Detection of mid-IR radiation by sum frequency generation for free space optical communication

We present an experiment where mid-infrared radiation is detected indirectly via the second-order non-linear process of sum frequency generation. The mid-infrared sources used for the experiment are quantum cascade lasers, and we use a pump wavelength that yields an up-converted wavelength within the detection window of Silicon avalanche photo diodes. Compared with direct detection using state-of-the-art mid-infrared semiconductor detectors, the detection scheme we propose in this paper has the advantages of greater bandwidth and lower noise equivalent power.     

V型腔腔内和频产生3 W连续波589 nm黄光激光器

报道了双Nd：YAG棒串接V型折叠腔腔内KTP和频全固态黄光激光器，得到了3 W连续波589 nm黄光输出.为了提高黄光输出功率，采用了两种手段：一是通过优化腔型设计使得两束基频在腔内达到了最佳的空间重合，二是通过选择合适大小的二极管激光器的抽运功率使得两束基频在腔内达到了最佳的功率配比. 关键词： 全固态激光器 Nd：YAG激光器 黄光 腔内和频     

Quasi-optical mixer for efficient sum and difference frequency sidebands generation at 1 THz mark

Construction details of recently developed mixer for generation of narrow band and continuously tunable submillimeter radiation are reviewed briefly. The measurements indicate the usability of such mixer design for the high resolution spectroscopical work at frequencies close to and above the 1 THz mark.The work described was performed by the author during his stay within Department of Atomic and Molecular Physics of Katholieke Universiteit, Nymegen, The Netherlands under the guidance of Prof.Dr. A. Dymanus.     

A diode laser spectrometer at 634nm and absolute frequency measurements using optical frequency comb

This paper reports that two identical external-cavity-diode-laser (ECDL) based spectrometers are constructed at 634 nm referencing on the hyperfine B-X transition R(80)8-4 of ¹²⁷I₂. The lasers are stabilized on the Doppler-free absorption signals using the third-harmonic detection technique. The instability of the stabilized laser is measured to be 2.8×10^-12 (after 1000 s) by counting the beat note between the two lasers. The absolute optical frequency of the transition is, for the first time, determined to be 472851936189.5 kHz by using an optical frequency comb referenced on the microwave caesium atomic clock. The uncertainty of the measurement is less than 4.9 kHz.     

Pump-induced carrier envelope offset frequency dynamics and stabilization of an Yb-doped fiber frequency comb

In this paper, we demonstrate a carrier envelope phase-stabilized Yb-doped fiber frequency comb seeding by a nonlinear-polarization-evolution（NPE） mode-locked laser at a repetition rate of 60 MHz with a pulse duration of 191 fs.The pump-induced carrier envelope offset frequency（ f0） nonlinear tuning is discussed and further explained by the spectrum shift of the laser pulse. Through the environmental noise suppression, the drift of the free-running f0 is reduced down to less than 3 MHz within an hour. By feedback control on the pump power with a self-made phase-lock loop（PLL）electronics the carrier envelope offset frequency is well phase-locked with a frequency jitter of 85 m Hz within an hour.     

增益饱和对光学差频产生太赫兹辐射的功率和稳定性的影响

数值模拟并分析了以GaSe晶体为例对光学差频产生太赫兹（THz）波的特性.结果表明：当THz波长为227.5 μm,晶体长度为26.3 mm时,产生THz波功率达到增益饱和,在增益饱和点输出最高峰值功率可以达到945 W.由于晶体吸收的影响,THz波的增益饱和区是输出功率的非稳定区,而THz波的输出稳定区位于增益饱和区之后,在稳定区的THz波稳定性取决于抽运光的稳定性.当THz波波长为227.5 μm时,达到稳定区所需晶体长度为37.9 mm,此时THz波输出峰值功率可以达到735 W. 关键词： 光学差频 太赫兹辐射 稳定性     

飞秒光梳和碘稳频532nm Nd:YAG激光频率的测量

报道了中国计量科学研究院研制的基于掺钛蓝宝石(Ti:Sapphire)锁模飞秒脉冲激光器的飞秒光学频率梳装置，并利用此装置测量了碘稳频532nm(¹²⁷I₂R(56)32-10) Nd∶YAG固体激光器的频率，结果为 563260223512991±20Hz,相对不确定度为3.6×10^-14.这一数值是直接溯源到铯原子微波频率基准的光学频率测量结果.     

利用光频梳提高台阶高度测量准确度的方法

提出一种利用光频梳和可调谐半导体激光器提高台阶高度测量准确度的方法. 通过将可调谐激光器锁定至光频梳,可对激光器的输出波长进行精确锁定与测量.基于可调合成波长链原理,利用锁定后的半导体激光器构建了一套台阶高度测量方案,该方案可消除合成波长误差对台阶高度测量不确定度的影响. 采用一台可调谐半导体激光器和光频梳进行了5000 s的连续锁定实验, 结果表明,锁定后的可调谐半导体激光器的频率稳定度达 1.8×10^-12.该方法的理论测量不确定度约为7.9 nm, 且测量结果可溯源至时间频率基准.     

周期极化KTiOPO4晶体和频单块非平面环形腔激光产生连续单频589nm黄光

单次通过周期极化KTiOPO₄晶体和频单块非平面环形腔1064 nm与1319 nm激光产生连续单频589 nm黄光. 通过琼斯矩阵模拟计算对单块非平面Nd:YAG晶体参数进行了优化设计, 实验获得1080 mW和580 mW的连续单频1064 nm和1319 nm激光输出. 两束激光单次通过周期极化KTiOPO₄晶体和频产生14.8 mW, M²=1.14的589 nm黄光, 相应的和频效率为0.9%. 研究了周期极化KTiOPO₄温度对和频效率的影响, 得到其温度接收带宽为1.5℃. 通过改变1064 nm Nd:YAG晶体的温度可实现589 nm黄光波长精确对应钠原子D_2a吸收谱线, 调谐精度达到0.164 pm.     

基于双折射双频激光器中的调频回馈位移测量研究

提出了一种基于双折射双频激光器中的调频回馈效应的位移测量系统，并在实验和理论两方面进行了研究.实验中保持回馈外腔长度不变，将一四分之一波片置于激光器内腔中，调制内腔长度，激光器的中心频率发生改变，激光器输出强度将发生周期性的变化.研究发现激光强度曲线的波动频率正比于回馈外腔长度与内腔长度之比.当该位移测量系统的外腔长度是内腔长度的6倍时，被测物体每移动半个光波长，激光强度波动12次，系统分辨率可以达到二十四分之一光波长.理论分析与实验结果相符合.研究表明该位移测量系统具有高分辨率、大测量范围、可工作于任意回馈水平等特点. 关键词： 调频回馈 位移测量 双折射双频激光器 强度波动频率     

Micromachining of copper using Nd:YAG laser radiation at 1064, 532, and 355 nm wavelengths

The interaction phenomena of nanosecond time period Q-switched diode-pumped Nd:YAG laser pulses using 1064, 532 and 355 nm with 0.25 mm thick pure-copper foil was investigated at an incident laser intensity range of 0.5–57.9 GW/cm². For each sample, etch rate and surface structure were determined. Analysis of the results of the tests included scanning electron microscopy (SEM). A maximum etch rate of 13.3 μm per pulse was obtained for the etch rate tests carried out at 532 nm. The maximum etch rate obtainable for 1064 nm was 2.21 μm per pulse, and for 355 nm, 6.68 μm per pulse. The dramatic decrease in etch rate observed when processing at 1064 nm is thought to occur due the highly reflective nature of copper as the interaction wavelength is increased, plus the nature of the plasma formed above the material during the high-intensity laser–material interaction. This plasma then imparts energy to the surface of the processed area leading to surface melting of the area surrounding the hole as can be seen by the SEM photographs.     

光梳主动滤波放大实现锶原子光钟二级冷却光源

提出一种结合注入锁定技术的主动滤波放大方法,将光梳直接注入锁定至光栅外腔半导体激光器,产生窄线宽激光光源,该光源可以用于锶原子光钟二级冷却.实验中,将中心波长为689 nm,带宽为10 nm的光梳种子光源注入689 nm光栅式外腔半导体激光器,通过半导体增益光谱与半导体光栅外腔,从飞秒光梳的多个纵模梳齿中挑选出一个纵模模式来进行增益放大,再通过模式竞争,实现单纵模连续光输出;同时,光梳的重复频率锁定在线宽为赫兹量级的698 nm超稳激光光源上,因此,注入锁定后输出的窄线宽激光也继承了超稳激光光源的光谱特性.利用得到的输出功率为12 mW的689 nm窄线宽激光光源实现了88Sr原子光钟的二级冷却过程,最终获得温度为3μK,原子数约为5×10~6的冷原子团.该方法可拓展至原子光钟其他光源的获得,从而实现原子光钟的集成化和小型化.     

铷原子饱和吸收光谱与偏振光谱对780nm半导体激光器稳频的比较

将激光频率锁定于合适的参考频率,可以有效地抑制激光器的频率起伏。本文采用铷原子D2线超精细跃迁线的饱和吸收光谱和偏振光谱分别获得鉴频曲线,通过电子伺服系统将频率校正信号负反馈到780 nm光栅外腔反馈半导体激光器外腔的压电陶瓷上的方法对激光器进行稳频。介绍了两种方法的基本原理和实验方案。与激光器自由运转300s时激光器典型的频率起伏约6.6 MHz相比,采用饱和吸收光谱和偏振光谱进行稳频,运转300 s时激光器典型的残余频率起伏分别约为1.5 MHz和0.6 MHz。分析表明,饱和吸收光谱稳频采用了相敏检波技术,需要对激光器进行频率调制,带来了额外的频率噪声,而偏振光谱稳频则是一种完全无频率调制的稳频方案。     

超热电子的产生与输运背向辐射的实验研究

报道了在100TW fs激光器上采用电子磁谱仪和光学CCD积分成像相机分别对激光-固体靶相互作用在靶背方向产生的超热电子能谱及其光学渡越辐射进行的测量.能谱测量结果显示:超热电子能谱呈单温类-麦克斯韦分布,拟合的温度为107 keV;光学渡越辐射(OTR)测量结果显示:OTR是由于超热电子输运穿越固体靶所致,而辐射区域呈圆盘状、有发散角、有光强分布;如果考虑超热电子的产生和加热机制,则占主导地位的加热机制是共振吸收对电子的加热.     

铷原子饱和吸收光谱与偏振光谱对780nm半导体激光器稳频的比较

将激光频率锁定于合适的参考频率,可以有效地抑制激光器的频率起伏。本文采用铷原子D2线超精细跃迁线的饱和吸收光谱和偏振光谱分别获得鉴频曲线,通过电子伺服系统将频率校正信号负反馈到780 nm光栅外腔反馈半导体激光器外腔的压电陶瓷上的方法对激光器进行稳频。介绍了两种方法的基本原理和实验方案。与激光器自由运转300s时激光器典型的频率起伏约6.6 MHz相比,采用饱和吸收光谱和偏振光谱进行稳频,运转300 s时激光器典型的残余频率起伏分别约为1.5 MHz和0.6 MHz。分析表明,饱和吸收光谱稳频采用了相敏检波技术,需要对激光器进行频率调制,带来了额外的频率噪声,而偏振光谱稳频则是一种完全无频率调制的稳频方案。     

Spectroscopic studies of laser-produced plasmas formed in CO and CO2 using 193, 266, 355, 532 and 1064 nm laser radiation

The wavelength dependence of laser-produced breakdown in air, CO and CO₂ has been studied using the four Nd:YAG harmonics (266 nm, 355 nm, 532 nm and 1064 nm) and the ArF-excimer laser (193 nm). Breakdown thresholds at these wavelengths are reported for air, CO and CO₂. A significant reduction in the breakdown thresholds for both CO and CO₂ is apparent when comparing 193 nm with the four Nd:YAG harmonics. This reduction is attributed to the resonance-enhanced two-photon ionization of metastable carbon atoms generated in the laser focus at the ArF-laser wavelength. In addition to reporting breakdown thresholds, the laser-produced plasmas in CO and CO₂ are characterized in terms of plasma temperatures and electron densities which are measured by time-resolved emission spectroscopy. Electron densities range from 9 × 10¹⁷ cm^–3 to 1 × 10₁₇ cm^–3. Excitation temperatures range from 22 000 K at 0.2 µs to 11 000 K at 2 µs. Ionization temperatures range from 22 000 K at 0.1 µs to 16 000 K at 2 µs. Evidence is presented to indicate that, like ArF-laser-produced plasmas, Nd:YAG-laser-produced plasmas formed in CO and CO₂ are in or near a state of Local Thermodynamic Equilibrium (LTE) soon after their formation.     

激光单稳频指标的激光计量红外光谱仪精度分析

在傅里叶变换红外光谱仪中,采用激光计量光程差可提高光谱的测量精度。激光波长作为光程差测量的基准单位,其线宽和稳频特性直接决定了光程差的误差,进而影响光谱的测量精度。根据光谱仪的干涉原理,通过傅里叶逆变换和误差分析方法,建立了光谱测量相对误差与激光单稳频指标之间的理论模型,并对该模型进行了仿真计算。结果证明,该模型可作为设计激光计量光程差光谱仪系统的理论依据。     

Numerical study on the efficient generation of 351 nm broadband pulses by frequency mixing of broadband and narrowband Nd: glass lasers

Efficient frequency-tripling of phase-modulated broadband Nd:glass laser pulses is of interest to inertial confinement fusion. We report and theoretically study an efficient frequency-tripling scheme for 351 nm broadband pulses generation by use of broadband and narrowband Nd:glass lasers. Based on the conventional two-crystal doubling and tripling baseline configuration, employing an additional narrowband laser can increase the bandwidth acceptance of Nd:glass up to 320 GHz, which is 3.5 times larger than that of using the conventional configuration. The proposed scheme may also dramatically reduce the conversion of amplitude modulation from the frequency modulation. The efficiency sensitivities on both the fundamental intensity and the doubler orientation are discussed for practical applications.     

A novel frequency encoded all optical CNOT gate exploiting difference frequency generation and implementation of fast binary adders using frequency encoding and nonlinear dielectric films

Optics has an important role in logic implementation and computation is established in two and half decades by many researchers. Recently frequency encoding technique is established. This technique does not suffer from intensity dependent loss problems like other schemes. Amorphous dielectric thin films with reflecting edges can also be used for logic realization and has very fast response speed. It also does not use any semiconductor device and simple to construct. In this communication the authors have proposed all optical CNOT gate using frequency encoded difference frequency generation exploiting nonlinear response of some material and implementation of binary adders by CNOT gate and dielectric thin film AND gate.     

Photonic generation of power-efficient FCC-compliant ultra-wideband waveforms using semiconductor optical amplifier （SOA）： theoretical analysis and experiment verification

We theoretically design a power-efficient ultra-wideband pulse generator by combining three monocycle pulses with different weights. We also experimentally demonstrate a feasible scheme to generate such power-efficient ultra-wideband waveforms using cross-phase modulation in a single semiconductor optical amplifier. The designed ultra-wideband pulse fully satisfies the requirements for the spectral mask specified by the Federal Communications Commission with high power efficiency. In the experiment, a power-efficient ultra-wideband waveform with a pulse duration of 310 ps is achieved, and the power efficiency is greatly improved compared with that of a single monocycle pulse or a mixture of two monocycles.