Development and validation of a fully automated online-SPE–ESI–LC–MS/MS multi-residue method for the determination of different classes of pesticides in drinking,ground and surface water

The present work describes a fully automated method based on online solid phase extraction–liquid chromatography–tandem mass spectrometry for the determination of different classes of pesticides, including acidic and polar pesticides and six thiamethoxam metabolites. Sample preconcentration was performed by extracting 4 mL of the sample with a single styrene-divinylbenzene polymer. Elution of the compounds was done within the high performance liquid chromatography gradient and tandem mass spectrometry determination was performed in the selected reaction monitoring mode, by recording 1–3 transitions per compound. The overall pretreatment and analysis time per sample was less than 15 min. Method validation was performed in drinking, ground and surface water. For nearly all compounds a recovery between 70% and 120% could be achieved. The limit of detection ranges from 1.2 to 18 ng/L in drinking water and 3.0 to 23 ng/L in ground and surface water. The correlation coefficients for a calibration range of 0.05–2 µg/L are between 0.9915 and 0.9999. The limit of quantification (LOQ) for all compounds lies below the required limit of 0.1 µg/L, to fulfil the Council Directive 98/83/EC. Most of the compounds easily reach an LOQ below 0.05 µg/L.     

Application of Solid-Phase Microextraction for the Determination of Organonitrogen Pesticides in Aqueous Samples by Gas Chromatography with Nitrogen-Phosphorus Detector

A method based on solid-phase microextraction and gas chromatography nitrogen-phosphorus detector for the determination of common organonitrogen pesticides (ONPs) in aqueous samples was described. Three kinds of commercially available coated fused-silica fibres were compared: 100 µm PDMS, 85 µm PA, and 65 µm CW-DVB; 65 µm CW-DVB was the most sensitive fibre coating for the analytes' determination. The extraction time, the stirring, the content of salt, and the content of organic solvents were found to have a significant influence on extraction efficiency. The optimised conditions were 65 µm CW-DVB fibre, 40 min extraction time, with rapid stirring and concentration of NaCl was fixed at 0.25 g/mL. The linear range was 0.1-100 µg/L for most of the compounds. The limits of detection (LODs) ranged from 0.02 mg/L (for trifluralin, simazine, terbuthylazine, cyanazine, and pendimethalin) to 0.08 µg/L (for terbutryn) and RSD % of repeatability were for most of the compounds below 10%. Thus the maximum level set by the European Union for pesticides and drinking waters can be verified. The recovery of spiked water samples was compared and validated with the liquid-liquid extraction one. Environmental water samples were analysed and trifluraline was detected.     

Leaching of Pesticides from Fields with Recorded Pesticide Applications

During two winter seasons, 1998/99 and 1999/2000, drainage water was sampled each fortnight from four fields with recorded pesticide application. Water was analysed for a range of pesticides used on the fields. Two of the four fields were equipped with three vertical stainless steel tubes with screens at 1-1.3 m depths. Two other fields were equipped with traditional tile drains, which solely drained the specific fields. Isoproturon, which was banned from use after 1999, was the most frequently found pesticide in the drainage water. Pendimethalin was another compound frequently found, however in low concentrations. In drainage water from a field at Silstrup the active ingredients bentazone and propyzamide appeared in the drainage water at the first sampling following treatment and during the following months. The highest concentration levels were 1.3 and 2.8 µg/L, respectively. Phenoxyacid herbicides, which had been detected at concentration levels up to 0.34 µg/L in an earlier study 10 years ago, no longer appeared in the drainage water.     

Sensitive determination of Fenamiphos in water samples by flow injection photoinduced chemiluminescence

In this work, a sensitive flow injection chemiluminescence (FI-CL) method for the determination of nematicide Fenamiphos in a rapid and simple way is proposed. Fenamiphos is first photodegraded in basic medium. These photofragments react with Ce(IV) providing the chemiluminescence signal. To the authors’ knowledge, no chemiluminescence method has been described in the literature for the determination of the nematicide Fenamiphos. All physical and chemical parameters in the flow injection chemiluminescence system were optimized in order to obtain the best sensitivity, selectivity and sample throughput. Before the injection of the sample in the FI-CL system, a preconcentration step with solid phase extraction C18 cartridges was performed. By applying solid phase extraction (SPE) to 250?mL of standard (final volume 10?mL), the linear dynamic range was between 3.4 and 60?µg?L^?1, and the detection limit was 1?µg?L^?1. When SPE was applied to 500?mL of standard (final volume 10?mL), the detection limit was 0.5?µg?L^?1. These detection limits are below the emission limit value established by the Spanish Regulations of the Hydraulic Public Domain for pesticides (50?µg?L^?1) and of the same order as the limit established for total pesticides (0.5?µg?L^?1) at European Directive on the quality of water for human consumption. The sample throughput was 126 hour^?1. Intraday and interday coefficients of variation were below 10% in all cases. No interference was registered in presence of usual concentrations of anions, cations and other organophosphorus pesticides. The method was successfully applied to the analysis of environmental water samples, obtaining recoveries between 96 and 107.5%.     

A microconductometric biosensor based on lipase extracted from Candida rugosa for direct and rapid detection of organophosphate pesticides

Organophosphate pesticides (OPs) have been intensively used as insecticides in agriculture; after entering the aquatic environment, they may affect a wide range of organisms. A conductometric enzymatic biosensor based on lipase extracted from Candida rugosa (CRL) has therefore been developed for the direct and rapid quantitative detection of organophosphate pesticides: diazinon, methyl parathion and methyl paraoxon in water. The biosensor signal and response time were obtained under optimum conditions, the enzyme being immobilised in the presence of gold nanoparticles. Under these conditions, the enzymatic biosensor was able to measure concentrations as low as 60 µg/L of diazinon, 26 µg/L of methyl parathion and 25 µg/L of methyl paraoxon very rapidly (response time: 3 min). Moreover, this CRL biosensor was not sensitive to interferences such as carbamates. It presented good storage stability for 21 days when kept at 4°C and it was successfully applied to real samples.     

Gas chromatographic–mass spectrometric methodology using solid-phase microextraction for the multiresidue determination of pesticides in surface waters

Solid-phase microextraction (SPME) coupled with gas chromatography–mass spectrometry (GC–MS) and selected ion monitoring (SIM) was used for the analytical determination of priority pesticide residues. Fibers coated with a 65-µm film thickness of polydimethylsiloxane divinylbenzene (PDMS-DVB) were used to extract 31 pesticides of different chemical groups. The quality parameters of the method demonstrated a good precision with detection limits of 1–56?ng/L. Linearity was controlled in the range of 0.1–50?µg/L. The proposed method was applied for the trace-level determination of the target pesticides in surface water samples including three rivers and one lake at the Epirus region (north-west Greece) for a period of one year. The results demonstrate the suitability of the SPME–GC–MS approach for the analysis of multi-residue pesticides in environmental water samples.     

Analysis of parabens in dentifrices and the oral cavity

This study analyzed levels of parabens in commercial dentifrices and saliva. HPLC was performed using 35% acetonitrile and measuring absorbance at 254 nm. Thirteen toothpastes and five mouthwashes were analyzed. Of these, volunteers used three toothpastes and two mouthwashes, and levels of parabens were analyzed in saliva and water used for mouth rinsing. In toothpastes, the highest concentrations of methylparaben (MP), propylparaben (PP) and n‐butylparaben (nBP) were 1.86, 1.42 and 1.87 mg/g, respectively. In mouthwashes, the highest concentrations of MP and PP were 0.97 and 0.11 mg/mL, respectively. After volunteers used 500 mg toothpaste T‐1, which contained 895 µg MP, the first and tenth mouth rinse samples contained means of 64.63 and 1.89 µg MP, respectively. After rinsing the mouth three or five times, 37 µg or 18 µg MP was calculated to remain in the oral cavity, respectively. After using 20 mL mouthwash S‐1, which contained 19 mg MP, 1.53 mg MP was calculated to remain in the oral cavity. Immediately after using this mouthwash, the mean salivary concentration of MP was 237 µg/mL. The daily intake of parabens from dentifrices was predicted to be insignificant compared with the intake from food; however, parabens can be ingested from dentifrices. Copyright © 2014 John Wiley & Sons, Ltd.     

Dispersive liquid–liquid microextraction followed by high-performance liquid chromatography for the determination of three carbamate pesticides in water samples

A simple, rapid and efficient method, dispersive liquid–liquid microextraction (DLLME) in conjunction with high-performance liquid chromatography (HPLC), has been developed for the determination of three carbamate pesticides (methomyl, carbofuran and carbaryl) in water samples. In this extraction process, a mixture of 35 µL chlorobenzene (extraction solvent) and 1.0 mL acetonitrile (disperser solvent) was rapidly injected into the 5.0 mL aqueous sample containing the analytes. After centrifuging (5 min at 4000 rpm), the fine droplets of chlorobenzene were sedimented in the bottom of the conical test tube. Sedimented phase (20 µL) was injected into the HPLC for analysis. Some important parameters, such as kind and volume of extraction and disperser solvent, extraction time and salt addition were investigated and optimised. Under the optimum extraction condition, the enrichment factors and extraction recoveries ranged from 148% to 189% and 74.2% to 94.4%, respectively. The methods yielded a linear range in the concentration from 1 to 1000 µg L^?1 for carbofuran and carbaryl, 5 to 1000 µg L^?1 for methomyl, and the limits of detection were 0.5, 0.9 and 0.1 µg L^?1, respectively. The relative standard deviations (RSD) for the extraction of 500 µg L^?1 carbamate pesticides were in the range of 1.8–4.6% (n = 6). This method could be successfully applied for the determination of carbamate pesticides in tap water, river water and rain water.     

Use of SPME extraction to determine organophosphorus pesticides adsorption phenomena in water and soil matrices

Solid-phase micro extraction (SPME) coupled with GC enables rapid and simple analysis of organophosphorus pesticides in a range of complex matrices. Investigations were made into the extraction efficiencies from water of six organophosphorus insecticides (methamidophos, omethoate, dimethoate, parathion methyl, malathion, and parathion ethyl) showing a wide range of polarities. Three SPME fibres coated with different stationary phases, polydimethylsiloxane, polyacrylate, and carbowax-divinylbenzene (CW-DVB), were investigated. Water was spiked with the pesticides at concentrations from 1 to 0.01 µg mL-1, and the solutions used for optimization of the procedure. The CW-DVB fibre, with a 65 µm coating, gave the best performance. The optimized experimental conditions were sample volume 10 mL at 20°C, equilibration time 16 min, pH 5, and presence of 10% w/v NaCl. SPME analyses were performed on solutions obtained by equilibrating aqueous pesticide solutions with six certified soils with various physico-chemical characteristics. SPME data were also assessed by comparison with analyses performed by using conventional solid-phase extraction. Results indicate the suitability of SPME for analysis of pesticides in environmental water samples.     

Characterization of Carbamate Pesticides in Natural Water from Cameroon

With the increased use of chemicals in agriculture for crop protection and improvement of yield, the contamination of water is currently a serious health concern. This study used solid-phase extraction with ultra-high-performance liquid chromatography–tandem mass spectrometry to evaluate the presence of 23 carbamate pesticides in waters from Cameroon. The separation was achieved in 5.5?min using a C₁₈ column (50?×?2.1?mm, 1.8?µm) with a mobile phase composed of water and methanol each containing 0.01% formic acid. The analytes were determined in positive multiple reaction monitoring mode. The recoveries for fortified water were from 75 to 99%, with relative standard deviations below 13%. The limits of detection ranged from 0.003 to 0.397?µg?L^?1. The reported method is simple, sensitive, and accurate, and is a suitable alternative for routine monitoring of pesticide residues at ultra-trace levels. The analysis revealed the presence of propoxur at a concentration of 0.072?µg?L^?1 in stream water.     

Uranium in ground water of Rajnandgaon District of Central India

The present study highlights uranium levels, associated health effects, and physicochemical properties of ground water samples collected from Rajnandgaon District of Chhattisgarh State, Central India. Uranium concentrations of ground water samples are found to exceed than 30 µg/L (United States Environmental Protection Agency and World Health Organisation recommended limit) at two villages in summer and at one village in winter while it is found higher than 60 µg/L (Atomic Energy Regulatory Board, Department of Atomic Energy, India recommended limit) at only one village in summer. Correlation analysis between uranium and physicochemical parameters suggest that Ca²⁺ ion and total alkalinity play an important role in uranium contamination of ground water.

     

Accurate mass measurement in nano-electrospray ionization mass spectrometry by alternate switching of high voltage between sample and reference sprayers

An electrospray dual sprayer, which generates separate sample and reference sprays by alternately switching the high voltage between the two sprayers, is described. The technique permits accurate mass measurements in nano-electrospray ionization mass spectrometry (ESI-MS) to be obtained using a quadrupole/orthogonal acceleration time-of-flight mass spectrometer (Q-TOF). Similar to the method employed with a dual ESI source (Wolff JC et al., Anal. Chem. 2001; 73: 2605), the two sprays are orthogonal with respect to each other, but can be independently sampled without any baffle between these sprays. The reference sprayer is used in the original configuration of the ESI source and was optimized for a 1-2 muL/min flow, whereas the sample sprayer can be either a conventional glass capillary or a borosilicate tip of the type used for nano-ESI. Both sprayers can be positioned close to the cone so as to give maximum ion currents. The sample and reference sprays are independently generated by raising the potentials on the sample and reference sprayers to 1.4 and 3.0 kV, respectively; the high voltages can be rapidly turned on and off in ca. 1 ms. A nano-ESI-MS or nano-flow LC/ESI-MS experiment using a Q-TOF coupled with the above system gave mass accuracies within 3 ppm for measurements of ions up to m/z 1000 using subpicomole samples.     

Determination of Triazines and N-Methylcarbamate Pesticides in Water by High-Performance Liquid Chromatography-Diode Array Detection

A rapid and selective method for the simultaneous determination of triazine herbicides (atrazine, its degradation product desethylatrazine, simazine, prometryn, terbutryn) and N-methylcarbamate insecticides (propoxur, carbaryl and methiocarb) in surface water has been developed. A 0.5 L of the water sample was preconcentrated by passage through a 1 g C₁₈ solid-phase extraction cartridge. The retained compounds were eluted with 5 mL of methanol from the cartridge. The pesticides were separated and quantified by reversed-phase high-performance liquid chromatography with UV diode-array detection. Analytical separation was performed using a concave gradient elution with acetonitrile and water on a C₁₈ column. Prometryn and terbutryn were determined at 240 nm; propoxur, methiocarb at 204 nm and the others at 220 nm. Recoveries varied from 85 to 102% over concentrations at 0.025 and 0.2 µg L^?1. The limits of detection for the compounds investigated are in the range of 0.005-0.012 µg L^?1.     

Salt‐assisted acetonitrile extraction and HPLC‐QTOF‐MS/MS detection for residues of multiple classes of pesticides in human serum samples

Detecting pesticide residues in human serum is a challenging process. In this study we developed and validated a method for the extraction and recovery of residues of multiple classes of pesticides from serum using one reagent. Salt‐assisted acetonitrile extraction and high‐performance liquid chromatography with quadrupole time of flight tandem mass spectrometry were used to quantitate 34 pesticides classified in nine groups of chemicals in human serum samples, which are frequently detected in food. The recoveries for 33 of analyzed pesticides ranged from 86 to 112% with relative standard deviations below 15%. The limits of quantitation and linearity of 31 of the pesticides were 1 µg/L and >0.990, respectively. The lower limit of quantitation has been reported in the literature particularly for multi‐classes pesticide mixtures in human serum. The salt–acetonitrile reagent was allowed to achieve good recoveries and detection limits, which could be attributed to salt altering the solvent polarity, preferentially collecting the organic phase in the solution, and promoting the extraction. The developed method was applied for two organophosphate pesticide metabolites, diethylphosphate and 3,5,6‐trichloro‐2‐pyridinol, in serum from rats that were fed a nonlethal quantity of chlorpyrifos. The concentrations of these two were 252.18 ± 15.47 and 0.63 ± 0.23 µg/L, respectively.     

Multiresidue fully automated online SPE-HPLC-MS/MS method for the quantification of endocrine-disrupting and pharmaceutical compounds at trace level in surface water

The present work describes the development and validation of a sensitive method for the determination of traces of diverse groups of pharmaceuticals and endocrine disruptors in surface water. Thirty-seven substances have been selected, including 10 pesticides, 6 hormonal steroids and assimilates, 12 pharmaceuticals, 5 alkylphenols, 1 chlorophenol and 3 other well-known human contaminants, 1 UV filter and 2 plasticisers. An automated online solid-phase extraction (SPE) is directly coupled to liquid chromatography–tandem mass spectrometry. Different SPE columns have been tested, and the injection volume has been optimised. The developed analytical methodology is based on the direct injection of 2.5 mL of water sample acidified at pH 1.6 on an Oasis HLB loading column (20 × 2.1 mm) with 5-µm particles. Then, the chromatographic separation is achieved on a Kinetex XB C18 (100 × 2.1 mm; 1.7 µm) column, and the quantification is realised in multiple-reaction monitoring mode. The online SPE step warrants minimal sample handling, low solvent consumption, high sample throughput, saving time and costs. This method allows the quantification of the target analytes in the lower ng/L concentration range, with limits of quantification (LQs) between 100 pg/L and 10 ng/L, 26 compounds having LQ lower than 1 ng/L. The monitoring of two selected MS/MS transitions for each compound allows the reliable confirmation of positive findings even at the LQ level. The developed and validated methodology has been applied to the analysis of various real samples from two French rivers. Twelve target compounds have been detected in the environmental samples, and the major pollutants are pharmaceuticals usually used by humans (paracetamol, carbamazepine, oxazepam, ketoprofen, trimethoprim). The pesticides atrazine and carbendazim have been ubiquitously detected in real samples too. Metronidazole, sulfamethoxazole and diuron were also frequently quantified in the water samples.     

Multiresidue Method for the Determination of Organophosphorus Pesticides in Still Wine and Fortified Wine Using Solid-Phase Microextraction and Gas Chromatography – Tandem Mass Spectrometry

A SPME-GC-MS/MS method for the determination of eight organophosphorus pesticides (azinphos-methyl, chlorpyriphos, chlorpyriphos-methyl, diazinon, fenitrothion, fenthion, malathion, and methidathion) in still and fortified wine was developed. The extraction procedure is simple, solvent free, and without any sample pretreatment. Limits of detection (LOD) and quantitation (LOQ) values in the range 0.1–14.3 µg/L and 0.2–43.3 µg/L, respectively, were obtained. The LOQ values are below the maximum residue levels (MRLs) established by European Regulation for grapes, with the exception of methidathion. Coefficients of correlation (R²) higher than 0.99 were obtained for the majority of the pesticides, in all different wines analyzed.     

Multiresidue GC-MS/MS pesticide analysis for evaluation of tea and herbal infusion safety

ABSTRACT

A fast, simple, low-cost and high-throughput multiresidue pesticide analysis method was developed and validated for 300 pesticides in herbal and fruit infusion samples based on modified QuEChERS (quick, easy, cheap, effective, rugged and safe) procedure combined with gas chromatography coupled with tandem mass spectrometry method (GC-MS/MS). The objectives were to develop low cost GC-MS/MS method, validate the method in accordance to SANTE/11,813/2017 guidance document and application in routine. The results obtained using different GC and MS/MS parameters were evaluated in order to develop quick, robust, accurate and effective multiresidue method. Total analysis time was 28 min with 0.6 µL injection volume. For accurate quantification, matrix-matched calibration (MMC) curves (in range of 10 µg/kg – 250 µg/kg) were applied to compensate matrix effect. The limits of quantification (LOQ) were ranged between 0.06 µg/kg and 135 µg/kg, and for the majority of the pesticides the LOQ were below the regulatory maximum residue limits. Most recoveries at 10 µg/kg and 100 µg/kg were in the range 70%–120% indicating satisfactory accuracy. The validated method was applied to commercial herbal and fruit infusion products detecting chlorpyriphos, DEET, tebuconazole, terbuthylazine, piperonyl butoxide, biphenyl, pendimethalin, pirimiphos-methyl and p,p’-DDE in more than 100 samples from 1,466 so risk assessment on human health was calculated specially for those pesticides.     

Development and validation of a SPE-GC-MS method for the determination of pesticides in surface water

A method for analysis of 20 commonly used pesticides in surface water based on solid-phase extraction and gas chromatography-mass spectrometry was proposed. During method development the key parameters that can affect SPE extraction and determination such as selection of efficient SPE sorbent, pH of water sample, type and volume of elution solvent, breakthrough volume and matrix effects were investigated. The method was validated using spring water spiked with appropriate concentration of pesticides. The obtained correlation coefficients were in range 0.9972–1.000, limits of detection (LOD) were 0.001–0.5?µg?L^?1 and the limits of quantification (LOQ) were 0.005–1?µg?L^?1 depending on a pesticide. Much higher LOD (20?µg?L^?1) and LOQ (50?µg?L^?1) values were obtained for bentazone. The influence of matrix was assessed using real water samples spiked with appropriate concentration of pesticide standards solution. Both signal enhancement and suppression were observed, depending on a pesticide, therefore standard addition method was used for pesticides determination. The developed method was applied on real water samples taken in close vicinity of agricultural fields. Many of the targeted pesticides were found in the samples and the results are presented in this article.     

Determination of Pesticides in the Rhizome of Traditional Chinese Medicines by Gas Chromatography with Electron Capture Detection

A simple and efficient gas chromatography method for the determination of 27 organochlorine and pyrethroid pesticides in traditional Chinese medicine was developed. Pesticide residues were extracted from the samples by oscillation and ultrasound, and purified by gel permeation chromatography and florisil solid phase extraction. The analysis was performed by gas chromatography with micro-electron capture detection. The purification conditions, such as the extraction and elution solvents, extraction methodology, and gel permeation chromatography conditions, were optimized. Traditional Chinese medicines were purified by different methods based on their composition. Under optimized conditions, the calibration graph was linear from 10 to 500 µg/L and the correlation coefficients varied from 0.9958 to 0.9997. The detection limits of these pesticides were between 0.09 and 1.82 µg/kg. The recovery of the pesticides spiked in various samples at four concentrations ranged from 73.2% to 106.4%, with relative standard deviations between 1.0% and 14.0%. This study indicates that the method is useful for determining pesticides in rhizome traditional Chinese medicines.     

Bismuth Film Electrodes for Adsorptive Stripping Voltammetric Determination of Sunset Yellow FCF in Soft Drinks

The bismuth film electrode was used to record well‐developed voltammograms of azo food coloring Sunset Yellow FCF (SY). The employed Bi(III)/HClO₄ plating solutions produced very adhesive and mechanically stable films that were applied in both stationary and flow conditions. The influence of the dimensions of the glassy carbon support, plating solution concentration and potential was discussed. The sensitivity of SWV was sufficient to obtain a linear calibration curve for low concentration levels of SY (below 0.1 mg/L; LOD=1 µg/L, linear range 4.4–87 µg/L). The measurements in a flow system were considered as a tool for the determination of relatively high concentrations (>1 mg/L; LOD=300 µg/L, linear range 300–8800 µg/L) of SY.