Glass transition of thin films of poly(2-vinyl pyridine) and poly(methyl methacrylate): nanocalorimetry measurements

Glass transitions were observed in thin films of poly(2-vinyl pyridine) (P2VP) and poly(methyl methacrylate) (PMMA) using a scanning nanocalorimetry technique which has both high sensitivity (10⁻⁹ J/K) and high scan rates (10⁴-10⁵ K/s). Samples were deposited by the spin-cast method. The thickness of samples was 100-400 nm. Glass transition temperature, obtained by nanocalorimetry, is shifted toward higher temperatures by 10-20 K and activation enthalpy of glass transition is shifted to lower values by factor of 2-4. The glass transition characteristics of both polymers are discussed in terms of the standard Tool-Narayanaswamy-Moynihan (TNM) multi-parameter model.     

Degradation of poly(ethylene-co-methacrylic acid)-calcium carbonate nanocomposites

Composites of poly(ethylene-co-methacrylic acid) with 5 mass fraction percent of precipitated calcium carbonate nanoparticles were prepared by melt extrusion on a miniature melt-blender and medium-scale production equipment. The composites consisted mostly of isolated particles. The ultimate mechanical properties of the nanocomposites were consequently largely superior to composites with micron-sized filler. The calcium carbonate particles were shown to offer a large surface area for calcium salt formation during the thermal degradation of the material. This imparted a stabilizing effect to the copolymer that was comparable to the neutralization of the methacrylic acid units with calcium ions. The rate of calcium salt formation was fast at temperatures above 350 °C. Stearic acid surface coatings did not interfere significantly with the calcium salt formation. The oxidative stability of the composites was further largely improved by the formation of a diffusion barrier.     

The electrorheology of rigid rod poly(n-hexyl isocyanate) solutions

The electroviscosities of solutions of a lyotropic liquid crystalline polymer, poly(n-hexyl isocyanate), were investigated by a slit viscometer. The morphologies of the solutions being studied include the isotropic, the biphasic, and the fully liquid crystalline. All three morphologies exhibit viscosity enhancements with imposition of an electric field. However, the electrorheological behavior of the isotropic solution is different from those of other morphologies. The isotropic solution starts with a higher field free viscosity and its electroviscosity increases gradually with the increasing electric field strength. In contrast, the anisotropic solutions begin with lower zero field viscosities and the electroviscosities increase sluggishly until a critical field strength is reached; the viscosities then increase rapidly and finally exceed that of the isotropic solution. For the morphologies of the biphasic and the fully liquid crystalline, the dependence of the viscosity enhancements on field strength and shear rate can be described by a single variable. The variable scales with the square of the electric field strength and the reciprocal of the shear rate. By introducing the effect of the molecular permanent dipole moments into Doi's theory, the electrorheological effects of PHIC solutions can be satisfactorily interpreted. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 1217–1224, 1997     

The thermal transition behavior of poly(bis(p-flourophenoxy)phosphazene)

The thermal transition behavior of poly(bis(p-fluorophenoxy)phosphazene) was studied as a representative aryloxy-substituted poly(organophosphazene) using X-ray diffraction, differential thermal analysis and density measurements. The crystal structure of-form contained in as-cast film had marked paracrystalline disorder. The crystal phase transformed into the mesophase atT(1) (110 140 °C). The structure of the-form observed in the mesophase was a representative hexagonal-packing of macromolecular chains which rotate around the chain axes. When the mesophase was cooled to room temperature, a more ordered crystal phase of the-form could appear. The most ordered crystal structure of the-form has a monoclinic unit cell with the following lattice parameters: a=18.9, b=13.2, c=4.90 Å, and=77°. The chain conformation is nearly planar cis-trans, which has been observed commonly in poly(organophosphazenes). The macroscopic deformation of the film sample was also examined, taking into account the microscopic deformation of the lamellar crystal due to the crystal-mesophase transition.     

Effect of poly(vinyl acetate) (PVAc) on thermal behavior and mechanical properties of poly(3-hydroxybutyrate)/poly(propylene carbonate) (PHB/PPC) blends

To assess the compatibility of blends of synthetic poly(propylene carbonate) (PPC), with a natural bacterial poly(3-hydroxybutyrate) (PHB), a simple casting procedure of blend was used. poly(3-hydroxybutyrate)/poly(propylene carbonate) blends are found to be incompatible according to DSC and DMA analysis. In order to improve the compatibility and mechanical properties of PHB/PPC blends, poly(vinyl acetate) (PVAc) was added as a compatibilizer. The effects of PVAc on the thermal behavior, morphology, and mechanical properties of 70PHB/30PPC blend were investigated. The results show that the melting point and the crystallization temperature of PHB in blends decrease with the increase of PVAc content in blends, the loss factor changes from two separate peaks of 70PHB/30PPC blend to one peak of 70PHB/30PPC/12PVAc blend. It is also found that adding PVAc into 70PHB/30PPC blend can decrease the size of dispersed phase from morphology analysis. The result of tensile properties shows that PVAc can increase the tensile strength and Young’s modulus of 70PHB/30PPC blend, and both the elongation at break and the tensile toughness increase significantly with PVAc added into 70PHB/30PPC.     

Modulated calorimetry of poly(1,4-oxybenzoate), poly(2,6-oxynaphthoate), and their copolymers

Poly(1,4-oxybenzoate) (POB) and poly(2,6-oxynaphthoate) (PON) and their copolymers which have a well-established phase diagram have been studied with temperature-modulated differential scanning calorimetry (TMDSC). All the analyzed polymers have more than one disordering transition between the glass transition (from 400 to 430 K) and decomposition (starting at ≈700 K). Above the glass transition, the reversible heat capacity, C_p, increases beyond that calculated from the crystallinity and the known C_p of the solid and melt. This is likely due to an increase of mobility within the crystals and/or a possible rigid-amorphous fraction (mainly for the copolymers). The disordering transitions are largely irreversible, supporting the observation that semicrystalline, linear macromolecules show decreasing amounts of locally reversible melting with increasing rigidity and crystal perfection.     

The role of water in structural changes of poly(N-isopropylacrylamide) and poly(N-isopropylmethacrylamide) studied by FTIR, Raman spectroscopy and quantum chemical calculations

Temperature-induced phase transition in water solutions of poly(N-isopropylacrylamide) (PNIPAM) and poly(N-isopropylmethacrylamide) (PNIPMAM) have been studied by ATR FTIR and Raman spectroscopy in combination with quantum chemical calculations. The presence or absence of the α-methyl group has a strong effect on the physical structure of water solutions. Although the hydrophobic interactions for PNIPMAM and PNIPAM are very similar, PNIPMAM with additional methyl group exhibits significantly weaker intermolecular interactions between the amide groups. That effect is the cause of the higher transition temperature T_t by about 8 °C for PNIPMAM compared to PNIPAM due to the formation of larger compact structures. The presence of the methyl group is significant for the reversibility of the temperature transition during the backward cooling as the dissolution of more stable compact PNIPMAM requires overcoming of a higher energy barrier and shows a strong hysteresis.     

Thermoresponsive poly(N-isopropylacrylamide) nanogels/poly(acrylamide) nanostructured hydrogels

Here we report the preparation and characterization of nanostructured thermo-responsive poly(acrylamide) (PAM)-based hydrogels. The addition of slightly crosslinked poly(N-isopropylacrylamide) (PNIPA) nanogels to AM reactive aqueous solution produces nanostructured hydrogels that exhibit a volume phase transition temperature (T_VPT). Their swelling kinetics, T_VPT's and mechanical properties at the equilibrium-swollen state (H_eq) are investigated as a function of the concentration of PNIPA nanogels in the nanostructured hydrogels. Nanostructured hydrogels with PNIPA nanogels/AM mass ratios of 20/80 and above exhibit higher H_eq and longer time to reach the equilibrium swelling than those of the conventional PAM hydrogels. However, the PNIPA nanogels possess thermo-responsive character missing in conventional PAM hydrogels. The T_VPT of nanostructured hydrogels depends on PNIPA nanogel content but their elastic and Young moduli are larger than those of conventional hydrogels at similar swelling ratios. Swelling kinetics, T_VPT, and mechanical properties are explained in terms of the controlled in-homogeneities introduced by the PNIPA nanogels during the polymerization.     

Mechanism for the phase transition of poly(butylene terephthalate)

The α and β forms of poly(butylene terephthalate) transform reversibly by elongation and relaxation. The conformation change occurs in the tetramethylene glycol part, from GGTGG conformation to TSTS?T conformation. In this study, by using a doubly oriented sample, we measured the positions, intensities, and half‐widths of the (100) and (010) reflections of the α and β forms of poly(butylene terephthalate) with a position‐sensitive proportional counter system. During the transformation, the molecules translate only slightly. These slight molecular translations, or distortions, accumulate, and the crystallite of the α form breaks into the small crystallites of the β form as the α–β transformation proceeds, and the crystallite of the α form grows with the relaxation of the distortion accumulated in the crystal and amorphous regions and on the crystallite surface as the β–α transformation proceeds. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 765–771, 2002     

Determination of the glass transition temperature of polystyrene,poly(vinyl chloride) and poly(methyl methacrylate) using gas chromatography

The glass transition temperatures, Tg, of polystyrene, poly (vinyl chloride) and poly(methyI methacrylate) have been determined from gas chromatographic measurements using n-hexane, n-heptane, meta-xylene and para-xylene solvents. The glass transition temperatures were detected on the z-shaped retention diagrams which were produced from the plot of the logarithm of the specific retention volumes of the above-mentioned solvents against the reciprocal of temperature, i.e. log V${}_{\text{g}}^{\text{º}}$ vs. 1/T. The glass transition temperature is specified by the temperature where the slope of log V${}_{\text{g}}^{\text{º}}$ vs. 1/T changes abruptly. The observed glass transition temperature of polystyrene produced by this technique was found to be in good agreement with those produced by other techniques such as the differential scanning colorimeter. The industrial importance of the glass transition temperature, T_g, might be due to the dramatic changes in the physical properties of the polymer, such as hardness and elasticity, which take place in the vicinity of this temperature. However, perfectly crystalline polymers do not exhibit glass transitions, because their chains are incorporated in regions of three-dimensional order, called crystallites. Completely amorphous polymers and semi-crystalline polymers usually exhibit both glass transition and melting.     

Coil-to-globule-type transition of poly(N-isopropylacrylamide) adsorbed on colloidal silica particles

 The temperature dependence of the dimensions of poly(N-isopropylacrylamide) (PNIPAM) adsorbed on two different colloidal silica particles was studied with dynamic light scattering. The hydrodynamic diameter was measured when the temperature was varied stepwise from 10 to 60 °C. PNIPAM molecules free in solution undergo a conformational transition at the θ temperature. We have found that PNIPAM adsorbed onto silica particles also undergoes a transition below the θ temperature. When a small amount of polymer was adsorbed the coil-to-globule transition at the θ temperature did not occur. Potentiometric titrations showed that the surface charge of the silica particles was not affected by the polymer adsorption. Sodium dodecyl sulfate (SDS) (100–1200 mg/l) was added to improve the stability. The particles with a higher zeta potential required a smaller addition of SDS to prevent coagulation compared to the particles with a smaller surface potential. For low additions of SDS the transition curves of adsorbed PNIPAM were unaffected. For larger additions of SDS the collapse of PNIPAM was shifted to higher temperatures. When as much as 1200 mg/l SDS was added, two regions with weak transitions were observed before the collapse. It was also observed that the presence of SDS results in a smaller adsorption of PNIPAM onto the particles. The addition of SDS strongly increased the magnitude of the electrophoretic mobility of the polymer–particle unit. From the electrophoretic measurements an electrokinetic layer thickness was calculated and it was found to be smaller than the corresponding hydrodynamic layer thickness, as obtained by dynamic light scattering. Received: 14 December 1999/In revised form: 22 February 2000/Accepted: 6 March 2000     

Novel well-defined star homopolymers and star-block copolymers of poly(n-hexyl isocyanate) by anionic polymerization

Anionic polymerization high-vacuum techniques and appropriate multifunctional initiators/additives were employed for the synthesis of novel star structures of poly(n-hexyl isocyanate) (PHIC). A new trifunctional initiator prepared by the reaction of tris(4-isocyanatophenyl)methane with benzyl sodium was used for the synthesis of three-arm star PHIC. Divinyl benzene and the core-first or the arm-first/core-first (in-out) approach were utilized for the synthesis of multiarm star homopolymers, (PHIC)_n, star-block copolymers, (PHIC-b-PI)_n, and miktoarm star copolymers, (PS)_n(PHIC)_n, where PS is polystyrene. The molecular characteristics obtained by size-exclusion chromatography, equipped with refractive index and two-angle light scattering detectors, nuclear magnetic resonance, spectroscopy, and dilute solution viscometry showed that well-defined structures were synthesized in this study. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2387–2399, 2007     

Oxidative and photooxidative degradation of poly(acrylic acid)

The oxidative degradation of poly(acrylic acid) (PAA), a water soluble polymer, was studied at various temperatures with different concentrations of persulfates, potassium persulfate (KPS), ammonium persulfate (APS) and sodium persulfate (SPS). The photodegradation of PAA was also examined with APS as oxidizer. The degraded samples were analyzed for the time evolution of molecular weight distribution by gel permeation chromatography. A theoretical model based on the continuous distribution kinetics was developed that accounted for the polymer degradation and the dissociation of persulfate. The rate coefficients for the oxidative and photooxidative degradation of PAA were determined from the parametric fit of the model with experimental data. The rate of degradation increased with increasing amount of persulfate in both oxidative and photooxidative degradation. The rate of degradation also increased with increasing temperature in the case of oxidative degradation.     

Synthesis and degradation behavior of poly(ethyl cyanoacrylate)

Poly(ethyl cyanoacrylate) was synthesized using N,N′-dimethyl-p-toluidine as an initiator through an anionic/zwitterionic pathway. The degradability and the degradation mechanism of the prepared polymer were examined from various viewpoints. A combination of TGA and GPC analysis allowed us to confirm that the thermal degradation of this polymer was predominantly due to an unzipping depolymerization process initiated from the polymer chain terminus. The polymer was inherently unstable and exhibited interesting degradation behavior in solution with basic reagents. The degradation in solution was also found to be attributed to the unzipping of the monomer from the chain end. However, the degradation behavior of the polymer could be controlled by changing solvents, temperatures, and additives. These findings give an insight into the degradation behavior of poly(alkyl cyanoacrylate)s, which is a crucial point in utilizing these polymer homologues for various applications.     

In vitro release of protein from poly(butylcyanoacrylate) nanocapsules with an aqueous core

Factors influencing the in vitro release of bovine serum albumin (BSA) from poly(butylcyanoacrylate) (PBCA) nanocapsules, such as the pH value, BSA loading, the polymeric nanocapsule walls and protein molecular weight, were investigated in detail. The BSA release rate was affected by the degradation rate of the polymeric wall and protein loading. For low molecular weight proteins, the initial burst release was faster than that of high molecular weigh proteins and got to equilibrium quickly. Sodium dodecyl sulfate–polyacrylamide gel electrophoresis results showed that BSA encapsulated within PBCA nanocapsules did not suffer covalent aggregation or fragmentation during the initial days of in vitro incubation. For nanocapsules prepared by interfacial polymerization in water-in-oil microemulsions, these findings were useful as a foundation for the development of nanocapsules with desired properties.     

Some composting and biodegradation effects of physically or chemically crosslinked poly(lactic acid)

Polylactide (PLA) crosslinked by using both triallyl isocyanurate (TAIC) and electron radiation or using dicumyl peroxide (DCP) was studied with the aim of examining the behaviour of the modified polymer under various environmental conditions. Thus, the polymer samples were subjected to composting in an industrial pile, exposed to proteinase K, or incubated in sea water. The number-average molecular weight (M_n), melt flow index (MFI), crystallinity (χ), tensile strength (σ_M) and mass loss (in the case of samples treated with proteinase K) were determined. It was found that neat PLA irradiated with high-energy electrons underwent degradation that increased during composting. As a result, the value of M_n of this polymer dramatically decreased. It appeared that PLA crosslinked with TAIC and electron radiation contained, in addition to the crosslinked phase, a phase strongly degraded by this radiation, which facilitated hydrolytic degradation during composting. The σ_M value of PLA crosslinked with TAIC and electron radiation rapidly decreased during composting, whereas that of PLA crosslinked chemically and composted for three weeks slightly increased. As the electron radiation dose increased, the mass loss of PLA containing TAIC and treated with proteinase K decreased, which indicated that the physical crosslinking of PLA hindered enzymatic degradation of this polymer. Important changes in both neat and physically crosslinked PLA incubated in sea water for nine weeks were not detected.     

Properties of nanometric and submicrometric multilayered films of poly(3,4-ethylenedioxythiophene) and poly(N-methylpyrrole)

Multilayered films formed by 3, 5 and 7 alternated layers of poly(3,4-ethylenedioxythiophene) and poly(N-methylpyrrole) have been prepared by chronoamperometry under a constant potential of 1.4 V using a layer-by-layer electrodeposition technique. In order to examine influence of the interface:bulk dimensional ratio, the thickness of the yielded films was reduced from the submicrometric to the nanometric scale by decreasing the polymerization time of each layer from 100 s to 10 s. The electroactivity, electrochemical characteristics and morphologies of the resulting multilayered films have been compared with those obtained for both single-component poly(3,4-ethylenedioxythiophene) films prepared using identical experimental conditions and previously reported multilayered films with thickness within the micrometric scale [Estrany F, Aradilla D, Oliver R, Alemán C. Eur Polym J 2007;43:1876].     

Thermal degradation of poly(vinyl chloride) synthesized with a titanocene catalyst

PVC was synthesized using a trichloroindenyltitanium-methylaluminoxane catalyst at room temperature, and its degradation was monitored along with a commercial sample at 160, 170 and 180 °C under air or nitrogen atmosphere. The process was followed by HCl evolution, yellowing index, colour formation and thermogravimetric analysis. The produced polymer had a lower molecular weight and higher surface area, compared with a commercial PVC, while ¹H NMR and T_g values show minimal differences between materials. The HCl evolution degradation studies indicate that produced PVC has a lower thermal resistance than commercial PVC, while TGA reveals the opposite behaviour. Yellowing index and colour evaluation give evidence that nitrogen atmosphere and high surface area in produced PVC allow the polyene growth, whereas low surface area and air atmosphere generate shorter polyenes and chromophoric species. Differences in degradation performance are thought to be due to chemical origin, inherent morphology and differences in instrumentation.     

Novel degradable copolyesters containing poly(ethylene oxalate) units derived from diethylene oxalate

Two series of poly(ethylene terephthalate-co-oxalate-co-sebacate) (PETOXS) have been synthesized by melt polycondensation using diethylene oxalate (DEOX) as a starting material. NMR quantified the composition, structure, and average sequence length of the copolyesters. Melting and crystallization properties differ from each other on the basis of PETOXS feature. Analysis of TG traces determined that initial degradation temperatures were affected by the content of PET. It was observed that the Young's modulus and the maximum tensile stress increased with increasing content of poly(ethylene oxalate) (PEOX) in aliphatic units, whereas the elongation at break considerably decreased. Obvious weight loss was observed in alkali hydrolysis experiments, and the degradation rates are subject to distinct factors when the ratio of two aliphatic polyester units is varied. DSC was performed to degraded copolyester samples, and the variation of melting temperature and crystallinity were investigated.     

Degradation mechanism of poly(lactic-co-glycolic) acid block copolymer cast films in phosphate buffer solution

We have investigated the degradation of poly(lactic-co-glycolic) acid copolymer with a lactic to glycolic ratio of 50:50. Solvent-cast films were incubated at 37 °C in phosphate buffered saline solution and their degradation was followed using potentiometry, light microscopy, gravimetry, size exclusion chromatography, differential scanning calorimetry and infrared spectroscopy. The degradation process was found to have two main steps. The first step was observed from 0 to 7 days of degradation. During the first few days a soft layer formed at the surface of the film. As degradation time increased this soft surface layer was found to swell and wrinkle. The polymer molecular weight in the bulk was found to decrease as soon as the film was placed in the medium while the polymer present in the surface layer was found to degrade at a much slower rate. The second step of degradation was found to occur after 8 days. At this stage of the degradation process the molecular weight of the polymer in the bulk of the films was so low that the materials became liquid resulting in the detachment of the film from the glass slide. At this stage the mass loss and amount of acid released in the media were found to increase significantly.