利用自相关方法实现光脉冲时间延迟精确测量

为了满足在高精度波分复用/时分复用光采样系统中,采样光脉冲时间抖动低于100 fs的要求,开发了一套基于自相关法测量时间延迟的系统。通过光纤耦合器连接一路参考光路将光脉冲在时域上进行"复制",并使初始光脉冲和"复制"光脉冲相关,得到参考光路和被测光路的精确光程差,进而固定参考光路并接入不同被测光路从而得到多路被测光路之间相对延时。实验结果表明,利用自相关法测量脉冲时间间隔精度优于50 fs,满足波分复用/时分复用光采样系统研究需要。     

红外耦合光学系统设计

红外目标模拟器由红外目标图像发生器和投影光学系统组成。该红外光学系统是一个要求与2个导引光学系统的光学技术参数相匹配的长焦距、大视场和具有像方远心光路的中红外光学系统。叙述用于红外目标模拟器的红外耦合光学系统的设计原理，提出它与导引光学系统一起可组成放大倍率M=4.5×的红外投影光学系统，并指出IR CRT产生的图像通过红外投影光学系统可成像在导引接收器上。针对给出的红外耦合光学系统的设计特点和技术要求，光学材料选取硅（Si） 锗（Ge） 硅（Si），采用简单的柯克三片式结构完成光学系统设计。设计评价结果表明，该系统的光学性能和成像质量均满足设计指标要求。     

混沌光通信与OC-48光纤通信的波分复用

数值证实并分析了混沌激光通信与现行光通信的波分复用传输,对于100 GHz的信道间隔,混沌激光通信系统实现了传输速率为1 Gbit/s数字信号的保密传输,现行光通信系统实现了传输速率为2.5 Gbit/s数字信号的传输.研究表明,当现行光通信中脉冲光信号的峰值功率不超过17 dBm时,混沌激光通信可在传输距离80 km内实现并行传输.此外,当现行光通信中脉冲光信号的峰值功率为7 dBm时,系统接收到的信号质量受混沌激光通信的干扰很小,当光纤传输距离从80 km增加到160 km时,对应的眼图开启度从82% 关键词： 混沌光通信 混沌同步 波分复用 信道串扰     

基于光码分多址技术的塑料光纤接入网探讨

本文通过对多信道光接入网复用和多址接入方式的分析,提出一种基于光码分多址(OCDMA)技术的塑料光纤接入网结构,同时给出了适合于多媒体信息业务传输的控制协议以及低成本的硬件实现方案,为实现光接入网的最终目标即光纤到办公室(FTTO)或光纤到家庭(FTTH)提供了一条有效的途径.     

基于热膨胀效应的可调光功率分束器设计

可调光功率分束器是集成光子系统中的重要功能器件,其光功率输出具有动态可调控特性,诸多光子系统对其有着广泛需求.本文基于空隙槽型Y分支波导结构,利用热膨胀效应,提出了一种新型可调光功率分束器实现方法,通过调控温度来改变分支处空隙槽的宽度,以实现其分支波导的光功率输出的动态变化.采用有限元方法,对其热膨胀形变和光学性能进行了模拟分析.其模拟结果表明,该器件能实现大范围光分束调控,且对波长和偏振态依赖性低;同时,该器件具有结构简单、易于设计和制作、易于调控等优点,这种新型器件在各种光子系统中具有重要应用前景.     

Optical Multistability and Wavelength Switching of a Fabry-Perot Semiconductor Laser with Multi-Detuned Light Injections

Optical multistability of a Fabry-Perot semiconductor laser is analyzed when multi-optical inputs detuned from the cavity-resonant wavelength of a semiconductor laser are injected. Many split branches are shown to be produced in the optical output versus optical input characteristics for different detuned optical inputs. It is also shown that optical outputs can be switched in any one of the optical input wavelengths by optical input pulses, based on the optical output versus input characteristics with multi-split branches.     

Dynamically controlled optical nonreciprocity of a double-ladder system with spontaneously generated coherence in moving atomic optical lattice

A four-level double-ladder cold atoms system with spontaneously generated coherence trapped in a moving optical lattice is explored to achieve optical nonreciprocity. When spontaneously generated coherence(SGC) is present, the remarkable contrast optical nonreciprocity of light transmission and reflection can be generated at each induced photonic bandgap in the optical lattice with a velocity of a few m/s. However, when the SGC effect is absent, the optical nonreciprocity becomes weak or even vanishing due to the strong absorption. It is found that the optical nonreciprocity is related to the asymmetric Doppler effect in transmission and reflection, meanwhile the degree and position of optical nonreciprocity can be tuned by the SGC effect and the Rabi frequency of the trigger field.     

4×4自由空间光开关结构及其矩阵分析

光开关是全光通信网络中的一种重要的光无源器件。提出了一种4×4自由空间光开关的结构设计方法,并进行了矩阵理论分析。该4×4光开关具有新颖的光模块化结构,该光开关结构仅由偏振分束组合棱镜,λ／4波片,λ／2波片,直角棱镜,全反镜和偏振光调制器组成,对光开关的控制与输入光束的偏振态无关。所有的输出端口可以和输入端口无阻塞地互连交换。这种新型的光开关结构具有光学元件少,结构紧凑,模块化,与偏振无关的特点。基于4×4光开关的矩阵分析得到了路由控制表,为4×4光开关从任意输人端口到任意输出端口的路由控制状态提供了理论分析手段,从而可以方便地实现无阻塞地光交换开关矩阵的路由控制功能。     

Optical bistability using quantum coherence in a microwave-driven four-level atomic system

The behavior of the optical bistability (OB) is investigated in an optical system which consists of a four-level atomic system with a microwave drive field and an optical cavity. It is found that the optical bistability can be accomplished by adjusting different physical parameters in both steady and transient process. Due to the existence of the microwave drive field, the optical bistability can be also obtained even under weak coherent coupling field condition. Since the intensity and phase of microwave drive field can be conveniently modulated, this optical system provides a new experimental method to test the optical bistability theory.     

Polarization-independent bidirectional 4×4 optical switch in free space

Optical switches play an important role in all optical communication networks and multiprocessor computer systems. The 2×2 and 4×4 optical switches are the basic units of large-scale switch matrices. Using a conventional polarization control method, the optical switch system and structure is optimized, and a novel optical switch is proposed, which has the advantages of relatively low crosstalk and insertion loss, compact and simple construction, higher performance and cost effectiveness. First, a novel 2×2 optical switch is proposed using phase spatial light modulator (PSLM), polarizing beam splitter (PBS) and mirror. This configuration uses fewer optical components, is compact in structure, efficient in performance, and insensitive to polarization of the signal beam. Second, a new optical experimental module of 4×4 optical switch is presented by cascading a 2×2 optical switch. The routing method of polarization-independent bidirectional 4×4 optical switch is investigated. Finally, the operational characteristics of the polarization-independent bidirectional 2×2 and 4×2 optical switches are discussed in detail.     

算符光学中的表象变换及关联方程的普适解法

本文由光学变量算符的线性变换将文献[3]建立的光学矩阵与光学算符的关联方程加以推广,得到光学广义关联方程;又引入本征光学变量算符使其简化成约化光学广义关联方程;从而获得由关联方程求光学点扩散算符的“模拟单透镜成象光路”的普适解法。 关键词：     

The preparation of optical fibre nanoprobe and its application in spectral detection

As an important component of scanning near-field optical microscope (SNOM), optical fibre nanoprobe has been applied to many fields extensively. A melt-stretched etching method is proposed to produce optical fibre nanoprobe with low cost. Firstly, optical fibre tip with micrometer-sized diameter is created by the melt-stretched measure. Next, it is dipped into hydrofluoric acid (HF), and a fine optical fibre nanoprobe will be made after a short-time etching. Owing to the taper structure of tip, it can be etched again in acid if a nanoprobe is not constructed when the first etching is completed. In addition, optical fibre nanoprobe is applied to spectral investigation, and the fluorescence spectroscopy of rhodamine B (Rh B) solution is collected by an optical investigation system with a bifurcated fibre.     

A method of developing frequency encoded multi-bit optical data comparator using semiconductor optical amplifier

Optical data comparator is the part and parcel of arithmetic and logical unit of any optical data processor and it is working as a building block in a larger optical circuit, as an optical switch in all optical header processing and optical packet switching based all optical telecommunications system. In this article the author proposes a method of developing an all optical single bit comparator unit and subsequently extending the proposal to develop a n-bit comparator exploiting the nonlinear rotation of the state of polarization of the probe beam in semiconductor optical amplifier (SOA). Here the dataset to be compared are taken in frequency encoded/decoded form throughout the communication. The major advantages of frequency encoding over all other conventional techniques are that as the frequency of any signal is fundamental one so it can preserve its identity throughout the communication of optical signal and minimizes the probability of bit error problem. For frequency routing purpose optical add/drop multiplexer (ADM) is used which not only route the pump beams properly but also to amplify the pump beams efficiently. Switching speed of ‘MZI-SOA switch’ as well as SOA based switches are very fast with good on–off contrast ratio and as a result it is possible to obtain very fast action of optical data comparator.     

Using diffractograms to evaluate optical systems with coherent illumination

A new approach to measuring aberrations of an optical system with coherent illumination is introduced. The optical system is evaluated by use of a so-called weak phase object and by digital image recording and processing. Based on the contrast transfer function theory for coherent systems, the main aberrations of the optical system can be determined. This is a convenient approach to evaluating and measuring complex optical systems with numerous optical elements after assembly and can serve as a simple performance test of an optical instrument in the field.     

两腔级联纠缠增强的理论分析

高纠缠度的纠缠源是实现高保真度量子信息传输与处理的保障,因为受到光学元器件自身性能不完美的限制,通过有效的操控手段来提高光场的纠缠度是十分必要的.连续变量Einstein-Podolsky-Rosen纠缠态光场可以利用工作在阈值以下的非简并光学参量放大器来获得.将两个非简并光学参量放大器级联,可以利用第二个光学腔来操控第一个光学腔输出的纠缠态光场,在一定条件下实现光场的纠缠增强.本文通过理论分析设计出两种光学腔级联的实验系统,其中,纠缠产生装置采用具有三共振结构的半整块驻波腔,输出到目前为止世界上单腔获得两组份纠缠态光场纠缠度的最高值,操控光学腔采用驻波腔或四镜环形腔的结构.详细对比分析了不同结构的操控腔对纠缠增强效果的影响,得出利用不同腔形作为操控腔的最佳实验方案.同时分析了级联腔输出光场的纠缠度随不同物理参量的变化关系,得出进一步优化的最佳实验系统参量,为实验获得更高纠缠度的纠缠态光场提供了依据.     

Bistable switching using an optical Tamm cavity with a Kerr medium

All-optical bistable switching is proposed to realize by using an optical Tamm cavity in which a Kerr medium is sandwiched between a metal layer and a Bragg mirror. Results show that the excitation of clockwise and counterclockwise bistable switching under the control of external optical injection is due to the presence of optical Tamm states. In addition, the bistable characteristics of optical Tamm cavities are found to be sensitive to the polarization of external optical injection.     

基于稳像理论的空间光学遥感像移补偿的分析与计算

动态光学是研究光学系统及元件动态成像特性的一门学科。稳像系统是动态光学系统的重要组成部分。稳像系统是为了维持图像的稳定、清晰,要求光学组元件按规定的要求做相对运动,从而实现图像的最终稳定、清晰。空间遥感成像的分析对于遥感器的运用至关重要。基于稳像理论——动态光学理论,进行了空间遥感器的成像面像移分析,分析结果与采用齐次坐标变换方法所得结论一致,不但证明通过齐次坐标变换方法得出的结果是正确的,而且说明采用动态光学的稳像理论解决以上问题物理概念更清楚,计算简便。同时对于类似的运动光学系统,稳像理论也具有很好的适用性。     

一种测量GaAs-GaAlAs行波激光放大器增益特性的实验方法

本文报导了一种测量光耦合效率η的新实验方法。这个方法是建立于p-n结短路光电流原理上的。本文推导出适合于行波激光放大器的光耦合效率的公式。短路光电流用一检流计测量,利用公式获得光耦合效率的实验值。利用实验所测光耦合效率,测量了行波激光放大器的增益随注入电流变化的规律,其结果和实验符合。另外本文还介绍了在脉冲注入电流条件下测行波半导体激光放大器增益的实验方法。     

光学超振荡与超振荡光学器件

传统光学器件的衍射极限极大地制约了远场超分辨光学系统的进一步发展.如何从光学器件层面突破光学衍射极限瓶颈,实现非标记远场超分辨光学成像,是光学领域面临的巨大挑战.光学超振荡在不依靠倏逝波的条件下,可以在远场实现任意小的亚波长光场结构,这为突破光学衍射极限提供了一条崭新的途径.近年来,光学超振荡现象和超振荡光学器件的相关研究得到了快速发展,在理论和实验上成功地演示了超振荡光场的产生和多种超振荡光学器件,并在实验上展示了超振荡光学器件在非标记远场超分辨光学显微、成像以及超高密度数据存储等应用领域的巨大优势和应用潜力.本文对光学超振荡相关理论、超振荡光学器件设计理论和方法、超振荡光学器件发展现状、超振荡光场测试方法以及超振荡光学器件的应用等方面进行详细介绍和分析.     

面向21世纪的新型陀螺仪─—光纤陀螺

回顾光纤陀螺发展历史，论述光纤陀螺技术发展的趋势。分析并展望光纤陀螺市场前景，指出当前光纤陀螺是处于大力发展的一种新型陀螺仪，它将成为21世纪陀螺仪市场的主导产品。