Photopolymerization of methyl methacrylate with the use of iodine monobromide as photoinitiator

Iodine monobromide easily induces photopolymerization of methyl methacrylate (MMA) at 40°C under visible light. Initiator exponent and monomer exponent values were found to be 0.5 and 2, respectively, at low initiator concentrations, while the corresponding values at high initiator concentration conditions were zero and 3. The chain transfer constant of IBr at 40°C was found to be 13.0. Kinetic and other data indicate a radical polymerization mechanism involving complexation of monomer molecules with iodine monobromide prior to radical generation, and termination is believed to take place biomolecularly at low IBr concentrations and unimolecularly, involving reaction with the initiator, at high IBr concentrations (initiator termination).     

Kinetics of photopolymerization of acrylamide initiated by copper (II)–bis(amino acid) chelates in aqueous solution. II

The kinetics of photopolymerization reactions of acrylamide initiated by copper (II)–bis(amino acid) chelates with amino acids glutamic acid, serine, or valine were studied at 30°C. The extent of monomer conversion increases with increased initiator concentration and falls off after reaching a maximum. Analysis of the results shows that for lower concentrations of the initiator, the rate of monomer disappearance is proportional to light absorption fraction f[monomer] and the square root of the intensity. At higher concentrations of the initiator, the rate of monomer disappearance is proportional to F_ε/[initiator]^1/2; the monomer exponent is 1.5 and the intensity exponent 0.5. Mutual termination of the radicals is proposed at lower concentrations of the initiator; at higher concentrations of the initiator termination of the initiator radical by the copper (II) complex along with mutual termination occurs. The initiator radical species is identified from flash photolysis studies of these complexes as the Cu(I)-coordinated radical. The effect of pH on the monomer conversion is explained. The data indicate a free-radical mechanism of polymerization and a reaction scheme is proposed for the polymerization reactions.     

Polymerization of Methyl Methacrylate Using Acridone-Bromine Combination as the Photoinitiator

The photopolymerization of methyl methacrylate (MMA) in visible light was studied at 40°C using the acridone-bromine (acridone-Br₂) combination as the photoinitiator. The polymerization was found to proceed via a free radical mechanism, and the radical generation process was considered to follow an initial complexation reaction between monomer and each initiator component (acridone and Br₂), followed by further interaction between these two initiator-monomer complexes. Kinetic data indicated a lower-order dependence of R on initiator concentrations (initiator exponent < 0.5). Initiator-dependent chain termination was signifi-cant along with the usual bimolecular mode of chain termination. The monomer exponent varied from about 1.00 to 2.00, depending on the nature of solvents used. The nonidealities in this system were also analyzed.     

Use of an Internal Keto-Imino Compound as the Photoinitiator in the Polymerization of Methyl Methacrylate

Photopolymerization of MMA in visible light was studied at 40°C using acridone as the photoinitiator. The polymerization was found to proceed via a free radical mechanism and the radical generation process was considered to follow an initial complexation reaction between monomer and acridone. Kinetic data indicated a lower order dependence of R_p on the initiator concentration (initiator exponent < 0.5). Initiator-dependent chain termination was significant along with the usual bimolecular mode of chain termination. The monomer exponent varied from about 1.0 to 1.5, depending on the nature of the solvent used. The nonidealities in this case were also analyzed.     

Novel solvent effects in the photopolymerization of methyl methacrylate by use of quinoline–bromine charge-transfer complex as photoinitiator

Photopolymerization of MMA was carried out at 40°C in diluted systems by use of quinolinebromine (Q–Br₂) charge-transfer complex as the initiator and chloroform, carbon tetrachloride, chlorobenzene, dioxane, THF, acetone, benzene, toluene, quinoline, and pyridine as solvents. The results showed variable monomer exponents ranging from 1 to 3. For chloroform, carbon tetrachloride, and chlorobenzene, the monomer exponent observed was unity; for other solvents used, the value of the same exponent was much higher (between 2 and 3). Initiation of polymerization is considered to take place through radicals generated in the polymerization systems by the photodecomposition of (Q–Br₂)–monomer complex (C) formed instantaneously in situ on addition of the Q–Br₂ complex in monomer. The kinetic feature of high monomer exponent is considered to be due to higher order of stabilization of the initiating complex (C) in presence of the respective solvents. In the presence of the retarding solvents, very low or zero initiator exponents were also observed, depending on the nature and concentration of the solvents used. The deviation from the square-root dependence of rate on initiator concentration becomes higher at high solvent and initiator concentrations in general. This novel deviation is explained on the basis of initiator termination, probably via degradative chain transfer involving the solvent-modified initiating complexes and the propagating radicals.     

Photopolymerization of methyl methacrylate using a morpholine–sulfur dioxide charge-transfer complex as the photoinitiator

Photopolymerization of the vinyl monomer (M) of methyl methacrylate (MMA) was kinetically studied by using near-UV/visible light at 40°C and employing a morpholine (MOR)–sulfur dioxide (SO₂) charge-transfer (C-T) complex as the photoinitiator. The rate of polymerization (R_P) was found to be dependent on the morpholine: sulfur dioxide mole ratio; the 1 : 2 (MOR–SO₂) complex acted as the latent initiator complex C which underwent further complexation with the monomer molecules to give the actual initiating complex I. Using the 1 : 2 (MOR–SO₂) C-T complex as the latent initiator, the observed kinetics may be expressed as R_P [MOR–SO₂]^0.27[M]^1.10. Benzoquinone behaved as a strong inhibitor. Polymers obtained tested positive for the incorporation of a sulphonate-type end group. Polymerization followed a radical mechanism. Kinetic nonideality as revealed by a low initiator exponent and monomer exponent of greater than unity was explained on the basis of a prominent primary radical termination effect. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1973–1979, 1998     

Aqueous polymerization of methyl methacrylate initiated by the redox system Ce(IV)–isopropyl alcohol. Kinetics and molecular weight

Polymerization of methyl methacrylate was carried out in aqueous nitric acid in the temperature range 26–40°C, with the redox initiator system ceric ammonium nitrate–isopropyl alcohol. A short induction period was observed, as well as the attainment of a limiting conversion, and the total ceric ion consumption with reaction time. The reaction orders were 1/2 and 3/2 with respect to the IPA and monomer concentration, respectively, within the range (3–5) × 10^?3M of Ce(IV). But at lower Ce(IV) concentration (≤ 1 × 10^?3M), the order with respect to monomer and Ce(IV) changed to 1 and 1/2, respectively. The rate of ceric ion disappearance was first order with respect to Ce(IV) concentration and (R_Ce)^?1 was proportional to [IPA]^?1. Both the rate of polymerization and the rate of ceric ion consumption increase with rise in temperature. The average-molecular weight can be controlled by variations in IPA, Ce(IV), and monomer concentrations, and in temperature. A kinetic scheme involving oxidation of IPA by Ce(IV) via complex formation, whose decomposition gives rise to a primary radical, initiation, propagation, and termination of the polymeric radicals by bimolecular interaction is proposed. An oxidative termination of primary radicals by Ce(IV) is also included.     

Photopolymerization of methyl methacrylate with the use of tetrahydrofuran–bromine charge-transfer complex as the photoinitiator

The polymerization of MMA was kinetically studied in the presence of visible light (using a 125-W high-pressure mercury vapor lamp with fluorescent coating, without a filter), a THF—bromine charge-transfer complex being used as the photoinitiator. The initiator exponent was 0.5 in bulk polymerization. The monomer exponent varied from about 1.2 to about 2.5, depending on the nature of the solvent used; the initiator exponent also varied in diluted systems, depending on the nature and proportion of the solvent, the variation being from a value of 0.5 in bulk system to zero or almost zero at about 25% (v/v) solvent concentration. Other kinetic parameters, viz., k_p²/k_t and the activation energy for polymerization, were determined and are reported. Kinetic and other evidence indicates that the photopolymerization takes place by a radical mechanism and termination is bimolecular in nature in bulk systems; in dilute systems, termination by initiator complex assumes predominance, particularly at high solvent concentrations (≥25% v/v).     

Photopolymerization of methyl methacrylate with the use of morpholine-chlorine charge transfer complex as the photoinitiator

Polymerization of methyl methacrylate (MMA) was kinetically studied under photo condition using near UV visible light at 40°C and employing morpholine (MOR)–chlorine (Cl₂) charge transfer (C-T) complex as the photoinitiator. The rate of polymerization (R_p) was dependent on morpholine/chlorine mole ratio; the 1 : 2 (MOR–Cl₂) C-T complex acted as the latent initiator complex, C, which underwent further complexation with the monomer molecules to give the actual initiator complex, I. Using 1 : 2 (MOR-Cl₂) C-T complex as the latent initiator, the initiator exponent evaluated for bulk photopolymerization of MMA was 0.071 and monomer exponent determined from studies of photopolymerization in benzene diluted system was 1.10. Benzoquinone behaved as a strong inhibitor and the polymers tested positive for the incorporation of chlorine atom end groups. Polymerization followed a radical mechanism. Kinetic nonideality as revealed by low (≪0.5) initiator exponent and a monomer exponent of greater than unity were explained in terms of primary radical termination effect. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 1681–1687, 1997     

Polymerization of vinyl chloride at reduced monomer accessibility. II. Polymerization at subsaturation pressure with emulsion PVC as seed

Vinyl chloride was polymerized at 59–92% of saturation pressure in a water-suspended system at 45–65°C with an emulsion poly(vinyl chloride) (PVC) latex as a seed. A water-soluble initiator was used in various concentrations. The monomer was continuously charged as vapor from a storage vessel kept at lower temperature. Characterization included determination of molecular-weight distribution and degree of long-chain branching by gel permeation chromatography (GPC) and viscometry, thermal dehydrochlorination, and microscopy. The polymerization rate decreases with decreasing pressure but is reasonable even at the lowest pressure. The molecular weight decreases with decreasing pressure and increasing initiator concentration and also with increasing polymerization temperature, if the initiator concentrations are chosen to give a constant initiator radical concentration. The degree of long-chain branching increases with increasing initiator concentration and decreasing monomer pressure but is unaffected by the polymerization temperature, if the initiator radical concentration is kept constant. The thermal stability decreases with decreasing M _n, while the degree of long-chain branching has only a minor influence. The most important factor in the system influencing the molecular parameter is the monomer accessibility.     

Polymerization of diethylene glycol bis(allyl carbonate) by means of di-sec-butyl peroxydicarbonate

The initial stages of the free radical polymerization of diethylene glycol bis(allyl carbonate) at temperatures of 35–65°C have been studied. The polymer is unsaturated and cyclization to give a 16-membered ring occurs only to a small extent. The kinetic order with respect to the initiator, di-sec-butyl peroxydicarbonate, has an average value of 0.79; the order increases slightly with peroxydicarbonate concentration over the range 0.018–0.22M. The molecular weight of the polymer isolated after 3% polymerization is close to 19,000. It shows no significant dependence on initiator concentration or on temperature. The dominant feature of the bulk polymerization, as in free radical polymerization of the other allyl and diallyl monomers, is degradative chain transfer in which the growing polymer radical abstracts a hydrogen atom from a monomer unit to give a relatively unreactive allylic radical. The dependence of rate on initiator concentration is rationalized if some of these allylic radicals are able to reinitiate polymerization. The transfer constant to monomer is 0.014 at 50°C, assuming that the main termination step involves mutual termination of allylic radicals. Carbon tetrachloride is an active transfer agent with a transfer constant of 0.20 ± 0.04 at 50°C. Toluene, which is less active, has a transfer constant of 0.0064 at 50°C and also retards the polymerization. Some kinetic studies have been made with other initiators, including di-2-methyl-pentanoyl peroxide which initiates polymerization at temperatures as low as 13°C.     

Photopolymerization initiated by charge-transfer complex. I. Photopolymerization of methylmethacrylate with the use of quinaldine-bromine and lutidine–bromine charge-transfer complexes as photoinitiator

Photopolymerization of MMA was carried out with quinaldine–bromine (QN–Br₂) and lutidine–bromine (LU–Br₂) charge-transfer complexes as initiators. The rate of polymerization R_p increased with rising monomer concentration and the monomer exponent was computed as unity. At first the rate of polymerization accelerated and then reduced as the initiator concentration was increased. The initiator exponent was 0.5. The reaction was carried out at three different temperatures and overall activation energy was calculated at 4.0 kcal/mol. The kinetic data and other evidence indicate that the overall polymerization takes place in a radical mechanism. A suitable mechanism is suggested.     

Radical polymerization of vinyl acetate with primary radical termination

Vinyl acetate was polymerized at high initiation rate with 2,2′-azobis(2,4-dimethyl valeronitrile) as initiator at 50°C. In this polymerization, the power dependence of polymerization rate on the initiation rate is smaller than at lower concentration of monomer. This dependence was kinetically analyzed at each given concentration of monomer. Average degree of polymerization of polymer formed depends on the concentration of initiator. This dependence was explained by considering chain and primary radical terminations and transfer to monomer of polymer radical, and the initiator efficiency (=0.503) was deduced. It was found that the chain termination is inversely proportional to solvent viscosity, but the primary radical termination is not inversely proportional to solvent viscosity. Further, the value of the primary radical termination rate constant (=1.4 × 10⁹l./mole-sec) was estimated.     

Photopolymerization of methyl methacrylate using tetrahydrofuran sulphur dioxide complex as photoinitiator

Photopolymerization of MMA in visible light was studied at 40 using THF-SO₂ complex as the photoinitiator. Initiator exponent was 0.19 and monomer exponent lay between 1.0 and 1.5, depending on thenature of solvent. Analysis of kinetic and other data indicate that the polymerization proceeds by a radical mechanism and termination is initiator dependent. Chain termination via degradative chain (initiator) transfer appears to be significant feature.     

Photopolymerization of methyl methacrylate using a combination of rhodamine 6G and benzoyl peroxide as photoinitiator in nonaqueous media

Photopolymerization of methyl methacrylate (MMA) in visible light was studied at 40°C using Rhodamine 6G—Benzoyl peroxide combination as photoinitiator. The photopolymerization proceeds by a free radical mechanism and the radical generation process occurs by an initial complexation reaction between the initiator components. Kinetic data indicated a lower-order dependence of R_p on initiator concentrations (initiator exponent < 0.5). Initiator-dependent chain termination was significant along with the bimolecular mode of chain termination.     

Polymerization of methyl methacrylate using isatoic anhydride–bromine donor–acceptor complex as the photoinitiator

Isatoic anhydride (IA) alone did not initiate photopolymerization of methyl metacrylate (MMA) at 40°C when exposed to visible light for about 180 min. But IA, when used in combination with bromine (Br₂) as the initiator, initiated the photopolymerization of MMA readily under the same conditions. This behavior was explained by the formation of a donor-acceptor type of complex between IA and Br₂ in the presence of MMA. The polymerization was found to proceed via a free radical mechanism and the radical generation process was considered to follow an initial complexation reaction between the initiator components and monomer. The complex initiator showed nonideal kinetics for the present system (initiator exponent < 0.5) and was analyzed. The monomer exponents varied from 0.83 to 1.15 normally depending on the nature of solvent used. Initiator-dependent chain termination was significant as well as the bimolecular mode of chain termination. © 1993 John Wiley & Sons, Inc.     

Photopolymerization of methylmethacrylate using triethylamine-benzoylperoxide redox initiator system

Photopolymerization of MMA was studied kinetically at 35° using TEA-BZ₂O₂ redox system as initiator. The initiator exponent is 0.34 but the monomer exponent depends on the solvent. Solvents (acetonitrile, pyridine and bromobenzene) giving negative or fractional monomer exponent show a rate enhancing effect through actively influencing the initiation step; benzene and chloroform give first order dependence of rate on [monomer] and behave as normal (inert) diluents. Initiation of polymerization takes place through radicals generated by photodecomposition of TEA-BZ₂O₂ complex formed in situ, the radical generation step being solvent or monomer dependent. Kinetic non-idealities are interpreted in terms of significant initiator dependent termination via degradative chain transfer.     

Kinetic Investigation on the Photopolymerization of Methyl Methacrylate Using Iodine Trichloride as Initiator

The photopolymerization of MMA in visible light was studied at 45°C using IC1₃ as the photoinitiator. The initiator exponent was found to be 0.16 and the monomer exponent varied between 1.0 to 1.50, depending on the nature of the solvent. Analysis of the data revealed that the polymerization was induced by a free radical mechanism. Nonideality of the kinetics was explained on the basis of 1) Monomer-dependent chain initiation and 2) Initiator-dependent chain termination via degradative initiator transfer.     

Photopolymerization of methyl methacrylate and some other vinyl monomers with the use of chlorine as photoinitiator

Low concentrations (0.001–0.03M) of chlorine easily induce photopolymerization of MMA at 40°C. Kinetic data indicate that polymerization follows a radical mechanism involving complexation of monomer by the initiator and initiation takes place through radical generation during photodecomposition of the initiator-monomer complex. Termination appears to take place bimolecularly. The k_p²/k_t value for MMA polymerization at 40°C was found to be 0.83 × 10^?2. Rates of chlorine-initiated photopolymerization were found to decrease in the order MMA, EMA ? VA, Sty > MA.     

Studies on the kinetics of ceric–thiourea-initiated aqueous polymerization of methyl methacrylate. I. Mechanistic features in moderately acid solution

The kinetics of the aqueous polymerization of methyl methacrylate by a ceric-thiourea initiator system in moderately acid solution (pH 2.15) was studied. The rate of polymerization was proportional to 0.41 power of ceric concentration, 0.32 power of thiourea concentration, and 1.18 power of monomer concentration. The degree of polymerization was smaller than expected from the rate of polymerization. Initiation efficiency was less than one. There was no evidence of any ceric ion termination in the concentration range of 2.50 × 10^?4–2.00 × 10^?3M studied. The results are explained in terms of partial primary radical termination; the principal mode of termination, however, was bimolecular.