热致液晶共聚酯酰胺／PET共混物的流变性能和原位增强特性

采用Ｉｎｓｔｒｏｎ３２１１型毛细管流变仪研究了ＰＥＡ／ＰＥＴ共混物的流变性能，据此探讨共混物熔体的可纺性，讨论了共混物配比与复合纤维力学性能的关系，并且偏光显微镜，扫描电镜研究纤维的结构。结果表明，共混物的表观粘度低于ＰＥＴ的粘度，当ＰＥＡ为１０％，共混物的表观粘度达到最小值；且ＰＥＡ含量低于１０％时，共混物的可纺性即，表现出良好的原位增强效果。     

高密度聚乙烯与乙烯丙烯辛烯—1共聚物共混体系的相容性

用ＤＳＣ和ＷＡＸＤ方法研究了高密度聚乙烯／聚（乙烯丙烯辛烯－１）（ＨＤＰＥ／ＥＰＯ）共混体系的结晶性能。共混物的ＤＳＣ曲线皆呈单峰，表明共混体系形成了共晶。晶胞参数ａ及结晶度随共混物组成而变，进一步证明ＨＤＰＥ／ＥＰＯ共混体系的相容性。     

高密度聚乙烯与乙烯丙烯辛烯－1共聚物共混体系的相容性

用ＤＳＣ和ＷＡＸＤ方法研究了高密度聚乙烯／聚（乙烯丙烯辛烯－１）（ＨＤＰＥ／ＥＰＯ）共混体系的结晶性能。共混物的ＤＳＣ曲线皆呈单峰，表明共混体系形成了共晶。晶胞参数ａ及结晶度随共混物组成而变，进一步证明ＨＤＰＥ／ＥＰＯ共混体系的相容性．     

用动态粘弹函数关系表征PMMA／α—MSAN共混物的相分离

测定了聚甲基丙烯酸甲酯／聚（α－甲基苯乙烯丙烯腈）共混物熔体的动态粘弹性，考察动态储能模量Ｇ与动态损耗模量Ｇ的关系，发现在终端区域两种聚合物的ｌｇＧ－ｌｇＧ＾ｎ关系曲线与温度无关，其外推直线斜率接近２；而其共混物的斜率明显小于２，并随组成变化呈现温度依赖性，由此得到的“临界温度”可用于表征这生活上人有ＬＣＳＴ行为的共混物的相容性。     

用动态粘弹函数关系表征PMMA/α-MSAN共混物的相分离

测定了聚甲基丙烯酸甲酯／聚（α－甲基苯乙烯丙烯腈）共混物熔体的动态粘弹性．考察动态储能模量Ｇ′与动态损耗模量Ｇ″的关系，发现在终端区域两种聚合物的ｌｇＧ′～ｌｇＧ″关系曲线与温度无关，其外推直线斜率接近２；而其共混物的斜率明显小于２，并随组成变化呈现温度依赖性，由此得到的“临界温度”可用于表征这种具有ＬＣＳＴ行为的共混物的相容性．     

PEO／EVA共混物的结构研究

ＰＥＯ以分散相形式存在于ＰＥＯ／ＥＶＡ共混物中，且具有部分相容性。Ｘ－射线衍射谱表明ＥＶＡ含有较强的ＰＥ衍射峰；ＰＥＯ／ＥＶＡ共混物既表现出ＰＥ的衍射峰也含有ＰＥＯ的晶面反射。随着ＰＥＯ的Ｍｎ的增加，ＰＥＯ／ＥＶＡ的Ｗｃ、ｘ增大且于时获得最大值：ＰＥ０／ＥＶＡ的Ｗｃ、ｘ值比纯ＰＥＯ的Ｗｃ、ｘ明显降低。     

芳香族热致液晶聚（对羟基苯甲酸－对苯二甲酸双酚A酯）的流变性能

用Ｉｎｓｔｒｏｎ３２１１型毛细管流变仪研究了以对羟基苯甲酸（ＰＨＢ）、对苯二甲酸（ＴＰＡ）和双酚Ａ（ＢＰＡ）为单体合成的共聚芳酯液晶熔体的流变性能。结果表明，切变速率、熔体温度及ＰＨＢ链节含量对切粘度和结构粘度有很大的影响。切变速率在１０～１０３／Ｓ、温度２９５～３３０℃范围内，共聚酯粘流活化能△Ｅη为７４．５～２０５．１（ｋＪ／ｍｏｌ）。液晶熔体在剪切流中存在屈服应力τｏ，随温度升高τｏ值降低。在低温、低切变速率下，共聚酯熔体的弹性很小，甚至呈现挤出收缩现象。     

二氧化硅负载胺丙基硅烷电流变流体

研究用二氧化硅负载胺丙基三乙氧基硅烷［ＮＨ２（ＣＨ２）３Ｓｉ（ＯＥｔ）３］作为分散颗粒，制备无水型的电流变（ＥＲ）流体．考察电场强度（Ｅ）、剪切速率（γ·）、分散颗粒含量、分散介质种类以及极性小分子等因素对ＥＲ流体流变性能的影响．结果发现，以硅油为分散介质，含分散颗粒为１５％（ｇ／ｍｌ）的流体，不添加任何活化剂，在γ·为８０６６ｓ－１时，Ｅ从０升至１６６６ｋＶ／ｍｍ，流体的表现粘度（ηａ）从０３９６Ｐａ．ｓ增大到１６６６８Ｐａ．ｓ．γ·提高，ηａ降低．分散颗粒含量增加，ηａ增大．用硅油作分散介质，ＥＲ效应比用矿物油或石蜡油显著．加入极性小分子苯胺，可以增强流体的ＥＲ效应，但随着苯胺含量增多，漏电流密度也增大．     

热致液晶PEI与PES—C共混物的研究

通过熔融共混,制备不同配比（２．５／９７．５－７５／２５）的ＰＥＩ／ＰＥＳ－Ｃ共混物,使用ＷＡＸＤ、ＤＳＣ、锥板流变仪、力学性能测试、ＳＥＭ等方法对共混物进行了研究。共混后强度、模量均有提高,在高剪切速率下,共混物的粘度有所降低。扫描电镜照片显示,共混物具有“皮芯”结构。     

茂金属聚乙烯的流变性与加工性

研究了丁烯 １ 共聚的茂金属聚乙烯（ｍＰＥ） 的流变性,发现茂金属聚乙烯的窄分子量分布导致它在挤出加工剪切速率范围里熔体粘度高、对剪切敏感性差以及熔体从牛顿型转为非牛顿型所需的剪切速率、转变应力高,在挤出加工条件下流动性差,加工困难．对茂金属聚乙烯（ｍＰＥ） 进行改性制得ＭｍＰＥ,ＭｍＰＥ 熔体对温度、剪切速率的敏感性提高,在加工温度、加工剪切速率范围里的表观粘度降低,加工流动性得到了显著的改进,可在普通聚乙烯加工设备上,制备性能优良的茂金属聚乙烯薄膜制品．     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

探究“铁的锈蚀条件”实验创新设计

设计了铁的锈蚀实验,说明了铁钉的处理方法,增加了温度、酸、碱的影响条件,实现了铁跟蒸馏水及空气中氧气快速反应而生锈,使实验在5 min左右就能够得到准确的结果。