Determination of Al, Cu, Fe, Mn, Pb and Zn in certified reference materials using the optimized BCR sequential extraction procedure

Sequential extraction procedures are widely used to characterize the fractionation of metal species in solid media. With the variety of different sequential procedures used in environmental and geochemical exploration studies, it is difficult to compare results between studies. Thus, harmonization and standardization are required to provide greater inter-study comparability for fraction-specific metals. In this study, the optimized BCR three-step sequential extraction procedure is applied to five certified reference materials (SRM 2710, SRM 2711, CRM 483, CRM 601 and CW 7). Four fractions are reported, acid extractable, reducible, oxidizable, and residual for Al, Cu, Fe, Mn, Pb and Zn. The objectives of this study were to characterize experimental precision and/or accuracy and to establish baseline data of fraction-specific element concentrations for future studies applying the optimized BCR three-step extraction procedure. The optimized procedure was found to be precise (typically <5%) for all metals in all fractions. Accuracy was acceptable (typically ±15% relative to published indicative values for Cu, Pb and Zn for CRM 483 and CRM 601) for all individual fractions. Detailed fraction-specific concentration data are presented, based on five replicates, for the first time using the optimized procedure for Al, Fe and Mn in CRM 483 and CRM 601, and for Al, Cu, Fe, Mn, Pb and Zn in SRM 2710, SRM 2711 and CW 7.     

The utilization of modified BCR three-step sequential extraction procedure for the fractionation of Cd, Cr, Cu, Ni, Pb and Zn in soil reference materials of different origins

A modified three-step sequential extraction procedure for the fractionation of heavy metals, proposed by the Commission of the European Communities Bureau of Reference (BCR) has been applied to the Slovak reference materials of soils (soil orthic luvisols, soil rendzina and soil eutric cambisol), which represent pedologically different types of soils in Slovakia. Analyses were carried out by flame or electrothermal atomic absorption spectrometry (FAAS or ETAAS). The fractions extracted were: exchangeable (extraction step 1), reducible-iron/manganese oxides (extraction step 2), oxidizable-organic matter and sulfides (extraction step 3). The sum of the element contents in the three fractions plus aqua-regia extractable content of the residue was compared to the aqua-regia extractable content of the elements in the origin soils. The accuracy obtained by comparing the determined contents of the elements with certified values, using BCR CRM 701, certified for the extractable contents (mass fractions) of Cd, Cr, Cu, Ni, Pb and Zn in sediment following a modified BCR-three step sequential extraction procedure, was found to be satisfactory.     

Utilization of optimized BCR three-step sequential and dilute HCl single extraction procedures for soil-plant metal transfer predictions in contaminated lands

The prediction of soil metal phytoavailability using the chemical extractions is a conventional approach routinely used in soil testing. The adequacy of such soil tests for this purpose is commonly assessed through a comparison of extraction results with metal contents in relevant plants. In this work, the fractions of selected risk metals (Al, As, Cd, Cu, Fe, Mn, Ni, Pb, Zn) that can be taken up by various plants were obtained by optimized BCR (Community Bureau of Reference) three-step sequential extraction procedure (SEP) and by single 0.5 mol L(-1) HCl extraction. These procedures were validated using five soil and sediment reference materials (SRM 2710, SRM 2711, CRM 483, CRM 701, SRM RTH 912) and applied to significantly different acidified soils for the fractionation of studied metals. The new indicative values of Al, Cd, Cu, Fe, Mn, P, Pb and Zn fractional concentrations for these reference materials were obtained by the dilute HCl single extraction. The influence of various soil genesis, content of essential elements (Ca, Mg, K, P) and different anthropogenic sources of acidification on extraction yields of individual risk metal fractions was investigated. The concentrations of studied elements were determined by atomic spectrometry methods (flame, graphite furnace and hydride generation atomic absorption spectrometry and inductively coupled plasma optical emission spectrometry). It can be concluded that the data of extraction yields from first BCR SEP acid extractable step and soil-plant transfer coefficients can be applied to the prediction of qualitative mobility of selected risk metals in different soil systems.     

Comparison of three sequential extraction procedures (original and modified 3 steps BCR procedure) applied to sediments of different origin

The 3 steps sequential extraction procedure proposed by the Standards Measurements and Testing program (SM&T--formerly BCR) of the European Union has been applied for the speciation of metals in sediments. Results obtained by the application of the BCR standardized procedure were compared to those of two four step sequential extraction procedures, which are different from the BCR procedure only for the introduction of an additional step with NaOCl, as 2nd and 3rd step respectively. Five different metals have been taken into consideration: Cd, Cu, Ni, Pb and Zn. The analytical performances of the laboratory have been evaluated using three certified reference materials: the BCR 601 lake sediment for the BCR sequential extraction procedure, PACS-1 and MESS-1 for total metal concentration. Results showed that the efficiency of NaOCl treatment is higher or at least equal to that of H2O2 treatment and that its selectivity is quite satisfying. Moreover the NaOCl treatment doesn't significantly influence the extraction of the easily reducible fraction.     

New Sediment and Soil CRMs for Extractable Trace Metal Content

Abstract

The lack of uniformity in leaching procedures used to measure broadly defined forms of heavy metals does not allow the results to be compared world-wide nor the methods to be validated since the results obtained are “operationally defined”. An attempt was made to certify several mineral soils CRMs for single extraction by using acetic acid, EDTA and DTPA for Cd, Cr, Cu, Ni, Pb and Zn. Recently, to complete the series of soil CRMs, an organically enriched soil was prepared SO25. For sediments a CRM 601 was produced and certified for metals extractable by using the BCR three step sequential extraction. Not all the trace elements were certified and only indicative values were given for some of them due to poor reproducibility. We performed a systematic study of the effect of the variables identified as potential sources of uncertainty in the use of this scheme. With this study the sources of uncertainty were revealed and an optimised version of the protocol was proposed. With this new version it was possible to certify all the trace elements studied. New sediment material S33 is now proposed for certification and additional data are given for the sediment CRM 601. This modified procedure was also applied to a soil CRM 483 and good results were obtained. This procedure may thus be applied to polluted soils.     

Assessment of trace metals contamination in estuarine sediments using a sequential extraction technique and principal component analysis

Fractionation of the metals Cd, Cr, Cu, Ni, Pb and Zn in sediments was performed for samples collected from eight locations in the Poxim river estuary of Sergipe State, northeast Brazil, using the 3-stage sequential extraction procedure proposed by the European Community Bureau of Reference (BCR). The extraction method was found to be satisfactory for analysis of certified reference material BCR-701, with recovery values ranging from 85% (Cu) to 117% (Cr). The detection limits obtained were 0.001 to 0.305 µg g^− 1. Zn exhibited greatest mobility and bioavailability, indicative of anthropogenic sources, while Cr was mainly found in the residual fraction and could be used as an indicator for the contribution from natural sources. Cd, Cu, Ni and Pb were associated with the oxidizable fraction, and Pb, Cr and Ni with the reducible fraction. Principal component analysis (PCA) clearly separated the metals into three groups: I (Zn); II (Pb); III (Cd, Cu, Cr and Ni). These groupings were mainly due to different distributions of the metals in the various fractions, in sediments from the different locations. Risk assessment code (RAC) analysis indicated that although the metals presented a moderate overall risk to the aquatic environment, nickel showed a low risk (RAC < 10%) at three sites, while zinc presented a high risk (RAC > 30%) at four other sites.     

A comparison of an optimised sequential extraction procedure and dilute acid leaching of elements in anoxic sediments, including the effects of oxidation on sediment metal partitioning

The effect of oxidation of anoxic sediment upon the extraction of 13 elements (Cd, Sn, Sb, Pb, Al, Cr, Mn, Fe, Co, Ni, Cu, Zn, As) using the optimised Community Bureau of Reference of the European Commission (BCR) sequential extraction procedure and a dilute acid partial extraction procedure (4 h, 1 mol L⁻¹ HCl) was investigated. Elements commonly associated with the sulfidic phase, Cd, Cu, Pb, Zn and Fe exhibited the most significant changes under the BCR sequential extraction procedure. Cd, Cu, Zn, and to a lesser extent Pb, were redistributed into the weak acid extractable fraction upon oxidation of the anoxic sediment and Fe was redistributed into the reducible fraction as expected, but an increase was also observed in the residual Fe. For the HCl partial extraction, sediments with moderate acid volatile sulfide (AVS) levels (1-100 μmol g⁻¹) showed no significant difference in element partitioning following oxidation, whilst sediments containing high AVS levels (>100 μmol g⁻¹) were significantly different with elevated concentrations of Cu and Sn noted in the partial extract following oxidation of the sediment. Comparison of the labile metals released using the BCR sequential extraction procedure (ΣSteps 1-3) to labile metals extracted using the dilute HCl partial extraction showed that no method was consistently more aggressive than the other, with the HCl partial extraction extracting more Sn and Sb from the anoxic sediment than the BCR procedure, whilst the BCR procedure extracted more Cr, Co, Cu and As than the HCl extraction.     

Matrix solid phase dispersion-assisted BCR sequential extraction method for metal partitioning in surface estuarine sediments

The BCR (the Community Bureau of Reference) of the European Union sequential extraction scheme for metal partitioning in estuarine sediments has been accelerated by using a matrix solid phase dispersion (MSPD) approach. The MSPD assisted BCR procedure consists of passing the extractants proposed by conventional BCR protocol (0.11 M acetic acid, 0.1 M hydroxylammonium chloride and 8.8 M hydrogen peroxide plus 1 M ammonium acetate) through the dispersed sample packaged inside a disposable syringe. Different silica-, magnesium- and aluminium-based materials were tested as dispersing agents and sea sand was found to offer the best performances. Variables for assisting the three stages of the BCR protocol were optimized, and accurate results were obtained when assisting the first and the third stages (exchangeable and oxidizable fractions, respectively). However, lack of accuracy was observed when assisting the second step (reducible fraction) and this result agrees with most of the assisted BCR procedures for which extracting the reducible fraction is the most troublesome stage. The organic matter oxidation (third stage) was successfully assisted by passing hydrogen peroxide at 50 °C through the dispersed sample inside de syringe just before passing ammonium acetate. Therefore, the time-consuming and unsafe conventional organic matter oxidation processes, commonly performed even for microwave/ultrasounds assisted BCR procedures, are totally avoided. Inductively coupled plasma-mass spectrometry (ICP-MS) was used as a selective detector. The target elements were Cd, Co, Cr, Mn, Ni, Sr and Zn (first stage), Cd, Co and Ni (second stage), and Co, Cr, Mn, Ni, Sr and Zn (third stage). Repeatability of the method (n = 7) was good, and RSDs values of 9, 10, 10, 8, 8, 3 and 8% was obtained for Cd, Co, Cr, Mn, Ni, Sr and Zn, respectively (first stage); 10, 9 and 9% for Cd, Co and Ni, respectively (second stage); and 6, 2, 3, 4, 7 and 9% Co, Cr, Mn, Ni, Sr and Zn, respectively (third stage). The procedure was also validated by analysing two certified reference materials (CRM 601 and CRM 701). Good accuracy was obtained for the target elements extracted at the first stage: Cd (4.0 ± 0.1 and 7.3 ± 0.09 μg g⁻¹ in CRM 601 and CRM 701, respectively), Cr (0.36 ± 0.008 and 2.21 ± 0.08 μg g⁻¹ in CRM 601 and CRM 701, respectively), Ni (8.0 ± 0.3 and 15.4 ± 0.3 μg g⁻¹ in CRM 601 and CRM 701, respectively) and Zn (262 ± 3 and 203 ± 3 μg g⁻¹ in CRM 601 and CRM 701, respectively). Also, good accuracy was observed for elements extracted at the third step: Cd (1.8 ± 0.09 and 0.29 ± 0.03 μg g⁻¹ in CRM 601 and CRM 701, respectively), Cr (145 ± 4 μg g⁻¹ in CRM 701), Ni (8.2 ± 0.7 and 15.1 ± 0.5 μg g⁻¹ in CRM 601 and CRM 701, respectively) and Zn (45 ± 0.7 μg g⁻¹ in CRM 701).     

Ultrasound and microwave-assisted extraction of metals from sediment: a comparison with the BCR procedure

In this paper we investigate alternatives to mechanical stirring for the extraction of the mobile fraction of metals from sediment, and analyze whether these techniques can reduce extraction time and improve reproducibility. We compare the quantities of metal extracted from BCR601 and BCR701 certified sediments using ultrasound bath, microwave-assisted extraction and the first step in the certified BCR sequential extraction procedure. Some environmentally important not-certified metals such as As, Mn, Co, Fe and Al have been included in this study. In the case of microwave-assisted extraction, we compare tests in which samples are exposed to constant, low power irradiation with tests using pulsed high power.

In the tests using the ultrasound bath, less metal was extracted than with the other extractive techniques and standard deviations were comparable to those obtained with the BCR procedure; in assays using microwaves at constant power, extraction efficiencies were different for different metals and for different reference materials and, in some cases, standard deviations were higher than those for the reference method. In contrast, tests with microwaves and constant temperature produced encouraging results: R.S.D.s lay in the 2–4% range, both for certified and not-certified metals; these values are very low compared to those for the reference method. Extraction efficiencies for certified metals were close to 100% for Cd, Zn, Cu and Ni and around 80% for Pb and Cr.     

Metal fractionation in olive oil and urban sewage sludges using the three-stage BCR sequential extraction method and microwave single extractions

The conventional three-stage BCR sequential extraction method was employed for the fractionation of heavy metals in sewage sludge samples from an urban wastewater treatment plant and from an olive oil factory. The results obtained for Cu, Cr, Ni, Pb and Zn in these samples were compared with those attained by a simplified extraction procedure based on microwave single extractions and using the same reagents as employed in each individual BCR fraction. The microwave operating conditions in the single extractions (heating time and power) were optimized for all the metals studied in order to achieve an extraction efficiency similar to that of the conventional BCR procedure. The measurement of metals in the extracts was carried out by flame atomic absorption spectrometry. The results obtained in the first and third fractions by the proposed procedure were, for all metals, in good agreement with those obtained using the BCR sequential method. Although in the reducible fraction the extraction efficiency of the accelerated procedure was inferior to that of the conventional method, the overall metals leached by both microwave single and sequential extractions were basically the same (recoveries between 90.09 and 103.7%), except for Zn in urban sewage sludges where an extraction efficiency of 87% was achieved. Chemometric analysis showed a good correlation between the results given by the two extraction methodologies compared. The application of the proposed approach to a certified reference material (CRM-601) also provided satisfactory results in the first and third fractions, as it was observed for the sludge samples analysed.     

Development of fast thermal programs in electrothermal atomic absorption spectrometry using hot injection and removal of the ashing stage for determination of heavy metals in sequential extracts from sediments

In this work, a fast thermal methodology is developed for the determination of leachable Cu, Cr, Ni and Pb in sediments by electrothermal atomic absorption spectrometry. Fast thermal programs were tried using hot injection, removal of the ashing stage and matrix modifier and their performance compared with that obtained under conventional thermal programs. For this purpose, the BCR three-stage sequential extraction scheme was applied for partitioning of Pb, Cu, Ni and Cr. CRM BCR 601 lake sediment, which is provided with certified values for the extractable contents of the above metals according this scheme, was used for validation.A shortening of the measurement time by a factor of 3-4 was attained without losing analytical performance. Additionally, other features for speeding up determinations such as calibration are considered. Thus, specifically designed fast thermal programs allowed calibration with matrix-matched standards with extractants to be performed for most metals and fractions instead of standard additions. Background signals, LODs, repeatability and sensitivity were generally similar with both types of programs, hence yielding a comparable analytical performance.     

INAA and PIXE for the determination of the contents of extractable sediment

The three-stage BCR sequential step reference extraction procedure was applied to the reference material BCR CRM 601, especially developed for fractionation studies. Extracted fractions were analyzed for Cr, Ni, Zn, Cd, and Pb, by k ₀-standardized instrumental neutron activation (k ₀ INAA) and proton induced X-ray emission (PIXE), and flame atomic absorption spectrometry (FAAS). Sample preparation procedures were developed for both k ₀ INAA and PIXE techniques, related to the evaporation of the solutions in order to get solid samples for neutron and proton irradiation. Quality control was assessed by intercomparison of the analytical results obtained by the applied techniques, which included results for a few certified reference materials. In the extracted fractions, chromium concentration was not determined accurately by both nuclear techniques. Concerning Cd, Ni, Pb, and Zn, the results were in general in good agreement with the certified values and FAAS. Some incomplete separation of the residue might have occurred.     

Comparative study of optimised BCR sequential extraction scheme and acid leaching of elements in the certified reference material NIST 2711

The optimised BCR sequential extraction procedure and a 4 h 1 mol L⁻¹ HCl partial extraction have been performed on the NIST 2711 reference material for a suite of 12 elements (Cd, Sb, Pb, Al, Cr, Mn, Fe, Co, Ni, Cu, Zn, As) using magnetic sector ICP-MS. A pseudo-total aqua regia digest of NIST 2711 has also been undertaken for quality assurance purposes, and comparison of the sum of the four BCR fractions, which included an aqua regia digest on the residue, with the pseudo-total aqua regia digest has been used to assess the accuracy of the BCR partitioning approach. As a result of this work, discrepancies between previous studies about BCR partitioning of elements in NIST 2711 have been discussed and an increase in confidence about the use of BCR partitioning scheme on seven elements (Cd, Pb, Al, Mn, Fe, Cu, Zn) in this standard material has been obtained. On the other hand, BCR partitioning for Sb, Cr, Co, Ni and As has been provided for the first time. Partial extraction results are also reported for the same 12 elements analysed by the optimised BCR procedure, with the partial extraction results exhibiting a strong correlation with the sum of the three labile steps of the BCR procedure.     

Comparison of the standard SM&T sequential extraction method with small-scale ultrasound-assisted single extractions for metal partitioning in sediments

A single extraction method based on the reagents employed in the SM&T (standards, measurement and testing programme) sequential extraction scheme for partitioning of Cd, Cr, Cu, Ni, and Pb in sediments has been developed. Small-scale extractions adapted to electrothermal atomic absorption spectrometric determinations (i.e. 25 mg mass in 1 mL extractant) have been used for the first time in conjunction with selective reagents using conventional operating conditions (i.e. conductive heating, magnetic stirring) or ultrasound-assisted extraction. Small-scale slurry preparations were implemented for determination of the residual/total metal content. The methodology developed enabled drastic reduction of extraction times, yielding extractable contents in accordance with those obtained by application of the conventional SM&T method, which can be regarded as a standard method. An important saving in the amount of sample and reagents is also achieved with small-scale extractions. Homogeneity of sediments at the mg level proved acceptable - precision was similar for between-batch and within-batch measurements. Method development was performed with CRM BCR 601 lake sediment for which extractable amounts of several metals are known. An application to a "real-world" sediment is also presented.     

Assessment of heavy metals leachability from metallo-organic sorbent-iron humate-with the aid of sequential extraction test

The sequential extraction test, known as a BCR procedure, was used to assess a leachability of heavy metals (Zn, Cd, Pb, Cu) from the metallo-organic sorbent—iron humate—loaded with these metals. The sequential test allowed to discriminate between various fractions of heavy metals, namely the acid-extractable fraction, the fraction bound to Fe oxides, and the fraction bound to organic matter. It was proven that the heavy metals are bound mainly to Fe oxides and organic matter, and thus they may be relatively hardly liberated into the environment. The BCR sequential extraction test exhibited a very good repeatability, when it was applied to the loaded sorbent—relative standard deviations were typically lower than 10%.     

氧化与还原条件下伊通河长春区段沉积物重金属形态特征的对比研究

利用改进的Tessier连续萃取法研究了伊通河长春市自由大桥处不同深度沉积物样品在氧化及还原条件下Cu,Pb,Zn和Ni的形态变化规律,同时分析了沉积物样品中酸可挥发性硫(Acid volatile sulfide,AVS)和同时提取重金属(Simultaneous extract metals,SEM)的含量. 实验结果表明，样品经干燥、研磨处理后,Cu有机/硫化物结合态比例减少40%,锰氧化物结合态的比例显著增加; Pb,Zn和Ni 3种元素有机/硫化物结合态比例均略有下降,变化幅度小于Cu,并重新分配到不同的化学相中. 通过SEM中各金属含量与有机/硫化物结合态中金属含量的对比可知,还原性沉积物中Cu除了与硫化物结合外,很大一部分是以有机物形态存在的,Pb,Zn,Ni,Fe和Mn则主要以硫化物形态存在,各元素形态分析均不同程度地受到萃取剂的影响.     

Ultrasound-Assisted Extraction for the Evaluation of Element Mobility in Bottom Sediment Collected at Mining and Smelting Pb–Zn Ores Area in Poland

The current BCR procedure for metal fractionation recommended by the Standard Measurement and Testing Programme requires rather time-consuming sample pretreatment. Ultrasonic energy seems to be an attractive alternative for leaching metal from solid samples into a liquid extractant phase. This study aims at optimizing ultrasonic extraction in order to replace the BCR method of leaching using acetic acid and to apply the procedure of assessing element mobility in bottom sediment rich in moderately soluble carbonate minerals. The application of ICP-MS allowed the determination of As, Cd, Cr, Cu, Pb, Ni, Tl and Zn in extracts, in a wide range of concentration without any special treatment. Finally, 40’min extraction in an ultrasonic bath was proposed for evaluation of the mobile fraction of As, Cd, Cr, Cu, Pb and Zn as an assessment of environmental risk. The recovery of the ultrasound-assisted extraction in comparison to the shake-filter method, as applied in the common BCR procedure, was slightly higher than 100% for As, Cr and Pb, reasonably high (about 70%) for Cd, Zn and Cd, but did not exceed 21% for Tl. Also, the mobility and extractability (relative mobility) of the studied elements from sediment collected over one year were compares. According to the results obtained after 40’min of ultrasound-assisted extraction it can be concluded that mobility did not change over one year for Cr, Cu, As, Cd, Ni and Tl, but noticeable differences for Zn and Pb were observed. The total content of all studied elements was almost the same in samples taken in the years 2003 and 2004, respectively.     

Determination of bioavailable fractions of Zn, Cu, Ni, Pb and Cd in soils and sludges by atomic absorption spectrometry

The single extraction procedures validated by the standards, measurement and testing programme (formerly BCR), extraction with 0.05 mol l⁻¹ EDTA and 0.43 mol l⁻¹ acetic acid, have been applied to reference materials of soils and sludges with certified total values of elements, in order to determine bioavailable contents of Cd, Cu, Ni, Pb and Zn. These soils, which represent uncontaminated pedologically different types of soils from Slovakia and sludges from city water treatment are characterized for the bioavailable fraction of the metals using the procedures followed by SM&T Programme. Concentrations of the elements under the study in the extracts were determined by flame (FAAS) using calibration curves in appropriate extractants and by electrothermal (ETAAS) atomic absorption spectrometry, using technique of standard additions for the evaluation of the results. The accuracy of the extraction procedures and determinations of the elements in the extracts was controlled using CRM 483 certified for EDTA- and acetic acid-extractable contents of Cd, Cu, Ni, Pb and Zn in sewage sludge amended soil.     

Fractionation of heavy metals in sediment by using microwave assisted sequential extraction procedure and determination by inductively coupled plasma mass spectrometry

In this work, a fast microwave assisted extraction procedure was developed and optimized for the heavy metals (Cu, Ni, Cr, Pb and Cd) partitioning in the three-stage sequential extraction procedure proposed by the European Standards, Measurements and Testing (SM&;T) Program, formerly the Community Bureau of Reference (BCR). The microwave oven procedure was optimized to obtain extraction efficiencies similar to the conventional BCR procedure, in less time, while using smaller volumes of reagents. In the optimization process, three variables (extraction time, ramping time and microwave power) were considered as factors and as a response the concentration of different metal ions in each individual BCR fraction. Interactions between analytical factors and their optimized levels were investigated using a central composite design. Extractable metals obtained by both comparable methodologies were measured by inductively coupled plasma mass spectrometry. With the use of optimal microwave conditions, steps 1–3 of the sequential extraction (including the hydrogen peroxide digestion in step 3) could be completed between 21 and 22 min. Detection limits were between 1 and 18 ng l^{− 1}. The accuracy of the proposed method was checked with a certified reference material (CRM) of Lake Sediment BCR 701. Values obtained were in accordance with those reported for the certified material with only a few exceptions. Different origin sediments (river and marine) were analyzed by both BCR and MW procedures, and the results obtained were comparable according to the t-paired-test for a 95% confidence level.     

Evaluating the mobility of toxic metals in untreated industrial wastewater sludge using a BCR sequential extraction procedure and a leaching test

The distribution and speciation of toxic metals in industrial wastewater sludge (IWS) was investigated. In this work, the modified BCR three-stage sequential extraction procedure was applied to the fractionation of Cr Pb Ni, and Cd in untreated industrial wastewater sludge from industrial sites in Hyderabad (Pakistan). The extracts were analyzed using electrothermal atomic absorption spectrometry. The procedure was evaluated using a certified reference material for soil mixed with sewage sludge BCR 483. The results from the partitioning study indicate that more easily mobilized forms (acid exchangeable) of Cd were dominant. The oxidizable fraction was dominant for all four toxic metals. Metal recovery was good, with <4% difference between the total metal recovered through the extractant steps and the total metal determined after microwave digestion. Lixiviation tests (DIN 38414-S4) were used to evaluate the leaching of toxic species from IWS, and it was observed that levels of leachable toxic metals were low compared to the amount of metal extracted in the exchangeable fraction of the BCR protocol.