Synthesis and characterization of a novel nonlinear optical hyperbranched polymer containing a highly performing chromophore

We report herein the peripheral functionalization of a high glass transition temperature hyperbranched polyimide with a new and highly performing electro‐optic chromophore for the elaboration of a second‐order nonlinear optical material. In this study, the CPO1 chromophore was selected for its very high quadratic hyperpolarizability coefficient (μβ = 31,000 ? 10^?48 esu at 1990 nm) and its ease of synthesis in multigram scale. As a result, the new electro‐optic polymer was characterized by an r₃₃ coefficient around 40 pm/V at 1.5 µm, although the poling conditions were not optimized. For sake of comparison, the electro‐optic r₃₃ coefficient of our previously reported similar polymer functionalized with the well‐known Disperse Red One chromophore was also measured using the technique and gave a much lower r₃₃ coefficient. This study underscores that hyperbranched polymers are particularly promising matrices to host highly efficient chromophore to achieve more efficient and more stable electro‐optic devices than classical linear polymers. Copyright © 2013 John Wiley & Sons, Ltd.     

Synthesis of nonlinear optical maleimide copolymer by polymer reaction and their electro-optic properties

Thermally stable poly(α-methyl styrene-co-maleimide) (MSMI) and poly(α-methyl styrene-co-4-carboxyphenyl maleimide) (MSCM) substrate polymers were obtained readily by free radical polymerization of comonomers. Introduction of a DR1 chromophore to the maleimide units of MSMI substrate polymer by the Mitsunobu reaction was dependent on the reaction solvent. The degree of substitution of DR1 into the MSMI polymer was bound to be 91.1 mol % and 0.4 mol % by UV spectrometers in the THF and DMF solvent, respectively. DR1 chromophore was, however, substituted in the MSCM polymer at 33.0 mol % by Mitsunobu reaction in the THF solvent. Both substrate and NLO polymer exhibited high thermal stability due to the incorporation of maleimide units in the polymer chain. The glass transition temperature (T_g) and initial decomposition temperature (T_i) of the NLO polymer were in the range of T_g = 185°C and T_i = 310–345°C. The electro-optic coefficient (r₃₃) of NLO polymer was determined with an experimental setup capable of the real-time measurement while varying both the poling field and temperature. The NLO polymer MSMI-THF had a higher r₃₃ value than MSCM-DR due to an increased degree of substitution of DR1 chromophore. MSMI-THF had a maximum r₃₃ value of 16 pm/V at 135 MV/m poling field with a 632.8 nm light source. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3715–3722, 1999     

Preparation of polymer optical fibers doped with nonlinear optical active organic chromophores

We synthesized two novel organic nonlinear optical chromophores—chiral S(+)‐N‐[p‐(4‐nitrostyryl) phenyl] prolinol and non‐chiral [p‐(4‐nitrostyryl) phenyl] piperdine—as potential laser‐active dyes for photonic applications. Both materials show good optical transmittance in the telecommunication frequency region, desirable solubility in acrylic polymer optical fiber matrices, and attractive fluorescence properties that are advantageous for laser‐gain materials and devices. Subsequently, these two chromophores were incorporated into poly(methyl methacrylate) and poly(ethyl methacrylate) and drawn into polymer optical fibers. The relevant properties of these organic dye‐doped fibers have been studied, revealing essential attributes of laser‐active characteristics. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1794–1801, 2001     

Second harmonic generation and optical anisotropy of a spin-cast polymer film

The nonlinear susceptibilities (χ⁽²⁾₃₃, χ⁽²⁾₃₁), and the refractive index anisotropy, of a main chain accordion polymer, BCSC (see the text for the complete chemical formula), have been measured by the techniques of second harmonic generation (SHG) and waveguiding. A large birefringence, which is induced in the BCSC film by the spin-coating process, is almost removed by electric field poling. Our results demonstrate the fundamental difference between the birefringence associated with quadrupolar orientational order and the dipolar order associated with SHG. © 1993 John Wiley & Sons, Inc.     

Molecular design of nonlinear optical polymer based on DCM to enhance the NLO efficiency and thermal stability

This study synthesized and characterized a novel series of polyurethanes containing nonlinear optic (NLO) chromophores, which possess different dimensional or various isolation‐groups. These chromophores are based on 4‐(dicyanomethylene)‐2‐methyl‐6‐(p‐(dimethylamino)styryl)‐4H‐pyran (DCM‐typed dye). The NLO polyurethane containing a one‐dimensional isolation‐group of chromophores efficiently enhances thermal stability, but poling efficiency is not always improved as the size of isolation‐group increases. The enormous isolation group restrained the mobility of chromophore in the polymer matrix and shows a worsening SH intensity. The maximum second harmonic coefficient (d₃₃ = 68.7 pm/V) is displayed as benzene is attaching to chromophore moieties as isolation‐group in this study. Polyurethane containing two‐dimensional chromophore shows superior thermal stability due to the large volume required to rotate the chromophore in the polymer matrix. Two‐dimensional system exhibits lower SH intensity due to the rigid polymer main chain and twisted conjugated plane. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4937–4949, 2009     

Nonlinear optical material of a low-dimensional coordination polymer: Synthesis, structure, NLO and fluorescence properties

Employing unsymmetrical 2-mercapto-5-methyl-1,3,4-thiadiazole and 2,2′-bipyridine as mixed ligands, a new low-dimensional coordination polymer [Zn(MMTA) 2 (2,2′-bipy)] n (MMTA = 2-mercapto-5-methyl-1,3,4-thiadiazole, 2,2′-bipy = 2,2′-bipyridine), has been synthesized under solvothermal condition and characterized by single crystal X-ray diffraction. This compound crys- tallizes in the noncentrosymmetric space group Cc, with cell parameters: a = 8.291(4) , b = 15.483(9) , c = 15.620(6) , = 96.00(5)°, V = 1994.1(2) 3 , and Z = 4. The mixed ligands link the zinc center into a mononuclear unit, which is futher linked by weak C-H···N and C-H···S hydrogen bonds into a three-dimensional noncentrosymmetric framework. The compound exhibits intense photoluminescence and distinct NLO properties at room temperature. The intensity of the green light produced by the powder sample of the compound is about 3.2 times that produced by KDP powder. On the basis of the results of TG analysis, the structure is thermally stable up to ～260 °C.     

An optical reflected device using a molecularly imprinted polymer film sensor

A novel and highly selective optical sensor with molecularly imprinted polymer (MIP) film was fabricated and investigated. The optical sensor head employing a medium finesse molecularly imprinted polymer film has been fabricated and characterised. A blank polymer and formaldehyde imprinted polymer were using methacrylic acid as the functional monomer and the ethylene glycol dimethacrylate as a crosslinker. The transduction mechanism is discussed based on the changes of optical intensity of molecularly imprinted polymer film acting as an optical reflected sensor. Template molecules, which diffused into MIP, could cause film density, and refractive index change, and then induce measurable optical reflective intensity shifts. Based on the reflective intensity shifts, an optical reflection detection of formaldehyde was achieved by illuminating MIP with a laser beam. For the same MIP, the reflective intensity shift was proportional to the amount of template molecule. This optical sensor, based on an artificial recognition system, demonstrates long-time stability and resistance to harsh chemical environments. As the research moves forward gradually, we establish the possibilities of quantitative analysis primly, setting the groundwork to the synthesis of the molecular imprinted optical fiber sensor. The techniques show good reproducibility and sensitivity and will be of significant interest to the MIPcommunity.     

Interpenetrating polymer networks with stable second order nonlinear optical properties

Interpenetrating polymer networks (IPNs) based on polyurethane and polyacrylate-containing 4-(4'-nitrophenylazo) aniline chromophore groups were synthesized and characterized by infrared spectra, gel content and differential scanning calorimetry. Thin, transparent films of the IPNs were prepared by spin-coating, followed by thermal curing and corona poling. The poled IPN film shows very good optical properties and exhibits only one glass transition temperature. The second-order nonlinear optical (NLO) properties of the poled film were studied by visible light absorbance measurement according to one-dimensional rigid oriented gas model. The second-order nonlinear optical polarizability can reach 10^-7 e.s.u. The poled IPN film of defined composition showed a good temporal stability of NLO properties at 120°C for more than 160 hr.     

Effect of pressure and temperature on chromophore reorientation in a side-chain nonlinear optical polymer

Second harmonic generation (SHG) was used to measure the temperature dependence of the reorientation activation volume of the side-chain copolymer poly(disperse red 1 methacrylate-co-methyl methacrylate) (DR1-MMA). The decay of the SHG signal from poled films of DR1-MMA was recorded at hydrostatic pressures up to 3060 atm and at different temperatures between 25°C below the glass transition temperature (T_g) to 35°C above it. The activation volume, ΔV^*, decreased with increasing temperature. The data suggests that the coupling between chromophore reorientation and the long-range motion of the polymer is stronger for the DR1-MMA side-chain system than in previously measured guest–host systems. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2793–2803, 1998     

Synthesis and nonlinear optical properties of a novel indium phthalocyanine highly branched polymer

Due to the well‐known optical limiting properties of indium (III) phthalocyanines (In [III] Pcs) and aiming at extending their conjugation system, a highly branched indium phthalocyanine polymer was prepared. Flash chromatography was used for obtaining a pure polymer of polydispersity index near to the unity. The structure of the prepared polymer was determined using different spectroscopic techniques. Optical limiting and open aperture Z‐scan measurements were carried out according standard procedures. Compared with many other phthalocyanines, the prepared indium‐phthalocyanine polymer shows a high optical limiting performance that is indicated by a relatively low limiting threshold of 430 mJ cm^?2 and a large nonlinear absorption coefficient (α₂ = 3.4 × 10^?8 cmW^?1). Copyright © 2015 John Wiley & Sons, Ltd.     

Estimation of electrostriction coefficients of a nonlinear optical polymer electret

The effect of organic chromophores incorporated into a polymer electret and responsible for its nonlinear optical (NLO) response to an applied electric field on the electrostriction coefficients (ESC) of the material is studied. Analytical expressions for the ESC were derived in the framework of a model proposed earlier, which includes the effect of a locally anisotropic, polarizable and deformable environment on the electric characteristics of the chromophore. The dependence of the ESC on both macroscopic and microscopic parameters of the molecular system is established. Numerical estimates of the ESC for poly(methyl methacrylate) doped with the dye Disperse Red 1 and dimethylaminonitrostilbene-doped polycarbonate agree with experimental data in order of magnitude. The relations obtained can be used in the design of novel organic NLO materials. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 7, pp. 1324–1329, July, 2008.     

Synthesis and characterization of a novel non-linear optical (NLO) material

Anthracene is one of the organic molecular crystals, which exhibits peculiar optical and electronic properties. Since the 9, 10 positions are very reactive in anthracene, it undergoes the Diel’s–Alder reaction with maleic anhydride in 99% yield. The synthesis of Diel’s–Alder adduct has been carried out by adopting standard procedure. The product was subjected to various characterization studies such as FTIR, UV and ¹H NMR spectroscopy, and thermal studies to check its purity and determine the applicability of adduct in various applications. The second harmonic generation (SHG) efficiency of the adduct has been observed using Nd:YAG laser.     

新推拉型电光聚合物中间体的二阶NLO性质的分子设计研究

在能量梯度法（ＡＭ１）和间略微分重叠（ＺＩＮＤＯ）方法基础上,按完全态求和（ＳＯＳ）公式编制了计算分子二阶非线性光学（ＮＬＯ）系数βｉｊｋ,βμ的程序,研究了一系列新推拉型二分子的结构、光谱和二阶非线性光学系数β（２－ω,ω,ω）,β（ω,ω,ω）。考察一分子骨架,给、受电子取代基对βμ的影响及β与外场频率的关系。最后设计了最大βμ的电光聚合物中间体。     

Functionalized diacetylenes for nonlinear optical applications: Synthesis,characterization, and the properties of their monolayers

Synthesis and characterization of DA(8/1)OMe (14-{4′-[(methoxy)methoxy] biphenyl}-10,12-tetradecadiynoic acid) and DA(8/1)NBP (14-{4′-[(nitro)methoxy] biphenyl}-10,12-tetradecadiynoic acid ) are presented. Monolayers of DA(8/1)OMe at gas-water interface were investigated. It does not form a stable monolayer nor does it undergo polymerization at the gas-water interface. However, the Ba²⁺ and Cd²⁺ salts formed stable monolayer that polymerized. Polymerization was confirmed by Raman spectroscopy. The diacetylene analog with the more polar tail group, DA(8/1)NBP, does not form a monolayer and undergo polymerization regardless of the subphase condition. A mixed monolayer of DA(8/1)OMe and DA(8/1)NBP forms a true monolayer if the composition of DA(8/1)NBP is 50% or less. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1771–1779, 1999     

An optical image stabilisation using a droplet manipulation on a liquid crystal and polymer composite film

ABSTRACT

We demonstrate an image system with an optical image stabilisation using a droplet manipulation on a liquid crystal (LC) and polymer composite film (LCPCF) to reduce motion blur while preserve image quality. Such an image system adopts a liquid lens on an LCPCF and the mechanism is on a basis of droplet movement on LCPCF whose position changes because electrically tunable orientations of LC molecules on the surface of LCPCF. The change of position of the liquid lens compensates the deviation of light as the image system is under a handshake vibration. As a result, the image system under handshake vibrations could keep a clear image. The operating principles are introduced, and the experiments are performed and discussed. The concept in this paper can also be extended to design other optical components for modulating direction of light.     

PMMA型非线性光学膜的制备及其极化取向

采用封管反应, 以较高产率(80%以上)合成了一种PMMA型的极化非线性光学聚合物材料. 该材料具有很好的成膜性, 用电晕极化的方法使其旋涂膜中的生色团极化取向, 并利用偏振红外光谱和偏振紫外光谱等方法, 对膜中生色团极化前后的取向进行了研究.     

Theoretical studies on NLO properties of push-pull multi-cycle electro-optical polymer intermediates including thiophene ring

The second-order nonlinear optical susceptibilities βijk,βμ and third-order non-linear optical susceptibilities γijkl,<γ> of a series of the novel push-pull multi-ring electro-photo polymer intermediates have been calculated.The influences of molecular structure,donor,acceptor and the frequency of external field on P and v,and the relationship between V and the number of thiophene rings(i.e.conjugated chain length)have been studied using UNDO/SCI methods combined with sum-overstate(SOS)formula.The calculated results show that γ is proportional to 2.69 power of the chain length of the conjugated molecular bonds when the length is not quite long.     

Nonlinear optical (NLO) polymers. IV. Second‐order optical nonlinearity of NLO polyurea and copolyurea with NLO dipole moments aligned transverse to the main backbone

This article presents the molecular orientation and second‐order optical nonlinearity of newly prepared polyureas and copolyurea with dipole moments aligned transverse to the main backbone. Nonlinear optical (NLO) polyureas, TPU and TPU2, were prepared from 2,4‐diamino‐4′‐nitroazobenzene (2R‐DIAMINE) with 4,4′‐diphenylmethane diisocyanate (DMDI) and tolylene 2,4‐diisocyanate, respectively. NLO copolyurea was prepared from DMDI with 2R‐DIAMINE and m‐phenylene diamine. TPU and TPU2 gave d₃₃ values of 12.5 and 9.8 pm/V, respectively, under optimum poling conditions. A time‐dependent decay curve of second‐order nonlinear susceptibility was fitted well with a Kohlrausch–Williams–Watts stretched exponential function. The relaxation time of TPU2 was 4.2 × 10⁸ s at 100 °C. Copolyurea was uniaxially drawn in ratios of 1.5 and 2.0. The average molecular angles Φ_X , Φ_Y , and Φ_Z in three laboratory frames were evaluated from the refractive indices. Φ_Y decreased and Φ_X and Φ_Z increased with an increasing draw ratio. The dependence of the second‐order harmonic intensity on the incidence angle, that is, the Maker fringe pattern, was fitted with two independent tensor components, d₃₃ and d₃₁, for undrawn film and five independent tensor components, d₃₃, d₃₂, d₃₁, d₁₅, and d₂₄, for drawn films. For drawn films, Kleinman symmetry was not satisfied: d₃₁ ≠ d₁₅ and d₃₂ ≠ d₂₄. An increase in the draw ratio gave rise to a large increase in the tensor component d₃₃. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 247–255, 2001