Flame atomic absorption spectrometric determination of μg amounts of Fe (III) ions after solid phase extraction using modified octadecyl silica membrane disks

A simple, rapid and reliable method has been developed to selectively separate and concentrate ultra trace amounts of Fe (III) ions from aqueous samples for the measurement by flame atomic absorption spectrometry (FAAS). By the passage of aqueous samples through an octadecyl silica membrane disk modified by a recently synthesized Schiff base (Bis-(4-nitro phenyl azo) salisilidine-1,3-diamino propane), Fe(III) ions adsorb quantitatively and most of matrix elements will pass through the disk to drain. The retained iron ions are then stripped from the disk by minimal amount of 0.1 mol l^− 1 sulfuric acid as eluent. Extraction efficiency and the influence of pH, flow rates, amount of ligand, type and least amount of stripping acid as eluent were evaluated. The recovery of the iron from aqueous solution on the membrane disk modified with 3 mg Schiff's base was quantitative over pH 2–4.5.     

Ultratrace determination of lead,cadmium and copper in environmental and biological samples by atomic absorption spectrometry after their separation and preconcentration using octadecyl silica membrane disks modified with a new n–s schiff base

Pb(II), Cd(II) and Cu(II) ions were separated and preconcentrated by solid-phase extraction on octadecyl-bonded silica membrane disks modified with a new S–N-containing Schiff base (bis-2-thiophenal propandiamine) (BTPD) followed by elution and atomic absorption spectrometric detection. The method was applied as a separation and detection method for lead(II), cadmium(II) and copper(II) in environmental and biological samples. Extraction efficiency and the influence of sample matrix, flow rate, pH, and type and minimum amount of stripping acid were investigated. The maximum capacity of the membrane disks modified by 4?mg of BTPD was found to be 668 ± 10, 480 ± 8 and 454 ± 7?µg of lead, cadmium and copper, respectively. The limit of detection of the proposed method is 0.25, 0.01 and 0.02?ng/mL for lead, cadmium and copper, respectively.     

Pre-concentration of ultra trace amounts of copper,zinc, cobalt and nickel in environmental water samples using modified C18 extraction disks and determination by inductively coupled plasma–optical emission spectrometry

A highly sensitive and accurate method for pre-concentration and determination of ultra trace amounts of zinc, copper, cobalt and nickel ions in environmental water samples is proposed. The method is based on the solid phase extraction of these ions on C18-bonded silica extraction disks modified with a novel Schiff base 2,2′-[1,6-hexanediyl bis (nitriloethylidine)]bis-1-naphthol (HDN). The retained ions on the prepared solid phase was eluted with 10 mL 0.01 M nitric acid and measured by inductively coupled plasma–optical emission spectrometry. The extraction efficiency and the influence of the type and least amount of eluent for the stripping of ions from the disks, pH, flow rates of sample solution and eluent, amount of HDN, effect of other ions and breakthrough volume were evaluated. The limits of detection of the method were 0.2, 0.2, 0.8 and 0.6 µg L^?1 for zinc, copper, cobalt and nickel, respectively and an enrichment factor of 100 was obtained. The proposed method was applied for determination of zinc, copper, cobalt and nickel ions in some natural and synthetic water samples with satisfactory results.     

Solidified floating organic drop microextraction–electrothermal atomic absorption spectrometry for ultra trace determination of antimony species in tea, basil and water samples

Solidified floating organic drop microextraction was applied as a separation/preconcentration step prior to the electrothermal atomic absorption spectrometric (ETAAS) determination of ultra trace of antimony species. The method was based on the formation of an extractable complex between Sb(III) and ammonium pyrrolidinedithiocarbamate at pH ~ 5, while Sb(V) was remained in the aqueous phase. The antimony extracted into 1-undecanol was determined by ETAAS. Total antimony was determined after the reduction of Sb(V) to Sb(III) with potassium iodide and ascorbic acid. The amount of Sb(V) was determined from the difference of concentration of total antimony and Sb(III). Under the optimum conditions an enhancement factor of 437.5 and a detection limit of 5.0 ng L^?1for the preconcentration of 25 mL of sample was achieved. The relative standard deviation at 300 ng L^?1 of antimony was found to be 3.5 % (n = 6). The proposed method was successfully applied to the determination of antimony in tea, basil and natural water samples.     

Determination of ultra traces of lead in water samples after combined solid-phase extraction–dispersive liquid–liquid microextraction by graphite furnace atomic absorption spectrometry

A solid-phase extraction coupled with dispersive liquid–liquid microextraction (DLLME) method followed by graphite furnace atomic absorption spectrometry (GFAAS) was developed for the extraction, preconcentration, and determination of ultra trace amounts of lead in water samples. Variables affecting the performance of both steps were thoroughly investigated. Under optimized conditions, 100 mL of lead solution were first concentrated using a solid phase sorbent. The extracts were collected in 1.50 mL of THF and 18 μL of carbon tetrachloride was dissolved in the collecting solvent. Then 5.0 mL pure water was injected rapidly into the mixture of THF and carbon tetrachloride for DLLME, followed by GFAAS determination of lead. The analytical figures of merit of method developed were determined. With an enrichment factor of 1,800, a linear calibration of 3–60 ng L^?1 and a limit of detection of 1.0 ng L^?1 were obtained. The relative standard deviation for seven replicate measurements of 30 ng L^?1 of lead was 5.2 %. The relative recoveries of lead in mineral, tap, well, and river water samples at spiking level of 10 and 20 ng L^?1 are in the range 94–106 %.     

Ionic liquid ultrasound assisted dispersive liquid–liquid/micro-volume back extraction procedure for preconcentration and determination of ultra trace amounts of thallium in water and biological samples

A simple, highly sensitive and environment-friendly method, combined with flame atomic absorption spectroscopy (FAAS) is developed to preconcentrate and determine trace amounts of thallium in aqueous solutions. In the preconcentration step, the thallium (I) from 30?mL of an aqueous solution was extracted into 350?µL of ionic liquid, 1-hexyl-3-methylimidazolium hexa?uorophosphate [Hmim][PF₆], containing dicyclohexyl-18-crown-6 (DCH-18-crown-6) as complexing agent. Subsequently, the DCH-18-crown-6 complex was back-extracted into 300?µL of nitric acid (2?mol?L^?1) solution, and analyzed by FAAS. Several parameters in?uencing the extraction and determination of thallium, such as pH, concentration of DCH-18-crown-6, sonication and centrifugation times, sample volume, ionic liquid amounts, ionic strength, and concentration of stripping acid solution, were optimized. Under optimum conditions, the calibration graph was linear in the range of 5 to 400?ng?mL^?1, the detection limit was 0.64?ng?mL^?1 (3S_b/m, n?=?7), the enhancement factor was 98.2 and the relative standard deviation was ±1.43%. The results for preconcentration and determination of trace amount of thallium in waste water, well water, tap water, sea water, human hair and nail demonstrated the accuracy, recovery and applicability of the presented method.     

Tandem dispersive liquid–liquid microextraction coupled with micro-sampling flame atomic absorption spectrometry for rapid determination of lead(II) and cadmium(II) ions in environmental water samples

ABSTRACT

Tandem dispersive liquid liquid microextraction coupled with micro - sampling flame atomic absorption spectrometry for rapid determination of lead2 and cadmium2 ions in environmental water samples. A simple method termed as tandem dispersive liquid–liquid microextraction coupled with micro-sampling flame atomic absorption spectrometry is used for determination of the lead(II) and cadmium(II) ions in different environmental water samples. According to the proposed method, the target analytes are extracted from an aqueous sample solution (10 mL) into a micro-volume of an organic solvent, and then they are selectively back-extracted into an aqueous acceptor solution (150 μL) to increase the compatibility of the extractant phase with a final analyser system and provide a suitable enrichment factor. The developed method is very fast, implemented in just about 7 min, and provides a high sample clean-up. The factors influencing the extraction efficiency including the type and volume of the organic solvent, pH and volume of the acceptor solution, and number of extractions are thoroughly examined and optimised. Under the optimal experimental conditions, the developed method provides a good linearity (in the range of 0.4–300 ng mL^?1 (R² ≥ 0.994)), and low limits of detection (in the range of 0.07–0.31 ng mL^?1). Finally, the method is successfully applied for the direct determination of the understudied analytes in the river, dam, and well water samples.     

Application of microwave-assisted dispersive liquid–liquid microextraction and graphite furnace atomic absorption spectrometry for ultra-trace determination of lead and cadmium in cereals and agricultural products

This study was designed to determine the ultra-trace amounts of lead (Pb) and cadmium (Cd) in various cereals (rice, wheat, barley, peas, beans, corn and lentil) obtained from the markets in Kermanshah city, West Iran. An efficient microextraction method was applied to separation and preconcentration of metal ions. This method is dispersive liquid–liquid microextraction based on solidification of floating organic drop, which overcomes the most important problems of other microextraction techniques. Some effective parameters on extraction were studied and, under optimised conditions, the enhancement factors were 122 and 115 for Cd and Pb, respectively. The calibration graphs were linear in the range of 0.1–50 µg kg^?1 with correlation coefficient more than 0.992. The detection limit was 0.05 µg kg^?1. The values of intra-day relative standard deviations and inter-day relative standard deviations were in the range of 4.7?5.3% and 6.0?6.8%, respectively. The Pb concentrations in rice and wheat samples were considerably higher than the allowable limits set by World Health Organization. The method was successfully applied to determination of the Pb and Cd in cereals, and application of the proposed method to the analysis of two certified reference materials produced results that were in good agreement with the certified values.     

Speciation of chromium in water samples using dispersive liquid–liquid microextraction and flame atomic absorption spectrometry

A novel method for preconcentration is described for chromium speciation at microgram per liter to sub-microgram per liter levels. It is based on selective complex formation of both Cr(VI) and Cr(III) followed by dispersive liquid–liquid microextraction and determination by microsample introduction-flame atomic absorption spectrometry. Effects influencing complex formation and extraction (such as pH, temperature, time, solvent, salinity and the amount of chelating agent) have been optimized. Enrichment factors up to 275 and 262 were obtained for Cr(VI) and total Cr, respectively. The calibration graph is linear from 0.3 to 20 µg L^?1, and detection limits are 0.07 and 0.08 µg L^?1 for Cr(VI) and total Cr, respectively. Relative standard deviations (RSDs) were obtained to be 2.0% for Cr(VI) and 2.6% for total Cr (n?=?7).     

Determination of trace amounts of chlorobenzenes in water using membrane-supported headspace single-drop microextraction and gas chromatography–mass spectrometry

A novel method based on the coupling of membrane-supported headspace single-drop microextraction with gas chromatography?mass spectrometry (GC–MS) is developed for the determination of chlorobenzenes in water samples. For the determination of five chlorobenzenes, a 15 μL toluene microdrop was placed inside the plastic membrane and exposed for 10 min for headspace extraction while stirring at 1000 rpm. The microdrop was then picked up by a microsyringe and directly injected into the injector block of the GC–MS instrument. Under the optimized operation conditions, the calculated calibration curves gave a high level of linearity for all targets with correlation coefficients range from 0.9945 to 0.9987. The limits of detection range from 0.01 to 0.05 μg/L and the RSDs for most of chlorobenzenes were below 7%. The method is simple, sensitive, and stable for single drop microextraction. Its applicability is demonstrated by the determination of chlorobenzenes in tap water samples.     

Speciation of very low amounts of arsenic and antimony in waters using dispersive liquid–liquid microextraction and electrothermal atomic absorption spectrometry

A new procedure for the determination of inorganic arsenic (III,V) and antimony (III,V) in water samples by dispersive liquid–liquid micro extraction separation and electrothermal atomic absorption spectrometry (ETAAS) is presented. At pH 1, As(III) and Sb(III) are complexed with ammonium pyrrolidine dithiocarbamate and extracted into the fine droplets formed when mixing carbon tetrachloride (extraction solvent), methanol (disperser solvent) and the sample solution. After extraction, the phases are separated by centrifugation, and As(III) and Sb(III) are determined in the organic phase. As(V) and Sb(V) remain in the aqueous layer. Total inorganic As and Sb are determined after the reduction of the pentavalent forms with sodium thiosulphate. As(V) and Sb(V) are calculated by difference. The detection limits are 0.01 and 0.05 µg L^− 1 for As(III) and Sb(III), respectively, with an enrichment factor of 115. The relative standard deviation is in the 2.9–4.5% range. The procedure has been applied to the speciation of inorganic As and Sb in bottled, tap and sea water samples with satisfactory results.     

Trace determination of cadmium in rice samples using solidified floating organic drop microextraction based on vesicular supramolecular solvent followed by flow-injection analysis–flame atomic absorption spectrometry

In this work, a solidified floating organic drop microextraction was developed based on a vesicular supramolecular solvent consisting of decanoic acid and quaternary ammonium. The method was used for preconcentration of trace amount of cadmium in different rice samples followed by flow-injection analysis–flame atomic absorption spectrometry. Several parameters affecting the extraction efficiency including pH, concentration of 1-(2-pyridylazo)-2-naphthol as the chelating agent, sample and extraction solvent volume, stirring rate, extraction time, salt effect, and interfering ions were investigated and optimized. Under the optimum conditions, a preconcentration factor of 84 was achieved. LOD and LOQ were found to be 0.09 and 0.31 µg L^?1, respectively. The calibration curve was linear within the range of 5.0–700 µg L^?1 (r²?>?0.9978). Intra- and inter-day precisions (RSD% n?=?3) were estimated 2.7 and 3.9% at the concentration of 20 µg L^?1, respectively. The accuracy of the method was successfully validated by analysis of an SRM-1643f standard reference material. Relative recoveries were achieved within the range of 93–107% elucidating suitability of the method for determination of cadmium in rice samples.     

Separation and determination of trace inorganic germanium in β-carboxyethylgermanium sesquioxide by filtration chromatography and hydride generation-graphite furnace atomic absorption spectrometry

A method has been proposed for the determination of trace (ng) inorganic germanium in β-carboxyethylgermanium sesquioxide (Ge-132) using hydride generation-graphite furnace AAS taking the advantage that Ge-132 was in the form that did not generate volatile hydride upon reduction. The analytical results obtained for Ge were checked by that obtained after separation from Ge-132 using filtration chromatography on a cation exchange column. The method was applied to the analysis of Ge-132 oral nutrition liquor; less than μgml⁻¹ of inorganic Ge in Ge-132 can be determined.     

Slurry sampling for the determination of arsenic, cadmium, and lead in mainstream cigarette smoke condensate by graphite furnace–atomic absorption spectrometry and inductively coupled plasma–mass spectrometry

The slurry sampling technique has been applied for the determination of As, Cd, and Pb in mainstream cigarette smoke condensate (MS CSC) by graphite furnace-atomic absorption spectrometry (GF-AAS) and inductively coupled plasma-mass spectrometry (ICP-MS). The MS CSC of the 1R4F Reference Cigarette was collected by electrostatic precipitation and was subsequently prepared as two slurry samples with and without the dispersing agent Triton X-100. Comparison of results determined by ICP-MS analyses of the 1R4F MS CSC slurry samples with those from the conventional microwave digestion method revealed good agreement. The precision of Triton X-100 slurry sampling and of microwave-assisted digestion was better than 10% RSD, and both were superior to slurry sampling without use of Triton X-100. The accuracy of the analytical results for the Triton X-100 slurry sample was further verified by graphite furnace-atomic absorption spectrometry (GF-AAS). For GF-AAS, the method limits of detection are 1.6, 0.04, and 0.5 microg x L(-1) for As, Cd, and Pb, respectively. For ICP-MS, the method limits of detection are 0.06, 0.01, and 0.38 microg x L(-1) for As, Cd, and Pb, respectively. The MS CSC of the 1R4F Reference Cigarette was collected in accordance with the Federal Trade Commission (FTC) smoking regime (35 mL puff volume of 2-s puff duration at an interval of 60 s) and the concentrations of As, Cd and Pb were 6.0+/-0.5, 69.3+/-2.8, and 42.0+/-2.1 ng/cigarette, respectively.     

Preconcentration and determination of low amounts of cobalt in black tea,paprika and marjoram using dispersive liquid–liquid microextraction and flame atomic absorption spectrometry

A dispersive liquid–liquid microextraction (DLLME) method for separation/preconcentration of ultra trace amounts of Co(II) and its determination with FAAS was developed. The DLLME behavior of Co(II) using Aliquat 336-chloride as ion pairing agent was systematically investigated. The factors influencing the ion pair formation and extraction by DLLME method were optimized. Under the optimized conditions for 150 µL of extraction solvent (carbon tetrachloride), 1.5 mL disperser solvent (acetonitrile) and 5 mL of sample, the enrichment factor was 30. The detection limit was 5.6 µg L^?1 and the RSD for replicate measurements of 1 mg L^?1 was 1.32 %. The calibration graph using the preconcentration system for cobalt was linear from 40 to 400 µg L^?1 with a correlation coefficient of 0.999. The proposed method was successfully applied for determination of cobalt in black tea, paprika and marjoram real samples.     

Dispersive liquid–liquid microextraction combined with flow injection inductively coupled plasma mass spectrometry for simultaneous determination of cadmium, lead and bismuth in water samples

Dispersive liquid–liquid microextraction (DLLME) was combined with flow injection inductively coupled plasma mass spectrometry for simultaneous determination of cadmium, lead and bismuth in water samples. The metal elements were complexed with sodium diethyldithiocarbamate, and then the complexes were extracted into carbon tetrachloride by using DLLME. Under the optimized conditions, the enrichment factors for Cd, Pb and Bi are 460, 900 and 645 in 5 mL of a spiked water sample, respectively. The calibration graphs for the three metals are linear in the range of concentrations from <10 ng L^?1 to 1,000 ng L^?1. The detection limits are 0.5 ng L^?1, 1.6 ng L^?1 and 4.7 ng L^?1, respectively. The relative standard deviations for ten replicate measurements of 50 ng L^?1 cadmium, lead and bismuth are 2.6%, 6.7%, and 4.9%, respectively, and the relative recoveries in various water samples at a spiking level of 50 ng L^?1 range from 83.6% to 107.0%.     

Ionic liquid-based dispersive liquid–liquid microextraction for determination of trace amounts of iron in water, rock and human blood serum samples

A green and sensitive dispersive liquid-phase microextraction procedure based on room-temperature ionic liquid (1-hexyl-3-methylimidazolium hexafluorophosphate) for preconcentration and determination of total iron in real samples prior to flame atomic absorption spectrometry was developed. 2-Mercaptopyridine-N-oxide (pyrithione) and ethanol were used as complexing agent and dispersive solvent in the proposed method, respectively. The factors influencing the extraction were optimized. Under optimum conditions, the enhancement factor of 15 was obtained from only 11.35 mL of aqueous phase. The linear dynamic range and the detection limit were 10.0–700 and 2.4 μg L^?1, respectively. The relative standard deviation (RSD) for ten replicate measurements of 500 μg L^?1 of iron is 3.1 %. The developed method has been successfully applied for the determination of iron in water samples, human blood serum and rock certified reference material with high efficiency.