution) combustion behavior. The focus is on assessing the performance of the Eddy Dissipation Concept (EDC) model in combination with two-equation turbulence models and chemical kinetic schemes for about 20 species (Correa mechanism and DRM19 mechanism) by comparing predictions with experimental measurements. We study two different flame conditions corresponding to two different oxygen levels (7.6% and 10.9% by mass) in the hot coflow, and for two jet Reynolds number (Re = 4,100 and Re = 8,800). The mean velocity and turbulent kinetic energy predicted by different turbulence models are in good agreement with data without exhibiting large differences among the model predictions. The realizable k-ε model exhibits better performance in the prediction of entrainment. The EDC combustion model predicts too early ignition leading to a peak in the radial mean temperature profile at too low axial distance. However the model correctly predicts the experimentally observed decreasing trend of lift-off height with jet Reynolds number. A detailed analysis of the mean reaction rate of the EDC model is made and as possible cause for the deviations between model predictions and experiments a low turbulent Reynolds number effect is identified. Using modified EDC model constants prediction of too early ignition can be avoided. The results are weakly sensitive to the sub-model for laminar viscosity and laminar diffusion fluxes.     

Analysis of a turbulent buoyant confined jet modeled using realizable k–ɛ model

Through this paper, analyses of components of the unheated/heated turbulent confined jet are introduced and some models to describe them are developed. Turbulence realizable k–? model is used to model the turbulence of this problem. Numerical simulations of 2D axisymmetric vertical hot water confined jet into a cylindrical tank have been done. Solutions are obtained for unsteady flow while velocity, pressure, temperature and turbulence distributions inside the water tank are analyzed. For seeking verification, an experiment was conducted for measuring of the temperature of the same system, and comparison between the measured and simulated temperature shows a good agreement. Using the simulated results, some models are developed to describe axial velocity, centerline velocity, radial velocity, dynamic pressure, mass flux, momentum flux and buoyancy flux for both unheated (non-buoyant) and heated (buoyant) jet. Finally, the dynamics of the heated jet in terms of the plume function which is a universal quantity and the source parameter are studied and therefore the maximum velocity can be predicted theoretically.     

Time-resolved velocity and concentration measurements in variable-viscosity turbulent jet flow

This paper addresses the ability to reliably measure the fluctuating velocity field in variable-viscosity flows (herein, a propane–air mixture), using hot-wire anemometry. Because the latter is sensitive to both velocity and concentration fluctuations, the instantaneous concentration field also needs to be inferred experimentally. To overcome this difficulty, we show that the hot-wire response becomes insensitive to the concentration of the field, when a small amount of neon is added to the air. In this way, velocity measurements can be made independently of the concentration field. Although not necessary to velocity measurements, Rayleigh light-scattering technique is also used to infer the local (fluctuating) concentration, and, therefore, the viscosity of the fluid. Velocity and concentration measurements are performed in a turbulent propane jet discharging into an air–neon co-flow, for which the density and viscosity ratios are 1.52 and 1/5.5, respectively. The Reynolds number (based on injection diameter and velocity) is 15400. These measurements are first validated: the axial decay of the mean velocity and concentration, as well as the lateral mean and RMS profiles of velocity and concentration, is in full agreement with the existing literature. The variable-viscosity flow along the axis of the round jet is then characterized and compared with a turbulent air jet discharging into still air, for which the Reynolds number (based on injection diameter and velocity) is 5400. Both flows have the same initial jet momentum. As mixing with the viscous co-flow is enhanced with increasing downstream position, the viscosity of the fluid increases rapidly for the case of the propane jet. In comparison with the air jet, the propane jet exhibits: (1) a lower local Reynolds number based on the Taylor microscale (by a factor of four); (2) a reduced range of scales present in the flow; (3) the isotropic form of the mean energy dissipation rate is first more enhanced and then drastically diminishes and (4) a progressively increasing local Schmidt number (from 1.36 to 7.5) for increasing downstream positions. Therefore, the scalar spectra exhibit an increasingly prominent Batchelor regime with a ~ k ^?1 scaling law. The experimental technique developed herein provides a reliable method for the study of variable-viscosity flows.     

Near field vorticity distributions from a sharp-edged rectangular jet

Experimental results on the near field development of a free rectangular jet with aspect ratio 10 are presented. The jet issues from a sharp-edged orifice attached to a rectangular settling chamber at Re_h ∼ 23,000, based on slot width, h. Measurements on cross plane grids were obtained with a two-component hot wire anemometry probe, which provided information on the three dimensional characteristics of the flow field. Two key features of this type of jet are mean axial velocity profiles presenting two off axis peaks, commonly mentioned as saddleback profiles, and a predominant dumbbell shape as described by, for example, a contour of the axial mean velocity. The saddleback shape is found to be significantly influenced by the vorticity distribution in the transverse plane of the jet, while the dumbbell is traced to two terms in the axial mean vorticity transport equation that diffuse fluid from the centre of the jet towards its periphery. At the farthest location where measurements were taken, 30 slot widths from the jet exit, the flow field resembles that of an axisymmetric jet.     

A numerical experiment on the interaction between a film and a turbulent jet

This work is focused on the study of the impingement of a turbulent plane jet on a moving film. A computational fluid dynamics code has been used to simulate the interaction between the turbulent plane jet and the moving film. Since the problem of coupling between turbulence and free surface flow is poorly understood and experiments in this problem are difficult to carry out, this new numerical tool has been designed to give insight into global and local parameters of the free surface flow. To cite this article: D. Lacanette et al., C. R. Mecanique 333 (2005).     

A plane turbulent wall jet on a fully rough surface

The mean velocity field and skin friction characteristics of a plane turbulent wall jet on a smooth and a fully rough surface were studied using Particle Image Velocimetry. The Reynolds number based on the slot height and the exit velocity of the jet was Re = 13,400 and the nominal size of the roughness was k = 0.44 mm. For this Reynolds number and size of roughness element, the flow was in the fully rough regime. The surface roughness results in a distinct change in the shape of the mean velocity profile when scaled in outer coordinates, i.e. using the maximum velocity and outer half-width as the relevant velocity and length scales, respectively. Using inner coordinates, the mean velocity in the lower region of the inner layer was consistent with a logarithmic profile which characterizes the overlap region of a turbulent boundary layer; for the rough wall case, the velocity profile was shifted downward due to the enhanced wall shear stress. For the fully rough flow, the decay rate of the maximum velocity of the wall jet is increased, and the skin friction coefficient is much larger than for the smooth wall case. The inner layer is also thicker for the rough wall case. The effects of surface roughness were observed to penetrate into the outer layer and slightly enhance the spread rate for the outer half-width, which was not observed in most other studies of transitionally rough wall jet flows.     

Velocity and Passive Scalar Characteristics in a Round Jet with Grids at the Nozzle Exit

Velocity and passive scalar (temperature) measurements have been made in the near field of a round jet with and without obstructing grids placed at the jet exit. The Reynolds number Re _D (based on the exit centreline velocity and nozzle diameter) is 4.9 × 10⁴ and the flow is incompressible, while the temperature rise does not affect the velocity behaviour. The streamwise development and radial spreading of the passive scalar are attenuated, relative to the unobstructed jet. Close to the jet outlet, the spatial similarity of the moments (up to the third-order) of velocity fluctuations is improved, when the jet is perturbed. An explanation, based on the reduced effect of the large coherent structures in the developing region, is provided.     

UNSTEADY LIFT AND SOUND PRODUCED BY AN AIRFOIL IN A TURBULENT BOUNDARY LAYER

An analysis is made of the unsteady lift exerted on a stationary rigid body immersed in an incompressible, plane-wall turbulent boundary layer. The lift is expressed as a surface integral over the body involving theupwash velocity induced by the “free” vorticity Ω (found by taking explicit account of the interaction of the body with the flow and excluding the bound vorticity) and a harmonic function X₂that depends only on the shape of the body. The upwash velocity is the free-field velocity given in terms of Ω by the Biot–Savart formula, augmented by the velocity field of a conventional distribution of image vortices in the wall. The function X₂can be interpreted as the velocity potential of flow past the body, produced by motion of the wall at unit speed towards the body. Detailed predictions are made of the lift on a slender airfoil placed in the outer region of the boundary-layer. When the airfoil chord is large compared to the boundary-layer thickness, vortex shedding into the wake causes the magnitude of the net upwash velocity near the trailing edge to be small. The main contributions to the surface integral are then from the nose region, where the upwash velocity may be estimated independently of the fluctuations near the trailing edge. Analytical results for a thin plate airfoil of chord 2a at distance h from the wall show that the lift increases as a/h increases; it is ultimately independent of a and scales with the ratio of h to the hydrodynamic wavelength. Application is made to determine the sound generated by the airfoil in a weakly compressible boundary layer flow over a finite elastic plate.     

Study of active flow control for a simplified vehicle model using the PANS method

Flow control has shown a potential in reducing the drag in vehicle aerodynamics. The present numerical study deals with active flow control for a quasi-2D simplified vehicle model using a synthetic jet (zero net mass flux jet). Recently developed near-wall Partially-Averaged Navier–Stokes (PANS) method, based on the ζ–f RANS turbulence model, is used. The aim is to validate the performance of this new method for the complex flow control problem. Results are compared with previous studies using LES and experiments, including global flow parameters of Strouhal number, drag coefficients and velocity profiles. The PANS method predicts a drag reduction of approximately 15%, which is closer to the experimental data than the previous LES results. The velocity profiles predicted by the PANS method agree well with LES results and experimental data for both natural and controlled cases. The PANS prediction showed that the near-wake region is locked-on due to the synthetic jet, and the shear layer instabilities are thus depressed which resulted in an elongated wake region and reduced drag. It demonstrates that the PANS method is able to predict the flow control problem well and is thus appropriate for flow control studies.     

Vortex ring velocity and minimum separation in an infinite train of vortex rings generated by a fully pulsed jet

A pulsed jet with a period of no flow between pulses (i.e., a fully pulsed jet) produces a multiplicity of vortex rings whose characteristics are determined by the jet pulsing parameters. The present study analyzes the case of impulsively initiated and terminated jet pulses in the limit of equal pulse duration and period to determine the minimum possible vortex ring separation obtainable from a fully pulsed jet. The downstream character of the flow is modeled as an infinite train of thin, coaxial vortex rings. Assuming inviscid flow and matching the circulation, impulse, kinetic energy, and frequency of the jet and vortex ring train allow the properties of the vortex ring train to be determined in terms of the ratio of jet slug length-to-diameter ratio (L/D) used for each pulse. The results show the minimum ring separation may be made arbitrarily small as L/D is decreased and the corresponding total ring velocity remains close to half the jet velocity for L/D < 4, but the thin-ring assumption is violated for L/D > 1.5. The results are discussed in the context of models of pulsed-jet propulsion.     

Determination of complete velocity gradient tensor by using cinematographic stereoscopic PIV in a turbulent jet

Cinematographic stereoscopic PIV measurements were performed in the far field of an axisymmetric co-flowing turbulent round jet (Re _T ≈ 150, where Re _T is the Reynolds number based on Taylor micro scale) to resolve small and intermediate scales of turbulence. The time-resolved three-component PIV measurements were performed in a plane normal to the axis of the jet and the data were converted to quasi-instantaneous three-dimensional (volumetric) data by using Taylor’s hypothesis. The availability of the quasi-three-dimensional data enabled the computation of all nine components of the velocity gradient tensor over a volume. The use of Taylor’s hypothesis was validated by performing a separate set of time-resolved two component “side-view” PIV measurements in a plane along the jet axis. Probability density distributions of the velocity gradients computed using Taylor’s hypothesis show good agreement with those computed directly with the spatially resolved data. The overall spatial structure of the gradients computed directly exhibits excellent similarity with that computed using Taylor’s hypothesis. The accuracy of the velocity gradients computed from the pseudo-volume was assessed by computing the divergence error in the flow field. The root mean square (rms) of the divergence error relative to the magnitude of the velocity gradient tensor was found to be 0.25, which is consistent with results based on other gradient measurement techniques. The velocity gradients, vorticity components and mean dissipation in the self-similar far field of the jet were found to satisfy the axisymmetric isotropy conditions. The divergence error present in the data is attributed to the intrinsic uncertainty associated with performing stereoscopic PIV measurements and not to the use of Taylor’s hypothesis. The divergence error in the data is found to affect areas of low gradient values and manifests as nonphysical values for quantities like the normalized eigenvalues of the strain-rate tensor. However, the high gradients are less affected by the divergence error and so it can be inferred that structural features of regions of intense vorticity and dissipation will be faithfully rendered.     

Numerical Study of Turbulent Jet Ignition in a Lean Premixed Configuration

Direct numerical simulations (DNS) of a hot combustion product jet interacting with a lean premixed hydrogen-air coflow are conducted to fundamentally investigate turbulent jet ignition (TJI) in a three-dimensional configuration. TJI is an efficient method for initiating and controlling combustion in ultra-lean combustion systems. Fully compressible gas dynamics and species equations are solved with high order finite difference methods. The hydrogen-air reaction is simulated with a reliable detailed chemical kinetics mechanism. The physical processes involved in the TJI-assisted combustion are investigated by considering the flame heat release, temperature, species concentrations, vorticity, and Baroclinc torque. The complex turbulent flame and flow structures are delineated in three main: i) hot product jet, ii) burned-mixed, and iii) flame zones. In the TJI-assisted combustion, the flow structures and the flame features such as flame speed, temperature, and species distribution are found to be quite different than those in “standard” turbulent premixed combustion due to the existence of a high energy turbulent hot product jet. The flow structures and statistics are also found to be different than those normally seen in non-isothermal non-reacting jets.