Response surface optimisation applied to a headspace-solid phase microextraction-gas chromatography-mass spectrometry method for the analysis of volatile organic compounds in water matrices

A new method for the simultaneous determination of 12 volatile organic compounds (trans-1,2-dichloroethene, 1,1,1-trichloroethane, benzene, 1,2-dichloroethane, trichloroethene, toluene, 1,1,2-trichloroethane, tetrachloroethene, ethylbenzene, m-, p-, o-xylene) in water samples by headspace solid phase microextraction (HS–SPME)–gas chromatography mass spectrometry (GC–MS) was described, using a 100?µm PDMS (polydimethylsiloxane) coated fibre. The response surface methodology was used to optimise the effect of the extraction time and temperature, as well as the influence of the salt addition in the extraction process. Optimal conditions were extraction time and temperature of 30?min and ?20°C, respectively, and NaCl concentration of 4?mol?L^?1. The detection limits were in the range of 1.1?×?10^?3–2.3?µg?L^?1 for the 12 volatile organic compounds (VOCs). Global uncertainties were in the range of 4–68%, when concentrations decrease from 250?µg?L^?1 down to the limits of quantification. The method proved adequate to detect VOCs in six river samples.     

Sampling and analysis of volatile organics emitted from wastewater treatment plant and drain system of an industrial science park

Volatile organic compounds (VOCs) were monitored in the different sections of a wastewater treatment plant (WWTP), the outlet of both the WWTP and rainfall water, and the downstream of the WWTP joining the river in the area or vicinity of an industrial science park located in Hsinchu, Taiwan. Levels of VOCs were determined by collecting air samples over several sampling points and analyzed using gas chromatography. Among VOCs identified in the drainage and effluent system in each season, acetone, isopropanol (IPA) and dimethyl sulfide (DMS) were the major emission species and maximum concentrations were 400.4, 22.8 and 641.2 ppbv, respectively. The ambient air and wastewater sample analysis from neighboring wastewater streams identified pollutants being discharged from unaccounted sources other than the industrial park. According to the 24 h semi-continuous monitoring data (27/7/2002-29/7/2002), the total VOC concentration was an average of 93 ppbv (acetone contributed ∼78%) with a dramatic variation during the day and night. The emission rate of measured VOCs estimated using fixed box model projected an average of 2-4 μg m⁻² h⁻¹) during the day and 9-17 μg m⁻² h⁻¹ during the night. In addition, the isopleth maps show that the acetone and DMS emissions influence adversely the nearby residential area located at less than 100 m downwind from the plant. Eventually, based on this study, an on-line monitoring and alerting system could be built for a long-term performance, and with regular information on the varying pollutants over time construction of a green strategy and creation of a sustainable environment can be achieved.     

Volatile organic compounds in an urban environment: a comparison among Belgium,Vietnam and Ethiopia

The effects of urban and indoor air pollution on human health are a major environmental concern for all, but not much has been researched in the developing world. Specifically, quantitative data on the occurrence of volatile organic compounds (VOCs) – main contributors to air pollution – in Asia and Africa are scarce compared to the availability of data in the developed world. This paper presents one of the first studies focusing on the analysis and occurrence of VOCs in Vietnam and Ethiopia, which constitutes part of the novelty of this work. A spectrum of 34 VOCs was measured at eight different urban sites in Ghent (Belgium), Hanoi (Vietnam), Jimma and Addis Ababa (Ethiopia) during three sampling campaigns from September 2008 to September 2010. Sampling was done in an active way by means of sorbent tubes filled with Tenax TA. The analysis was done by TD-GC-MS using internal standard calibration. Data were interpreted and compared in terms of (i) individual, subgroup and total VOCs concentration (TVOCs), (ii) indoor-to-outdoor (I/O) concentration ratios, (iii) source identification by diagnostic ratio and/or correlation coefficients, and (iv) ozone formation potential (OFP) at outdoor sites based on up-to-date maximum incremental reactivity (MIR). I/O concentration ratios varied between 0.2 and 30, with big differences noticed with respect to the type of VOC(s) considered and the type of outdoor sampling location. The highest TVOC concentrations were measured in street samples with maximum values of 54?µg/m³ in Ghent, 507?µg/m³ in Hanoi and 318?µg/m³ in Addis Ababa illustrating the large difference in ambient air quality levels. This is also reflected in the arithmetic mean OFP values (µg/m³) of 82, 1308 and 596 in Ghent, Hanoi and Addis Ababa, respectively. Results of this study could be helpful to support formulation of national policy with regard to ambient air quality.     

Determination of volatile organic compounds in urban and industrial air from Tarragona by thermal desorption and gas chromatography-mass spectrometry

This study describes the optimisation of an analytical method to determine 54 volatile organic compounds (VOCs) in air samples by active collection on multisorbent tubes, followed by thermal desorption and gas chromatography-mass spectrometry. Two multisorbent beds, Carbograph 1/Carboxen 1000 and Tenax/Carbograph 1TD, were tested. The latter gave better results, mainly in terms of the peaks that appeared in blank chromatograms. Temperatures, times and flow desorption were optimised. Recoveries were higher than 98.9%, except methylene dichloride, for which the recovery was 74.9%. The method's detection limits were between 0.01 and 1.25 μg m⁻³ for a volume sample of 1200 ml, and the repeatability on analysis of 100 ng of VOCs, expressed as relative standard deviation for n = 3, was lower than 4% for all compounds. Urban and industrial air samples from the Tarragona region were analysed. Benzene, toluene, ethylbenzene and xylenes (BTEX) were found to be the most abundant VOCs in urban air. Total VOCs in urban samples ranged between 18 and 307 μg m⁻³. Methylene chloride, 1,4-dichlorobenzene, chloroform and styrene were the most abundant VOCs in industrial samples, and total VOCs ranged between 19 and 85 μg m⁻³.     

Volatile organic compounds in landfill odorant emissions on the island of Mallorca

This study provides data on the occurrence of volatile organic compounds (VOCs) in the biogas emission from a landfill located on the island of Mallorca (Balearic Islands, Spain), where 200,000 tonnes of urban solid wastes are dumped every year. Three different sampling cells, of differing waste ageing were investigated in August 2008, during the main tourist season and the warmest possible weather conditions. Samples were collected in Nalophan? bags according to the standard European method EN 13725 followed by VOCs adsorption onto Carboxen 1000? and Tenax TA? materials prior to thermal desorption and analysis by GC-MS. In total 42 VOCs were analysed, using external standards, out of which 36 were positively identified. Detected VOCs in µg?m^?3 were alkanes (19–62), aldehydes (65–98), ketones (78–129), alcohols (67–78), esters (25–33), BTEX (83–106), halogenated compounds (16–39), terpens (1.4–2.4) and reduced sulphur compounds (2.6–4.2), showing different concentrations on each one of the three cells. Emitted VOCs showed some similarities with other previous studies from China and Turkey, while large differences to an Italian study. The benzene-to-toluene ratio (B:T) showed values in the range of 0.13 to 0.20 characteristic of biogas. H₂S and NH₃ gases emitted by the landfill were measured in-situ utilising Dräger? Tubes for Short-Term-Measurements, showing concentration levels of ≤800?µg?m^?3 and <300?µg?m^?3, respectively, which is higher than the determined VOCs in accordance with previous studies. Samples were examined with dynamic olfactometry following standard European method EN 13725, to determine a potential statistical linear correlation between odour and VOC concentrations. Such correlations were not observed probably owing to the large number of compounds emitted from garbage which are not quantified, yet causing positive results in olfactometry.     

Monitoring of di-(2-ethylhexyl)phthalate,nonylphenol, nonylphenol ethoxylates,and polychlorinated biphenyls in anaerobic and aerobic sewage sludge by gas chromatography–mass spectrometry

The occurrence of di-(2-ethyhexyl)phthalate (DEHP), nonylphenol and nonyphenol mono- and diethoxylates (NPEs) and seven polychlorinated biphenyl (PCB) congeners in different types of sludge samples is reported. The analysis of these compounds was carried out by sonication-assisted extraction and analytical determination by gas chromatography coupled with a mass spectrometry detector, following a previously described method. The applicability of the method was tested by monitoring the organic pollutants in primary, secondary, mixed, and digested-dehydrated sludge samples from two wastewater treatment plants (WWTPs) based on aerobic and on anaerobic biological stabilization. The occurrence of these compounds in sewage sludge and the influence of sludge stabilization process on the further farmland application of the sludge were evaluated. DEHP and NPEs were detected in all analysed sludge samples from both WWTPs at concentration levels in the range of 22.3–601?mg?kg^?1 and 136–2357?mg?kg^?1 dm (dry matter), respectively. PCBs were detected in all types of sludge analysed from the anaerobic WWTP but was not detected in any sludge sample from the aerobic WWTP. Concentration levels of the sum of the seven PCBs congeners were up to 1.5?mg?kg^?1 dm. The concentration of DEHP, sum of NPEs, and sum of the seven PCB congeners were higher than the limits fixed in the third draft of the future Sludge Directive for land application of sludge in the 67%, 100%, and 11% of samples from the anaerobic WWTP and in the 83%, 92%, and 0% of samples from the aerobic WWTP, respectively.     

Determination of 19 volatile organic compounds in wastewater effluents from different treatments by purge and trap followed by gas-chromatography coupled to mass spectrometry

A rapid and simple methodology based on purge and trap with gas-chromatography coupled to triple quadrupole mass spectrometry has been developed for the analysis of 19 volatile organic compounds (VOCs) in wastewater (WW) effluents from four different treatments. The determination was carried out in the raw WW effluents, which were not submitted to any pre-treatment (e.g., filtration). A matrix effect study was also performed, concluding that solvent calibration was adequate to quantify VOCs in WW effluent samples containing a variety of suspended particulate matter. Adequate validation parameters were obtained with recovery values in the range 73–124% and precision values lower than 24%. Limits of quantification were established at 0.1 μg L^-1 for all VOCs. The proposed method was applied to the analysis of WW samples, detecting chloroform and toluene at concentrations ranging from 0.1 to 4.80 μg L^-1.     

Development of a method for the monitoring of odor‐causing compounds in atmospheres surrounding wastewater treatment plants

This study describes the development of an analytical method based on active collection in a multisorbent Tenax TA/Carbograph 1TD tube, followed by thermal desorption and GC‐MS for the determination of 16 volatile organic compounds in air samples. The analyzed compounds include ozone precursors and odor‐causing compounds belonging to different chemical families (sulfur‐ and nitrogen‐containing compounds, aldehydes, and terpenes). Two types of sorbents were tested and desorption conditions (temperature, time, and sampling, and desorption flow) were evaluated. External calibration was carried out using the multisorbent bed. Method detection limits in the range 0.2–2.0 μg m^?3 for 1 L samples were obtained. The method was applied for determining the target compounds in air samples from two different wastewater treatment plants. Most compounds were detected and toluene, limonene, and nonanal were found in particularly high concentrations with maximum values of 438, 233, and 382 μg m^?3, respectively.     

Rapid Simultaneous Determination of Volatile Organic Compounds in Mattress Fabric by Headspace–Gas Chromatography–Mass Spectrometry

An analytical method for simultaneously determining 32 volatile organic compounds in mattress fabrics based on static headspace coupled to gas chromatography and mass spectrometry detection was established. Samples were cut into 5?×?5?mm small pieces and placed in a 20?mL headspace vial at 90° for 30?min. To achieve the optimum conditions for the analysis, several parameters including the heating temperature, heating time, sample weight, and injection time were investigated. The results demonstrated that the most important parameter influencing the sensitivity of the analysis was the heating temperature. The optimum method showed good linearities with correlation coefficients ranged from 0.9944 to 0.9998. The limits of detection and quantification for the target compounds were in the ranges of 0.004–0.032 and 0.013–0.099?µg/?g, respectively. The method was successfully applied to determine the volatile organic compounds in six categories of mattress fabrics. The results showed that some volatile organic compounds were found, such as naphthalene, hexadecane, and 1,4-diisopropylbenzene. Moreover, the concentrations of 32 volatile organic compounds decreased following the order of jute, terylene, polyester, velboa, nylon, and cotton samples in the study. These results indicated that the method is fast, accurate, and successful for determining volatile organic compounds in mattress fabrics.     

热脱附-气相色谱-质谱法测定环境空气中67种挥发性有机物

采用热脱附-气相色谱-质谱法,建立了同时分析环境空气中67种挥发性有机物的分析方法。对比了5种不同填充材料不锈钢吸附管对78种挥发性有机物的吸附能力。填充材料为Tenax TA和Carbograph 1TD的混合填料吸附管对分析物的捕集效果最好,在30 mL/min高纯He气持续吹脱45 min的情况下,未发生穿透（即穿透率小于10%）的化合物达67种,分析物的种类包括芳香烃、脂肪烃、卤代烃和含氧挥发性有机物等。优化了使用该吸附管测定67种目标物时的热脱附条件。在5~100 ng范围内,目标化合物的色谱响应值与其量间具有良好的线性关系,其相关系数（r）均在1.0000~0.9977之间。方法检出限为0.3~2.4 ng,以采样体积1 L计算,检出限为0.3~2.4 μg/m³。加标量为20 ng时,7次重复实验目标化合物回收率均在81.6%~114.9%之间,目标化合物的相对标准偏差为1.2%~10.1%。采用该方法对某车厢内空气进行了检测,检出了包括酯类、卤代烷烃、卤代烯烃以及芳香族化合物在内的19种目标化合物,其范围为1.1~84.1 μg/m³。该方法准确、可靠、灵敏度高,实现了对环境空气中67种目标污染物的准确定量。     

Determination of volatile organic compounds in contaminated air using semipermeable membrane devices

Semipermeable membrane devices (SPMDs) were evaluated as passive samplers for the determination of 26 volatile organic compounds (VOCs) in contaminated air of occupational environments. A direct methodology based on the use of head-space-gas chromatography-mass spectrometry (HS-GC-MS) was developed for VOCs determinations in SPMDs, without any sample pre-treatment and avoiding the use of solvents. A desorption temperature of 150 °C for 10 min was sufficient for a sensitive VOCs determination providing limits of detection in the range of 15 ng SPMD⁻¹ for 21 of 26 studied compounds. Linear and equilibrium uptake models were established for each VOC from compound isotherms. Highly volatile compounds were slightly absorbed and moderately volatile compounds were strongly absorbed by SPMDs. This study is the first precedent of the use of SPMDs for the simultaneous sampling of a wide number of VOCs. The use of SPMDs is a simple and low cost alternative to ordinary sampling devices such as Radiello^® diffusive samplers or badge-type solid-phase supports.     

Analysis of volatile organic compounds in wastewater during various stages of treatment for high-tech industries

Summary A protocol combining purge-and-trap (P&T) and solid-phase microextraction (SPME) was established for the analysis of volatile organic compounds (VOCs) in the wastewater plant of high-tech industries. Over 60 VOCs could be analyzed by P&T coupled to gas chromatography/mass spectrometry (P&T-GC-MS). Four polar VOCs commonly used in the high-tech industries were determined by SPME coupled to gas chromatography/flame ionization detection (SPME-GC-FID). The limits of detection for the analytes were less than 1.1 μg L⁻¹ with P&T-GC-MS, and between 1.5 and 12.5 μg L⁻¹ with SPME-GC-FID. Satisfactory recoveries (83% to 130%) were obtained. Real samples were analyzed from a wastewater treatment plant during various stages of treatment. The major pollutant in the wastewater influent was found to be acetone (>4 ppm).     

Optical waveguide sensor of volatile organic compounds based on PTA thin film

In this study, a sensitive optical waveguide (OWG) sensor for the detection and identification of volatile organic compounds (VOCs) was reported. The sensing membrane is constructed by immobilization of peroxopolytungsten acid (PTA) thin film over a single-mode potassium ion (K⁺) exchanged glass OWG by spin-coating method. A laser beam was coupled into and out of the glass optical waveguide using prism couplers, and dry air functioned as a carrier gas. The sensor was tested for various volatile organic compounds (VOCs), and it showed higher response to the chlorobenzene gas compared to other VOCs. Therefore, we used the OWG sensor to detect chlorobenzene gas as a typical example of VOCs. The sensor exhibits a linear response to chlorobenzene gas in the range of 0.4-1000 ppm with rapid response and good reversibility. The constructed sensor is easy to fabricate and it has some unique qualities which can be characterized as inexpensive, sensitive, and reusable.     

Investigation on Distribution and Risk Assessment of Volatile Organic Compounds in Surface Water,Sediment, and Soil in a Chemical Industrial Park and Adjacent Area

The occurrences, distributions, and risks of 55 target volatile organic compounds (VOCs) in water, sediment, sludge, and soil samples taken from a chemical industrial park and the adjacent area were investigated in this study. The Σ₅₅-VOCs concentrations in the water, sediment, sludge, and soil samples were 1.22–5449.21 μg L⁻¹, ND–52.20 ng g⁻¹, 21.53 ng g⁻¹, and ND–11.58 ng g⁻¹, respectively. The main products in this park are medicines, pesticides, and novel materials. As for the species of VOCs, aromatic hydrocarbons were the dominant VOCs in the soil samples, whereas halogenated aliphatic hydrocarbons were the dominant VOCs in the water samples. The VOCs concentrations in water samples collected at different locations varied by 1–3 orders of magnitude, and the average concentration in river water inside the park was obviously higher than that in river water outside the park. However, the risk quotients for most of the VOCs indicated a low risk to the relevant, sensitive aquatic organisms in the river water. The average VOCs concentration in soil from the park was slightly higher than that from the adjacent area. This result showed that the chemical industrial park had a limited impact on the surrounding soil, while the use of pesticides, incomplete combustion of coal and biomass, and automobile exhaust emissions are all potential sources of the VOCs in the environmental soil. The results of this study could be used to evaluate the effects of VOCs emitted from chemical production and transportation in the park on the surrounding environment.     

Simultaneous analysis of 23 priority volatile compounds in water by solid-phase microextraction–gas chromatography–mass spectrometry and estimation of the method's uncertainty

Most water contaminations with volatile organic compounds (VOCs) are traceable to leaking underground fuel reservoirs, solvent storage vessels, agricultural practices, industrial residues, and deficient wastewater treatment and disposal. In order to perform effective monitoring of such organic micropollutants in a straightforward manner, a multiresidue method for the determination of 23 VOCs (trihalomethanes (THMs), BTEX and chlorinated solvents) in water has been developed using solid-phase microextraction (SPME) and capillary gas chromatography–mass spectrometry (GC–MS). This group includes also methyl-tert-butyl ether, epichlorhydrine, and vinyl chloride which present additional analytical difficulties. Three different fibres were assayed: 7-µm polydimethylsiloxane (PDMS), 100-µm PDMS, and 75-µm Carboxen-PDMS, and the extraction conditions were optimized. The best results for the majority of the analytes and mainly for those with the lowest signals were obtained using the Carboxen-PDMS fibre after 15 min of extraction in the headspace mode at a room temperature of 20 ± 2°C. The analytical sensitivity, linearity, precision, accuracy, and uncertainties have been studied for method validation in agreement with the international standard ISO/IEC 17025:2005. The limits of detection achieved with the proposed method (0.06–0.17 µg L^?1) are adequate to determine the VOCs at the restrictive levels established by the European legislation. This was a decisive achievement to enable the analysis of all VOCs listed under the drinking-water directive in a single assay. The method exhibits performance capabilities suitable for routine analysis of VOCs in drinking-water by quality-control laboratories as enforced by EU Directives. The method is currently being used for this purpose, and participation in proficiency tests was assessed, with encouraging results.     

Identification and characterization of polycyclic aromatic hydrocarbons in coking wastewater sludge

GC‐MS analysis was performed on the coking sludge from a coking wastewater treatment plant (WWTP) to allow detailed chemical characterization of polycyclic aromatic hydrocarbons (PAHs). The identification and characterization of the isomers of PAHs was based on a positive match of mass spectral data of their isomers with mass spectra databases or based on a comparison of electron impact ionization mass spectra and retention times of target compounds with those reference compounds. In total, 160 PAH compounds including numerous N‐, O‐, S‐, OH‐, and Cl‐containing derivatives were positively identified for the first time. Quantitative analysis of target compounds was performed in the selected ion‐monitoring mode using the internal standard method. The total concentrations of selected compounds in the coking sludge samples from the anaerobic tank, aerobic tank, hydrolytic tank, and secondary clarifier of the WWTP ranged from 1690 ± 585 to 6690 ± 522 mg/kg, which were much higher than those in other industrial and municipal sludges. PAHs with four and five rings were found to be the dominant compounds, and diagnostic ratios of these compounds suggested that they had the characteristics of coal combustion and pyrolysis.     

Determination of cephalosporin antibiotics in water samples by optimised solid phase extraction and high performance liquid chromatography with ultraviolet detector

A reliable and robust analytical method based on solid phase extraction (SPE) and high performance liquid chromatography (HPLC) with ultraviolet (UV) detector was developed for the simultaneous determination of five cephalosporin antibiotics (Ceftazidime, Cefradine, Cefaclor, Cefotaxime and Cefoperazone) in various water samples. Under optimised conditions, it was applicable to preconcentrate up to 500?ml of water samples in the OASIS HLB cartridges with reasonable recoveries for all the cephalosporin antibiotics tested. Recoveries were as follows: deionised water, tap water and groundwater, between 84.2 and 98.9%; surface water, between 71.2 and 81.0%; influent and effluent of wastewater treatment plant (WWTP), between 56.9 and 72.1%. The method detection limits (MDLs) for different water samples were in the range of 26 to 59?ng?l^?1. Real water samples were analysed using the proposed approach to demonstrate the applicability and validation. Negative results were obtained for the tap water and groundwater. However, all the selected cephalosporin antibiotics were identified in the influent and effluent of a local WWTP at ng?l^?1–µg?l^?1 level. In addition, Ceftazidime was found in surface water with a concentration of 0.75–2.60?µg?l^?1. The results indicate that the ‘pseudo-persistent’ contamination of cephalosporin antibiotics in the water environment could not be neglected.     

Rotating Biological Contactor Reactor with Biofilm Promoting Mats for Treatment of Benzene and Xylene Containing Wastewater

A novel rotating biological contactor (RBC) bioreactor immobilized with microorganisms was designed to remove volatile organic compounds (VOC), such as benzene and xylene from emissions, and its performance was investigated. Gas-phase VOCs stripped by air injection were 98?% removed in the RBC when the superficial air flow rate was 375?ml/h (1,193 and 1,226?mg/l of benzene and xylene, respectively). The maximum removal rate was observed to be 1,007 and 1,872?mg/m³/day for benzene and xylene, respectively. The concentration profile of benzene and xylene along the RBC was dependent on the air flow rate and the degree of microbial adaptation. Air flow rate and residence time were found to be the most important operational parameters for the RBC reactor. By manipulating these operational parameters, the removal efficiency and capacity of the bioreactor could be enhanced. The kinetic constant K _s demonstrated a linear relationship that indicated the maximum removal of benzene and xylene in RBC reactor. The phylogenic profile shows the presence of bacterium like Pseudomonas sp., Bacillus sp., and Enterococcus sp., which belonged to the phylum Firmicutes, and Proteobacteria that were responsible for the 98?% organic removal in the RBC.     

Novel sample preparation technique with needle-type micro-extraction device for volatile organic compounds in indoor air samples

A novel needle-type sample preparation device was developed for the effective preconcentration of volatile organic compounds (VOCs) in indoor air before gas chromatography–mass spectrometry (GC–MS) analysis. To develop a device for extracting a wide range of VOCs typically found in indoor air, several types of particulate sorbents were tested as the extraction medium in the needle-type extraction device. To determine the content of these VOCs, air samples were collected for 30 min with the packed sorbent(s) in the extraction needle, and the extracted VOCs were thermally desorbed in a GC injection port by the direct insertion of the needle. A double-bed sorbent consisting of a needle packed with divinylbenzene and activated carbon particles exhibited excellent extraction and desorption performance and adequate extraction capacity for all the investigated VOCs. The results also clearly demonstrated that the proposed sample preparation method is a more rapid, simpler extraction/desorption technique than traditional sample preparation methods.     

Determination of chlorinated volatile organic compounds in water and municipal wastewater using headspace-solid phase microextraction-gas chromatography

The aim of this work was to develop a fast and simple analytical method for the determination of 14 chlorinated volatile organic compounds (VOCs) in water and wastewater samples. Headspace-solid-phase microextraction (HS-SPME) and gas chromatography (GC) were used for the determination of the VOCs. The extraction parameters were investigated in order to optimize the HS-SPME-GC method. The quality parameters of the method were also investigated.