Gas chromatographic-mass spectrometric analysis of diols and tetrols from reactions of polycyclic aromatic hydrocarbon epoxides with hemoglobin

We have evaluated both electron ionization (EI) and negative-ion chemical ionization (NICI) methods for the analysis of trimethylsilyl derivatives of a series of polycyclic aromatic hydrocarbon (PAH) alcohols including styrene diol, benzo[e]pyrene diol and tetrols, cyclopenta[c,d]pyrene diols, benzo[a]pyrene-4,5-diols, chrysene tetrols, benz[a]anthracene tetrols I and II, and syn- and anti-benzo[a]pyrene tetrols. NICI is the more sensitive method for all compounds except styrene diol. Detection limits are compound-dependent and range from 1 fmol for cyclopenta[c,d]pyrene diol to 1 pmol for benzo[e]pyrene diol. The EI detection limit for styrene diol is 60 fmol. PAH alcohols related to the compounds listed above were observed following hydrolysis of hemoglobin which had been reacted with PAH epoxides in vitro. Benzo[a]pyrene tetrols and a chrysene tetrol were observed following hydrolysis of hemoglobin isolated from human smokers' blood. Hydrolysis of styrene oxide treated hemoglobin in 18O-labeled water revealed at least two mechanisms of ester hydrolysis, including the BAL 1 pathway.     

Separation and detection of a benzo[a]pyrene metabolite with capillary electrophoresis in the presence of DNA using laser-induced fluorescence

A novel approach was developed for the separation and detection of a benzo[a]pyrene B[a]P-DNA metabolite (tetrol I-1) in the presence of DNA using CE and laser induced fluorescence. Tetrol I-1 in the presence of DNA is intercalated and undergoes fluorescence quenching. Thus, an equilibrium is established between the intercalated tetrol I-1 and the uncomplexed tetrol I-1. It is only the uncomplexed tetrol that is fluorescent in the presence of DNA. The tetrol I-1 fluorescence intensities, at two concentrations of tetrol I-1 (0.005 and 0.01mg ml(-1)), were observed while varying the DNA concentration. Stern-Volmer plots were constructed of the fluorescence intensity of the uncomplexed tetrol I-1 versus DNA concentration. From the slopes of the Stern-Volmer plots quenching constants were determined. The quenching constants are essentially the same as an association constant for tetrol I-1 with DNA. The average value obtained for the association constant for the two concentrations of tetrol I-1 was 0.22+/-0.02 mg ml(-1). It was thus demonstrated that uncomplexed tetrol I-1 can be separated from DNA by CE and an association constant for tetrol I-1 bound to DNA can be obtained from the fluorescence quenching data.     

Determination of rotenone in river water utilizing packed capillary column switching liquid chromatography with UV and time-of-flight mass spectrometric detection

Fast and sensitive packed capillary column switching liquid chromatography methodology has been developed for the determination of the pesticide rotenone in river water. Sample volumes of up to 1 ml are loaded onto a 23 x 0.25 mm, 5 microm Kromasil C18 packed capillary precolumn using a noneluting solvent composition of water-acetonitrile (99:1, v/v) at flow-rates up to 100 microl/min prior to solute backflushing onto a 200 x 0.32 mm, 3.5 microm Kromasil C18 packed capillary analytical column using a mobile phase of water-acetonitrile (30:70, v/v) at a flow-rate of 5 microl/min. The method was evaluated using river water samples spiked with rotenone in the concentration range 0.5-50 ng/ml using UV detection. The within-assay precision was between 5.0 and 7.7% relative standard deviation (RSD, n = 6) and the between assay precision was between 7.5 and 8.9% RSD (n = 6). The method was linear within the investigated mass range displaying a calibration curve correlation factor of 0.997. The mass limit of detection was 10 pg corresponding to a concentration limit of detection of 10 pg/ml, using time-of-flight mass spectrometry.     

Screening potential of solid-phase extraction and solid surface room temperature fluorimetry for polycyclic aromatic hydrocarbons in water samples

The analytical potential of solid-phase extraction and room temperature fluorimetry for screening polycylic aromatic hydrocarbons in water samples is evaluated. Solid-phase extraction was performed via a syringe procedure previously reported (Talanta 52 (2000) 727). The simplicity of fluorescence measurements on the solid substrate is equivalent to solution measurements. Since oxygen quenching of fluorescence is not significant, placing the extraction membrane in the substrate holder of the spectrometer rapidly performs fluorescence measurements. Limits of detection at the pg ml(-1) level were estimated for several pollutants. With a commercial spectrofluorimeter, benzo(a)pyrene was quantitatively determined at the 5 pg ml(-1) concentration level. This concentration compared favorably to limits of detection estimated by laser-induced fluorimetry. A unique advantage of this approach was the possibility of adjusting the volume of extracted water to reach concentration levels below instrumental detection levels. Since SPE procedure was rapid and simple the trade-off of including an additional experimental step to lower limits of detection was advantageous. Although the selectivity of this approach was not fully investigated, our studies showed that selective excitation was sufficient to identify benzo(a)pyrene in a seven-component mixture and spiked Red River water of unknown composition.     

Separation and characterization of tetrol metabolites of benzo[a]pyrene-DNA adducts using HPLC and solid-matrix room temperature luminescence

Four tetrols of benzo[a]pyrene-DNA adducts were separated using reversed-phase high performance liquid chromatography. Chromatographic fractions containing a given tetrol were readily characterized with solid-matrix room temperature luminescence techniques. Solid-matrix fluorescence and phosphorescence spectra at picogram amounts of a tetrol were easily obtained. Tetrol fractions collected based on retention times, but with no response from the ultraviolet detector, were characterized by solid-matrix luminescence spectra at very small quantities.     

采用新型固相萃取柱快速测定食用植物油中苯并［a］芘

研究了Bond Elut ENV新型固相萃取柱在食用植物油中苯并[a]芘快速检测中的应用,建立了快速测定食用植物油样品中苯并[a]芘残留量的固相萃取/液相色谱/荧光检测法。样品用正己烷溶解,固相萃取净化,SUPELCOSILTMLC-PAH(25 cm×4.6 mm,5μm)色谱柱分离,以乙腈-水(95∶5)为流动相,荧光检测(λex=297 nm,λem=408 nm),外标法定量。苯并[a]芘的检出限为0.3μg/kg,在1.0～50.0μg/L范围内线性关系良好,相关系数为0.999 6,方法的回收率为79%～102%,相对标准偏差不高于9.4%。该方法准确、实用、简便、快速,在食用植物油的苯并[a]芘残留量检测方面有广泛的应用前景。     

Micelle-sensitized constant-energy synchronous fluorescence spectrometry for the simultaneous determination of pyrene, benzo[a]pyrene and perylene.

The use of micellar media in constant-energy synchronous fluorescence spectrometry has been proposed. The influence of some aqueous micellar systems on the determination of pyrene, perylene and benzo[a]pyrene has been investigated. The presence of these micellar systems allows their determination in aqueous media, thus avoiding the use of an organic solvent, and greatly enhances the fluorescence signals. The combination of a constant-energy synchronous scanning technique and a micellar system provided a single spectrum for the simultaneous identification and quantitative determination of the three polycyclic aromatic hydrocarbons (PAHs). Further there was no energy transfer among them, making the measurement simple and fast. A constant-energy difference of 2800 cm(-1) was selected. The analytical characteristics of the proposed method in the presence of anionic micelles of sodium dodecylsulfate (SDS) were studied. The detection limits were at a level of ng ml(-1). Analysis of water samples from two different origins spiked with known amount of pyrene, perylene and benzo[a]pyrene also gave satisfactory results, and total average recoveries were greater than 97.1%.     

Admicelle-enhanced synchronous fluorescence spectrometry for the selective determination of polycyclic aromatic hydrocarbons in water

A simple and rapid method for the highly sensitive determination of polycyclic aromatic hydrocarbons (PAHs) in water was developed. Benzo[a]pyrene, benzo[k]fluoranthene, perylene, and pyrene in water were concentrated into sodium dodecyl sulfate (SDS)-alumina admicelles. The collection was performed by adding SDS and alumina particles into the sample solution at pH 2. After gentle mixing, the resulting suspension was passed through a membrane filter to collect the SDS admicelles containing highly concentrated PAHs. The filter was placed on a slide glass and then covered admicellar layer with a fused silica glass plate before setting in a fluorescence spectrometer. Benzo[a]pyrene, benzo[k]fluoranthene, perylene, and pyrene were selectively determined by the synchronous fluorescence scan (SFS) analysis with keeping wavelength intervals between excitation and emission to 98, 35, 29, and 45 nm, respectively. Because of the minimum spectral overlapping, 1-40 ng l⁻¹ of benzo[a]pyrene, benzo[k]fluoranthene, and perylene as well as 10-150 ng l⁻¹ of pyrene were selectively determined with eliminating the interferences of other 12 PAHs. The detection limits were 0.3 ng l⁻¹ for benzo[a]pyrene, benzo[k]fluoranthene, and perylene, and 1 ng l⁻¹ for pyrene. They were 2-3 orders of magnitude lower than the detection limits in normal aqueous micellar solutions. The application to water analysis was studied.     

On the improvement of solid-phase extraction room-temperature phosphorimetry for the analysis of polycyclic aromatic hydrocarbons in water samples

This article presents considerable improvements in SPE-RTP methodology for the analysis of polycyclic aromatic hydrocarbons in water samples. Bulky glassware and vacuum pump were removed from the previous extraction procedure [E.D. Hagestuen, A.D. Campiglia, Talanta 49 (1998) 547] by processing 10 ml of sample with syringes and stainless steel filter holders. The oven-drying step was substituted by air sample drying, which employed positive pressure to remove water excess from the extraction membrane. As a result, analysis times from 8 to 10 min per sample were obtained. No costs in levels of detection were observed. Limits of detection at the pg ml(-1) level were estimated for phenanthrene, pyrene, benzo(k)fluoranthene, benzo(a)pyrene, and chrysene. The feasibility of identifying single components in PAH mixtures was investigated. Binary and tertiary mixtures were resolved by appropriate choice of excitation and emission wavelengths. The advantage of using excitation-emission matrix analysis was demonstrated for a six-component mixture.     

Mass spectrometric detection in narrow-bore (0.10 mm i.d.) capillary chromatography fast, sensitive and selective analysis of polychlorinated biphenyls

The combination of narrow-bore capillary gas chromatography with bench-top quadrupole mass spectrometric detection was evaluated for the determination of polychlorinated biphenyls (PCBs). The qualitative and quantitative performances of the system are illustrated by several analyses (PCB standards and human milk extracts). Capillary columns with different internal diameters (0.10, 0.18 and 0.22 mm, respectively) were compared for their ability to separate PCB congeners and the analysis time. Short run times (less than 7 min) were sufficient for complete separation of PCB congeners on a 0.10-mm internal diameter (I.D.) capillary column without any loss of resolution when compared with a 0.22 mm I.D. column. Good qualitative and quantitative data acquisition was possible with quadrupole mass spectrometer for run times of 8 min, but incomplete peak reading was observed when run times were reduced to 3-4 min. Selected ion monitoring and dwell times of 10 ms are necessary to obtain detection limits for individual PCB congeners as low as 0.4 pg microl(-1) for standard solutions and 0.2 ng g(-1) fat for milk extracts. By using cold splitless injection, relatively high volumes (1 microl) for narrow-bore capillaries could be injected without any peak distortion.     

Supersonic jet fluorescence spectrometry of perylene and benzo[a]pyrene

A supersonic jet instrument for fluorescence spectrometry is described. It consists of a high-temperature free expansion nozzle for continuous sample introduction and a vacuum chamber equipped with a high-speed pumping system. Rotationally cooled spectra obtained with the supersonic jet are compared with gas-phase spectra measured at high temperature for perylene and benzo[a]pyrene molecules. Each component of the unresolved band structure in the high-temperature spectra was found to be composed of a rotational congestion of several vibrational bands. For a 1:1 mixture of perylene and benzo[a]pyrene, selective detection is possible by using supersonic jet spectrometry. The detection limit for perylene is 100 ng. The advantage of this technique over other low-temperature spectrometric methods based on Shpol'skii and matrix isolation effects are discussed.     

New approach for screening polycyclic aromatic hydrocarbons in water samples

For the first time, solid-phase extraction (SPE) has been combined to room-temperature phosphorimetry (RTP) to determine the 16 polycylic aromatic hydrocarbons related as major pollutants by the US Environmental Protection Agency (EPA). These include naphthalene, anthracene, acenaphthylene, acenaphthene, fluorene, fluoranthene, benzo(a)anthracene, benzo(k)fluoranthene, benzo(b)fluoranthene, benzo(a)pyrene, indeno(1,2,3-cd)pyrene, pyrene, chrysene, phenanthrene, benzo(g,h,i)perylene and dibenzo(a,h)anthracene. The pre-concentration factor obtained by SPE, combined with the sensitivity of RTP, resulted in calibration curves with linear dynamic ranges at the parts-per-billion level (ng ml(-1)). The limits of detection were estimated at the parts-per-trillion level (pg ml(-1)). Several pollutants usually encountered in water samples were tested for interference. These included polychlorinated biphenyls, pesticides, and volatile organic compounds. As a result of the appropriate combination of excitation wavelength (330 nm) and phosphorescence enhancers (0.1 M TlNO(3) and 0.05 M sodium dodecyl sulfate, SDS), no interference was observed. The results demonstrate the potential of SPE-RTP for screening polycyclic aromatic hydrocarbons (PAHs) in environmental waters.     

Fluorescence study of the solubilization of benzo[a]pyrene: application to its detection in coal washing waters

The solubilization of benzo[a]pyrene by organic solvents (dioxane, toluene and dichloromethane) and a surfactant (Triton X-100) was investigated. These media were successfully used for the determination of benzo[a]pyrene using fluorescence detection, with excellent limits of detection and large linear analytical ranges. Benzo[a]pyrene was detected in coal washing waters using liquid chromatography with fluorescence detection. The stability of this compound in dioxane was also examined.     

Laser-induced fluorescence with an OPO system. Part I. Optimisation of the analytical system by use of experimental design methodology. Application to the direct quantification of traces of benzo[<Emphasis Type="Italic">a</Emphasis>]pyrene

This study deals with the optimisation and application of a method for direct analysis of trace pollutants in water by laser-induced fluorescence. The arrangement used consisted of an Nd:YAG Laser coupled with an optical parametric oscillator (LYOPO) and connected to a spectrophotometer and a high-sensitivity camera. Optimisation was achieved by developing an experimental design methodology to maximise the signal-to-noise ratio and reduce the limit of detection. The technique was then applied to the detection of benzo[ a]pyrene in water. The experimental results were evidence of its high sensitivity and time-resolution potential. The detection limit for benzo[ a]pyrene was 0.7 ng L(-1) in drinking water and 4 ng L(-1) in raw water containing 1 mg L(-1) humic acids.     

固相萃取-高效液相色谱-荧光法测定方便面和烤肠中的苯并[a]芘

建立了固相萃取-高效液相色谱-荧光法检测方便面和烤肠中苯并[a]芘的方法。采用正己烷作为提取溶剂,经苯并[a]芘专用固相萃取柱HiCapt Benzo富集净化,高效液相色谱-荧光法对样品中苯并[a]芘进行分离分析。苯并[a]芘的质量浓度在0.5~20.0μg/kg范围内与色谱峰面积呈良好的线性关系,相关系数R2为0.9997。方便面和烤肠中苯并[a]芘的加标回收率分别为92.2%~98.3%和95.9%~97.9%,日内和日间相对标准偏差分别为3.34%~5.01%和2.11%~4.07%。与传统方法相比,该方法快速简单、有机溶剂消耗少,在油炸烟熏食品的苯并[a]芘分析中具有较大应用前景。     

Sensitive and selective determination of metabolically formed trans-dihydrodiols and phenols of benzo[a]pyrene in water and urine samples by HPLC with amperometric detection

A method has been developed to separate hydroxylated metabolites of the carcinogenic polycyclic aromatic hydrocarbon benzo[a]pyrene, i. e. trans-4,5-, 7,8-, 9,10-dihydrodiol and 1-, 3-, 7-, and 9-phenol, by HPLC with amperometric detection employing an isocratic methanol/water eluent (70:30, v/v) containing 0.5 g/L sulfuric acid and 1 g/L lithium perchlorate. Compared with the usually applied fluorescence (λ_ex = 265 nm, λ_em = 460 nm) and ultraviolet (λ = 265 nm) detection, the amperometric technique is about 2–12 times more sensitive for the determination of all metabolites investigated. The method was applied to the determination of the seven metabolites of benzo[a]pyrene in different water samples and in urine after solid-phase extraction (SPE). The results obtained by HPLC with amperometric detection after SPE enrichment from an aqueous extract of a soil sample and from the urine of a rat intragastrically treated with benzo[a]pyrene agreed well with the values determined with fluorescence and/or UV detection.     

Sensitive and selective determination of metabolically formed trans-dihydrodiols and phenols of benzo[a]pyrene in water and urine samples by HPLC with amperometric detection

A method has been developed to separate hydroxylated metabolites of the carcinogenic polycyclic aromatic hydrocarbon benzo[a]pyrene, i. e. trans-4,5-, 7,8-, 9,10-dihydrodiol and 1-, 3-, 7-, and 9-phenol, by HPLC with amperometric detection employing an isocratic methanol/water eluent (70:30, v/v) containing 0.5 g/L sulfuric acid and 1 g/L lithium perchlorate. Compared with the usually applied fluorescence (λ_ex = 265 nm, λ_em = 460 nm) and ultraviolet (λ = 265 nm) detection, the amperometric technique is about 2–12 times more sensitive for the determination of all metabolites investigated. The method was applied to the determination of the seven metabolites of benzo[a]pyrene in different water samples and in urine after solid-phase extraction (SPE). The results obtained by HPLC with amperometric detection after SPE enrichment from an aqueous extract of a soil sample and from the urine of a rat intragastrically treated with benzo[a]pyrene agreed well with the values determined with fluorescence and/or UV detection. Received: 20 December 1996 / Revised: 10 March 1997 / Accepted: 30 April 1997     

High resolution spectral differentiation of enantiomers: benzo[a]pyrene tetrols complexed with a promiscuous antibody

The interaction of the highly cross-reactive anti-PAH monoclonal antibody with four diastereomeric benzo[a]pyrene tetrols (BPTs) is studied by means of fluorescence line-narrowing spectroscopy. It is shown that the interaction of enantiomers of cis-BPT and trans-BPT with the antibody involves different complex geometries. These spatially different ligand-protein interactions alter the relative intensities of the excited-state vibrational frequencies of immunocomplexed molecules allowing for unambiguous spectroscopic resolution of all four enantiomeric isomers. This study represents the first example of a high-resolution, fluorescence-based spectroscopic method capable of enantiospecific differentiation.     

Coupling micelle-mediated extraction using mixtures of surfactants and fluorescence measurements with a fiber-optic for the screening of PAHs in seawater

The screening of PAHs from seawater samples using cloud-point extraction (CPE) as a step prior to their determination by fluorescence measurements with a fiber-optic is proposed. The CPE is carried out with the nonionic surfactants mixture POLE and Brij 30. The fluorescence measurement parameters were optimized, allowing selection of benzo(a)pyrene (B(a)Py) and benzo(k)fluoranthene (B(k)Ft) as the target analytes for the screening. The reproducibility of the whole screening system, expressed as relative standard deviation, was 9.0% for B(a)Py and 12.1% for B(k)Ft (both for n = 7). The reliability of the method was established at five concentrations for B(a)Py (between 0.5 and 3.3 times the detection limit: 0.31 ng ml(-1)) and at three concentrations for B(k)Ft (between 0.6 and 2.5 times the detection limit: 0.56 ng ml(-1)). The resolution of binary mixtures of these PAHs at different levels of concentration, and a study of the interferences with the rest of the PAHs were also carried out.     

Determination of vitamin K1 in emulsified nutritional supplements by solid-phase extraction and high-performance liquid chromatography with postcolumn reduction on a platinum catalyst and fluorescence detection

Determination of small amounts of vitamin K1 (0.8 microg/g) in nutritional supplements with high fat content (20 mg/g) was performed by solid-phase extraction and high-performance liquid chromatography (HPLC) with fluorescence detection after reduction on a platinum oxide catalyst. The concentration ratio of plant oils to vitamin K1 (0.8 microg/g) was about 25,000:1. A sample solution was applied to a solid-phase extraction cartridge and vitamin K1 was eluted with ethanol, followed by HPLC. The proposed method was simple, rapid (analysis time: ca. 12 min), sensitive [detection limit: ca. 0.1 pg per injection (100 microl) at a signal-to-noise ratio of 3:1], highly selective and reproducible [relative standard deviation: ca. 1.3%. (n=5)]. The calibration graph of vitamin K1 was linear in the range of 0-2 pg per injection (100 microl). Recovery of vitamin K1 was over 90% by the standard addition method.