Plastic membrane electrodes for the potentiometric determination of codeine in pharmaceutical preparations

Four PVC membrane electrode systems responsive to codeinium cation are described. These electrodes are based on the use of the ion-association complexes of the codeinium cation with tetraphenylborate and reineckate counter-anions as ion-exchange sites in a PVC matrix plasticized with dioctylphthalate and dibutylsebacate. The performance characteristics of these electrodes reveal fast, stable and near-Nernstian responses for codeine down to concentrations of 3.5–7.0 × 10^–5 M. Over the pH range 2.5–7, the electrodes are satisfactory for manual and flow injection determination of codeine in various pharmaceutical preparations. There is negligible interference from a number of inorganic and organic cations and some common drug excipients. In the direct determination of 30 g/ml -1.0 mg/ml codeine, the average recovery is 100.6% and the mean standard deviation is ± 0.8%. The results compare favorably with those obtained by the British Pharmacopoeia method.     

PVC matrix membrane sensor for potentiometric determination of cetylpyridinium chloride.

A novel cetylpyridinium chloride-selective membrane sensor consisting of cetylpyridinium-ferric thiocyanate ion pairs dispersed in a PVC matrix placticized with dioctylphthalate is described. The electrode shows a stable, near-Nernstian response for 1 x 10(-3)-1 x 10(-6) mol l-1 cetylpyridinium chloride (CPC) at 25 degrees C over the pH range 1-6 with a cationic slope of 57.5 +/- 0.4. The lower detection limit is 8 x 10(-7) mol l-1 and the response time is 30-60 s. Selectivity coefficients for CPC relative to a number of interfering substances were investigated. There is negligible interference from many cations, anions and pharmaceutical excipients; however, cetyltrimethylammonim bromide (CTMAB) interfered significantly. The determination of 0.5-350 micrograms/ml of CPC in aqueous solutions shows an average recovery of 98.5% and a mean relative standard deviation of 1.6% at 56.0 micrograms/ml. The direct determination of CPC in Ezafluor mouthwash gave results that compare favorably with those obtained by the British Pharmacopoeia method. Precipitation titrations involving CPC as titrant are monitored with a CP sensor. The CP electrode has been utilized as an end point indicator electrode for the determination of anionic surfactants in some commercial detergents.     

A novel tetrachlorothallate (III)-PVC membrane sensor for the potentiometric determination of thallium (III)

A novel tetrachlorothallate (III) (TCT)-selective membrane sensor consisting of tetrachlorothallate (III)-2,3,5-triphenyl-2-H-tetrazolium ion pair dispersed in a PVC matrix plasticized with dioctylphthalate is described. The electrode shows a stable, near-Nernstian response for 1×10⁻³-4×10⁻⁶ M thallium (III) at 25 °C with an anionic slope of 56.5±0.5 over the pH range 3-6. The lower detection limit and the response time are 2×10⁻⁶ M and 30-60 s, respectively. Selectivity coefficients for Tl(III) relative to a number of interfering substances were investigated. There is negligible interference from many cations and anions; however, iodide and bromide are significantly interfere. The determination of 0.5-200 μg ml⁻¹ of Tl(III) in aqueous solutions shows an average recovery of 99.0% and a mean relative standard deviation of 1.4% at 50.0 μg ml⁻¹. The direct determination of Tl(III) in spiked wastewater gave results that compare favorably with those obtained by the atomic absorption spectrometric method. The electrode was successfully applied for the determination of thallium in zinc concentrate. Also the tetrachlorothallate electrode has been utilized as an end point indicator electrode for the determination of thallium using potentiometric titration.     

PVC membrane electrodes for potentiometric determination of tripelennamine

The construction of PVC matrix type tripelennamine ion selective electrodes and their use for direct potentiometry, potentiometric titration and flow injection analysis of tripelennamine cation are described. The membranes of these electrodes consist of tripelennamine-tetraphenylborate, reineckate and picrylsulfonate ion-association complexes dispersed in PVC matrix with tributyl phosphate (TBP) plasticizer. The electrodes exhibit near-Nernstian response over the concentration range of 10^–1-10^–4 M tripelennamine over the pH range 4.5–8.0. Selectivity coefficients data obtained for 17 different organic and inorganic ions are presented. The results obtained for the determination of 29 g/ml-29 mg/ml of tripelennamine with the proposed electrodes show average recoveries of 99.5–99.9% and mean standard deviations of 0.6–1.2%. The data agree well with those obtained by the standard methods.     

A PVC plasticized membrane sensor for nickel ions

A new PVC membrane sensor, which is highly selective towards Ni (II) ions, has been developed using a thiophene-derivative Schiff base as the ionophore. The best performance was exhibited by the membrane having the composition percentage ratio of 5:3:61:31 (ionophore:NaTPB:DBP:PVC) (w/w), where NaTPB is the anion excluder, sodium tetraphenylborate and DBP is the plasticizing agent (dibutyl phthalate). The membrane exhibited a good Nernstian response for nickel ions over the concentration range of 1.0 × 10⁻¹–5.0 × 10⁻⁶ M (limit of detection is 1.8 × 10⁻⁶ M) with a slope of 29.5 ± 1.0 mV per decade of activity. It has a fast response time of <20 s and can be used for a period of 4 months with good reproducibility. The sensor is suitable for use in aqueous solutions of a wide pH range of 3.2–7.9. The sensor shows high selectivity to nickel ions over a large number of mono-, bi- and trivalent cations. It has been successfully used as an indicator electrode in the potentiometric titration of nickel ions against EDTA and also for direct determination of nickel content in real samples – wastewater samples from electroplating industries and Indian chocolates.     

PVC membrane based potentiometric sensors for uranium determination

Two novel uranyl PVC matrix membrane sensors responsive to uranyl ion are described. The first sensor incorporates tris(2-ethylhexyl)phosphate (TEHP) as both electroactive material and plasticizer and sodium tetraphenylborate (NaTPB) as an ion discriminator. The sensor displays a rapid and linear response for UO₂²⁺ ions over the concentration range 1×10⁻¹–2×10⁻⁵ mol l⁻¹ UO₂²⁺ with a cationic slope of 25.0±0.2 mV decade⁻¹. The working pH range is 2.8–3.6 and the life span is 4 weeks. The second sensor contains O-(1,2-dihydro-2-oxo-1-pyridyl)-N,N,N′,N′-bis(tetra-methylene)uronium hexafluorophosphate (TPTU) as a sensing material, sodium tetraphenylborate as an ion discriminator and dioctyl phenylphosphonate (DOPP) as a plasticizer. Linear and stable response for 1×10⁻¹–5×10⁻⁵ mol l⁻¹ UO₂²⁺ with near-Nernstian slope of 27.5±0.2 mV decade⁻¹ are obtained. The working pH range is 2.5–3.5 and the life span of the sensor is 6 weeks. Interference from many inorganic cations is negligible for both sensors. However, interference caused by some ions (e.g. Th⁴⁺, Cu²⁺, Fe³⁺) is eliminated by a prior ion exchange or solvent extraction step. Direct potentiometric determination of as little as 5 μg ml⁻¹ uranium in aqueous solutions shows an average recovery of 97.2±1.3%. Application for the determination of uranium at levels of 0.01–1 wt.% in naturally occurring and certified ores gives results with good correlation with data obtained by X-ray fluorescence.     

Determination of Fluoride Ions in Mouthwash Samples by a PVC Membrane Samarium(III) Sensor

Abstract

In this study, a new ion-selective electrode for Sm³⁺ is described, illustrating 2-[(E)-1-(1H-pyrrol-2-yl)methylidene]-1-hydrazinecarbothioamide (PMH) in a poly(vinylchloride) (PVC) membrane with nitrobenzene (NB) as a plasticizer and sodium tetraphenyl borate (NaTPB) as an anionic additive. The proposed sensor exhibited a Nernstian response for Sm³⁺ ions over a wide concentration range between 1.0 × 10^?2 and 1 × 10^?6 M, with a detection limit of 5.2 × 10^?7 M in the pH range of 4.2–8.5. Moreover, the sensor displayed the Nernstian slope of 19.8 ± 0.3 mV per decade, having a fast response time within 10 s over the entire concentration range. This electrode presented very good selectivity and sensitivity toward the Sm³⁺ ions over a wide variety of cations, including alkali, alkaline earth, transition-metal, and heavy-metal ions. It was used as an indicator electrode in the potentiometric titration of Sm³⁺ ions with EDTA. The membrane sensor was also applied to the determination of fluoride ions in mouthwash samples.     

PVC matrix membrane electrodes based on cobalt and nickel phenanthroline complexes for selective determination of cobalt(II) and nickel(II) ions

Potentiometric sensors for determining cobalt and nickel ions are described. They are based on the use of cobalt and nickel tris(1,10-phenanthroline)-TPB as electroactive compounds dispersed in plasticized poly(vinyl chloride) matrix. The sensors exhibit fast, near-Nernstian responses for cobalt and nickel-phenanthroline cations over the pH range 3–11 with a slope of 30.3 ± 0.3 mV/concentration decade. In the presence of excess 1,10-phenanthroline reagent, cobalt(II) and nickel(II) ions at concentration levels as low as 4 × 10^–6 M are accurately determined. The results show an average metal ion recovery of 98.5% with a mean standard deviation of 0.5%. Cobalt in organometallic compounds and nickel in silicate rocks are determined by these sensors and results agreeing fairly well with atomic absorption spectrometry are obtained.     

A novel ion selective membrane potentiometric sensor for direct determination of Fe(III) in the presence of Fe(II)

A new PVC membrane potentiometric sensor that is highly selective to Fe(III) ions was prepared by using 2-[(2-hydroxy-1-propenyl-buta-1,3-dienylimino)-methyl]-4-p-tolylazo-phenol [HPDTP] as a suitable carrier. The electrode exhibits a linear response for iron(III) ions over a wide concentration range (3.5 × 10⁻⁶ to 4.0 × 10⁻²) with a super Nernstian slope of 28.5 (±0.5) per decade. The electrode can be used in the pH range from 4.5 to 6.5. The proposed sensor shows fairly a good discriminating ability towards Fe³⁺ ion in comparison to some hard and soft metals such as Fe²⁺, Cd²⁺, Cu²⁺, Al³⁺ and Ca²⁺. It has a response time of <15 s and can be used for at least 2 months without any measurable divergence in response characteristics. The electrode was used in the direct determination of Fe³⁺ in aqueous samples and as an indicator electrode in potentiometric titration of Fe(III) ions.     

Nickel(II) selective membrane potentiometric sensor using a recently synthesized mercapto compound as neutral carrier

A PVC membrane electrode for Ni²⁺ ions based on a recently synthesized mercapto compound, as an ionophore was prepared. The electrode exhibits a Nernstian slope of 28-30 mV per concentration decade at wide concentration range of (1.0×10⁻²-1.0×10⁻⁷ M). It has a fast response time of <15 s and can be used for at least 4 weeks. The potentiometric response is independent of the pH of the test solution in the pH range 5-8.5. The proposed electrode revealed good selectivities over a wide variety of other cations including alkali, alkaline earth, transition and heavy metal ions. It was successfully applied to the direct determination and potentiometric titration of nickel ion with EDTA.     

Flow-injection potentiometric determination of triiodide by plasticized poly(vinyl chloride) membrane electrodes and its application to the determination of chlorine-containing disinfectants

Plasticized poly(vinyl chloride) (PVC) membranes of different compositions were tested for use in the construction of potentiometric flow detectors for triiodide. A membrane with a 2:1 (w/w) 2-nitrophenyl octyl ether to PVC ratio was selected. The influence of thiosulphate in the carrier solution composition and of the flow-injection variables on the determination of triiodide was studied. In the selected conditions, a linear relationship between peak height and log[I₃⁻] was obtained between 5 × 10⁻⁶ and 1 × 10⁻⁴ mol l⁻¹ triiodide. Peak height relative standard deviations for 2 × 10⁻⁵ and 1 × 10⁻⁴ mol l⁻¹ triiodide were ±0.4 and ±1.8%, respectively, and sampling frequency was 80 samples per hour. The method proposed was applied satisfactorily to the iodometric determination of different chlorine-containing disinfectants, among them trichloroisocyanuric acid and dichloroisocyanurate in several types of commercial sample.     

PVC膜修饰电极上零电流示波电位滴定法测定硼的研究

以氯化十六烷基吡啶（ＣＰＣ）和氟硼酸钠形成的离子缔合物为活性物质，制成ＰＶＣ膜涂层石墨电极，提出了一个快速测定硼的零电流示波电位滴定法。以ＣＰＣ为滴定剂，用ＰＶＣ膜电极为指示电极，甘汞电极为参比电极，利用阴极射线示波器荧光屏上荧光点的突然位移来指示ＣＰＣ滴定硼的终点，具有灵敏、准确、快速等特点，用该法测定玻璃中的硼，结果良好。     

PVC based 5,10,15,20-tetrakis (4-methoxyphenyl) porphyrinatocobalt(II) membrane potentiometric sensor for arsenite

PVC based membranes of 5,10,15,20-tetrakis(4-methoxyphenyl)porphyrinatocobalt(II) (TMOPP-Co) (I) as electroactive material with dibutyl butyl phosphonate (DBBP), dioctyl phthalate (DOP), 1-chloronaphthalene (CN), tri-n-butyl phosphate (TBP) and tris(2-ethylhexyl) phosphate (TEP) as plasticising solvent mediators have been prepared and tried for arsenite determination. The membrane having a composition 150:5:150 (PVC:I:DBBP) exhibited the best results with linear potential response in the concentration range of 7.9 × 10⁻⁵ to 1.0 × 10⁻¹ M of AsO₂⁻ with a slope of 28.8 mV/decade. The useful pH range of the sensor is 6.0-10.5. The membrane worked satisfactorily in non-aqueous medium up to 5% (v/v) non-aqueous content. The selectivity coefficient values for mono- and divalent anions indicate good selectivity for arsenite over a large number of anions.     

Development of new potentiometric sensors for the determination of proguanil hydrochloride in serum and urine

Potentiometric electrodes were developed for the rapid determination of proguanil hydrochloride in pure samples, pharmaceutical preparations and spiked serum and urine samples using PVC membrane,screen printed(SPE), coated wired(CWE), carbon paste(CPE) and modified carbon paste(MCPE)electrodes based on the ion-exchanger of proguanil with phosphotungestic acid(Pr-PT) as a chemical modifier. The prepared electrodes showed Nernestian slopes of 59.7, 58.1, 58.5, 58.5 and 57.0 for the PVC,SPE, CWE, CPE and MCPE for the proguanil ions in a wide concentration range of 1.0 * 10~(-5)–1.0 * 10~(-2)mol L~(-1) at 25°C with detection limits of 7.94 * 10~(-6), 1.0 * 10~(-5), 1.0 * 10~(-6), 7.07 * 10~(-6) and 2.5 * 10~(-6) mol L~(-1), respectively. The prepared electrodes exhibited high proguanil selectivity in relation to several inorganic ions and sugars and they could be successfully utilized for its determination in pure solutions, pharmaceutical preparations and serum and urine samples using the direct potentiometry and standard addition methods with very good recovery values.     

Magnesium-tetrazaporphyrin incorporated PVC matrix as a new material for fabrication of Mg(2+) selective potentiometric sensor

Membrane incorporating [Mg{(TAP)(SBn)₈}] complex, (I), as ionophore with composition I:NaTPB:DOP:PVC in the ratio 10:2:133:200 (w/w) exhibits the best result for potentiometric sensing of Mg²⁺ ions. This gives linear potential response in the concentration range of 9.4×10⁻⁶ to 1.0×10⁻¹ M with a slope of 29.2±0.4 mV per decade of activity of Mg²⁺. Standard deviation in observed values of potentials in this concentration range, from the least square fit line, found to be 2.91 mV with 90% confidence limit lying within ±0.4 mV per decade of activity. The electrode works satisfactorily in the pH range 3.5-7.8 and shows a fast response time of 13±2 s. It shows good selectivity for Mg²⁺ over other mono-, bi- and tri-valent cations. Only K⁺ and Zn²⁺ cause slight interference if present at concentrations ≥1.0×10⁻⁵ M. The electrode is durable and can be used over a period of 5 months with good reproducibility (∼1% error). It has been successfully used as an indicator electrode in potentiometric titration of Mg²⁺ against EDTA as well as for the determination of Mg²⁺ in simulated mixtures.     

Fabrication of a Ho~(3+)-PVC membrane sensor based on N-phenyl-2-(thiophen-2-ylmethylene)hydrazinecarbothioamide for determination of holmium ions

In this research,a new poly（vinyl chloride）（PVC） membrane sensor for Ho³⁺ ion based on N-phenyl-2-（thiophen-2- ylmethylene）hydrazinecarbothioamide（PHC） as an ionophore was prepared.This sensor demonstrated good selectivity and sensitivity towards the holmium ion in comparison with variety of cations,including alkali,alkaline earth,transition and heavy metal ions.The effect of membrane composition and pH on the response properties of the electrode was investigated.In detail,the suggested sensor exhibited a Nernstian behavior(with a slope of 20.4±0.3 mV decade^-1) in the range of 1.0×10^-6 to 1.0×10^-2 mol/L with a detection limit of 6.2×10^-7 mol/L.The response time was relatively quick in the whole concentration range（～5 s）.The sensor usage was found to be at least 10 weeks in a pH range of 3.3-10.9.It was successfully applied in determination of fluoride ions in mouth wash preparations.     

盐酸依匹斯汀PVC膜电极的研制及应用

以四苯硼酸钠与盐酸依匹斯汀生成的离子缔合物为电活性物质,研制了盐酸依匹斯汀PVC膜选择性电极。在pH 5的HCl-NaOH溶液中,电极的线性范围为6.3×10-7~1.0×10-1mol/L,斜率为49 mV/pC(10℃),检出限为1.89×10-7mol/L。应用此电极测定药物中盐酸依匹斯汀含量,RSD3%,回收率为97.5%~100.2%。     

A novel uranyl membrane sensor with potentiometric anionic response

A novel potentiometric uranyl membrane sensor with a divalent anionic response is developed, characterized and used for determination of uranyl ion. The sensor incorporates triethylenetetramine (TETA) as an ionophore in poly(vinyl chloride) matrix membrane (PVC) plasticized with o-nitrophenyloctyl ether (o-NPOE). In strong sulphate test solutions, UO₂²⁺ ion forms a highly stable [UO₂(SO₄)₂]²⁻ anion, extractable in TETA as {(2TETAH)²⁺ [UO₂(SO₄)₂]²⁻} complex. Formation of the complex is confirmed and characterized by elemental analysis, mass spectrometry and infrared spectrometry. Sensor based on this system displays at pH 2.5-3.8 a linear response over the concentration range of 1.0 × 10⁻¹-3.5 × 10⁻⁵ mol l⁻¹ uranium with a near-Nernstian calibration slope of −26.5 ± 0.3 mV decade⁻¹. The lower limit of detection is ∼5 μg ml⁻¹, the lifetime is 12 weeks and negligible interferences are caused by most common cations. Validation of the assay method reveals excellent performance characteristics in terms of sensitivity, selectivity, fast response and potential stability. The sensor is used for the determination of 0.01-7.09 wt% uranium in naturally occurring and certified ore samples. The results show an average recovery of 97.6% and compare fairly well with data obtained using X-ray fluorescence technique.     

Hydrogen chromate PVC matrix membrane sensor for potentiometric determination of chromium(III) and chromium(VI) ions

A novel potentiometric Cr(6+) PVC matrix membrane sensor incorporating nickel tris(1,10-bathophenanthroline) hydrogen chromate as an electroactive material and 2-nitrophenyl phenyl ether as solvent mediator is described. In a phosphate buffer solution of pH 5, the sensor displays a rapid and linear response for Cr(6-) over the concentration range 2 x 10(-2)-8 x 10(-6) M with an anionic slope of 55.5 +/- 0.2 mV decade(-1) and a detection limit of the order of 0.4 microg ml(-1). The sensor is used for sequential determination of Cr(6+) and Cr(3+) by direct monitoring of Cr(6+) followed by oxidation of Cr(3+) and measurement of the total chromium. The average recoveries of Cr(3+) and Cr(6+) at concentration levels of 0.5-50 microg ml(-1) are 98.1 +/- 0.4% and 99.1 +/- 0.4% respectively. Redox and precipitation titrations involving Cr(6+) as a titrant are monitored with the sensor. Cr(3+) and/or Cr(6+) in wastewaters of some industries (e.g., leather tanning, electroplating, aluminum painting) and the chromium contents of some alloys and refractory bricks are assessed. The results agree fairly well with data obtained using the standard diphenylcarbazide spectrophotometric method.     

Silver(I)-selective membrane potentiometric sensor based on two recently synthesized ionophores containing calix[4]arene

Two new PVC membrane electrodes that are highly selective to Ag(I) ions were prepared using (L₁) calyx[4]arene (L₂) as two suitable neutral carriers. The silver(I) ion selective electrodes exhibit a good response for silver ion over a wide concentration range of 1.0 × 10⁻¹ to 4.2 × 10⁻⁶ M (L₁) and 1.0 × 10⁻¹ to 6.5 × 10⁻⁶ M (L₂) with a Nernstian slope of 60 mV per decade (L₁) and 58 mV per decade (L₂) at 25°C, and was found to be very selective, precise, and usable within the pH range 4.0–8.0. They have a response time of <15 s and can be used for at least 3 months without any measurable divergence in potential. The proposed sensors show a fairly good discriminating ability towards Ag⁺ ion in comparison to some hard and soft metal ions. The electrodes were used as indicator electrodes in the potentiometric titration of silver ion and in the determination of Ag⁺ in photographic emulsion and radiographic and photographic films. Published in Russian in Elektrokhimiya, 2009, Vol. 45, No. 7, pp. 862–868. The article is published in the original.