Development and validation of a SPE-GC-MS method for the determination of pesticides in surface water

A method for analysis of 20 commonly used pesticides in surface water based on solid-phase extraction and gas chromatography-mass spectrometry was proposed. During method development the key parameters that can affect SPE extraction and determination such as selection of efficient SPE sorbent, pH of water sample, type and volume of elution solvent, breakthrough volume and matrix effects were investigated. The method was validated using spring water spiked with appropriate concentration of pesticides. The obtained correlation coefficients were in range 0.9972–1.000, limits of detection (LOD) were 0.001–0.5?µg?L^?1 and the limits of quantification (LOQ) were 0.005–1?µg?L^?1 depending on a pesticide. Much higher LOD (20?µg?L^?1) and LOQ (50?µg?L^?1) values were obtained for bentazone. The influence of matrix was assessed using real water samples spiked with appropriate concentration of pesticide standards solution. Both signal enhancement and suppression were observed, depending on a pesticide, therefore standard addition method was used for pesticides determination. The developed method was applied on real water samples taken in close vicinity of agricultural fields. Many of the targeted pesticides were found in the samples and the results are presented in this article.     

Simultaneous extraction and determination of pharmaceuticals and personal care products (PPCPs) in river water and sewage by solid-phase extraction and liquid chromatography-tandem mass spectrometry

This study features the simultaneous extraction and quantification of 18 pharmaceuticals and personal care products (PPCPs). This is a pioneering method for the quantification of acetaminophen, sulfamethoxazole, diclofenac, atenolol, metoprolol, diethyltoluamide and oxybenzone in atmospheric pressure chemical ionisation mode. The method was validated for high repeatability and reproducibility with relative standard deviations less than 10%. Instrument quantification limits for PPCPs were within the range of 0.05–1.0 µg L^?1, and the method quantification limits (MQLs) for ultrapure water were within the range of 0.3–15 ng L^?1. All samples were extracted using Oasis© hydrophilic–lipophilic balanced cartridges with optimised sample size and extraction conditions. Good accuracy was demonstrated, with solid-phase extraction recoveries above 80% for most PPCPs. In environmental matrices, the MQLs for river water, sewage treatment plant (STP) effluent and STP influent were 4–25, 10–153 and 38–386.5, respectively. The method was successfully applied to investigate occurrences of persistent PPCPs in Malaysian river and sewage samples.     

Determination of Selenium by Single-Drop Microextraction and Diffuse Reflectance Infrared Spectroscopy

A simple and convenient assay based on single-drop microextraction with infrared spectroscopy is reported for the determination of selenium. The extraction conditions were carefully optimized and selenium was preconcentrated through single-drop microextraction in 1,2-dichloroethane containing N-hydroxy-N-phenyl-N′-(o-tolyl) benzimidamide. The method is selective and almost all common ions including molybdenum(VI), chromium(VI), and tungsten(VI) did not interfere with the isolation protocol. The selenite band at 875?±?2?cm^?1, which is assigned to the asymmetric vibrational stretch (υ₃), was used for the quantification of selenium. Low limits of detection and quantification of 2.0 and 6.6?µg?L^?1 demonstrate the sensitivity of the method. Good precision was evaluated by the standard deviation (2.0?µg?L^?1) and relative standard deviation (0.5%) for 8?µg?L^?1 was achieved for 10 measurements. The method was used to analyze human blood, urine, and water for selenium.     

Development of carbon paste electrode modified with cadmium ion-imprinted polymer for selective voltammetric determination of Cd2+

A simple and fast voltammetric method based on a new electrode composed of carbon paste electrode/bifunctional hybrid ion imprinted polymer (CPE/IIP) was developed for the quantification of Cd²⁺ in water samples. The voltammetric measurements by Differential Pulse Voltammetry were performed by using CPE containing 11.0 mg of IIP under phosphate buffer solution at concentration 0.1 mol L^?1 and pH 6.5. The electrochemical method was carried out by Cd²⁺ preconcentration at ?1.2 V during 210 s, followed by anodic stripping. The performance of IIP towards Cd²⁺ determination was evaluated by comparison to non-imprinted polymer, whose detectability of IIP was much higher (45%). The sensitivity of the sensor was found to be 0.0105 µA/µg L^?1. The limits of detection and limits of quantification were found to be 4.95 μg L^?1 and 16.4 μg L^?1, respectively. The developed method was successfully applied to Cd²⁺ determination in mineral, tap and lake water samples, whose results are in agreement with thermospray flame furnace atomic absorption spectrometry (TS-FF-AAS) used as reference analytical technique. According to achieved results, the developed method can be used for routine analysis of quality control of water samples from different sources.     

Cloud point extraction for the determination of cadmium and lead employing sequential multi-element flame atomic absorption spectrometry

A cloud point extraction procedure for pre-concentration and determination of cadmium and lead in drinking water using sequential multi-element flame atomic absorption spectrometry is described. 4-(2-thiazolylazo)-orcinol (TAO) has been used as complexing agent and the micellar phase was obtained using the non-ionic surfactant octylphenoxypolyethoxyethanol (Triton X-114) and centrifugation. The conditions for reaction and extraction (surfactant concentration, reagent concentration, effect of incubation time, etc) were studied and the analytical characteristics of the method were determined. The method allows the determination of cadmium and lead with quantification limits of 0.30?µg?L^?1 and 2.6?µg?L^?1, respectively. A precision expressed as relative standard deviation (RSD, n?=?10) of 2.3% and 2.6% has been obtained for cadmium concentrations of 10?µg?L^?1 and 30?µg?L^?1, respectively, and RSD of 1.3% and 1.7% for lead concentrations of 10?µg?L^?1 and 30?µg?L^?1, respectively. The accuracy was confirmed by analysis of a natural water certified reference material. The method has been applied for the determination of cadmium and lead in drinking water samples collected in the cities of Ilhéus and Itabuna, Brazil. Recovery tests have also been performed for some samples, and results varied from 96 to 105% for cadmium and 97 to 106% for lead. The cadmium and lead concentrations found in these samples were always lower than the permissible maximum levels stipulated by World Health Organization and the Brazilian Government.     

A novel,simple and robust method for the analysis of sulfonamides in fish farming water samples using column switching liquid chromatography

A novel method for the online extraction and preconcentration of four sulfonamides was developed using column switching liquid chromatography. Sulfadiazine, sulfathiazole, sulfamethoxypyridazine and sulfamethoxazole were analysed in water samples and preconcentrated in a C18 guard column. Suitable validation parameters were obtained, such as precision, accuracy and relative recovery, in accordance with the validation guidelines of the Food and Drug Administration. Low limits of detection (0.05–0.09 µg L^?1) and quantification (0.30 µg L^?1, for all of them) were obtained. The quadratic polynomial model was used to adjust the calibration data, and the coefficients of determination were higher than 0.999 for all the analytes. The method was shown to be robust to the assayed parameters according to Youden’s test. The proposed method was successfully used to determine sulfonamides in 11 different fish farming water samples, in which sulfadiazine (0.732 µg L^?1), sulfamethoxazole (0.531 µg L^?1), sulfathiazole (0.546–1.856 µg L^?1) and sulfamethoxypyridazine (0.369–1.509 µg L^?1) were found.     

Continuous sonoassisted digestion coupled to flow injection minicolumn separation for the determination of total and labile Cu and Fe in fresh waters by flame atomic absorption spectrometry

An automatic on-line system is developed for the trace determination of copper and iron species in fresh waters by flame atomic absorption spectrometry using only 5 and 2?mL of sample, for copper and iron determination, respectively. This system, which includes a home-made minicolumn of commercially available resin containing aminomethylphosphonic acid functional groups (Chelite P), comprises two operational modes. The first, used for the determination of the dissolved labile fraction (free copper and iron ions and their weak complexes) is based on the elution of this fraction from a minicolumn containing the chelating resin loaded in-situ with the sample. The second mode is used for the determination of total trace copper and iron concentrations. This last mode is based on the retention/preconcentration of total metals on the Chelite P resin after on-line sonoassisted digestion of water samples acidified with nitric acid (0.5?mol?L^?1 final concentration) to break down metal organic complexes present in fresh waters as river waters. The figures of merit for copper and iron determination in both fractions are given and the obtained values are discussed. The analytical method was characterized and the limit of detection and limit of quantification for the two metals were 0.5 and 1.6?µg?L^?1 for Cu and 2.3 and 6.1?µg?L^?1 for Fe, respectively. The repeatability, expressed as relative standard deviation, was in the range 1.0–2.1%. The speciation scheme was applied to the analysis of river surface water samples collected in Galicia (Northwest, Spain).     

HS-SPME-GC-MS analysis of antioxidant degradation products migrating to drinking water from PE materials and PEX pipes

Polyethylene (PE) and cross-linked polyethylene (PEX) pipes are frequently used in water supply systems. Such pipes contain added antioxidants with phenolic structures, e.g. Irgafos 168, Irganox 1010 and 1076, in order to improve durability. However, phenol, ketone and quinone antioxidant degradation products may leach and enter drinking water. The aim of this investigation was to develop a method for measuring these degradation products with a performance meeting the drinking water quality criteria of 20?µg?L^?1. Using headspace solid phase microextraction coupled to a gas chromatograph with a mass spectrometer, a method was established revealing limits of detection and quantification less than 0.4 and 1?µg?L^?1 respectively. The method was applied to migration experiments for two PEX pipes and one PE material, quantifying the release of two degradation products. Highest concentrations were observed for 2,6-di-tert-butyl-p-benzoquinone which in one of the two pipes was found in concentrations of 18–57?µg?L^?1 in each of eight consecutive release experiments.     

Trace determination of malachite green in water samples using dispersive liquid–liquid microextraction coupled with high-performance liquid chromatography-diode array detection

A simple and reliable method has been developed for the rapid analysis of trace levels of malachite green from water samples using dispersive liquid–liquid microextraction and high-performance liquid chromatography-diode array detection. Factors relevant to the microextraction efficiency, such as the type and volume of extraction solvent, nature and volume of the disperser solvent, the effect of salt, sample solution temperature and the extraction time were investigated and optimised. Under the optimal conditions the linear dynamic range of malachite green was from 0.2 to 100.0?µg?L^?1 with a correlation coefficient of 0.9962. The detection limit and limit of quantification were 0.1?µg?L^?1 and 0.3?µg?L^?1, respectively. The relative standard deviation (RSD) was less than 2.6% (n?=?5) and the recoveries of malachite green (5.0?µg?L^?1) from water samples were in the range of 99.2?±?1.7%. Finally the proposed method was successfully applied for the analysis of malachite green from fish farming water samples.     

Highly sensitive ion preconcentration method based on flow sorbent extraction using multiwall carbon nanotubes

In this work a solid phase on-line uranium ion preconcentration system coupled with spectrophotometry has been developed. The method is based on uranyl ion preconcentration at pH 3.75 onto multiwall carbon nanotubes treated with HNO₃. After preconcentration, the uranyl ions are eluted with 0.32?mol?L^?1HCl followed by reaction with 3,6-bis[(2-arsonophenyl)-azo]-4,5-dihydroxy-2,7-naphthalendisulfonic acid 0.08%[w/v] (Arsenazo III), which had maximum monitored absorbance of 650?nm. Effects of the pertinent experimental parameters on the system were investigated by means of 2^6?2 fractional factorial design, while optimization was carried out using the Doehlert matrix. Under optimized conditions, detection and quantification limits were found to be 0.21 and 0.7?µg?L^?1, respectively. The analytical curve ranged from 5 to 150?µg?L^?1 (r?=?0.998), while the relative standard deviations (RSD) were 3.27 and 2.56% for the respective uranium concentrations of 10 and 100?µg?L^?1 (n?=?10). The features obtained for the on-line preconcentration system were: preconcentration factor of 228, concentration efficiency of 57?min^?1, consumption index of 0.13?mL and sample throughput of 15?h^?1. In order to assess the accuracy of the proposed method, addition and recovery studies were carried out on spring water samples from different sources and synthetic seawater with satisfactory results ranging from 94.85 up to 103.65%.     

Electrochemical Studies of Ochratoxin A Mycotoxin at Gold Electrodes Modified with Cysteamine Self‐Assembled Monolayers. Its Ultrasensitive Quantification in Red Wine Samples

The quantification of ochratoxin A is studied at cysteamine self‐assembled monolayer modified gold electrodes in red wine samples by square wave voltammetry. Detection and quantification limits of 0.004 µg L^?1 and 0.012 µg L^?1, respectively, were determined. The recovery percentages were in the range from 146 % to 94.0 % at spiking levels ranging from 0.02 to 5 µg L^?1. The variation coefficients for within‐laboratory repeatability varied from 31.4 to 11.5 % for spiked level from 0.02 to 2.0 µg L^?1. The developed electrochemical method is efficient, reproducible, and ultrasensitive for the quantification of OTA in red wine samples.     

Simultaneous Quantification of Oroxylin A and Its Metabolite Oroxylin A-7-O-Glucuronide: Application to a Pharmacokinetic Study in Rat

A sensitive liquid chromatography?Celectrospray ionization?Ctandem mass spectrometry (LC?CESI?CMS?CMS) method was developed and validated for the quantification of cepharanthine (CEP) in beagle dog plasma. The chromatographic separation was performed on an Agilent-C18 column and the mobile phase was composed of methanol:water with 10 mM ammonium acetate (20:80, v/v). Detection was operated in the positive ion mode and the tandem mass spectrometer was tuned in the multiple reactions monitoring mode (MRM) to monitor m/z transitions 607 ?? 365 for CEP and 285 ?? 193 for the internal standard (IS) diazepam. This method exhibited a linear range of 5?C2,500 ng mL^?1. The precision (RSD%) and accuracy (RME%) of the assay were <8.7 and 2.4%, respectively. The limit of quantification was 5 ng mL^?1 and no significant matrix effect was observed. The validated method has been successfully applied to pharmacokinetic study of CEP in beagle dog.     

Characterization of Carbamate Pesticides in Natural Water from Cameroon

With the increased use of chemicals in agriculture for crop protection and improvement of yield, the contamination of water is currently a serious health concern. This study used solid-phase extraction with ultra-high-performance liquid chromatography–tandem mass spectrometry to evaluate the presence of 23 carbamate pesticides in waters from Cameroon. The separation was achieved in 5.5?min using a C₁₈ column (50?×?2.1?mm, 1.8?µm) with a mobile phase composed of water and methanol each containing 0.01% formic acid. The analytes were determined in positive multiple reaction monitoring mode. The recoveries for fortified water were from 75 to 99%, with relative standard deviations below 13%. The limits of detection ranged from 0.003 to 0.397?µg?L^?1. The reported method is simple, sensitive, and accurate, and is a suitable alternative for routine monitoring of pesticide residues at ultra-trace levels. The analysis revealed the presence of propoxur at a concentration of 0.072?µg?L^?1 in stream water.     

Response surface optimisation applied to a headspace-solid phase microextraction-gas chromatography-mass spectrometry method for the analysis of volatile organic compounds in water matrices

A new method for the simultaneous determination of 12 volatile organic compounds (trans-1,2-dichloroethene, 1,1,1-trichloroethane, benzene, 1,2-dichloroethane, trichloroethene, toluene, 1,1,2-trichloroethane, tetrachloroethene, ethylbenzene, m-, p-, o-xylene) in water samples by headspace solid phase microextraction (HS–SPME)–gas chromatography mass spectrometry (GC–MS) was described, using a 100?µm PDMS (polydimethylsiloxane) coated fibre. The response surface methodology was used to optimise the effect of the extraction time and temperature, as well as the influence of the salt addition in the extraction process. Optimal conditions were extraction time and temperature of 30?min and ?20°C, respectively, and NaCl concentration of 4?mol?L^?1. The detection limits were in the range of 1.1?×?10^?3–2.3?µg?L^?1 for the 12 volatile organic compounds (VOCs). Global uncertainties were in the range of 4–68%, when concentrations decrease from 250?µg?L^?1 down to the limits of quantification. The method proved adequate to detect VOCs in six river samples.     

Ligandless-ultrasound-assisted emulsification microextraction followed by inductively coupled plasma-optical emission spectrometry for simultaneous determination of heavy metals in water samples

In this study, a simple and efficient method of ligandless-ultrasound-assisted emulsification microextraction (LL-USAEME) followed by inductively coupled plasma-optical emission spectrometry (ICP-OES) has been developed for simultaneous extraction, preconcentration and determination of manganese, cadmium, cobalt and nickel in water samples. In the proposed approach, tetrachloroethylene was selected as extraction solvent. The effect of important experimental factors such as volume of extraction solvent, pH, sonication time, salt concentration, and temperature was investigated by using a fractional factorial design (2^5?1) to identify important factors and their interactions. In the next step, a Box-Behnken design (BBD) was applied for optimisation of significant factors. The obtained optimal conditions were: 30?µL for extraction solvent, 12 for pH, 5?min for sonication time, and 5% w/v for salt concentration. The limits of detections (LODs) for Cd(II), Co(II), Mn(II) and Ni(II) were 0.20, 0.13, 0.21 and 0.28?µg?L^?1, respectively. Relative standard deviations (RSD, C?=?200.0?µg?L^?1, n?=?9) were between 3.4–7.5% and the calibration graphs were linear in the range of 0.25 to 1000.0?µg?L^?1 for Mn, 0.5–1000.0?µg?L^?1 for Co and Ni and 1.0–250.0?µg?L^?1 for Cd. The determination coefficients (R ²) of the calibration curves for the analytes were in the range of 0.993 to 0.999. The proposed method was validated by using two certified reference materials, and also the method was applied successfully for the determination of heavy metals in different real water samples.     

Determination of total antimony(III,V) by square-wave anodic stripping voltammetry with in situ plated bismuth-film electrode

A sensitive and reliable method is described for the determination of total Sb(III,?V) at traces levels by Osteryoung square-wave anodic stripping voltammery (OSWASV). This method is based on the co-deposition of Sb(III,?V) with Bi(III) onto an edge-plane pyrolytic graphite substrate at an accumulation step. OSWASV studies indicated that the co-deposited antimony was oxidised with anodic scans to give an enhanced anodic peak at about 450?mV vs. Ag/AgCl (sat. KCl). The anodic stripping peak current was directly proportional to the total concentration of antimony in the ranges of 0.01–0.10?µg?L^?1, 0.10–1.0?µg?L^?1 and 1.0–18.0?µg?L^?1 with correlation coefficient higher than 0.995 when 2.0?mol?L^?1 hydrochloric acid was used. The detection limits calculated as S/N?=?3 was 5.0?ng?L^?1 in 2.0?mol?L^?1 hydrochloric acid at 180?s deposition time. The relative standard deviation was 5% (n?=?6) at 0.10?µg?L^?1 level of antimony. The analytical results demonstrate that the proposed method is applicable to analyses of real water samples.     

Square wave voltammetric determination of diafenthiuron and its application to water,soil and insecticide formulation

A square wave cathodic stripping voltammetric (SWCSV) method has been developed for the determination of insecticide diafenthiuron. The procedure is based on controlled accumulation of the insecticide on a static hanging mercury drop electrode (SHMDE) at 0.00?mV (vs. Ag/AgCl) in Britton-Robinson buffer solution (pH 7.0). The insoluble mercury compound was reduced at ?510?mV during the cathodic potential scan. The peak currents were linearly related to insecticide concentration between 30.4 and 3200?µg?L^?1 . The detection and quantification limit were 9.1?µg?L^?1 and 30.4?µg?L^?1, respectively. The proposed analytical procedure was applied to natural water and soil samples. The method was extended to direct determination of diafenthiuron in insecticide formulation Polo® 50 WP and average content of 50.3?±?1.7 (m/m) at 90% confidence level, in close agreement with the 50.0% quoted by the manufacturer. HPLC comparison method indicated that accuracy was in agreement with that obtained by the proposed method.     

Evaluation of Manganese(II) and Manganese(VII) Speciation in Water Samples by Ion Pair High-performance Liquid Chromatography-inductively Coupled Plasma Mass Spectrometry

The speciation of Mn(II) and Mn(VII) is reported by ion pair chromatography. To optimize the separation, sample pH, ion pair reagent, Mn(II) complexing agent, and composition of mobile phase were characterized. The separation of Mn(II) and Mn(VII) was performed using ethylenediamine tetraacetic acid to complex Mn(II), tetrabutylammonium hydroxide as an ion pair reagent, and a C8 column. The separation of the manganese species was demonstrated by high-performance liquid chromatography-inductively coupled plasma mass spectrometry (HPLC ICP-MS). The conversion of Mn(VII) to Mn(II) occurred during the separation and influenced the quantification; hence, the factors affecting this process including the storage time, manganese species ratio, and sample matrix composition were evaluated and suitable calibration was demonstrated. The method was validated by characterization of the selectivity, specificity, linearity, limits of detection and quantification, repeatability, and intermediate precision. The detection limit for Mn(II) was 0.22 µg?L^?1, while for Mn(VII), the value was 1.55 µg?L^?1.     

Veterinary antimicrobials and antiparasitics in fee-fishing ponds: analytical method and occurrence*

ABSTRACT

The aim of this work was to develop and validate a method using online solid-phase extraction and ultra-high-performance liquid chromatography coupled to tandem mass spectrometry to determine residues of 22 veterinary drugs including sulfonamides, amphenicols, fluoroquinolones, benzimidazoles, trimethoprim (TMP) and oxytetracycline (OTC) in water from fee-fishing ponds. The optimal analytical conditions were as follows: XBridge C8 SPE column, Acquity UPLC CSH C18 analytical column, sample loading with water:methanol (98:2, v/v), mobile phase of water with 0.1% acetic acid:methanol (with gradient elution) and eluent flow rate of 0.3 mL min^?1. Quantification was performed in selected reaction monitoring mode and sulfadimethoxine-d₆, ciprofloxacin-d₈, florfenicol-d₃ and albendazole-d₃ were used as internal standards. Water samples collected from 11 fee-fishing ponds showed the presence of residues of FF (0.42–0.74 µg L^?1), albendazole (0.05–0.31 µg L^?1) and thiabendazole (0.45 µg L^?1). Thiamphenicol and TMP were detected at concentrations lower than the limits of quantification of the method (0.1 and 0.001 µg L^?1, respectively).     

Determination of Chromium (VI) in Airborne Particulate Matter by Electrothermal Atomic Absorption Spectrometry

Hexavalent chromium Cr(VI) is a well-established carcinogen associated with lung, nasal, and sinus cancer. Cr(VI) threshold limit values in workroom air have been recently lowered. Consequently, the currently available analytical methods are insufficiently sensitive or high cost. In this paper, a simple, cost-effective, sensitive, and reproducible method using solid-phase extraction with electrothermal atomic absorption spectrometry for determination of hexavalent chromium in airborne samples is reported. The method validation included selectivity, linearity, accuracy, and precision. Interferences from other ions likely to be present in airborne samples, including trivalent chromium, were tested and selectivity was demonstrated. The detection and quantification limits were, respectively, as low as 0.1 and 0.4?µg?L^?1. The linearity ranged from 0.5 to 50.0?µg?L^?1, with a regression coefficients exceeding 0.998. The extraction recovery exceeded 98%. The developed method was successfully compared with a reference spectrophotometric method. The performances achieved were similar to ion chromatography and high-performance liquid chromatography approaches. The novel method was tested on airborne samples collected from the workplace. The method’s performance suggests that it may be an alternative to high-cost techniques for monitoring occupational exposure to hexavalent chromium.