Optical properties of hexagonal boron nitride thin films deposited by radio frequency bias magnetron sputtering

The optical properties of hexagonal boron nitride (h-BN) thin films were studied in this paper. The films were characterized by Fourier transform infrared spectroscopy, UV--visible transmittance and reflection spectra. h-BN thin films with a wide optical band gap E_g (5.86 eV for the as-deposited film and 5.97 eV for the annealed film) approaching h-BN single crystal were successfully prepared by radio frequency (RF) bias magnetron sputtering and post-deposition annealing at 970~K. The optical absorption behaviour of h-BN films accords with the typical optical absorption characteristics of amorphous materials when fitting is made by the Urbach tail model. The annealed film shows satisfactory structure stability. However, high temperature still has a significant effect on the optical absorption properties, refractive index n, and optical conductivity σ of h-BN thin films. The blue-shift of the optical absorption edge and the increase of E_g probably result from stress relaxation in the film under high temperatures. In addition, it is found that the refractive index clearly exhibits different trends in the visible and ultraviolet regions. Previous calculational results of optical conductivity of h-BN films are confirmed in our experimental results.     

Preparation of boron carbon nitride thin films by radio frequency magnetron sputtering

Boron carbon nitride films were deposited by radio frequency magnetron sputtering using a composite target consisting of h-BN and graphite in an Ar-N₂ gas mixture. The samples were characterized by X-ray diffraction, Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. The results suggest that the films are atomic-level hybrids composed of B, C and N atoms. The boron carbon nitride films prepared in the present experiment have a disordered structure. The sputtering power varied from 80 W to 130 W. This sputtering power was shown to have regular effect on the composition of boron carbon nitride films. The samples deposited at 80 W and 130 W are close to the stoichiometry of BC₃N. The sample deposited at 110 W is close to the stoichiometry of BCN. The samples deposited at 100 W and 120 W approach to BC₂N. It is very significant for us to synthesize boron carbon nitride compound with controllable composition by changing the sputtering power.     

The effect of hydrogen on copper nitride thin films deposited by magnetron sputtering

Copper nitride thin films were deposited on Si (1 0 0) wafers by reactive magnetron sputtering at various H₂/N₂ ratios. X-ray diffraction measurements show that the films are composed of Cu₃N crystallites with anti-ReO₃ structure and exhibit preferred orientation of [1 0 0] direction. Although the relative composition of the films has obviously changes with the H₂/N₂ ratios, the orientations of the films keep almost no changes. However, the grain size, lattice parameter and composition of the films are strongly dependent on the H₂/N₂ ratios. The copper nitride films prepared at 10% H₂/N₂ ratios show poor stability and large weight gain compared to the copper nitride films prepared at 0% H₂/N₂ ratios.     

GaN films deposited by middle-frequency magnetron sputtering

GaN films were deposited on Si (111) substrates by middle-frequency magnetron sputtering. X-ray diffraction revealed preferential GaN (0 0 0 2) orientation normal to the substrate surface for all the films deposited. The diffraction intensity and N contents were found to depend strongly on the total gas pressure. Good quality films were only obtained at pressures in the range of 0.4-1.0 Pa. Little diffraction of GaN (0 0 0 2) could be observed either at total pressures below 0.4 Pa or above 1.0 Pa. The GaN films produced under the optimized conditions have an N:Ga ratio of 1:1 as determined by energy-dispersive X-ray spectroscopy.     

Bioactive glass thin films deposited by magnetron sputtering technique: The role of working pressure

Bioglass coatings were prepared by radio frequency magnetron sputtering deposition at low temperature (150 °C) onto silicon substrates. The influence of argon pressure values used during deposition (0.2 Pa, 0.3 Pa and 0.4 Pa) on the short-range structure and biomineralization potential of the bioglass coatings was studied. The biomineralization capability was evaluated after 30 days of immersion in simulated body fluid. SEM-EDS, XRD and FTIR measurements were performed. The tests clearly showed strong biomineralization features for the bioglass films. The thickness of the chemically grown hydroxyapatite layers was more than twice greater for the BG films deposited at the highest working pressure, in comparison to those grown on the films obtained at lower working pressures. The paper attempts to explain this experimental fact based on structural and compositional considerations.     

Preparation and structural properties of thin carbon films by very-high-frequency magnetron sputtering

Growth and structural properties of thin a-C films prepared by the 60 MHz very-high-frequency(VHF) magnetron sputtering were investigated. The energy and flux of ions impinging the substrate were also analyzed. It is found that the thin a-C films prepared by the 60 MHz sputtering have a lower growth rate, a smooth surface, and more sp~3 contents.These features are related to the higher ion energy and the lower ions flux onto the substrate. Therefore, the 60 MHz VHF sputtering is more suitable for the preparation of thin a-C film with more sp~3 contents.     

利用等离子体辅助脉冲磁控溅射实现 多晶硅薄膜的低温沉积

本文报道了利用电感耦合等离子体辅助中频直流脉冲磁控溅射在温度300 ℃ 以下沉积氢化多晶硅薄膜的制备方法. 利用拉曼散射、X射线衍射、透射电子衍射和傅里叶红外光谱对多晶硅薄膜进行了表征. 详细研究了氢气在沉积过程中所起的作用, 并结合Langmuir探针和发射光谱等等离子体诊断方法, 对辅助等离子体源在多晶硅薄膜制备过程中所起到的作用进行了讨论.     

衬底温度对反应磁控溅射W掺杂ZnO薄膜的微观结构及光电性能的影响

采用直流脉冲反应磁控溅射方法生长W掺杂ZnO（WZO）透明导电氧化物薄膜并研究了衬底温度对薄膜微观结构、组分、表面形貌以及光电性能的影响.实验结果表明,WZO薄膜具有良好的（002）晶面择优取向,且适当的衬底温度是制备优质WZO薄膜的关键因素.随着衬底温度升高,薄膜表面粗糙度先增大后减小;衬底温度较高时,薄膜的结构致密,结晶质量好,电子迁移率高.当衬底温度为325℃时,WZO薄膜获得最低电阻率9.25×10^-3Ω·cm,方块电阻为56.24Ω/□,迁移率为11.8 cm² V^-1·s^-1,其在可见光及近红外区域（400—1500 nm）范围的平均透过率达到85.7%.     

直流磁控溅射一步法原位制备MgB2超导薄膜

用MgB2靶,控制直流磁控溅射工作在异常辉光放电或弧光放电状态,在SrTiO3衬底上原位一次性得到了MgB2超导薄膜,其起始转变温度为32K,零电阻温度为15K. 关键词： 高温超导体 超导薄膜 磁控溅射 二硼化镁     

Optical and electrical properties of nanocrystal zinc oxide films prepared by dc magnetron sputtering at different sputtering pressures

The nanocrystal thin films of zinc oxide doped by Al (ZnO:Al) were deposited by dc reactive magnetron sputtering on the glass substrates, in the pressure range of 33-51 Pa. From the X-ray diffraction patterns, the nanocrystalline structure of ZnO:Al films and the grain size were determined. The optical transmission spectra depend from the sputtering pressure, but their average value was 90% in the range from 33 Pa to 47 Pa. Also, the sputtering pressure changes the optical band gap of ZnO:Al films, which is highest for films deposited at 37 Pa, 40 Pa and 47 Pa. The obtained films at room temperature have a sheet resistance of 190 Ω/cm² which increases with time, but the films annealed at temperature of 400 °C have constant resistance. The surface morphology of the films was studied by Scanning electron microscopy. XPS spectra showed that the peak of O1s of the as-deposited films is smaller than the peak of the annealed ZnO:Al films.     

立方氮化硼薄膜的光学带隙

用射频溅射法在p型Si(100)衬底上沉积立方氮化硼(c-BN)薄膜,薄膜的成分由傅里叶变换红外谱标识,用紫外-可见分光光度计测量了c-BN薄膜的反射光谱,利用K-K(Kramers-Kroning)关系从反射谱计算出c-BN薄膜的光吸收系数,进而确定c-BN薄膜的光学带隙.对于立方相含量为55.4%的c-BN薄膜,光学带隙为5.38eV. 关键词： 立方氮化硼薄膜 光学带隙 K-K关系     

Effects of sapphire substrates surface treatment on the ZnO thin films grown by magnetron sputtering

The surface treatment effects of sapphire substrate on the ZnO thin films grown by magnetron sputtering were studied. The sapphire substrates properties have been investigated by means of atomic force microscopy (AFM) and X-ray diffraction rocking curves (XRCs). The results show that sapphire substrate surfaces have the best quality by CMP with subsequent chemical etching. The surface treatment effects of sapphire substrate on the ZnO thin films were examined by X-ray diffraction (XRD) and photoluminescence (PL) measurements. Results show that the intensity of (0 0 2) diffraction peak of ZnO thin films on sapphire substrates treated by CMP with subsequent chemical etching was strongest, FWHM of (0 0 2) diffraction peak is the narrowest and the intensity of UV peak of PL spectrum is strongest, indicating surface treatment on sapphire substrate preparation may improve ZnO thin films crystal quality and photoluminescent property.     

退火处理对磁控溅射制备LaCoO_3薄膜性能的影响

采用磁控溅射法在硅衬底上制备了LaCoO_3(LCO)薄膜,研究了退火温度对LCO薄膜组织结构、表面形貌及热电特性的影响,并利用X射线衍射仪、原子力显微镜(AFM)、激光导热仪等对LCO薄膜的晶体结构、表面形貌、热扩散系数等进行测量与表征.结果表明:退火温度对LCO薄膜的结晶度、晶粒尺寸和薄膜表面形貌都有较大影响;退火前后LCO薄膜的热扩散系数都随温度的升高而减小,且变化速率逐渐减缓; LCO薄膜的热扩散系数随退化温度的升高先增大后减小.LCO薄膜经过700℃退火后得到最佳的综合性能,其薄膜表面致密、平整,结晶质量最好,热扩散系数最小,热电性能最好.     

The structure and photocatalytic activity of TiO2 thin films deposited by dc magnetron sputtering

This paper seeks to determine the optimal settings for the deposition parameters, for TiO₂ thin film, prepared on non-alkali glass substrates, by direct current (dc) sputtering, using a ceramic TiO₂ target in an argon gas environment. An orthogonal array, the signal-to-noise ratio and analysis of variance are used to analyze the effect of the deposition parameters. Using the Taguchi method for design of a robust experiment, the interactions between factors are also investigated. The main deposition parameters, such as dc power (W), sputtering pressure (Pa), substrate temperature (°C) and deposition time (min), were optimized, with reference to the structure and photocatalytic characteristics of TiO₂. The results of this study show that substrate temperature and deposition time have the most significant effect on photocatalytic performance. For the optimal combination of deposition parameters, the (1 1 0) and (2 0 0) peaks of the rutile structure and the (2 0 0) peak of the anatase structure were observed, at 2θ ∼ 27.4°, 39.2° and 48°, respectively. The experimental results illustrate that the Taguchi method allowed a suitable solution to the problem, with the minimum number of trials, compared to a full factorial design. The adhesion of the coatings was also measured and evaluated, via a scratch test. Superior wear behavior was observed, for the TiO₂ film, because of the increased strength of the interface of micro-blasted tools.     

Fabrication and structural characterization of metal films coated on cenosphere particles by magnetron sputtering deposition

Metal films were successfully coated on cenosphere particles using a magnetron sputtering deposition system in which a newly designed sample stage equipped with an ultrasonic vibration generator was used for the tumbling of cenosphere particles. It was found by FE-SEM and AFM results that the films were well compacted and highly uniform in thickness. Due to the difference in sputtering rate, the film thicknesses estimated from FE-SEM characterizations in backscattered mode were <10, 39, 50 and 134 nm for Co, Ni, Cu and Ag films, respectively, under the same sputtering deposition conditions. The RMS values derived from the AFM measurements were 1.94, 4.31, 10.92 and 18.33 nm for Co, Ni, Cu and Ag films, respectively, which can ascribe to the different crystallization behaviors for the four metals. The experiment results indicate that the coating method can be applicable for the fabrication of many other films on cenosphere particles which can be sputter deposited.     

Microstructure, optical and electrical properties of nitrogen doped sp-rich a-C thin films grown by facing-target magnetron sputtering

N atoms were incorporated into sp²-rich a-C networks using DC facing-target reactive sputtering at various N₂ fraction (P_N2) and their structure and opto-electrical properties were investigated systematically. As P_N2 increases, the fraction of CN bonded carbons (or the N content) increases primarily at the expense of the CC bonded carbons and then reaches its saturated value at P_N2 > 40%. The incorporated N preferentially forms different kinds of non-aromatic CN phase, leading to more localization of π electrons and the loss of the connectivity of nanographite fragments in the films, which is different from the case in N-doped sp³-rich a-CN_x films. Hence, with increasing P_N2, the a-C(:N) film converts from a semiconductor with a narrower optical band gap to an insulator-like material with a wider gap. Additionally, the variation of optical constants (n and k) and spin defects are related to the enhancement of the non-aromatic CN phase.     

The electrical, optical properties of AlSb polycrystalline thin films deposited by magnetron co-sputtering without annealing

In order to fabricate AlSb polycrystalline thin films without post annealing, this paper studies a technology of magnetron co-sputtering onto intentionally heated substrate. It compares the structural characteristics and electrical properties of AlSb films which are deposited at different substrate temperatures. It finds that the films prepared at a substrate temperature of 450 oC exhibit an enhanced grain growth with an average grain size of 21 nm and the lattice constant is 0.61562 nm that goes well with unstained lattice constant (0.61355 nm). The ln(σ_dark) ～1/T curves show that the conductivity activation energy is about 0.38 eV when the film is deposited at 450 oC without an annealing. The transmittance and reflectance spectra show that the film deposited at 450 oC has an optical band gap of 1.6 eV. These results indicate that we have prepared AlSb polycrystalline films which do not need a post annealing.     

不同衬底和CdCl2退火对磁控溅射CdS薄膜性能的影响

在科宁7059玻璃, FTO, ITO, AZO四种衬底上磁控溅射CdS薄膜, 并在CdCl₂+干燥空气380 ℃退火, 分别研究了不同衬底和退火工艺对CdS薄膜形貌、结构和光学性能的影响. 扫描电子显微镜形貌表明: 不同衬底原位溅射CdS薄膜的形貌不同, 退火后相应CdS薄膜的晶粒度和表面粗糙度明显增大. XRD衍射图谱表明: 不同衬底原位溅射和退火CdS薄膜均为六角相和立方相的混相结构, 退火前后科宁7059玻璃, FTO, AZO衬底上CdS薄膜有 H(002)/C(111) 最强衍射峰, ITO衬底原位溅射CdS薄膜没有明显的最强衍射峰, 退火后出现 H(002)/(111) 最强衍射峰. 紫外-可见分光光度计分析表明: AZO, FTO, ITO, 科宁7059玻璃衬底CdS薄膜的可见光平均透过率依次减小, 退火后相应衬底CdS薄膜的可见光平均透过率增大, 光学吸收系数降低; 退火显著增大了不同衬底CdS薄膜的光学带隙. 分析得出: 上述结果是由于不同衬底类型和退火工艺对CdS多晶薄膜的形貌、结构和带尾态掺杂浓度改变的结果. 关键词： CdS薄膜 磁控溅射 退火再结晶 带尾态     

Structure, electrical and chemical properties of zirconium nitride films deposited by dc reactive magnetron sputtering

2 and Ar ambient. X-ray diffraction indicated that growth of ZrN with a preferred (111) orientation over Si(100) was achieved. The resistivity of the films varies from 200 μΩcm to 15 μΩcm depending on the N₂ content in the working gas. The square resistance of the films deposited on 96% Al₂O₃ ceramic wafers is stable below 300 °C. Received: 17 June 1996/Accepted: 9 December 1996     

Properties of dc magnetron sputtered Cu2O films prepared at different sputtering pressures

The sputtering pressures maintained during the deposition of Cu₂O films, by dc reactive magnetron sputtering, influence the structural, electrical and optical properties. The crystalline orientation mainly depends on the sputtering pressure. The films deposited at a sputtering pressure of 4 Pa showed single-phase Cu₂O films along (1 1 1) direction. The electrical resistivity of the films increased from 1.1 × 10¹ Ω cm to 3.2 × 10³ Ω cm. The transmittance of the films increased from 69% to 88% with the increase of sputtering pressure from 2.5 Pa to 8 Pa.