Preparation of novel porous carbon spheres from corn starch

Irregular porous carbon spheres were successfully prepared from Na₂SnO₃ coated corn porous starch by carbonization. The product was characterized with X-ray diffraction and scanning electron microscope (SEM). It is verified that the irregular porous carbon spheres are composed of disordered carbon, and the skeleton and pores of the corn porous starch was well preserved after carbonization. The pore size of the irregular porous carbon spheres is almost the same, which is similar to that of the porous starch. And the pore size decreases from about 0.91 μm to 0.53 μm measured from the SEM pictures. The texture of the irregular porous carbon spheres is mainly determined by that of porous starch.     

Voltammetric determination of hypoxanthine based on the enhancement effect of mesoporous TiO2-modified electrode

A mesoporous TiO₂ was synthesized according to the reported method, and then used to modify the carbon paste electrode (CPE). The electrochemical behavior of hypoxanthine was investigated with great detail. Compared with the unmodified CPE, the mesoporous TiO₂-modified CPE greatly enhances the oxidation signal of hypoxanthine. Due to huge surface area, well-defined and special mesopores, the mesoporous TiO₂-modified CPE shows considerable enhancement effect toward hypoxanthine. Based on this, a sensitive, rapid and convenient electrochemical method was developed for the determination of hypoxanthine. The linear range is over the range from 2.0 × 10⁻⁷ to 5.0 × 10⁻⁵ mol L⁻¹, and the limit of detection is estimated to be 5.0 × 10⁻⁸ mol L⁻¹. The relative standard deviation (RSD) for 10 mesoporous TiO₂-modified CPEs is 5.7%. Finally, this sensing method was successfully used to determine hypoxanthine in human blood serum samples.     

Features of sulfur hexafluoride adsorption on carbon adsorbents

The isotherms describing excess adsorption of SF₆ and N₆I₆ on carbon adsorbents with different pore structures were measured at pressures of 0.001—2.4 and 0.0001—0.1 MPa, respectively, and temperatures of 298—408 E. A linear dependence of Henry"s constant on temperature in the lnK—10³/O coordinates was found for all the samples. The specific surface areas of the samples determined by the BET method from the SF₆ adsorption are lower than those derived from benzene adsorption. The most pronounced difference was found for the grafitized carbon black. When SF₆ was adsorbed on supermicroporous carbon AC-71 and on microporous carbons PAC and CMS, a hysteresis was found, which, unlike that on mesoporous carbon adsorbents, is observed in the initial region of the equilibrium pressures.     

Dual template method to prepare hierarchical porous carbon nanofibers for high-power supercapacitors

Hierarchical porous carbon nanofibers serving as electrode materials are prepared through carbonization and hydrofluoric acid treatment of polyacrylonitrile-based electrospinning involving dual templates. The hierarchical porous structures are synergistically tailored by varying template contents in the spinning solution. The carbon nanofibers prepared from the electrospinning of polyacrylonitrile containing 15/15 wt.% polymethylmethacrylate/tetraethyl orthosilicate exhibit the largest specific surface area (699 m² g^?1) and microporous volume (0.196 cm³ g^?1). In 6 M KOH electrolyte, a symmetrical supercapacitor equipped with the hierarchical porous carbon nanofibers demonstrates its high-end specific capacitance of 170 F g^?1, superior rate capability, and high-power density output up to 14.7 kW kg^?1. Cycling evolution indicates capacitance fading is only 5.8 % of initial capacitance at a current density of 1 A g^?1 even after 8,000 cycles. The excellent electrochemical performances of the carbon nanofiber are mainly ascribed to the optimized pore size distributions of both micropores and mesopores and the unique hierarchical pore structures possessed by abundant micropores.     

One-step synthesis of biomass derived O,N-codoped hierarchical porous carbon with high surface area for supercapacitors

We report a convenient method to synthesize O, N-codoped hierarchical porous carbon by one-step carbonization of the mixture of KHCO₃, urea and alginic acid. Benefiting from KHCO₃ and urea synergistic effect, the obtained O, N-codoped hierarchical porous carbon (NPC-700) material has a well-developed interconnected porous framework with ultrahigh specific surface area (2846 m²/g) and massive heteroatoms functional groups. Consequence, such porous carbon displays high specific capacitance (324 F/g at 1 A/g), excellent rate performance (212 F/g at 30 A/g) and good electrochemical stabilization in 6 mol/L KOH solution. More importantly, the assembled NPC-700//NPC-700 symmetrical supercapacitor can achieve a high energy density of 18.8 Wh/kg and good electrochemical stabilization in 1 mol/L Na₂SO₄ solution. This process opens up a new way to design heteroatoms-doped hierarchical porous carbon derived from biomass materials for supercapacitors.     

Synthesis of Hierarchical Macro‐/Mesoporous Solid‐Solution Photocatalysts by a Polymerization–Carbonization–Oxidation Route: The Case of Ce0.49Zr0.37Bi0.14O1.93

A hierarchical macro‐/mesoporous Ce_0.49Zr_0.37Bi_0.14O_1.93 solid‐solution network has been synthesized on a large scale by means of a simple and general polymerization–carbonization–oxidation synthetic route. The as‐prepared product has been characterized by SEM, XRD, TEM, BET surface area measurement, UV/Vis diffuse‐reflectance spectroscopy, energy‐dispersive X‐ray spectroscopy (EDS), and photoelectrochemistry measurements. The photocatalytic activity of the product has been demonstrated through the photocatalytic degradation of methyl orange. Structural characterization has indicated that the hierarchical macro‐/mesoporous solid‐solution network not only contains numerous macropores, but also possesses an interior mesoporous structure. The mesopore size and BET surface area of the network have been measured as 2–25 nm and 140.5 m² g^?1, respectively. The hierarchical macro‐/mesoporous solid‐solution network with open and accessible pores was found to be well‐preserved after calcination at 800 °C, indicating especially high thermal stability. Due to its high specific surface area, the synergistic effect of the coupling of macropores and mesopores, and its high crystallinity, the Ce_0.49Zr_0.37Bi_0.14O_1.93 solid‐solution material shows a strong structure‐induced enhancement of visible‐light harvest and exhibits significantly improved visible‐light photocatalytic activity in the photodegradation of methyl orange compared with those of its other forms, such as mesoporous hollow spheres and bulk particles.     

由含铝金属有机骨架材料制备的多孔碳在锂硫电池中的应用

采用水热法制备了一种含铝金属有机骨架材料, 其在高温下发生炭化得到多孔碳, 最后与硫复合制得锂硫电池正极材料. XRD图谱显示在高温炭化时多孔碳样品出现了部分石墨化. N₂等温吸附-脱附测试分析显示合成的多孔碳材料含有微孔和介孔结构. 对不同载硫量的锂硫电池进行了充放电性能测试, 结果显示S质量分数为46.3%的样品在0.01 C倍率下首次放电容量达到1272 mA·h/g; 在0.1 C倍率下首次放电容量为934 mA·h/g, 循环性能良好.     

Electrochemical performance of sulfur composite cathode materials for rechargeable lithium batteries

The structure and characteristic of carbon materials have a direct influence on the electrochemical performance of sulfur-carbon composite electrode materials for lithium-sulfur battery.In this paper,sulfur composite has been synthesized by heating a mixture of elemental sulfur and activated carbon,which is characterized as high specific surface area and microporous structure.The composite,contained 70%sulfur,as cathode in a lithium cell based on organic liquid electrolyte was tested at room temperature....     

Preparation of Bamboo-Based Hierarchical Porous Carbon Modulated by FeCl3 towards Efficient Copper Adsorption

Using bamboo powder biochar as raw material, high-quality meso/microporous controlled hierarchical porous carbon was prepared—through the catalysis of Fe³⁺ ions loading, in addition to a chemical activation method—and then used to adsorb copper ions in an aqueous solution. The preparation process mainly included two steps: load-alkali leaching and chemical activation. The porosity characteristics (specific surface area and mesopore ratio) were controlled by changing the K₂CO₃ impregnation ratio, activation temperature, and Fe³⁺ ions loading during the activation process. Additionally, three FBPC samples with different pore structures and characteristics were studied for copper adsorption. The results indicate that the adsorption performance of the bamboo powder biochar FBPC material was greatly affected by the meso/micropore ratio. FBPC _2.5-900-2%, impregnated at a K₂CO₃: biochar ratio of 2.5 and a Fe³⁺: biochar mass ratio of 2%, and activated at 900 °C for 2 h in N₂ atmosphere, has a very high specific surface area of 1996 m² g⁻¹ with a 58.1% mesoporous ratio. Moreover, it exhibits an excellent adsorption capacity of 256 mg g⁻¹ and rapid adsorption kinetics for copper ions. The experimental results show that it is feasible to control the hierarchical pore structure of bamboo biochar-derived carbons as a high-performance adsorbent to remove copper ions from water.     

Physico-chemical and electrical properties of activated carbon cloths: Effect of inherent nature of the fabric precursor

Five different cellulose-based fabrics were used to prepare activated carbon cloths (ACCs) by phosphoric acid activation at pre-established experimental conditions, in an attempt to explore the effect of the precursor's nature on properties of the resulting ACCs. Characterization by elemental analysis, nitrogen (77 K) adsorption, and scanning electron microscopy was carried out. Electrical properties of the developed ACCs were investigated to examine the possibility of regenerating the ACCs by direct electrical heating. Thermal behavior of the raw precursor and of one of the acid-treated fabrics was also studied by thermogravimetric analysis and noticeable differences due to the precursors’ characteristics and acid impregnation were detected, respectively. The ACCs derived from a denim precursor showed BET surface area (784 m² g⁻¹) and total pore volume (0.40 cm³ g⁻¹) lower than those obtained from the four other precursors (1058–1183 m² g⁻¹, 0.55–0.67 cm³ g⁻¹), whereas carbon content and yield for the former were higher. Morphology and physical appearance of the ACCs were dependent on the raw fabric employed, with most of the samples presenting well-preserved fibres integrity. Besides, the denim-derived ACCs also showed the lowest electrical resistivity (8.10⁻³ Ωm). It was properly correlated with the elemental carbon content and total pore volume of the developed ACCs.     

Adsorption and DSC study of mineral–carbon sorbents obtained from coal tar pitch–polymer compositions

The purpose of this study was to determine the possibility of producing hydrophobic mesoporous mineral–carbon sorbents from aluminum hydroxide and compositions of coal tar pitch–polymers on carbonization at 600 °C in a nitrogen atmosphere. Blends of the products of co-precipitation of aluminum hydroxide in the carbonaceous substances medium were subjected to carbonization process. The extent of porous structure development was evaluated using low temperature nitrogen adsorption, adsorption of benzene vapors, and adsorption of iodine from aqueous solution. The highest value of BET surface area of about 370 m²/g was achieved for the carbonization product obtained from co-precipitated raw components with 10 wt% compositions coal tar pitch–polymer. These materials demonstrated high capacity to reduce organic pollutions from sewage. Pitch–polymer composition containing poly(ethylene terephthalate) or phenol–formaldehyde resin was studied by the means of DSC method in order to determine the high-temperature transformations taking place under the conditions of carbonization. DSC method enables to determine i.a. the decomposition temperatures of carbonizates produced from pitch–polymer compositions and the evaluation of their sorption abilities. The additive of poly(ethylene terephthalate) and phenol–formaldehyde resin caused the increase of thermal resistance of the pitch expressed by higher decomposition temperatures.     

Enhanced electrochemical capacitance of nitrogen-doped carbon gels synthesized by microwave-assisted polymerization of resorcinol and formaldehyde

Nitrogen-doped carbon gels were synthesized by ammonia-assisted carbonization of resorcinol–formaldehyde (RF) polymers obtained under microwave irradiation without any basic catalyst. Compared with the RF polymer synthesized by the conventional hydrothermal method, microwave polymerization produced spherical beads with a higher surface area (1710 m²/g vs. 1080 m²/g), and smaller (∼700 nm vs. ∼5 μm) but more uniform bead sizes. The majority of their pores were micropores. As a result, the electrochemical capacitance of microwave-assisted nitrogen-doped carbons was significantly higher than that of materials prepared by the conventional hydrothermal method. Thus microwave-assisted polymerization followed by ammonia-assisted carbonization is a useful method to synthesize nitrogen-doped carbon gels for electrochemical double layer capacitors.     

Preparation and characterization of SiO2/TiO2 composite microspheres with microporous SiO2 core/mesoporous TiO2 shell

SiO₂/TiO₂ composite microspheres with microporous SiO₂ core/mesoporous TiO₂ shell structures were prepared by hydrolysis of titanium tetrabutylorthotitanate (TTBT) in the presence of microporous silica microspheres using hydroxypropyl cellulose (HPC) as a surface esterification agent and porous template, and then dried and calcined at different temperatures. The as-prepared products were characterized with differential thermal analysis and thermogravimetric (DTA/TG), scanning electron microscopy (SEM), X-ray diffraction (XRD), nitrogen adsorption. The results showed that composite particles were about 1.8 μm in diameter, and had a spherical morphology and a narrow size distribution. Uniform mesoporous titania coatings on the surfaces of microporous silica microspheres could be obtained by adjusting the HPC concentration to an optimal concentration of about 3.2 mmol L⁻¹. The anatase and rutile phase in the SiO₂/TiO₂ composite microspheres began to form at 700 and 900 °C, respectively. At 700 °C, the specific surface area and pore volume of the SiO₂/TiO₂ composite microspheres were 552 and 0.652 mL g⁻¹, respectively. However, at 900 °C, the specific surface area and pore volume significantly decreased due to the phase transformation from anatase to rutile.     

Mesoporous silica functionalized with diethylenetriamine moieties for metal removal and thermodynamics of cation–basic center interactions

The inorganic–organic hybrid material was synthesized by co-condensation of tetraethylorthosilicate and the organosilane N-[3-(trimethoxysilyl)propyl]diethylenetriamine. Spectroscopic analysis of the hybrid material by FTIR showed bands at 2937 and 2839 cm⁻¹ related to ν(CH); ²⁹Si NMR spectrum gave signals at −108, −99, −68 and −59 ppm, Q⁴, Q³, T⁴ and T² species related to the silica backbone structure. The well-defined peaks obtained in the ¹³C NMR spectrum in the 10–58 ppm region confirmed the attachment of organic functional groups as pendant chains bonded into the porous silica. Particle morphology evaluated by a scanning electron microscopic (SEM) study showed the formation of spherical particles in the nanometer range. The X-ray diffraction pattern showed a peak at a 2θ of 2.3°, demonstrating the mesoporous characteristic of the synthesized material. Adsorption evaluated by batch equilibrium processes gave the maximum adsorption of 2.2 and 2.8 mmol g⁻¹ for copper and nickel, respectively. From these values a stoichiometry of 2:1 for cation/ligand was established, considering the amount of 1.2 mmol of pendant groups per gram of the hybrid material. Thermodynamic parameters related to the adsorption of metal ions, evaluated using the calorimetric titration technique presented a negative Gibbs free energy value, in agreement with the spontaneity of cation removal on the basic center in the mesoporous silica at the solid/liquid interface.     

Flexible carbon membrane supercapacitor based on γ-cyclodextrin-MOF

Supercapacitors (SCs) with high energy density and power density are a research hotspot. Herein, we report a flexible porous carbon membrane supercapacitor prepared by electrospinning polyacrylonitrile (PAN) with γ-cyclodextrin-MOF (γ-CD-MOF) and then carbonizing at 900 °C. BET results showed that the supercapacitor retained the skeleton of γ-CD, γ-CD-MOF and the pores formed by the spun-fibers, which were 0.73, 1.09 and 23–186 nm, respectively, showing a high specific surface area of 134.7 m²/g. The hierarchically porous structures ensure rapid charge transfer and ion diffusion, resulting in the PAN/γ-CD-MOF carbon electrode with a high capacity of 283.3 F/g. Moreover, the supercapacitor had a high energy density up to 17.5 Wh/kg and power density up to 6 kW/kg. Significantly, it showed excellent cycle stability with a capacitance retention of 97.5% after 6000 cycles. This work provides a supramolecular strategy to construct a flexible porous carbon membrane, which has potential for supercapacitor applications.     

Microbubble formation using asymmetric Shirasu porous glass (SPG) membranes and porous ceramic membranes—A comparative study

We have recently proposed a new method for generating uniformly sized microbubbles from Shirasu porous glass (SPG) membranes with a narrow pore size distribution. In this study, to obtain a high gas permeation rate through SPG membranes in microbubble formation process, asymmetric SPG membranes were used. At the transmembrane/bubble point pressure ratio of less than 1.50, uniformly sized microbubbles with a bubble/pore diameter ratio of approximately 9 were generated from an asymmetric SPG membrane with a mean pore diameter of 1.58 μm and a skin-layer thickness of 12 ± 2 μm at a gaseous-phase flux of 2.1–24.6 m³ m⁻² h⁻¹, which was much higher than that through a symmetric SPG membrane with the same pore diameter. This is mainly due to the much smaller membrane resistance of the asymmetric SPG membrane. Only 0.27–0.43% of the pores of the asymmetric SPG membrane was active under the same conditions. The proportion of active pores increased with a decrease in the thickness of skin layer. In contrast to the microbubble formation from asymmetric SPG membranes, polydispersed larger bubbles were generated from asymmetric porous ceramic membranes used in this study, due to the surface defects on the skin layer. The surface defects were observed by the scanning electron microscopy and detected by the bubble point method.     

Effect of preparation pH on pore structure of silica gels

Surface characterization of silica gels prepared at different gelation pH from water glass and sulphuric acid were made by argon adsorption at 77 K using continuous volumetric method. While microporous silica gels prepared in the pH range of 1–3 had BET surface areas of 504–571 m² g^–1, total pore volumes of 0.26–0.31 cm³ g^–1 and micropore volumes of 0.16–0.23 cm³ g^–1, mesoporous silica gels prepared in the pH range of 3.36–0.65 had BET surface areas of 374–530 m² g^–1 and pore volumes of 0.61–0.79 cm³ g^–1.     

A tunable hierarchical porous carbon from starch pretreated by calcium acetate for high performance supercapacitors

Hierarchical porous carbons (HPCs) with abundant mesopores have been prepared by a facile route from the starch that was pretreated by calcium acetate. The scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and N₂ adsorption–desorption tests show that hierarchical porous carbons with bimodal mesopores have been obtained. Moreover, the pore sizes are tunable by simply adjusting the reactants ratio and carbonization temperature. The as-synthesized hierarchical porous carbon materials (HPCs-2-800) possesses the highest Brunauer-Emmett-Teller (BET)-specific surface area of 464 m² g^?1 and mesoporous volume of 0.663 cm³ g^?1 at the carbonization temperature of 800 °C and starch to calcium acetate mass ratio of 2. Electrochemical measurements also display that the HPCs-2-800 electrodes have a high reversible capacity of 244 F g^?1 at the current density of 0.1 A g^?1 and 182 F g^?1 at the current density of 10 A g^?1. When the current density is elevated from 0.1 to 10 A g^?1, the high capacitance retention of 74.6 % reveals a good rate performance. Long charge–discharge cycling measurements disclose good stabilities over 25,000 cycles at different current densities of 1–10 A g^?1 (5000 cycles at each current density) for HPCs-2-800 electrode. The cycling results indicate a high capacitance retention of 99.6 % over 5000 charge–discharge cycles even at the current density of 10 A g^?1. The excellent supercapacitive performances imply that HPCs-2-800 is a promising candidate for supercapacitors.     

High performance anode-supported intermediate temperature solid oxide fuel cells (IT-SOFCs) with La0.8Sr0.2Ga0.8Mg0.2O3−δ electrolyte films prepared by electrophoretic deposition

Remarkable power density was obtained for anode-supported solid oxide fuel cells (SOFCs) based on La_0.8Sr_0.2Ga_0.8Mg_0.2O_3−δ (LSGM) electrolyte films, fabricated following an original procedure that allowed avoiding undesired reactions between LSGM and electrode materials, especially Ni. Electrophoretic deposition (EPD) was used for the fabrication of 30 μm-thick electrolyte films. Anode supports were made of La_0.4Ce_0.6O_2−x (LDC). The LSGM powder was deposited by EPD on an LDC green tape-cast membrane added with carbon powder, both as pore former and substrate conductivity booster. A subsequent co-firing step at 1490 °C produced dense electrolyte films on porous LDC skeletons. Then, a La_0.8Sr_0.2Fe_0.8Co_0.2O_3−δ (LSFC) cathode was applied by slurry-coating and calcined at 1100 °C. Finally, the porous LDC layer was impregnated with molten Ni nitrate to obtain, after calcination at 900 °C, a composite NiO–LDC anode. Maximum power densities of 780, 450, 275, 175, and 100 mW/cm² at 700, 650, 600, 550, and 500 °C, respectively, were obtained using H₂ as fuel and air as oxidant, demonstrating the success of the processing strategy. As a comparison, electrolyte-supported SOFCs made of the same materials were tested, showing a maximum power density of 150 mW/cm² at 700 °C, more than 5 times smaller than the anode-supported counterpart.     

Hierarchical control of porous silica by pH adjustment: Alkyl polyamines as surfactants for bimodal silica synthesis and its carbon replica

Bimodal macro-mesoporous silica networks have been prepared in a simple one-pot synthesis using an inexpensive tetramine surfactant and tetraethoxysilane as a silica precursor. These novel materials show high pore volumes and templated mesopores (average pore size 3.0 nm) embedded in 20 nm thick walls forming interparticle large meso/macropores. The judicious control of the pH during the silica formation allows for the precise control of the interparticle condensation, likely due to the change in the interaction between the tetramine surfactant and the silica precursors. Finally, a highly porous carbon replica with bimodal porosity was prepared by using the bimodal silica as a hard sacrificial template. The microstructure of the silica template was accurately transferred to the carbon material obtaining high surface areas (up to 1300 m² g⁻¹) and total pore volumes ≥2 cm³ g⁻¹.