Application of co-electroosmotic capillary electrophoresis for the determination of inorganic anions and carboxylic acids in soil and plant extract with direct UV detection

Summary Indirect UV detection in capillary zone electrophoresis (CZE) is frequently used for the determination of inorganic anions and carboxylic acids. However, there are few reports on direct UV detection of these solutes in real samples. This paper describes the use of direct UV detection of inorganic anions and organic acids in environmental samples using co-electroosmotic capillary zone electrophoresis (co-CZE) at 185 nm. The best separation and detection of the solutes was achieved using a fused silica capillary with an electrolyte containing 25 mM phosphate, 0.5 mM tetradecyltrimethylammonium bromide (TTAB) and 15% acetonitrile (v/v) at pH 6.0. Four common inorganic anions (Cl⁻, NO₂ ⁻, NO₃ ⁻ and SO₄ ²⁻) and 11 organic acids (oxalic, formic, fumaric, tartaric, malonic, malic, citric, succinic, maleic, acetic, and lactic acid), were determined simultaneously in 15 min. Linear calibration plots for the test solutes were obtained in the range 0.02–0.5 mM with detection limits ranging from 1–9 μM depending on the analyte. The proposed method was successfully used to determine inorganic anions and carboxylic acids in soil and plant tissue extracts with direct injection of the sample.     

Determination of C1−C4 fatty acids as p-bromophenacyl esters using glass-capillary gas chromatography and electron-capture detection

Summary A method for the determination of low relative molecular mass carboxylic acids (C₁–C₄) in water is reported. The acids are converted to p-bromophenacyl esters prior to a glass-capillary gas chromatographic separation. By utilizing electron-caputre detection the detectability is substantially improved compared to flame-ionization detection. A comparison of three different ways to treat the water samples and to produce the derivatives is made. It is shown that the , p-dibromoacetophenone reagent decomposes to a small extent which limits the utility of the reagent. Nevertheless a detection limit for formic acid of approximately 2.5 mgl^–1 is obtained. The method is applied to the determination of formic and acetic acids in a paper kraft water sample.     

Simultaneous Determination of Organic Acids in Wine Samples by Capillary Electrophoresis and UV Detection: Optimization with Five Different Background Electrolytes

A simple technique is described for the routine capillary electrophoretic determination of organic acids in wine samples. Several aromatic and non‐aromatic compounds, including phthalic acid, benzoic acid, sorbic acid, boric acid, and phosphate, were evaluated as background electrolytes in order to obtain the highest resolution and detection sensivity. Factors that affect capillary electrophoretic separation such as the concentration and pH of the background electrolyte (BGE), the concentration of the electroosmotic flow modifier (EOF), and methanol addition to the electrolyte were investigated systematically. Tartaric, malic, succinic, acetic, and lactic acids were determined simultaneously in approximately six minutes using an electrolyte containing 3 mM phosphate and 0.5 mM myristyltrimethylammonium bromide (MTAB) as electroosmotic flow modifier at pH 6.5. This method is quantitative, with recoveries in the 90–102% range and linear up to 50 mg L^–1. The precision is better than 1% and the procedure shows the appropriate sensibility, with detection limits between 0.015 and 0.054 mg L^–1. The proposed method was successfully employed for the determination of organic acids in wine samples by direct sample injection after appropriate dilution and filtration.     

Determination of organic acids in air by capillary electrophoresis and ion-exclusion chromatography

Summary A capillary electrophoretic (CE) method for the determination of organic acids in the low ppm range is described. The buffer consisted of 5 mM 2,6-pyridinedicarboxylic acid and 0.5 mM cetyltrimethylammonium bromide, pH 5.6. The former served as background electrolyte for indirect UV detection at 200 nm, whereas the latter was used to reverse electroosmotic flow. In <5 min 8 low molecular mass organic acids (oxalic, formic, malonic, glutaric, glycolic, acetic, lactic and propanoic) and two inorganic acids (hydrochloric and sulphuric) were separated. Detection limits for anions tested were 0.04 mg L⁻¹ (lactic acid) to 0.6 mg L⁻¹ (malonic acid). The method was applied to the determination of organic acids in air samples. The CE results when compared with ion-exclusion chromatography (IEC) agreed well. The use of electrokinetic injection in CE proved beneficial for preconcentration of organic acids in real samples. Using electrokinetic injection, preconcentration factors ranging from 14 (hydrochloric acid) to 3 (propanoic acid) were obtained. Presented at Balaton Symposium on High-Performance Separation Methods, Siófok, Hungary, September 1–3, 1999     

Chemiluminometric determination of the pesticide 3-indolyl acetic acid by a flow injection analysis assembly

A new method is proposed for the chemiluminescent determination of the pesticide 3-indolyl acetic acid by means of an flow injection analysis system. The chemiluminescence emission is obtained by oxidation of the analyte with Ce (IV) in nitric acid and presence of β-cyclodextrine.The continuous-flow method allows the determination of 159 samples h⁻¹ of 3-indolyl acetic acid in an interval of concentrations over the range 0.5-15.0 mg l⁻¹. The limit of detection was 0.1 μg l⁻¹ and the R.S.D. (n, 17) at 2.0 mg l⁻¹ of the pesticide level was 2.7%. The method was applied to water samples.     

Analysis of Chlormequat residues in grain using liquid chromatography-mass spectrometry (LC-MS/MS)

A fast, sensitive and specific method for routine determination of residues from Chlormequat (CAS no. 7003-89-6) is described. The method is based on a simple clean-up using an SPE-C₁₈ cartridge, high-performance liquid chromatography on a standard C₁₈ column (Spherisorb S5 ODS1) and specific detection and quantification by electrospray mass spectrometry (LC-MS/MS). ¹³C-Chlormequat was synthesised for use as internal standard. Samples were extracted with methanol – water – acetic acid. Internal standard and ammonium acetate were added before C₁₈-cartridge clean up and residues eluted with methanol – water – acetic acid, containing 50 mM ammonium acetate. Chromatographic separation was achieved using a solvent composed of acetonitrile – methanol – water – acetic acid (53:21:25:1 by volume), containing 50 mM ammonium acetate. Electrospray ionisation mass spectrometry was employed using m/z 58 (daughter ion of the Chlormequat quaternary ammonium ion, m/z 122) and m/z 61 (daughter ion of the ¹³C-Chlormequat quaternary ammonium ion, m/z 125) for quantification. The LC analysis time was 15 min and the limit of detection of the analytical method was 9 μg/kg. The performance of the method was demonstrated analysing grain material from an inter-comparison study. In Denmark the primary use of Chlormequat chloride (CCC, cycocel, or chlorocholin chloride, CAS no. 999-81-5) is for winter cereals and 11 such winter wheat samples from the Danish National Pesticide Survey were analysed. Residue contents were from below 0.01 up to 0.45 mg/kg, and thus below the EU maximum residue level of 2.0 mg/kg for wheat.     

Trace determination of perchlorate using electromembrane extraction and capillary electrophoresis with capacitively coupled contactless conductivity detection

Electromembrane extraction (EME) and CE with capacitively coupled contactless conductivity detection (CE‐C⁴D) was applied to rapid and sensitive determination of perchlorate in drinking water and environmental samples. Porous polypropylene hollow fiber impregnated with 1‐heptanol acted as a supported liquid membrane (SLM) and perchlorate was transported and preconcentrated in the fiber lumen on application of electric field. High selectivity of perchlorate determination and its baseline separation from major inorganic anions was achieved in CE‐C⁴D using background electrolyte solution consisting of 7.5 mM L ‐histidine and 40 mM acetic acid at pH 4.1. The analytical method showed excellent parameters in terms of reproducibility; RSD values for migration times and peak areas at a spiked concentration of 15 μg/L of perchlorate (US EPA recommended limit for drinking water) were below 0.2 and 8.7%, respectively, in all examined water samples. Linear calibration curves were obtained for perchlorate in the concentration range 1–100 μg/L (r²≥0.999) with limits of detection at 1 μg/L for tap water and at 0.25–0.35 μg/L for environmental and bottled potable water samples. Recoveries at 15 μg/L of perchlorate were between 95.9 and 106.7% with minimum and maximum recovery values for snow and bottled potable water samples, respectively.     

Rapid Simultaneous Determination of Eight Benzimidazoles in Animal Feed by LC�CMS�CMS

A rapid, sensitive and reliable LC?CMS?CMS method for the determination of eight benzimidazoles in animal feed was developed and validated. Samples were extracted with acidic acetonitrile. The extract was diluted with 0.1% formic acid in water, and analyzed by LC?CMS?CMS on a Waters XBridge? C₁₈ column with acetonitrile/0.1% formic acid in water as mobile phase. The samples were quantified with the matrix standard calibration curve method. Good linearity was obtained for eight benzimidazoles at a concentration of 0.005?C2.5 ??g mL^?1 with a linear relative coefficient more than 0.990. Recoveries of 84.0?C104.0% with CVs of 2.50?C7.50% were obtained. Limit of detection was 2.1?C63.0 ??g kg^?1. The method demonstrated to be suitable for the determination of eight benzimidazoles in animal feed samples.     

Analysis of Chlormequat residues in grain using liquid chromatography-mass spectrometry (LC-MS/MS)

A fast, sensitive and specific method for routine determination of residues from Chlormequat (CAS no. 7003-89-6) is described. The method is based on a simple clean-up using an SPE-C₁₈ cartridge, high-performance liquid chromatography on a standard C₁₈ column (Spherisorb S5 ODS1) and specific detection and quantification by electrospray mass spectrometry (LC-MS/MS). ¹³C-Chlormequat was synthesised for use as internal standard. Samples were extracted with methanol – water – acetic acid. Internal standard and ammonium acetate were added before C₁₈-cartridge clean up and residues eluted with methanol – water – acetic acid, containing 50 mM ammonium acetate. Chromatographic separation was achieved using a solvent composed of acetonitrile – methanol – water – acetic acid (53:21:25:1 by volume), containing 50 mM ammonium acetate. Electrospray ionisation mass spectrometry was employed using m/z 58 (daughter ion of the Chlormequat quaternary ammonium ion, m/z 122) and m/z 61 (daughter ion of the ¹³C-Chlormequat quaternary ammonium ion, m/z 125) for quantification. The LC analysis time was 15 min and the limit of detection of the analytical method was 9 μg/kg. The performance of the method was demonstrated analysing grain material from an inter-comparison study. In Denmark the primary use of Chlormequat chloride (CCC, cycocel, or chlorocholin chloride, CAS no. 999-81-5) is for winter cereals and 11 such winter wheat samples from the Danish National Pesticide Survey were analysed. Residue contents were from below 0.01 up to 0.45 mg/kg, and thus below the EU maximum residue level of 2.0 mg/kg for wheat. Received: 22 December 1997 / Revised: 29 January 1998 / Accepted: 31 January 1998     

Determination of water in furfural by infrared spectroscopy

The IR absorption band at 5250 cm^–1 is used to determine 0–5% water in furfural. The accuracy of the determination is not less than 5%. The method is suitable for any kind of furfural. The analytical results are unaffected by the presence of formic, acetic, and pyromucic acids, and methanol and ethanol.     

Optimization of Capillary Isotachophoretic Method for Histidine Determination in Protein Matrices

The capillary isotachophoretic method was optimized and used for histidine determination in food samples. The optimum conditions for histidine separation and determination were found on the experimental conditions such as: selectivity, separation speed, pH, concentration of the leading and terminating electrolytes, and electroosmotic flow additives. The optimum electrolytes composition [leading electrolyte: 7 mM NH₄OH + 15 mM 2-(N-morpholino)ethanesulfonic acid + 1% hydroxyethylcellulose; pH = 6.10 and terminating electrolyte: 15 mM aminocaproic acid +5 mM acetic acid +40% methanol; pH = 5.10] and conditions of analysis were adopted for histidine determination in food samples (meat and fish products). The proposed electrolyte system was characterized by linearity (10–100 and 100–430 mg · L^?1 with R² = 0.9976 and 0.9991), accuracy (99.5% and 98%), intra-assay of the relative step height (1.40% for standard and 3.20% for food samples analysis), inter-assay of the relative step height (3.65% and 6.30%) and satisfactory quantification and detection limits. The obtained results were compared to a chromatographic method (reversed-phase (RP)-HPLC) for determination of histidine. The average concentrations of histidine in the samples assayed by both methods were statistically comparable. It should be noted that the proposed histidine determination method can be considered as a contribution to Green Analytical Chemistry.     

Qualitative analysis of some carboxylic acids by ion-exclusion chromatography with atmospheric pressure chemical ionization mass spectrometric detection

A simple, selective and sensitive method for the determination of carboxylic acids has been developed. A mixture of formic, acetic, propionic, valeric, isovaleric, isobutyric, and isocaproic acids has been separated on a polymethacrylate-based weak acidic cation-exchange resin (TSK gel OA pak-A) based on an ion-exclusion chromatographic mechanism with detection using UV-photodiode array, conductivity and atmospheric pressure chemical ionization mass spectrometry (APCI-MS). A mobile phase consisting of 0.85 mM benzoic acid in 10% aqueous methanol (pH 3.89) was used to separate the above carboxylic acids in about 40 min. For LC-MS, the APCI interface was used in the negative ionization mode. Linear plots of peak area versus concentration were obtained over the range 1-30 mM (r2=0.9982) and 1-30 mM (r2=0.9958) for conductimetric and MS detection, respectively. The detection limits of the target carboxylic acids calculated at S/N=3 ranged from 0.078 to 2.3 microM for conductimetric and photometric detection and from 0.66 to 3.82 microM for ion-exclusion chromatography-APCI-MS. The reproducibility of retention times was 0.12-0.16% relative standard deviation for ion-exclusion chromatography and 1.21-2.5% for ion-exclusion chromatography-APCI-MS. The method was applied to the determination of carboxylic acids in red wine, white wine, apple vinegar, and Japanese rice wine.     

Capillary zone electrophoresis for U(VI) and short chain carboxylic acid sorption studies on silica and rutile

Capillary zone electrophoresis was used to study the uranyl and short chain carboxylic acid sorption on silica and rutile. The separation and the simultaneous determination (in a single run) of a number of short chain carboxylic acids (oxalic, formic, acetic and propionic) and U(VI) with direct UV detection is developed for the analysis of solutions after the sorption experiments. The reverse polarity mode is used (the injection is performed at the negative end). The matrix effect of Si(IV) (possible silica dissolution product) and perchlorate (added for constant ionic strength in sorption experiments) on the separation of U(VI) and organic acids is investigated. The influence of methanol addition in carrier electrolyte on the separation selectivity of given analytes is also studied. Under the chosen conditions (carbonate buffer (ionic strength of 0.1 M), pH 9.8, 0.15 mM of tetradecyltrimethylammonium bromide, 25% (v/v) of methanol) the calibration curves are plotted. They are linear in two ranges of concentration from ∼1 × 10⁻⁵ to ∼1 × 10⁻³ M for oxalate, acetate, propionate, U(VI) and ∼1 × 10⁻⁴ to ∼1 × 10⁻³ for formate. The accuracy of the procedure is checked by the “added-found” method in simulation solutions. The relative standard deviations of the concentrations found are within the range of 1-10% and the recovery is in the range of 90-115%. This method is applied for the analysis of aqueous samples issued from sorption experiments on silica and rutile. The obtained results indicate that the given organic acids decrease uranium sorption both on silica and rutile. These experiments demonstrate that short chain carboxylic acids can influence the mobility and the chemistry of U(VI) in the environment.     

阀切换-离子色谱法测定1,2-环氧丁烷产品中有机酸

建立了阀切换-离子色谱法测定1,2-环氧丁烷（1,2-BO）产品中有机酸（甲酸、乙酸和丙酸）的方法。样品经乙醇稀释后,通过阀切换技术,有机酸被IonPac TAC-ULP1捕集柱捕集,然后进入IonPac AS11分析柱分离,并由电导检测器检测。结果表明：甲酸、乙酸和丙酸均能实现较好地分离,在各自的范围内其色谱峰面积呈现良好的线性关系。实际样品的加标回收率为92.5%~111.8%,相对标准偏差小于5.6%（n=3）,检出限为0.60~4.80 μg/L。该方法具有前处理简单、快速、准确等特点,适用于不溶于水的有机体系中有机酸的分析。     

Liquid–Liquid–Liquid Micro Extraction Combined with CE for the Determination of Rare Earth Elements in Water Samples

A simple method for determination of rare earth elements (REEs) by liquid–liquid–liquid microextraction (LLLME) coupled with capillary electrophoresis and ultraviolet technique was developed. In the LLLME system, 40 mmol L^?1 4-benzoyl-3-methy-1-phenyl-5-pyrazolinone (PMBP) acted as extractant and 4% (v/v) formic acid was used as back-extraction solution. The parameters influencing the LLLME, including the type of the organic solvent, sample pH, formic acid concentration, PMBP concentration, extraction time, volume of organic solvent, stirring rate and phase volume ratio, were investigated. Under the optimized conditions, the detection limits (S/N = 3) of REEs were in the range of 0.19–0.70 ng mL^?1. The developed method was successfully applied to the determination of trace amounts of REEs in water samples.     

A validated LC–MS/MS method for fast detection of thiodiglycolic acid in aqueous samples

A novel sensitive screening method based on liquid chromatography–tandem mass spectrometry (LC–MS/MS) has shown the feasibility of separation and detection of thiodiglycolic acid in aqueous samples. The analysis of this compound is of interest since it is specific microbiological metabolite of thiodiglycol, which is precursor and degradation product of chemical warfare agent sulfur mustard. The LC–electrospray ionisation (ESI)–MS method provides a sensitive and direct approach for thiodiglycolic acid identification and quantification using non-extracted non-derivitised samples from aqueous solutions. Chromatographic separation of the thiodiglycolic acid was produced using a reverse phase LC column with gradient mobile phases consisting of 0.1% formic acid in water and acetonitrile. Identification and quantification of species were achieved using ESI–tandem MS monitoring two precursor-to-product ion transitions for thiodiglycolic acid. The method demonstrates linearity over at least two orders of magnitude and detection limit of 10 ng...mL^–1 in environmental water samples.     

Some observations on catalytic conductometric titrations

Conductometric and high-frequency conductometric methods for the determination of the endpoint of catalytic titrations were developed. Titrations of sodium acetate were made in a mixture of acetic anhydride and acetic acid (7:3–11:3) which was 0.05–0.1 mol dm⁻³ in sodium perchlorate. Integral and derivative titration curves were recorded in both coulometric and volumetric titrations. Different acylation reactions, as well as dehydration of formic acid, were used as the indicator reactions. The optimal conditions of determination—choice of volume ratio of acetic anhydride to acetic acid, rate of the titrating reagent addition, concentration of sodium perchlorate, and concentration of several alcohols, water, and formic acid as components of the indicator reactions—were determined. Using the catalytic conductometric method, amounts of 0.04–11 mg of sodium acetate were determined with a relative standard deviation of less than 0.8 and 1.6% in volumetric and coulometric addition, respectively. Using the catalytic high-frequency conductometric method, amounts of 1–11 mg of sodium acetate were determined with relative standard deviation less than 0.5% (volumetrically) or less than 1.4% (coulometrically). The obtained results were compared with those of potentiometric and catalytic thermometric titrations.     

Determination of Monochloroacetic Acid and Dichloroacetic Acid for Quality Control of Acetic Acid Chlorination Industry by Ion Chromatography

An ion chromatographic method is described for the purpose of quality control in the process of monochloroacetic acid production. Using 2.5 mM NaOH–10% methanol as eluent, the simultaneous determination of acetic acid, monochloroacetic acid, dichloroacetic acid, and Cl⁻ was obtained in a single run. Monochloroacetic acid and dichloroacetic acid showed good linearity in the range 0.1–20 and 0.15–20 μg/ml and correlation coefficients were 0.9999 and 0.9998, respectively. The detection limits (signal-to-noise ratio 3:1) of monochloroacetic acid and dichloroacetic acid were 17 and 25 ng/ml. This simple, sensitive, and time-saving method can be applied for composition analysis in acetic acid chlorination production.     

Rapid and simple determination of psychotropic phenylalkylamine derivatives in urine by direct injection liquid chromatography–electrospray ionization–tandem mass spectrometry

A direct injection liquid chromatography–electrospray ionization–tandem mass spectrometric method (LC‐ESI‐MS/MS) was developed and validated for the rapid and simple determination of 13 phenylalkylamine derivatives. Eight deuterium‐labeled compounds were prepared for use as internal standards (ISs) to quantify the analytes. Urine samples mixed with ISs were centrifuged, filtered through 0.22 µm filters and then injected directly into the LC‐ESI‐MS/MS system. The mobile phase was composed of 0.2% formic acid and 2 mM ammonium formate in distilled water and 0.2% formic acid and 2 mM ammonium formate in acetonitrile. The analytical column was a Capcell Pak MG‐II C₁₈ (150 × 2.0 mm i.d., 5 µm, Shiseido). Separation and detection of the analytes were accomplished within 10 min. The linear ranges were 5–750 ng/mL (ephedrine and fenfluramine), 10–750 ng/mL (3,4‐methylenedioxyamphetamine, phendimetrazine, methamphetamine, 3,4‐methylenedioxyethylamphetamine and benzphetamine), 20–750 ng/mL (norephedrine, amphetamine, phentermine and ketamine) and 30–1000 ng/mL (3,4‐methylenedioxymethamphetamine and norketamine), with determination coefficients, R², ≥ 0.9967. The intra‐day and inter‐day precisions were within 19.1%. The intra‐day and inter‐day accuracies ranged from ?16.0 to 18.7%. The lower limits of quantification for all the analytes were lower than 26.5 ng/mL. The applicability of the method was examined by analyzing urine samples from drug abusers (n = 30). Copyright © 2012 John Wiley & Sons, Ltd.     

Separation and determination of the anthraquinones in Xanthophytum attopvensis pierre by nonaqueous capillary electrophoresis

A nonaqueous capillary electrophoresis (NACE) method with direct on-column UV detection has been developed for the separation of the pharmaceutically important anthraquinones from the total grass of Xanthophytum attopvensis pierre extract. The separation of three main anthraquinones (1-hydroxy-2-methoxy-3-hydroxymethyl-9, 10-anthraquinone-1-O-β-d-glucoside (1), rubiadin- 1-methylether (2) and 1-methoxy-2-formyl-3-hydroxy-9, 10-anthraquinone (3)) was optimized with respect to concentration of sodium cholate (SC) and acetic acid, addition of acetonitrile (ACN), and applied voltage. Baseline separation was obtained for the three analytes within 5 min using a running buffer containing 50 mM sodium cholate (SC), 1.0% acetic acid and 40% ACN in methanol. The method of NACE for the separation and determination of bioactive ingredient in traditional Chinese medicines was discussed.