Surface chemical analysis and chromatographic characterization of polyethylenimine-coated hydroxyapatite with various amount of polyethylenimine

Polyethylenimine (PEI) has been widely used as a coating material to produce stationary phase for ion-exchange chromatography of biomolecules. However, a precise study of the PEI coating fraction has been lacking, despite such quantification being very important for fundamental research as well as identifying further industrial applications.In this study, we produced four types of PEI-coated hydroxyapatite (PEI-HAp) with various fractions of PEI (0.16%, 0.5%, 1.0%, 1.5%) using a spray-drying system to evaluate correlations between coating fractions and the thermochemical or chromatographic behaviors of theses products. The thermal analyses of these matrices showed two exothermic peaks when the PEI coating fraction exceeded 1.0%. The one peak indicated a PEI decomposition peak and the other would indicate bond dissociation of PEI layers formed over the HAp surface as the PEI concentration increased. Furthermore, the chromatographic analysis for the surface chemical characteristics showed the correlation between coating fraction and the retention time of protein or nucleotide. Acidic or phosphorylated proteins were more strongly adsorbed as the PEI coating fraction increased when the initial coating fraction was low, but at fraction exceeding 0.5%, constant retention was observed. The retention time of nucleotides increased in proportion to the fraction of PEI added. The good selectivity of PEI-HAp may be attributable to multifunctional interactions of electrostatic and bare Ca sites on HAp, not just the amino sites of PEI. These precise studies of PEI coating fraction are our original novel contributions, which could be achieved by quantitative consideration using thermal analysis and chromatography.     

One-Step Synthesis of Polyethylenimine-Coated Magnetic Nanoparticles and its Demulsification Performance in Surfactant-Stabilized Oil-in-Water Emulsion

In this study, polyethylenimine (PEI)-coated Fe₃O₄ magnetic nanoparticles (MNPs) were successfully synthesized via a one-step, solvo-thermal method. The synthetic PEI-coated MNPs were characterized by using multiple techniques and their demulsification efficiencies were evaluated in surfactant-stabilized, oil-in-water emulsions. The results showed that the synthesized MNPs successfully adsorbed to the emulsion’s O/W interfaces and, consequently, the oil droplets could be rapidly destabilized under an applied magnetic field. It was found that the demulsification efficiency was enhanced with the increased particle dosage. The opposite effect was found with the increase in pH value and surfactant concentration. The presence of electrolytes facilitated oil removal, presumably by reduction of the electrostatic repulsion or by altering the hydrophobicity of the MNPs. Recovery experiments at various pH levels indicated that the PEI-coated MNPs could be reused for up to ten times without significant reduction in demulsification efficiency. Altogether, the results suggested that the PEI-coated MNPs could provide a simple but powerful tool to remove emulsified oil from aqueous systems.     

Gold nanoparticles prepared using polyethylenimine adsorbed onto montmorillonite

Polyethylenimine-modified montmorillonite (N-MMT) was used to prepare gold nanoparticles, where the montmorillonite (MMT) acted as a solid support to retain the conformation of polyethylenimine (PEI), and the amino groups of PEI were used simultaneously to both complex and reduce the gold ions. From the results of X-ray diffraction, it is apparent that the reduction of gold ions occurs primarily on the MMT surface. In the presence of MMT, the formation of a flattened configuration on the clay instead of stretched-out ethylenimine segments of PEI results in the formation of smaller gold particles. With a higher acidification ratio, the recharging of the MMT surface with positive ammonium ionic sites of PEI is likely to prevent the flocculation of clay and thus facilitate the reduction of gold. The rate of gold reduction with N-MMT is faster at low pH values, this being in contrast to the usual trend observed for the reduction of gold ions. The use of PEI adsorbed onto MMT has been shown to be able to act simultaneously as both a protective template and as a reducing agent, thereby greatly simplifying the process for preparing gold nanoparticles.     

Effect of Water Hardness on Catechin and Caffeine Content in Green Tea Infusions

The health benefits of green tea are associated with its high catechin content. In scientific studies, green tea is often prepared with deionized water. However, casual consumers will simply use their local tap water, which differs in alkalinity and mineral content depending on the region. To assess the effect of water hardness on catechin and caffeine content, green tea infusions were prepared with synthetic freshwater in five different hardness levels, a sodium bicarbonate solution, a mineral salt solution, and deionized water. HPLC analysis was performed with a superficially porous pentafluorophenyl column. As water hardness increased, total catechin yield decreased. This was mostly due to the autoxidation of epigallocatechin (EGC) and epigallocatechin gallate (EGCG). Epicatechin (EC), epicatechin gallate (ECG), and caffeine showed greater chemical stability. Autoxidation was promoted by alkaline conditions and resulted in the browning of the green tea infusions. High levels of alkaline sodium bicarbonate found in hard water can render some tap waters unsuitable for green tea preparation.     

Flocculation of Bacillus amyloliquefaciens H Disintegrates with Cationized Starch and Aminated Hydroxyethylcellulose

The ability of cationized hydroxyethylated starch (CHES) and aminated hydroxyethylcellulose (DEAE-HEC) to flocculate cell disintegrate of Bacillus amyloliquefaciens H (BamHI) was investigated. The efficiency of flocculation was compared to that of synthetic polymer polyethyleneimine (PEI) and natural polysaccharide chitosan. The influence of salt concentration and biomass concentration on flocculation efficiency was investigated. It was found that the efficiency of flocculation with CHES and DEAE-HEC was similar to that of PEI but better compared to chitosan. Recovery of total soluble proteins at higher than 0.3% concentration of flocculant decreased by more than 18.8% and 42.3% compared to PEI and chitosan, respectively. The yield of BamHI restriction endonuclease activity with all flocculants was similar except for chitosan where 13.1% lower yield was obtained. Meanwhile, efficiency of flocculation with CHES and DEAE-HEC depends drastically on the salt concentration, that is, flocculation diminishes if NaCl concentrations higher than 0.2 M (for CHES) or 0.1 M (for DEAE-HEC) are used. The results have shown that CHES and DEAE-HEC are promising flocculants of cell disintegrates if higher yield of protein is of great concern.     

Organo-modified cationic silica nanoparticles/anionic polymer as flocculants

The synthesis of quaternized silica nanoparticles and its application to fine clay flocculation were investigated. N-trimethoxysilylpropyl-N,N,N-trimethylammonium chloride was used as a cationic reagent to introduce quaternary amine groups onto the surfaces of silica nanoparticles via the formation of covalent bonds between the methoxy groups of the cationic reagents and the silanol groups in the silica surface. The zeta potential, zeta, and charge density of the silica particles modified under various reaction conditions were determined. Dynamic clay flocculation experiments using a photometric dispersion analyzer (PDA) showed that the cationic silica alone contributed little to the flocculation. However, the cationic silica, in conjunction with an anionic polymer of high M(w) and low charge density, led to a significant improvement in the flocculation of fine clay particles. The mechanism of flocculation was explored by a systematic investigation of interaction between cationic silica and anionic polymers as well as of their adsorption behavior on clay surfaces. The influence of factors such as pH and electrolyte concentration on clay flocculation was also investigated.     

Interaction of Sodium Dodecyl Sulfate with Poly(ethyleneimine) in Bulk Solution and at the Air-Solution Interface

Interaction of sodium dodecyl sulfate (SDS) with the cationic polyelectrolyte poly(ethyleneimine) (PEI) was investigated in this study. Turbidity measurements were performed in order to analyze the interaction and complex formation in bulk solution as a function of polymer concentration and pH. Surface tension measurements were made to investigate the properties of SDS/PEI/water mixtures at air/solution interface. Results revealed that SDS/PEI complexes form in solution depending on the surfactant and polymer concentration. A decrease was observed in surface tension values in the presence of SDS/PEI mixtures compared to the values of pure SDS solutions. Both solution and interfacial properties exhibited pH dependent behavior. A shift was seen in the critical micelle concentration of SDS solutions as a function of PEI concentration and solution pH. Monovalent and divalent salt additions showed some influence on the interfacial properties of SDS solutions in the presence of PEI.     

Preparation and characterization of different polyelectrolyte complexes and their application as flocculants

 Polyelectrolyte complexes (PEC) from poly(diallyl-dimethyl-ammoniumchloride) PDADMAC and two different polyanions, formed in aqueous solution, were characterized by different methods (zeta-potential, net content, turbidity) and applied as flocculants. The flocculation of clay was investigated by sedimentation measurement as well as by a dynamic method, using a Fibre Optical Flocculation Sensor. The results of both methods showed that the most important advantages of PEC were the high velocity of sedimentation and a very broad range of the optimum flocculation concentration. In spite of the differences in the complex-forming behavior of the two polyanions used, no significant differences between complexes of the same composition but different polyanions are obtained. In contrast, the ratio of anionic to cationic charges is of great importance for the mechanism of flocculation. Received: 30 May 1997 Accepted: 22 September 1997     

Stability of low levels of perchlorate in drinking water and natural water samples

Perchlorate ion (ClO₄⁻) is an environmental contaminant of growing concern due to its potential human health effects, impact on aquatic and land animals, and widespread occurrence throughout the United States. The determination of perchlorate cannot normally be carried out in the field. As such, water samples for perchlorate analysis are often shipped to a central laboratory, where they may be stored for a significant period before analysis. The stability of perchlorate ion in various types of commonly encountered water samples has not been generally examined—the effect of such storage is thus not known. In the present study, the long-term stability of perchlorate ion in deionized water, tap water, ground water, and surface water was examined. Sample sets containing approximately 1000, 100, 1.0, and 0.5 μg l⁻¹ perchlorate ion in deionized water and also in local tap water were formulated. These samples were analyzed by ion chromatography for perchlorate ion concentration against freshly prepared standards every 24 h for the first 7 days, biweekly for the next 4 weeks, and periodically after that for a total of 400 or 610 days for the two lowest concentrations and a total of 428 or 638 days for the high concentrations. Ground and surface water samples containing perchlorate were collected, held and analyzed for perchlorate concentration periodically over at least 360 days. All samples except for the surface water samples were found to be stable for the duration of the study, allowing for holding times of at least 300 days for ground water samples and at least 90 days for surface water samples.     

Influence of humic acid on the flocculation of clay

The aim of this study was to improve the flocculation of wastewater from gravel pits, especially the separation of the finely dispersed inorganic particles and the removing of humic acid. Clay was used as a model to investigate the influence of humic acid on the flocculation with two different types of polycation. The dependence of the sedimentation behaviour on time was investigated as well as the turbidity of the supernatant and the light absorption as a measure for humic acid removal. Bridging of particles remained the dominant mechanism of particle destabilisation by treating the clay in water with cationic polyacrylamides of very high molecular mass (CPAM). Poly(diallyldimethylammonium chloride) (PDADMAC) of lower molar mass (35 000 g/mol) was found to act by charge neutralisation. In this case the so-called flocculation window was very small. This behaviour is the same for systems containing humic acid. However, the need for cationic flocculant increases because humic acid as a weak polyanion can interact with the polycation. By using CPAMs with low charge this interaction does not play a significant role. The optimum flocculation concentration is relatively high. The flocs are larger and the velocity of sedimentation is higher than for the short-chain and highly charged polycation PDADMAC. However, because the latter is more effective in removal of humic acid at the point of optimum flocculation it is more advantageous to combine the highly charged polycation with a high molecular weight polyanion (dual system).     

Hydrophobic Flocculation of Galena Fines in Aqueous Suspensions

The hydrophobic flocculation of galena fines induced by potassium amyl xanthate (PAX) in aqueous suspensions has been studied using laser diffraction, electrophoretic light scattering, contact angle, and microflotation measurements. The measurements were performed on <2 μm, 2-5 μm, 5-10 μm, and <30 μm size galena by varying several parameters, including PAX concentration, pH, original particle size, kerosene concentration, and suspension stirring. The experimental results have demonstrated that the hydrophobic flocculation was closely correlated with the particle hydrophobicity, but was not lowered upon increasing the particle surface charges due to PAX adsorption, which is contrary to the DLVO theory. This flocculation has been observed to increase with a reduction of the original particle size and an increase in kerosene concentration, and to require sufficient stirring strength and magnitudes of kinetic energy input to achieve the maximum aggregation degree. From the microflotation results, it has been found that the flotation response of galena fines is markedly improved due to the formation of hydrophobic flocs, suggesting that floc flotation is a promising means to recover galena in the fine size range. Copyright 2000 Academic Press.     

Isolation and Characterization of Cellulosic Pulp Fines and Their Interactions with Cationic Polyacrylamides

Four different types of cellulosic fines were isolated from refiner mechanical and kraft pulp samples to characterize their chemical and physical properties. The pulp fines were flocculated using four different types of cationically modified polyacrylamides. The extent of flocculation was observed with multiple light scattering apparatus. The maximum adsorption of the polyelectrolytes on the pulp fines was determined by polyelectrolyte titration. It was concluded that it is the combination of the molar mass and the charge density of a polyelectrolyte, as well as the origins and characteristics of the fines which define the adsorption and flocculation behavior. None of these properties alone could fully describe these phenomena, but the molar mass of the polyelectrolyte was the predominant factor. The most important fines characteristics were the charge properties and the microstructure.     

Synthesis of a new flocculant based on poly(acrylamide-co-(N-octyl-4-vinylpyridinium bromide)) [AM5/VP5C8Br]-application for the turbidity removal from clay suspension

The interactions between poly(acrylamide-co-(N-octyl-4-vinylpyridinium bromide)) [AM5/VP5C8Br] cationic polyelectrolyte, and clay particles in dilute aqueous suspensions are studied in the aim of adsorption and flocculation. The extents of both phenomena are significantly influenced by the ionic strength of the medium. The adsorption of the clay particles on the copolymer chains occurs initially by the hydrophobic interaction. As flocculation mechanisms, the hydrophobic interaction between copolymer chains and the clay particles appears to be principal. In this work, we have prepared a copolymer which has been characterized by conductivity, viscosity, ¹H NMR, and FT-IR spectroscopies. The copolymer dosage and pH are two of the most important experimental parameters in the coagulation/flocculation operations used for study and optimization of the wastewater treatment operations. Under optimized conditions, 97% efficiency of the turbidity elimination, with a very low flocculant concentration of 3?ppm have been achieved in order to produce drinking water with standard limits around the world (< 1 NTU). The conclusion drawn on the basis of these results is that wastewater treatment using this new copolymer [AM5/VP5C8Br] has proved to be a good flocculant in overseeing of wastewater turbidity problems.     

Electrochemical decomposition of layer-by-layer thin films composed of TEMPO-modified poly(acrylic acid) and poly(ethyleneimine)

The decomposition of layer-by-layer (LbL) thin films composed of 2,2,6,6-tetramethylpiperidine-1-oxyl free radical-appended poly(acrylic acid) (TEMPO-PAA) and poly(ethylenimine) (PEI) was studied by using a quartz crystal microbalance (QCM) and cyclic voltammetry. The electrode potential of the (PEI/TEMPO-PAA)₄/PEI film-coated Au resonator was scanned from +0.2 to +0.8 V vs Ag/AgCl. The CV showed that the oxidation peak current decreased as the number of scans increased. The change in the resonance frequency of the QCM increased after electrolysis, indicating that the film was decomposed by electrolysis. The positive charges originating from the oxoammonium ions probably destabilized the (PEI/TEMPO-PAA)₄/PEI film. Furthermore, the release of 5,10,15,20-tetraphenyl-21H,23H-porphine tetrasulfonic acid (TPPS) from TPPS-loaded (PEI/TEMPO-PAA)₄/PEI-coated ITO electrodes was investigated. TPPS was released at electrode potentials greater than +0.6 V by the decomposition of the film. The results suggest that TEMPO-PAA/PEI LbL films are suitable for electrochemically controlled drug delivery systems.     

Visual detection of Al ions using conjugated copolymer-ATP supramolecular complex

A colorimetric Al³⁺ sensor based on fluorescence recovery of a conjugated copolymer-ATP complex is proposed. An optimized ratio of two polythiophene (PT) monomers is utilized to synthesize copolymer (CP) that yielded maximized colorimetric response for Al³⁺ in deionized (DI) and tap water. The electrostatic disassembly of CP-ATP upon addition of Al³⁺ led to an evident visual color change. The lowest concentration of Al³⁺ for naked eye observation is around 4 μM, which is below the threshold levels in drinking water according to European Economic Community (EEC) standard. Besides, the proposed assay showed a similar response to Al³⁺ in tap water. The proposed methodology showed selective and sensitive detection for Al³⁺ in analytically relevant concentration ranges without involving sophisticated instrumentation, illustrating the applicability for on-site drinking water monitoring.     

Electrically induced lipid migration in non-lamellar phase

Inverted hexagonal blocks of 1,2-dioleoyl-sn-glycero-3-phosphoethanolamine (DOPE) lipid adsorbed on a polyethyleneimine (PEI)-coated surface in deionized water transformed its shape upon the application of an electric field, forming lipid objects in a variety of shapes (e.g. lines with a width of 10-50μm). The phenomenon was driven by the electrophoresis, because the zwitterionic lipid, DOPE turned out to be highly negatively charged in deionized water. The interaction between DOPE and the PEI surface stabilized the system, assuring a lifetime over several weeks for the formed structures after the electric field was switched off. The free-drawing of microscopic objects (lines, crosses, and jelly fish) was also achieved by controlling the direction of the lipid movement with the field direction.     

Bridging flocculation of PEI-functionalized latex particles using nanocrystalline cellulose

Polystyrene microspheres were functionalized by covalent binding of 250 kDa linear PEI and ethanolamine, acting as a blocking agent, through bioconjugation with EDAC. The functionalized spheres were found to become less susceptible to salt-induced flocculation due to electrosteric stability, caused by the PEI chains at low NaCl concentrations, and at high salt concentration, by steric repulsion by the ethanolamine layer, which in combination with van der Waals attraction results in a shallow energy minimum and the formation of a few unstable aggregates. The latex aggregated in the presence of nanocrystalline cellulose (NCC) with varying efficiencies, depending on the ratio of NCC to latex particles in solution. Polyelectrolyte titration showed that each latex sphere contained about 15 grafted PEI chains. The fastest aggregation was detected when about half of these chains were covered by a single NCC particle.     

Contactless conductivity detection of sodium monofluoroacetate in fruit juices on a CE microchip

Rapid and quantitative determination of sodium monofluoroacetate in diluted fruit juices (dilution 1:9 v/v in deionized water) and tap water was performed by microchip CE, using contactless conductivity detection. A separation buffer consisting of 20 mM citric acid and histidine at pH 3.5 enabled the detection of the monofluoroacetate (MFA) anion in diluted apple juice, cranberry juice, and orange juice without lengthy sample pretreatments. The analyte was very well separated from interfering anionic species present in juices and tap water. LODs in diluted juices and tap water were determined to be 125, 167, 138, and 173 microg/L for tap water, apple juice, cranberry juice, and orange juice, respectively, based upon an S/N of 3:1. Taking into account the dilution factor, the LODs for juice samples range from 1 to 2 mg/L, which is adequate for monitoring the toxicity of MFA in these juice beverages and tap water. The calibration curves for MFA in diluted fruit juices were linear over the range of 500 microg/L to 80 mg/L. The total analysis time for detecting the MFA anion in fruit juices was less than 5 min, which represents a considerable reduction in analysis time compared to other analytical methods currently used in food analysis.     

Flocculation and reflocculation of clay suspension by different polymer systems under turbulent conditions

The focused beam reflectance measurement (FBRM), also known as scanning laser microscopy (SLM), was used as a real-time monitor to study the flocculation and reflocculation of clay suspensions under different shear conditions in the presence of single polymer, dual polymer, microparticle and poly(ethylene oxide)/phenolformaldehyde (PEO/PFR) flocculation systems. For initial flocculation, the high molecular weight PEO and cationic polyacrylamide (CPAM) produced larger flocs than others. However, reflocculation of clay suspensions formed by these non- or low-charged polymers was insignificant after the initial flocs were broken under high shear force. In contrast, high charge density polymers, such as poly(diallyldimethylammonium chloride) (PDADMAC), do not form large initial flocs, but they showed significant reflocculation ability under a continuous shear condition. It is concluded that high flocculation can be obtained by effective polymer bridging, but high reflocculation can only be induced by high electrostatic attractive forces between suspended particles.     

Indirect determination of iodide by tungsten coil atomic emission spectrometry

The spectroscopic determination of iodide is a difficult challenge, especially in small sample volumes. The strongest transition lines for this element lie in the vacuum ultraviolet region of the spectrum, so most conventional instruments produce very weak signals. This work describes a tungsten coil atomic emission procedure for the indirect determination of iodide. A 25 μl aliquot of a solution containing a known amount of indium is deposited on the tungsten coil and dried with a simple heating program. Once the coil is dry, 25 μl of an iodide solution is added to the coil. The solution is dried and vaporized at high current. The atomic emission signal for In at 451.1 nm is monitored. In the presence of iodide, InI is formed and the In emission signal is attenuated. This attenuation is proportional to iodide concentration with a method detection limit of 0.6 mg l^{− 1} iodide using an In concentration of 10 mg l^{− 1}, and 3 mg l^{− 1} iodide using an In concentration of 50 mg l^{− 1}. Linear calibration curves span a range of two orders of magnitude. Analysis of a deionized water sample spiked with 50 mg l^{− 1} iodide gives a recovery of 100% and a precision of 5.5% relative standard deviation. Analysis of a tap water sample spiked with 50 mg l^{− 1} iodide gives a recovery of 140% and a precision of 7.1% relative standard deviation. The poor accuracy for the tap water analysis may arise from the reaction of In with other halides in the sample. This is the first report of determination of a halogen using the tungsten coil atomizer.