Optimization of experimental parameters in single-drop microextraction-gas chromatography-mass spectrometry for the determination of periodate by the Malaprade reaction, and its application to ethylene glycol

The aim of present work was to optimize the experimental parameters in single drop microextraction under solution immersion (SDME) and headspace (HS-SDME) extraction modes for the determination of periodate using guaifenesine [3-(2′-methoxyphenoxy)-1,2-propane diol] and norephedrine (phenylpropanolamine) as new and alternative reagents for the Malaprade reaction. The reactions were complete within 5 min resulting in the formation of 2-(2′-methoxyphenoxy)-acetaldehyde and benzaldehyde, respectively. SDME/HS-SDME of oxidation products with 2 μl of anisole or 1 μl of toluene, respectively, has permitted the determination of periodate at μg l⁻¹ concentration levels. The results indicated that HS-SDME (range 0.01-10 mg l⁻¹, r² = 0.9990; limit of detection 1.55 μg l⁻¹) was more sensitive than SDME (range 0.05-50 mg l⁻¹, r² = 0.9984; limit of detection 3.42 μg l⁻¹), and was inexpensive, rapid and convenient. Tolerance of excess of iodate has permitted the application of this method in the determination of ethylene glycol in motor oil; the average recovery on spiked sample was 98.6% with R.S.D. of 4.2%.     

Compound-specific stable carbon isotope ratios of phenols and nitrophenols derivatized with N,O-bis(trimethylsilyl)trifluoroacetamide

We developed an analytical method for measuring compound-specific stable carbon isotope ratios (δ¹³C) of phenols and nitrophenols in filter samples of particulate organic matter. The method was tested on 13 phenols derivatized with N,O-bis(trimethylsilyl)trifluoroacetamide (BSTFA), together with four nonphenolic compounds. The data obtained by our method required two specific corrections for the determination of valid δ¹³C values: (1) for nitro compounds, the routine correction with use of m/z 46 for the contribution of ¹²C¹⁷O¹⁶O molecules) to m/z 45 was modified due to impact of NO₂ on the m/z 46 trace, and (2) for the derivatized phenols, measured δ¹³C values were corrected for the shift in δ¹³C due to the addition of carbon atoms from the BSTFA moiety. Analysis of standard-spiked filters showed that overall there was a small compound-dependent bias in the δ¹³C values: the average bias ± the standard error of the mean of −0.21 ± 0.1‰ for the standard compounds tested, except 3-methylcatechol, methylhydroquinone, 4-methyl-2-nitrophenol, and 2,6-dimethyl-4-nitrophenol, whereas the average biases ± the standard errors of the mean for those were +1.2 ± 0.3‰, +1.2 ± 0.2‰, −1.2 ± 0.2‰, and −1.4 ± 0.5‰, respectively, when the injected mass of a derivatized compound exceeded 15 ngC. In situations where such small biases and uncertainties are acceptable, the method described here could be used to obtain valuable information about δ¹³C values. We also analyzed a real filter sample to demonstrate the practical applicability of the method.     

Characterization of Bioactive Compounds of Opuntia ficus-indica (L.) Mill. Seeds from Spanish Cultivars

Opuntia ficus-indica (L.) Mill. is the Cactaceae plant with the greatest economic relevance in the world. It can be used for medicinal purposes, animal nutrition, production of biofuels and phytoremediation of soils. Due to its high content of bioactive compounds, the prickly pear has antioxidant, antimicrobial and anticancer properties. The aim of this study was to determine the polyphenolic, fatty acid and amino acid profile and characterize the antioxidant capacity of seeds of seven Spanish prickly pear cultivars. A total of 21 metabolites, mainly phenolic acids and flavonols, were identified using ultraperformance liquid chromatography photodiode detector quadrupole/time-of-flight mass spectrometry (UPLC-PDA-Q/TOF-MS). Significant differences were found in the phenolic concentrations of the investigated varieties. The highest amount of phenolic compounds (266.67 mg/kg dry matter) were found in the “Nopal espinoso” variety, while the “Fresa” variety was characterized by the lowest content (34.07 mg/kg DM) of these compounds. In vitro antioxidant capacity was positively correlated with the amount of polyphenols. The amino acid composition of protein contained in prickly pear seeds was influenced by the variety. Glutamic acid was the predominant amino acid followed by arginine, aspartic acid and leucine, independent of prickly pear variety. Overall, 13 different fatty acids were identified and assessed in prickly pear seeds. The dominant fatty acid was linoleic acid, with content varying between 57.72% “Nopal ovalado” and 63.11% “Nopal espinoso”.     

Application of a quick,easy, cheap,effective, rugged and safe-based method for the simultaneous extraction of chlorophenols,alkylphenols, nitrophenols and cresols in agricultural soils,analyzed by using gas chromatography–triple quadrupole-mass spectrometry/mass spectrometry

Due to the different physico-chemical properties of phenols, the development of a methodology for the simultaneous extraction and determination of phenolic compounds belonging to several families, such as chlorophenols (CPs), alkylphenols (APs), nitrophenols (NTPs) and cresols is difficult. This study shows the development and validation of a method for the analysis of 13 phenolic compounds (including CPs, APs, NTPs and cresols) in agricultural soils. For this purpose, a quick, easy, cheap, effective, rugged and safe (QuEChERS)-based procedure was developed, validated and applied to the analysis of real samples. A derivatization step prior to the final determination by gas chromatography (GC) coupled to a triple quadrupole analyzer operating in tandem mass spectrometry (QqQ-MS/MS) was performed by using acetic acid anhydride (AAA) and pyridine (Py). The optimized procedure was validated, obtaining average extraction recoveries in the range 69–103% (10 μg kg⁻¹), 65–98% (50 μg kg⁻¹), 76–112% (100 μg kg⁻¹) and 76–112% (300 μg kg⁻¹), with precision values (expressed as relative standard deviation, RSD) ≤ 22% (except for 4-chlorophenol) involving intra-day and inter-day studies. Furthermore, 15 real soil samples were analyzed by the proposed method in order to assess its applicability. Some phenolic compounds (e.g. 2,4,6-trichlorophenol or 4-tert-octylphenol) were found in the samples at trace levels (<10 μg kg⁻¹).     

An oxacalix[2]arene[2]pyrimidine-bis(Zn-porphyrin) tweezer as a selective receptor towards fullerene C70

An oxacalix[2]arene[2]pyrimidine-bis(Zn^II-porphyrin) conjugate was readily prepared via nucleophilic aromatic substitution of a phenolic AB₃-Zn-porphyrin on the upper rim of a (1,3-alternate) 5,17-bis(methylsulfonyl)oxacalix[4]arene precursor. Efficient 1:1 complex formation between the ‘jaws’ bisporphyrin tweezer and fullerene C₇₀ was evidenced by ¹H NMR titrations (K = 3.0 × 10⁴ M⁻¹), while no detectable complexation could be observed with C₆₀. On the other hand, an analogous oxacalix[4]arene-bis(Cu-corrole) conjugate did not show any measurable (C₆₀ or C₇₀) fullerene binding.     

Uniform Ln (Eu, Tb) doped NaLa(WO4)2 nanocrystals: Synthesis, characterization, and optical properties

Uniform shuttle-like Ln³⁺ (Eu³⁺, Tb³⁺) doped NaLa(WO₄)₂ nanocrystals have been solvothermally synthesized, and the size of the nanocrystals could be easily controlled by adjusting the volume ratio of ethylene glycol (EG) to water. Doped with 5 mol% Eu³⁺ and Tb³⁺ ions, the NaLa(WO₄)₂ nanocrystals showed strong red and green emissions with lifetimes of 0.8 and 1.40 ms, respectively. A high quenching concentration of 15 mol% was observed in Eu³⁺-doped NaLa(WO₄)₂ nanocrystals and 35 mol% in Tb³⁺-doped NaLa(WO₄)₂ nanocrystals. The emission intensity measurements of Eu³⁺-doped NaLa(WO₄)₂ with different sizes indicated that the emission intensity of shuttles with length of 300 nm in average was stronger than that of shuttles with length of 900 nm in average, but was weaker than that of needles with length of 4 and 9 μm in average.     

Niobium(V) oxide coated on thin glass-ceramic rod as a solid phase microextraction fiber

The efficiency of niobium(V) oxide as a sorbent phase for solid phase microextraction (SPME) was investigated. The thin glass-ceramic rod was coated with niobium(V) oxide using chemical vapor deposition and Nb₂O₅ as a chemical precursor. Optimum conditions for the preparation and conditioning of the fibers are presented. The fibers were used for the extraction of a mixture of alcohols and a mixture of phenols from the headspace samples. The results obtained proved the suitability of niobium(V) oxide as a new SPME fiber. The calibration graphs for alcohols and phenols in a concentration range of 50-1000 μg l⁻¹ were linear (r > 0.995) and the detection limits were below 0.8 μg l⁻¹ level. The repeatability for one fiber (n = 6) under similar conditions was between 3 and 10.4%. The fiber-to-fiber reproducibility (n = 6) was between 5 and 15%.     

Triorganotin(IV) derivatives of umbelliferone (7-hydroxycoumarin) and their adducts with 1,10-phenanthroline: synthesis, structural and biological studies

New triorganotin(IV) derivatives of the general formula R₃Sn(Umb) (where, R = Me, n-Bu and Ph; Umb = umbelliferone anion) have been synthesized using sodium salt method. Further, the adducts of the general formula R₃Sn(Umb) · phen (where R = Me and Ph; phen = 1,10-phenanthroline) have also been synthesized by the interaction of the triorganotin(IV) derivatives of umbelliferone with 1,10-phenanthroline. The bonding and coordination behavior of these derivatives are discussed on the basis of IR, NMR (¹H, ¹³C and ¹¹⁹Sn), and ¹¹⁹Sn Mössbauer spectroscopic studies. These investigations indicate that umbelliferone acts as a monoanionic bidentate ligand in R₃Sn(Umb) coordinating through O(7) and O(1) in the solid-state. These polymeric R₃Sn(Umb) derivatives (where R = Me and n-Bu) have been proposed to have a trans-trigonal bipyramidal geometry with the three R groups in equatorial positions, while the axial positions are occupied by a phenolic oxygen and the O(1) atom from the adjacent molecule. A pseudotetrahedral geometry has been suggested for Ph₃Sn(Umb). A distorted octahedral geometry around tin has been proposed for R₃Sn(Umb) · phen, in which umbelliferone anion acts as a monodentate ligand coordinating through phenolic oxygen O(7). The newly synthesized derivatives have been assayed for their anti-inflammatory, cardiovascular and anti-microbial activities. The average LD₅₀ values >1000 mg kg⁻¹ of these derivatives indicate their safety margin. Among all the compounds tested, Ph₃Sn(Umb) · phen has been found to show potent anti-inflammatory activity with low mammalian toxicity and mild hypotensive activity.     

Solid-phase extraction combined with headspace single-drop microextraction of chlorophenols as their methyl ethers and analysis by high-performance liquid chromatography-diode array detection

Solid-phase extraction (SPE) of phenol and chlorophenols, their derivatization to methyl ethers, headspace single-drop microextraction (HS-SDME) of methyl ethers using 1-butanol as extraction solvent, and direct transfer of the drop into the injector for high performance liquid chromatography with diode array detection (HPLC-DAD) have been reported. A flanged-end polytetrafluoroethylene sleeve, 3 mm × 0.5 mm, placed at the tip of the syringe needle, allowed the use of 10 μL solvent drop for extraction. The procedure has been optimized for variables involved in SPE and HS-SDME. A rectilinear relationship was obtained between the amount of chlorophenols and peak area ratio of their methyl ethers/internal standard (4-methoxyacetophenone) in the range 0.01-10 mg L⁻¹, correlation coefficient in the range 0.9956-0.9996, and limit of detection in the range 1.5-3.9 μg L⁻¹ when HS-SDME alone was used for sample preparation. When using coupled SPE and HS-SDME, the linear range obtained was 0.1-500 μg L⁻¹, correlation coefficient in the range 0.9974-0.9998, and the limit of detection in the range 0.04-0.08 μg L⁻¹. Spiked real samples have been analyzed with adequate accuracy, and application of the method has been demonstrated for the analysis of chlorophenols formed upon bamboo pulp bleaching.     

Highly polyhapto-aromatic interactions in thallium(I) coordination

In the solid state, the Tl(I) complex of 4-hydroxybenzoate (HB⁻), [Tl(HB)]_n (1), can be regarded as containing polymeric chains linked through 2 × η⁶ interactions of the Tl atoms with phenyl groups from adjacent units. The thallium atoms contain close Tl^I ? π (aromatic) contacts, thus attaining a total hapticity of 16 with environments TlO₄C₁₂. The unusually high coordination number in the this compound may reflect the capacity of Tl(I) to act as both a Lewis acid and a Lewis base.     

Copper(II) complexes of N(4)-substituted thiosemicarbazones derived from pyridine-2-carbaldehyde: Crystal structure of a binuclear complex

Ten copper(II) complexes {[CuL¹Cl] (1), [CuL¹NO₃]₂ (2), [CuL¹N₃]₂ · 2/3H₂O (3), [CuL¹]₂(ClO₄)₂ · 2H₂O (4), [CuL²Cl]₂ (5), [CuL²N₃] (6), [Cu(HL²)SO₄]₂ · 4H₂O (7), [Cu(HL²)₂] (ClO₄)₂ · 1/2EtOH (8), [CuL³Cl]₂ (9), [CuL³NCS] · 1/2H₂O (10)} of three NNS donor thiosemicarbazone ligands {pyridine-2-carbaldehyde-N(4)-p-methoxyphenyl thiosemicarbazone [HL¹], pyridine-2-carbaldehyde-N(4)-2-phenethyl thiosemicarbazone [HL²] and pyridine-2-carbaldehyde N(4)-(methyl), N(4)-(phenyl) thiosemicarbazone [HL³]} were synthesized and physico-chemically characterized. The crystal structure of compound 9 has been determined by X-ray diffraction studies and is found that the dimer consists of two square pyramidal Cu(II) centers linked by two chlorine atoms.     

Dioxomolybdenum(VI) complexes containing N-heterocyclic carbenes

Compound MoO₂Cl₂(THF)₂ reacts with two equivalents of 1,3-dialkyl substituted 4,5-dimethylimidazol-2-ylidenes to give the dioxomolybdenum(VI) complexes MoO₂Cl₂(L^R)₂ [R = Me (1), i-Pr (2)]. Treatment of MoO₂Cl₂(THF)₂ with one equivalent of the N-heterocyclic carbenes L^Me, L^i-Pr and ^C1L^n-Bu (L^Me = 1,3,4,5-tetramethylimidazol-2-ylidene, L^i-Pr = 1,3-diisopropyl-4,5-dimethylimidazol-2-ylidene, and ^C1L^n-Bu = 1,3-dibutyl-4,5-dichloroimidazol-2-ylidene) affords the monocarbene adducts MoO₂Cl₂(L^R) [R = Me (3), i-Pr (4)] and MoO₂Cl₂(^C1L^n-Bu) (5), respectively. Decomposition of complexes 1-5 affords a molybdenum oxychloride anion [Mo₂O₅Cl₄]²⁻ as an imidazolium salt.     

Measurement of methyl mercury (I) and mercury (II) in fish tissues and sediments by HPLC-ICPMS and HPLC-HGAAS

A procedure for the extraction and determination of methyl mercury and mercury (II) in fish muscle tissues and sediment samples is presented. The procedure involves extraction with 5% (v/v) 2-mercaptoethanol, separation and determination of mercury species by HPLC-ICPMS using a Perkin-Elmer 3 μm C8 (33 mm × 3 mm) column and a mobile phase 3 containing 0.5% (v/v) 2-mercaptoethanol and 5% (v/v) CH₃OH (pH 5.5) at a flow rate 1.5 ml min⁻¹ and a temperature of 25 °C. Calibration curves for methyl mercury (I) and mercury (II) standards were linear in the range of 0-100 μg l⁻¹ (r² = 0.9990 and r² = 0.9995 respectively). The lowest measurable mercury was 0.4 μg l⁻¹ which corresponds to 0.01 μg g⁻¹ in fish tissues and sediments. Methyl mercury concentrations measured in biological certified reference materials, NRCC DORM - 2 Dogfish muscle (4.4 ± 0.8 μg g⁻¹), NRCC Dolt - 3 Dogfish liver (1.55 ± 0.09 μg g⁻¹), NIST RM 50 Albacore Tuna (0.89 ± 0.08 μg g⁻¹) and IRMM IMEP-20 Tuna fish (3.6 ± 0.6 μg g⁻¹) were in agreement with the certified value (4.47 ± 0.32 μg g⁻¹, 1.59 ± 0.12 μg g⁻¹, 0.87 ± 0.03 μg g⁻¹, 4.24 ± 0.27 μg g⁻¹ respectively). For the sediment reference material ERM CC 580, a methyl mercury concentration of 0.070 ± 0.002 μg g⁻¹ was measured which corresponds to an extraction efficiency of 92 ± 3% of certified values (0.076 ± 0.04 μg g⁻¹) but within the range of published values (0.040-0.084 μg g⁻¹; mean ± s.d.: 0.073 ± 0.05 μg g⁻¹, n = 40) for this material. The extraction procedure for the fish tissues was also compared against an enzymatic extraction using Protease type XIV that has been previously published and similar results were obtained. The use of HPLC-HGAAS with a Phenomenox 5 μm Luna C18 (250 mm × 4.6 mm) column and a mobile phase containing 0.06 mol l⁻¹ ammonium acetate (Merck Pty Limited, Australia) in 5% (v/v) methanol and 0.1% (w/v) l-cysteine at 25 °C was evaluated as a complementary alternative to HPLC-ICPMS for the measurement of mercury species in fish tissues. The lowest measurable mercury concentration was 2 μg l⁻¹ and this corresponds to 0.1 μg g⁻¹ in fish tissues. Analysis of enzymatic extracts analysed by HPLC-HGAAS and HPLC-ICPMS gave equivalent results.     

Infinite chains constructed from flexible bis(benzimidazole)-based ligands

Two neutral ligands, L¹ · 2H₂O and L² · H₂O, and seven complexes, [Cu(pmb)₂(L¹)] (1), [Cu(pmb)₂(L²)] (2), [Cu(Ac)₂(L²)] · 4H₂O (3), [Cu(4-aba)₂(L²)] (4), [Ag(4-ts)(L¹)(H₂O)] (5), [Ag₂(epes)₂(L¹)] · 2H₂O (6), [Ag(1,5-nds)_0.5(L²)] · 0.5C₂H₅OH · H₂O (7) [where L¹ = 1,1′-(1,4-butanediyl)bis(2-methylbenzimidazole); L² = 1,1′-(1,4-butanediyl)bis(2-ethylbenzimidazole), pmb = p-methoxybenzoate anion; Ac = acetate anion; 4-aba = 4-aminobenzoate anion; 4-ts = p-toluenesulfonate anion; epes = N-(2-hydroxyethyl)piperazine-N′-(2-ethanesulfonate) anion; 1,5-nds = 1,5-naphthalenedisulfonate anion], have been synthesized and characterized by elemental analysis, IR, and single-crystal X-ray diffraction. The L¹ and L² ligands in compounds 1–7 act as bridging ligands, linking metal ions into chain structures. The chains in compounds 3, 4 and 6 interlace with each other by hydrogen bonds to generate 3D supramolecular structures. In compound 5, π–π interactions between adjacent L¹ ligands hold the chains to a supramolecular layer. In compound 7, the sulfonate anions act as counterions in the framework. The thermal stabilities of 3, 6 and 7, and the luminescent properties for 5–7 in the solid states are also discussed.     

Dependence of calibration sensitivity of a polysulfone/Ru(II)-tris(4,7-diphenyl-1,10-phenanthroline)-based oxygen optical sensor on its structural parameters

The optimum performance of an optical oxygen sensor based on polysulfone (PSF)/[Ru(II)-Tris(4,7-diphenyl-1,10-phenanthroline)] octylsulfonate (Ru(dpp)OS) was checked by carefully tuning the parameters affecting the membrane preparation. In particular, membranes having thickness ranging between 0.2 and 8.0 μm with various luminophore concentrations were prepared by dip-coating and tested. The membrane thickness was controlled by tuning the solution viscosity, and was measured both by secondary ion mass spectrometry (SIMS) and by visible spectroscopy (Vis). Luminescence-quenching-based calibration was a single value of the Stern-Volmer constant (K^′SV) for membranes containing up to 20 mmol Ru(dpp) g⁻¹ PSF (1.35 μm average thickness). The K^′SV value decreased for larger concentration. The highest sensitivity was obtained with membrane thickness around 1.6 μm, having a response time close to 1 s. Thicker membranes exhibited an emission saturation effect and were characterized by longer response time. The K^′SV behavior was interpreted on the basis of a mathematical approach accounting for the contribution of luminescence lifetime (τ₀), oxygen diffusion coefficient (DO₂) and oxygen solubility inside the membrane (sO₂) establishing the role of all of them and allowing their experimental determination. Moreover, a simple experimental way to estimate K^′SV without needing calibration was proposed. It was based either on the light emission asymmetry or on the percent variation of light emission on passing from pure nitrogen to pure oxygen.     

Dinuclear copper(II) perchlorate complexes with 6-(benzylamino)purine derivatives: Synthesis,X-ray structure,magnetism and antiradical activity

The reactions of Cu(ClO₄)₂·6H₂O with 6-(benzylamino)purine derivatives in a stoichiometric 1:2 metal-to-ligand ratio led to the formation of penta-coordinated dinuclear complexes of the formula [Cu₂(μ-L^1–8)₄(ClO₄)₂](ClO₄)₂·nsolv, where L¹ = 6-(2-fluorobenzylamino)purine (complex 1), L² = 6-(3-fluorobenzylamino)purine (2), L³ = 6-(4-fluorobenzylamino)purine (3), L⁴ = 6-(2-chlorobenzylamino)purine (4), L⁵ = 6-(3-chlorobenzylamino)purine (5), L⁶ = 6-(4-chlorobenzylamino)purine (6), L⁷ = 6-(3-methoxybenzylamino)purine (7) and L⁸ = 6-(4-methoxybenzylamino)purine (8); n = 0–4 and solv = H₂O, EtOH or MeOH. All the complexes have been fully characterized by elemental analysis, FTIR, UV–Vis and EPR spectroscopy, and by magnetic and conductivity measurements. Variable temperature (80–300 K) magnetic susceptibility data of 1–8 showed the presence of a strong antiferromagnetic exchange interaction between two Cu(II) (S = 1/2) atoms with J ranging from −150.0(1) to −160.3(2) cm⁻¹. The compound 6·4EtOH·H₂O was structurally characterized by single crystal X-ray analysis. The Cu?Cu separation has been found to be 2.9092(8) Å. The antiradical activity of the prepared compounds was tested by in vitro SOD-mimic assay with IC₅₀ in the range 8.67–41.45 μM. The results of an in vivo antidiabetic activity assay were inconclusive and the glycaemia in pre-treated animals did not differ significantly from the positive control.     

Bis(pyrazole)- and bis(pyrazolyl)-palladium complexes as phenylacetylene polymerization catalysts

Two types of pyrazole-based palladium complexes were used to catalyze the polymerization of phenylacetylene. Catalysts with electron-withdrawing linkers, [{1,3-(3,5-R₂pzCO)₂C₆H₄}Pd₂Cl₂(μ-Cl)₂] (R = ^tBu (1), Ph (2), Me (3), [{2,6-(3,5-R₂pzCO)₂C₅H₃N)}PdCl₂] (R = ^tBu (4), Me (5)), show high conversion; whilst those with simple pyrazole ligands, [(3,5-R₂pz)₂PdCl₂] (R = H (6), Me (7), ^tBu (8)), [(3,5-^tBu₂pz)₂PdCl(Me)] (9), have much lower conversions. Conversion greatly improved when 9 was used to catalyze the co-polymerization of sulfur dioxide and phenylacetylene. Both types of catalysts produce predominantly trans–cisoidal polyphenylacetylene.     

A novel multiwalled carbon nanotubes bonded fused-silica fiber for solid phase microextraction-gas chromatographic analysis of phenols in water samples

The present work reports on the synthesis of chemically bonded multiwalled carbon nanotubes (MWCNTs)/fused-silica fibers and their use in solid phase microextraction of seven phenols from water samples coupled with gas chromatography (GC). The synthetic strategy was verified by infrared (IR) spectroscopy and field emission scanning electron microscopy. Adsorption factors (pH, ionic strength, stirring rate, adsorption time and temperature) and desorption factors (time and temperature) of the fibers were systematically investigated. Detection limits to seven phenols were less than 0.05 μg L⁻¹, and their calibration curves were all linear (R² ≥ 0.9984) in the range from 0.05 to 5000 μg L⁻¹. This method was then utilized to analyze two real water samples from Yellow River and sanitary wastewater, resulting in satisfactory results. Compared with normal solid phase materials, this MWCNTs-bonded fused-silica fibers showed a number of advantages: wide linear range and low detection limit for extracting phenols couple with GC, and good stability in acid, alkali, organic solvents and at high temperature.     

Novel hydridotris(pyrazolyl)borate ruthenium(II) complexes containing the water-soluble phosphane 1,3,5-triaza-7-phosphaadamantane: Synthesis and evaluation of DNA binding properties

A series of half-sandwich ruthenium(II) complexes containing κ³(N,N,N)-hydridotris(pyrazolyl)borate (κ³(N,N,N)-Tp) and the water-soluble phosphane 1,3,5-triaza-7-phosphaadamantane (PTA) [RuX{κ³(N,N,N)-Tp}(PPh₃)_2−n(PTA)_n] (n = 2, X = Cl (1), n = 1, X = Cl (2), I (3), NCS (4), H (5)) and [Ru{κ³(N,N,N)-Tp}(PPh₃)(PTA)L][PF₆] (L = NCMe (6), PTA (7)) have been synthesized. Complexes containing 1-methyl-3,5-diaza-1-azonia-7-phosphaadamantane(m-PTA) triflate [RuCl{κ³(N,N,N)-Tp}(m-PTA)₂][CF₃SO₃]₂ (8) and [RuX{κ³(N,N,N)-Tp}(PPh₃)(m-PTA)][CF₃SO₃] (X = Cl (9), H (10)) have been obtained by treatment, respectively, of complexes 1, 2 and 5 with methyl triflate. Single crystal X-ray diffraction analysis for complexes 1, 2 and 4 have been carried out. DNA binding properties by using a mobility shift assay and antimicrobial activity of selected complexes have been evaluated.     

Synthesis, characterization, antibacterial and cytotoxic activity of new palladium(II) complexes with dithiocarbamate ligands: X-ray structure of bis(dibenzyl-1-S:S′-dithiocarbamato)Pd(II)

Six palladium(II) dithiocarbamates of general formula Pd(AmDTC)₂, where HAmDTC = aminedithiocarbamic acid, [Pd(II) piperidinedithiocarbamate (1), Pd(II) 4-methylpiperidinedithiocarbamate (2), Pd(II) N-methylbenzyldithiocarbamate (3), Pd(II) dibenzyldithiocarbamate (4), Pd(II) dicyclohexyldithiocarbamate (5), Pd(II) N-cyclohexyl-N-methyldithiocarbamate (6)] have been synthesized and characterized by elemental analyses, FT-IR, ¹H and ¹³C NMR. The X-ray structure of Pd(II), compounds 3 and 4, showed that the ligands are chelated by both sulfur atoms with bond angles S1-Pd-S4 = 179.24(2)° and S2-Pd-S3 = 179.09(5)°, with a distorted square planar geometry around Pd. All these complexes were screened for cytotoxic and antibacterial effects and showed significant antibacterial activity and no substantial in vitro cytotoxicity indicating specificity of the compounds.