Development of new adsorbent chitin for column preconcentration and spectrophotometric trace determination of Ziram and Zineb in synthetic, commercial samples and food-stuffs

A procedure has been developed for the determination of zinc(II) bis(dimethyldithiocarbamate) (Ziram) or zinc(II) ethylenebisdithiocarbamate (Zineb) present in a large volume of aqueous solution after preconcentration on a column using chitin-1-(2′pyridylazo)-2-naphthol (PAN) as adsorbent. Ziram/Zineb are quantitatively retained on the column as Zn-PAN complex in the pH range 9.0-11.0 and at a flow rate of 1-8 ml/min. Complex adsorbed on chitin was eluted from the column with dimethylformamide (DMF) and absorbance of the eluate was measured at 550 nm against a reagent blank. Beer's law is obeyed over the concentration range 5.3-55.8 μg of Ziram and 6.8-49.0 μg of Zineb in 25 ml of the final DMF solution. Ten replicate determinations on a sample solution containing 45.22 μg of Ziram or 40.86 μg of Zineb gave a mean absorbance of 0.30 with a relative standard deviation 1.6 and 1.8%, respectively. The interference of various ions has been studied. Many alkali metals and metal salts do not interfere. The method has been employed to the determination of Ziram and Zineb in commercial samples and in various foodstuffs and the results were compared with the earlier reported methods.     

Spectrophotometric Determination of Ziram by Coprecipitating the Corresponding Copper(II) or Palladium(II) Complex with Naphthalene

A spectrophotometric method has been developed for the determination of zinc dimethyldithiocarbamate (ziram) by converting it into dimethyldithiocarbamate and coprecipitating its copper(II) and palladium(II) dimethyldithiocarbamate complexes and coprecipitating onto microcrystalline naphthalene. Palladium(II) and copper(II) complexes absorb strongly at 395 nm and 430 nm, respectively. The interference of various ions has been studied and the method has been applied to determine ziram in commercial samples and grains.     

Capillary electrophoretic determination of zinc dimethyldithiocarbamate (Ziram) and zinc ethylenebisdithiocarbamate (Zineb)

A simple and sensitive capillary electrophoretic method was developed for the separation and determination of Ziram and Zineb in boric acid buffer by direct UV absorbance detection at lambda=254 nm. The separation is dependent on pH and nature of the buffer. The detection limits (S/N=3) are 1.88x10(-6) mol/l (0.57 mug/ml) and 2.48x10(-6) mol/l (0.68 mug/ml) for Ziram and Zineb, respectively. The method was successfully applied to the analysis of wheat samples spiked with Ziram and Zineb.     

Spectrophotometric determination of ziram, ferbam and zineb with diphenylcarbazone

A procedure has been developed for the determination of ziram (zinc dimethyldithiocarbamate), ferbam (ferric dimethyldithiocarbamate) and zineb (zinc ethylenebisdithiocarbamate) after their decomposition and extraction of the diphenylcarbazone complexes of the zinc or iron into isobutyl methyl ketone. These complexes absorb strongly at 520 nm. The method is rapid, sensitive and selective and can be used for the determination of these dithiocarbamates in commercial and synthetic mixtures.     

Fourth-derivative spectrophotometric determination of fungicide ferbam (iron(III) dimethyldithiocarbamate) in a commercial sample and wheat grains using 2,2′-bipyridyl

A procedure has been developed for the direct fourth-derivative spectrophotometric determination of iron(III) dimethyldithiocarbamate by converting it into an iron(II) 2,2'-bipyridyl complex, which is then dissolved in Triton X-100. Beer's law is obeyed over the concentration range 0.5-20 microg mL(-1 )in the final solution. Various parameters such as the effect of pH and interference of large number of ions on the determination of ferbam have been studied in detail. The method is sensitive, highly selective and can be used for the determination of ferbam in a commercial sample and in mixtures with various dithiocarbamates (ziram, zineb, maneb, etc.) and from wheat grains.     

Spectrophotometric determination of ziram in a commercial sample and wheat by extraction of its copper dimethyldithiocarbamate complex into molten naphthalene

A method was developed for the determination of zinc(II) dimethyldithiocarbamate by converting it into the copper(II) dithiocarbamate complex, which is then extracted into molten naphthalene. The absorbance is measured at 430 nm versus a reagent blank. Beer's law is obeyed for concentrations of 0.63 x 10(-3) to 17.2 x 10(-3) g/L in the final solution. The method is sensitive and was applied to the determination of ziram in a commercial sample and in wheat grain.     

Spectrophotometric determination of some dithiocarbamates

A procedure has been developed for the determination of six dithiocarbamates [sodium dimethyldithiocarbamate (dibam), sodium diethyldithiocarbamate (NaDDC), tetramethylthiuram disulphide (thiram), zinc dimethyldithiocarbamate (ziram), sodium N-methylpiperazinecarbodithioate and potassium morpholine-4-carbodithioate] in microgram quantities by converting them into selenium dithiocarbamate complexes, which are then extracted into chloroform and measured at 430 nm against a reagent blank. The method is sensitive and can be used for the determination of dithiocarbamates in commercial samples and synthetic mixtures.     

Spectrophotometric determination of iron(III) dimethyldithiocarbamate (ferbam)

A spectrophotometric method was developed for the determination of ferbam (iron(III) dimethyldithiocarbamate) by converting it into an iron-phenanthroline complex, which was then absorbed on microcystalline naphthalene in the presence of tetraphenylborate, and the absorbance was measured at 515 nm against a reagent blank. The molar absorptivity of the complex was 1.2 x 10(4)l mol(-1)cm(-1). Ten replicate analyses of a sample solution containing 150 mug of ferbam gave a relative standard deviation of 0.84%. Beer's law was obeyed over the concentration range 22.4-372.9 mug of ferbam. The effects of various factors such as reagent concentration and naphthalene, shaking time and diverse ions were studied in detail. The method is sensitive and selective and can be applied to the direct determination of ferbam in commercial samples and in mixtures containing various other dithiocarbamates (e.g. ziram, zineb and maneb) in foodstuffs.     

Flow injection-FTIR determination of dithiocarbamate pesticides

A flow injection Fourier transform infrared spectrometric procedure has been developed for the determination the dithiocarbamate pesticides Ziram and Thiram in solid samples. All the operations involved, such as extraction, filtration and measurement, were integrated in the experimental set-up in order to avoid excessive manipulation of samples and standards. Ultrasonic assisted and mechanical extraction were evaluated for the solubilization of the analytes and, additionally, the effect of carrier flow rate, sample loop volume and the ratio between sample mass and volume of solvent employed were studied. Quantitative extractions with chloroform were obtained for both Ziram and Thiram, after 5 and 2 min, respectively, of mechanical shaking of sample slurries. Absorbance measurement, in the wavenumber range of 1600-1460 cm-1 for Ziram and 1400-1315 cm-1 for Thiram, was carried out, and the area values of the peaks obtained, as a function of time, were interpolated in external calibration lines prepared from standard solutions of Ziram and Thiram in chloroform. Analyses of commercial formulations and spiked soil samples incubated two weeks were in a good agreement with values found by other methodologies. Absolute detection limits of 400 micrograms for Ziram and 785 micrograms for Thiram and variation coefficients of 6.4% and 2.5% were obtained by use of the aforementioned methodology.     

Dispersive liquid-liquid microextraction of Fe(II) and Cu(II) with diethyldithiocarbamate and their simultaneous spectrophotometric determination using mean centering of ratio spectra

A new dispersive liquid-liquid microextraction (DLLME) method for preconcentration of trace quantities of Fe(II) and Cu(II) followed by their spectrophotometric determination has been developed. For the extraction, an appropriate mixture of ethanol (the disperser solvent) and carbon tetrachloride (the extraction solvent) was injected rapidly into the water sample containing Fe(II) and Cu(II) after formation of complexes with diethyldithiocarbamate. Mean centering (MC) of ratio spectra has been used for simultaneous determination of Fe(II) and Cu(II). Linear range of the method is 1.0–100 ng/mL for Fe(II) and 0.3–100 ng/mL for Cu(II), the detection limit is 0.53 ng/mL and 0.14 ng/mL Cu(II), resp. The interference effect of some anions and cations is reported. The method was applied to the determination of Fe(II) and Cu(II) in well water samples.     

Sorption preconcentration and separation of Palladium(II) and Platinum(IV) for visual test and densitometric determination

We have demonstrated the advantages of the dynamic preconcentration and separation of Pd(II) and Pt(IV) on paper carriers modified with 3-methyl-2,6-dimercapto-1,4-thiopyrone. The optimal conditions of the solid-phase reaction have been determined in Pd(II) sorption; after its separation Pt(IV), has been preconcentrated by sorption as its dimercaptides. Test scales have been produced for the visual determination of 0.5–40 μg Pd(II) and 1–195 μg Pt(IV) in 10- and 100 mL-samples, respectively. In addition, a procedure of their sorption-chromaticity densitometry determination from a single aliquot portion has been developed with detection limits of 5 and 1 ng/mL, respectively, and a procedure of Pd(II) determination using a test strip (c _min = 0.40 mg/L) has been proposed. The procedures have been applied to the determination of palladium and platinum in electrolytes, sludges, and alloys.     

Fluorescence Reaction of 5- (p-Methoxyphenylazo)-8-(p-tolylsulfonamido)quinoline with Cobalt(II) and Its Analytical Application

Abstract

5-(p-Methoxyphenylazo)-8-(p-tolylsulfonamido) quinoline(MTAQ) has been synthesized. The product was checked by IR, theroograviae-try, NMR and elemental analysis. A highly sensitive spectrofluorim-etric method has been developed for the determination of cobalt(II) based on the formation of a complex with MTAQ in slightly basic medium aqueous solution and In the presence of nonionic surfactant, tween-80. The complex shows two excitation maxima at 304 nm and 338 nm, its emission maximum is centred at 402 nm. The fluorescence intensity is proportional to cobalt(II) concentration in the range of 0-85 ppb. The method has good selectivity and has been applied to the direct fluorimetric determination of trace cobalt(II) in pig's liver, Dianchi shrimp and celery.     

Determination of the fungicide ferbam in wheat grains after adsorption onto microcrystalline naphthalene

A procedure was developed for the determination of iron(III) dimethyldithiocarbamate by converting it into iron(II)-bathophenanthroline-tetraphenylborate complex, which was then adsorbed onto microcrystalline naphthalene. The absorbance was measured at 534 nm against a reagent blank. Beer's Law was obeyed over the concentration range of 0.4-20 microg mL in final solution. Ten replicate determinations on 70 microg ferbam solutions gave a mean absorbance of 0.36, with a relative standard deviation of 0.91%. The method is sensitive and highly selective. It was applied for the determination of ferbam in a commercial sample and in mixtures with various dithiocarbamates (ziram, zineb, maneb) and wheat grains.     

Potentiometric titration of Co(II) in presence of Co(III)

A potentiometric titration for cobalt(II) determination in the presence of Co(III) based on the oxidation of Co(II) with Na₂CrO₄ in ethylenediamine medium and back-titration of the oxidant excess with (NH₄)₂Fe(SO₄)₂ in acid medium is described. The titration is monitored with a Pt indicator electrode and carried out until the greatest jump of potential from one drop of titrant appears. A RSD smaller than 1.5% has been obtained for 50–300 μmol Co(II). The method proposed was applied in the analysis of a new type electroless copper plating solutions containing Co(II)-ethylenediamine complex compounds as reducing agents. Cu(II), Co(III) and Cr(III) do not interfere in the determination of Co(II).     

Stopped-flow spectrophotometric determination of nM level of Pb(II) using 5,10,15,20-terakis(1-methylpyridinium-4-yl)porphine

A spectrophotometric determination method for nM levels of Pb(II) has been developed using a stopped-flow spectrophotometer with cationic water-soluble porphyrin. The stopped-flow spectrophotometer allows the monitoring of the incorporation reaction of the Pb(II) ion into 5,10,15,20-terakis(1-methylpyridinium-4-yl)porphine (TMPYP) within a narrow time window (2.5 s) at pH 10.5–12.0 before the Pb-TMPYP complex is replaced with other foreign metal ions, since usually the Pb-TMPYP complex is very labile and readily replaced with other metal ions. This improved the selectivity of Pb(II) determination as compared to the conventional spectrophotometric determination of Pb(II) using water-soluble porphyrins.     

Stripping Voltammetric Determination of Pb(II) and Cd(II) Based on the Multiwalled Carbon Nanotubes-Nafion-Bismuth Modified Glassy Carbon Electrodes

Abstract

In this work, a new method for the simultaneous determination of Pb(II) and Cd(II) on the multiwalled carbon nanotubes (MWNT)-Nafion-bismuth modified glassy carbon electrode (GCE) using square-wave anodic stripping voltammetry has been studied. Scanning electron microscopy was used to investigate the characteristics of the MWNT-Nafion-bismuth modified GCE. Well-defined sharp stripping peaks were observed in the determination of Pb(II) and Cd(II) simultaneously on this electrode. Under optimized conditions, the lowest detectable concentrations were 50 ng/l for Pb(II) and 80 ng/l for Cd(II) under a 10 min preconcentration. The attractive performances of MWNT-Nafion-bismuth modified GCE demonstrated its application for a simple, rapid, and harmless determination of trace heavy metals.     

Non-Extractive Simultaneous Spectrophotometric Determination of Trace Quantities of Palladium(II) and Tungsten(VI)

A second order derivative spectrophotometric method has been developed for the simultaneous determination of Palladium(II) and Tungsten(VI) using 3,4-dihydroxybenzaldehyde isonicotinoylhydrazone (3,4-DHBINH) as a new complexing agent. The Pd(II) reacts with 3,4-DHBINH in the pH range from 3 to 7 to form green colored solution. The absorbance calibration curves were constructed for palladium(II) at 362 nm (0.53～6.40 μg/ml) and tungsten(VI) at 374 nm (0.92～11.40 μg/ml). The metal ions interfere with each other in determination of zero order as well as the first order spectrophotometry. The optimum condition for maximum color development and other analytical parameters were evaluated. The method was applied successfully for the determination of palladium in hydrogenation catalyst and tungsten in industrial waste water samples.     

Radiochemical solvent extraction of Mn(II) using54Mn tracer

A radiochemical solvent extraction method has been developed for the determination of Mn(II) using⁵⁴Mn tracer. Mn(II) is complexed with 2-thenoyltrifluoroacetone (TTA) at pH 8.5 and extracted in isobutyl methyl ketone (IBMK). Different parameters affecting the extraction, and interferences due to diverse ions have been studied. The method can be used for the determination of Mn in microgram amounts.     

邻菲啰啉计算光度法同时测定生物浸出样品中Fe（Ⅱ）和Fe（Ⅲ）

邻菲哕啉光度法常用于Fe（Ⅱ）测定,但受到试样中Fe（Ⅲ）对测定的影响,因此不能直接用于生物浸出样品中Fe（Ⅱ）和Fe（Ⅲ）的同时测定．为此,基于Fe（Ⅱ）邻菲哕啉特征吸收曲线以及混合铁中Fe（Ⅲ）对Fe（Ⅱ）测定的线性影响关系,建立了基于Fe（Ⅱ）和全铁同时测定Fe（Ⅱ）和Fe（Ⅲ）的计算光度法,并研究了生物浸出样品中典型金属离子（Cu^2＋、Ni^2＋、Cd^2＋、Co^2＋）以及试样溶解与储放对测定的影响．方法可准确地测定含铁次生矿物和生物浸出液中铁价态组成,应用于生物浸出矿渣、细胞表面中常量或微量的Fe（Ⅱ）和Fe（Ⅲ）组成分析,具有简便快速的特点．     

Fourier transform infrared spectrometric determination of Ziram

A procedure has been developed for vapour-phase Fourier transform infrared determination of Ziram, a dithiocarbamate pesticide. The method is based on the evolution of CS₂, after decomposition of the dithiocarbamate with diluted H₂SO₄ at 50°C. The CS₂ evolved was swept by a carrier flow of nitrogen to a laboratory-made infrared gas cell of 39 mm pathlength and 490 μl volume. The signals were registered as a function of time. The area of peaks obtained from absorbance measurement in the wavenumber range between 1600 and 1450 cm⁻¹ were interpolated in a calibration line established from Ziram standards treated in the same way as samples. The method provided an absolute limit of detection of 0.055 mg, a variation coefficient of the order of 6% for an analyte mass of 50 mg, and an analysis time of 3.5 min.