Investigation of visible light active Ag sensitized mixed phase TiO2 photocatalyst for solar energy application

Visible photo-active anatase and mixed phase Ag/TiO₂ photocatalysts were prepared using sol–gel method with 1.5 wt% Ag concentration. Due to the large band gap, pristine titania (anatase) is mainly active in the UV light and the photoactivity is limited. But in the presence of both anatase (~3.2 eV) and rutile (~3.0 eV) phases in TiO₂, the catalyst is expected to show enhancement in the photoactivity due to mixed phase junction. The Ag particles are used to act as electron sink and to swiftly transport the photo-generated electrons and, consequently, lessen the recombination rate. The synergistic effect of surface plasmon resonance (SPR) enhanced local field due to Ag particles and the existing mixed phase of TiO₂ is expected to provide a boost in its photoactivity in the visible region. In the present work the mixed phase Ag/TiO₂ photocatalyst showed large enhancement in the degradation of methylene blue compared to all the reference systems.     

Synthesis of nanosized TiO2/SiO2 particles using microwave processes and their photocatalytic activity on the decomposition of orange II

The nanosized titania and TiO₂/SiO₂ particles were prepared by the microwave-hydrothermal method. The effect of physical properties TTIP/TEOS ratio and calcination temperature has been investigated. The major phase of the pure TiO₂ particle is of the anatase structure, and a rutile peak was observed above 800°C. In TiO₂/SiO₂ particles, however, no significant rutile phase was observed, although the calcination temperature was 900°C. No peaks for the silica crystal phase were observed at either silica/titania ratio. The crystallite size of TiO₂/SiO₂ particles decreases as compared to pure TiO₂ at high calcination temperatures. The TiO₂/SiO₂ particles show higher activity on the photocatalytic decomposition of orange II as compared to pure TiO₂ particles.     

Study of the role of metal core on the thermal behavior of Ag@TiO2 core–shell nanoparticles

Thermal behavior of the TiO₂ shell in the core–shell Ag@TiO₂ system has been investigated by the time differential perturbed angular correlation (TDPAC), transmission electron microscope and X-ray diffraction measurements in the temperature range from 473 to 1073 K. Although the thickness of the TiO₂ shell increases on annealing, the TDPAC results show that the anatase phase persists till 1073 K. This is in contrast with the results for the pure TiO₂ nanoparticles. These observations suggest that the phase transformation from anatase to rutile is hindered in case of core–shell nanoparticles possibly because the growth of the shell thickness in case of Ag@TiO₂ nanoparticles is not effective for rutile formation due to the presence of Ag-core.     

Thermal and hydrothermal stability of flame hydrolytically synthesized SiO2/TiO2 mixed oxides

The phase stability of the two TiO₂ modifications (anatase and rutile) in fumed SiO₂/TiO₂ nano-composites (0–24.8 wt-% silica) under thermal and hydrothermal conditions was investigated by X-ray powder diffraction, transmission electron microscopy (TEM) and gas adsorption methods (BET). The results show that the phase transformation from anatase to rutile type of structure and the growth of anatase crystallites are significantly retarded by mixing small amounts of SiO₂ into TiO₂, while the specific surface area is maintained. The SiO₂/TiO₂-composites reveal a remarkable shift in the anatase to rutile transformation temperature from approx. 500 °C (pure TiO₂) to approx. 1000 °C (samples with SiO₂ contents of more than 10%). The rate of phase transformation from anatase to rutile is enhanced under hydrothermal conditions compared to conventional thermal treatment, e.g. pure titania (AEROXIDE^® TiO₂ P25) annealed under hydrothermal conditions (100 g/m³ absolute humidity, 4 h at 600 °C) had a rutile content of 85%, while the same specimens annealed in absence of humidity contained only 46% rutile. However, the difference in rate of phase transformation became less pronounced when the silica content in SiO₂/TiO₂-composites was further increased.TEM results showed that the surface of the anatase crystallites was covered with silica. This averts coalescence of anatase crystallites and keeps them under a critical size during the annealing process. When the crystal domains grew larger, a rapid conversion to rutile took place. The critical size of anatase crystallites for the phase transformation was estimated to be 15–20 nm.     

Remarkable Charge Separation and Photocatalytic Efficiency Enhancement through Interconnection of TiO2 Nanoparticles by Hydrothermal Treatment

Although tremendous effort has been directed to synthesizing advanced TiO₂, it remains difficult to obtain TiO₂ exhibiting a photocatalytic efficiency higher than that of P25, a benchmark photocatalyst. P25 is composed of anatase, rutile, and amorphous TiO₂ particles, and photoexcited electron transfer and subsequent charge separation at the anatase–rutile particle interfaces explain its high photocatalytic efficiency. Herein, we report on a facile and rational hydrothermal treatment of P25 to selectively convert the amorphous component into crystalline TiO₂, which is deposited between the original anatase and rutile particles to increase the particle interfaces and thus enhance charge separation. This process produces a new TiO₂ exhibiting a considerably enhanced photocatalytic efficiency. This method of synthesizing this TiO₂, inspired by a recently burgeoning zeolite design, promises to make TiO₂ applications more feasible and effective.     

Preparation of nanocrystalline anatase TiO2 using basic sol-gel method

Nanocrystalline titanium dioxide particles with anatase structure and high thermal stability have been synthesized using the basic sol-gel method. The particle size and morphology were refined under hydrothermal conditions in the presence of different concentrations of tetramethylammonium hydroxide (TMAH) at 210°C and 230°C. XRD and TEM analysis showed that the TiO₂ particles obtained were homogeneous and monodispersive at low contents of TMAH. All intense peaks, clearly observed in the XRD patterns, were assigned to the anatase phase and no rutile phase was observed. At high contents of TMAH, nanoscale small (10–30 nm) and larger (>100 nm) TiO₂ particles were one-pot synthesized. The nanocrystalline TiO₂ particles synthesized by this method have good thermal stability. With the sintering temperature of up to 650°C, all the XRD peaks maintained good agreement with the anatase reference data.     

Double-Layer TiO2 Electrodes with Controlled Phase Composition and Morphology for Efficient Light Management in Dye-Sensitized Solar Cells

The light-scattering effect in the dye-sensitized solar cells (DSCs) was studied by controlling TiO₂ phase composition and morphology by fabrication of double-layer cells with different arrangement modes. The starting material for preparation of TiO₂ cells was synthesized by an aqueous sol–gel process. X-ray diffraction and field emission scanning electron microscopic analyses revealed that TiO₂ nanoparticles had particle size ranging between 18 and 44 nm. The optical property and band gap energy of TiO₂ nanoparticles were studied through UV–Vis absorption. The indirect optical band gap energy of anatase and rutile nanoparticles was found to be 3.47 and 3.41 eV, respectively. The double-layer DSC made of nanostructured TiO₂ film with phase composition of 78 % anatase and 22 % rutile as the under-layer and mixtures of anatase-nanoparticles and anatase-microparticles as the over-layer (i.e., NM solar cell) was shown the highest power conversion efficiency (PCE) of 6.04 % and open circuit voltage of 795 mV. This was achieved due to the optimal balance between the light scattering effect and dye sensitization parameters. Optimum light scattering of photoanode led to improve the PCE of NM double-layer solar cell which was demonstrated by diffuse reflectance spectroscopy.     

The influence of concentration of doping elements on anatase–rutile transformation at the synthesis of rutile pigments (Ti,Cr,Nb)O2 and their pigmentary properties

An analysis of the effects of dopants concentration and different starting titanium compounds on the anatase to rutile phase transformation at the synthesis of rutile pigments Ti_1?3xCr_xNb_2xO_2±δ is presented in this study. The main goal was to analyze reaction mixtures for x = 0.05 (previous study) and 0.30 by simultaneous TG–DTA analysis and to determine the temperature of anatase–rutile transition. For x = 0.05, initial temperatures 760–830 °C are needful for a formation of rutile structure. The temperature is the lowest for the hydrated Na₂Ti₄O₉ paste (760 °C) and similar for other starting compounds of titanium. But for x = 0.30, the anatase–rutile transition begins at higher temperatures 910–1,030 °C because of high-Nb content, which is the inhibitor of this modification change. In addition, we found the influence of calcination temperatures (850, 900, 950, 1000, 1050, 1100, and 1150 °C) on color properties and particle size distribution of these materials prepared from anatase TiO₂ and with x = 0.30. Selected pigments were also analyzed by X-ray powder diffraction.     

High temperature stability and photocatalytic activity of nanocrystalline anatase powders with Zr and Si co-dopants

TiO₂ nanopowders doped by Si and Zr were prepared by sol–gel method. The effects of Si and Zr doping on the structural, optical, and photo-catalytic properties of titania nanopowders have been studied by X-ray diffraction (XRD), scanning electron microscopy, transmission electron microscopy, and UV–Vis absorption spectroscopy. XRD results suggest that adding impurities has a significant effect on anatase phase stability, crystallinity, and particle size of TiO₂. Titania rutile phase formation in ternary system (Ti–Si–Zr) was inhibited by Zr⁴⁺ and Si⁴⁺ co-doped TiO₂ in high temperatures (500–900 °C) and 36 mol% anatase composition is retained even after calcination at 1,000 °C. The photocatalyst activity was evaluated by photocatalytic degradation kinetics of aqueous methylen orange under visible radiation. The results show that the photocatalytic activity of the 20 %Si and 15 %Zr co-doped TiO₂ nanopowders have a larger degradation efficiency than pure TiO₂ under visible light.     

N-doped TiO<Subscript>2</Subscript> applied in low-temperature-based dye-sensitized solar cells

With urea as nitrogen source, N-doped TiO₂ powders were synthesized and fabricated for low-temperature dye-sensitized solar cells (DSSCs) by the method of doctor-blade, and the highest temperature of the whole process was 120 °C. SEM, TEM, XRD, DRS, and XPS were used to analyze the microstructure of the N-doped TiO₂ powders. EIS, Bode plot, UV–Vis and I–V were employed to measure the photovoltaic performance of the DSSCs. The maximum photoelectric conversion efficiency (η) was 5.18 % when the amount of the doped nitrogen was 4 %, and, when compared with the η of 4.22 % for pure TiO₂, the short circuit current was increased by 22.2 % and the efficiency was increased by 22.7 %. It has been shown that the doped nitrogen could effectively suppress TiO₂ crystal phase transition from anatase to rutile, and decrease the size of particles. Therefore, the increased photoelectric conversion efficiency of the N-doped TiO₂-based DSSC was ascribed to the more suitable crystal phase, sizes and inner structure.     

The influence of titanium dioxide phase composition on dyes photocatalysis

A comparative study of TiO₂ powders prepared by sol–gel methods is presented. Titanium tetraisopropoxide was used as the precursor for the sol–gel processes. The effects of the annealing treatment on phase, crystallite size, porosity and photodegradation of dyes (methyl orange and methylene blue) were studied. The phase structure, microstructure and surface properties of the films were characterized by using X-ray diffraction (XRD) and Atomic Force Microscopy (AFM). The X-ray diffraction was used for crystal phase identification, for the accurate estimation of the anatase–rutile ratio and for the crystallite size evaluation of each polymorph in the samples. It was found that the only TiO₂ anatase phase of the synthesized TiO₂ develops below 500 °C, between 600 and 800 °C the anatase coexist with rutile and above 800 °C only the rutile phase was found in the samples. Attention has been paid not only to crystal structures, but also to the porosity, the particle size and the photocatalytic properties. However, the annealing temperature was found to have significant influence on the photocatalytic properties. Different TiO₂ doctor blade thin films were obtained mixing the sol gel powder (100% anatase) and TiO₂ Aldrich with TiO₂ Degussa P25. The surfactant (Triton X100 or sodium dodecyl sulfate) affects the packing density of the particles during deposition and the photocatalytic degradation efficiency of the dyes. The photocatalytic degradation kinetics of methyl orange and methylene blue using TiO₂ thin film were investigated.     

The effect of different atmospheres on structural changes of titanate nanotubes during heating

Thermal stability of titanate nanotubes (Ti-NT) was studied in temperature range from room temperature up to 1000 °C in three different atmospheres—in air, vacuum and helium—and differences were observed. In air, vacuum and helium, the release of adsorbed and crystal water was detected in temperatures up to 200 °C. Transformation of the initial structure to anatase form of TiO₂ was found independently of the atmosphere used. But in air the transformation to anatase occurred at lower temperature. The difference between these atmospheres was approximately 100 °C. However, only in air, the transformation to sodium hexatitanate and rutile form of TiO₂ occurred at higher temperatures. In vacuum, only the anatase phase was detected up to 800 °C. In helium, the transformation to rutile was observed but not to sodium hexatitanate. The changes of the initial structure of Ti-NT during the elevation of temperature were studied by combination of in situ powder X-ray diffraction, differential scanning calorimetry, thermal gravimetric analysis and mass spectroscopy.     

Effect of silicon dioxide on the formation of the phase composition and pore structure of titanium dioxide with the anatase structure

The formation of the structure of titanium dioxide modified with silicon dioxide, which was introduced as tetraethyl orthosilicate, was studied. It was found that the formation of the nanocrystalline structure of TiO₂ occurred upon the modification of titanium dioxide with silicon dioxide. This nanocrystalline structure of TiO₂ was formed by highly dispersed anatase particles of size 6–10 nm stabilized by silicon oxide layers, which were formed upon the decomposition of tetraethyl orthosilicate. An increase in the modifier concentration resulted in a deceleration of the growth of anatase particles and an increase in the temperature of the phase transition of anatase to rutile. It was found that the anatase phase in the samples containing 5–15 wt % SiO₂ was stable up to 1000°C. The stabilization of highly dispersed anatase particles facilitated the retention of the developed fine-pore structure of xerogels with a pore diameter of 4 nm up to 900°C.     

TiO2-assisted photocatalytic degradation of diclofenac, metoprolol, estrone and chloramphenicol as endocrine disruptors in water

The photocatalytic oxidation of diclofenac, metoprolol, estrone and chloramphenicol was tested in the tube reactor using different commercially available TiO₂. The photocatalysts were characterized using BET, XRD and SEM. The studied photocatalysts differed in S_BET, pore volume and rutile presence. It was observed that generally anatase TiO₂ possessed the highest activity in the photocatalytic oxidation of diclofenac, chloramphenicol and estrone. The presence of rutile enhanced the photooxidation of metoprolol. In case of the other pollutants, however, rutile diminished the photooxidation efficiency. The most effective in the reduction of the COD parameter of treated water was anatase with 21 nm crystals. The photooxidation of all studied pollutants can be described by the pseudo-first order kinetics with the values ranging from 0.46 × 10^?2 min^?1 in case of estrone removal over Tytanpol (Z.A. Police, Poland) to 1.87 × 10^?2 min^?1 for the removal of chloramphenicol over TiO₂ 21 nm (Sigma-Aldrich). The highest initial reaction rates were obtained for metoprolol removal over TiO₂ 21 nm (Sigma-Aldrich) 1.9 × 10^?6 mol dm³ min^?1 being three times higher than that determined for estrone photocatalytic oxidation over TiO₂ (Sigma-Aldrich).     

Synthesis of Mixed-Phase TiO<Subscript>2</Subscript> Nanopowders Using Atmospheric Pressure Plasma Jet Driven by Dual-Frequency Power Sources

Mixed-phase TiO₂ nanopowders with different ratios of anatase and rutile have been successfully synthesized using atmospheric pressure plasma jet driven by dual-frequency power sources. The crystal structures of the TiO₂ nanopowders were characterized by X-ray diffraction, SAED, HRTEM, and Raman shift spectroscopy. These results indicated that samples possessed anatase and rutile structure, in addition, the crystallinity of the TiO₂ nanopowders increased and the chlorine contamination decreased with discharge RF power increasing. The photocatalytic activity of the TiO₂ nanopowders was evaluated by decomposition methylene blue solution. The TiO₂ nanopowders which were produced at the discharge RF power of 110 W had the highest photocatalytic activity. Optical emission spectroscopy (OES) was used to detect various excited species in the plasma jet. The results indicate that the various RF power significantly changes the intensities of emission lines (Ar, Ar⁺, Ti, Ti⁺, Ti²⁺, Ti³⁺ and O), which results in the TiO₂ nanopowders a mixture of anatase and rutile phases. The nonequilibrium chemical composition could be formed in one step without anneal. It may have potential applications for synthesizing nanosized particles of high crystallinity by reactive nonthermal plasma processing.     

Transition from anatase to rutile phase in titanium dioxide (TiO2) nanoparticles synthesized by complexing sol–gel process: effect of kind of complexing agent and calcinating temperature

In this work, the structural and optical properties of titanium dioxide (TiO₂) nanopowders are studied. The TiO₂ nanoparticles were synthesized by complexing sol–gel process and effect of complexing agents on transition of the anatase phase to rutile phase during the heat treatment have been investigated. In addition, we have studied the grain size of TiO₂ powders and their dependence on the type of complexing agent. The analysis of the XRD patterns, FT-IR and UV–Vis spectroscopy, BET surface area and TEM images show that the synthesis of nanoparticles with acetyl acetone (AcAc) as complexing agent yielded the smallest size of nanoparticles about 22–35 nm. Our results indicate that with increasing the calcinating temperature, the size of the nanoparticles is increased and the energy gap reduced, too. Also, the optical band gap was obtained in the range of 3.4–4.1 and 3.06–3.74 eV for anatase and rutile phases, respectively.     

Polyacrylamide gel synthesis and photocatalytic properties of TiO2 nanoparticles

In this study, a polyacrylamide gel route was introduced to synthesize TiO₂ nanoparticles. The influence of synthesis conditions on the properties of products was investigated. It is found that the samples prepared at the calcination temperature of 400 °C crystallize majorly in the anatase phase with a minor rutile phase. The second rutile phase has a dependence on the chelating agent, which is formed more readily when using acetic acid as the chelating agent. The introduction of acrylamide and glucose to the precursor solution shows the capability of improving the particle morphology, and the resulted particles are uniformly shaped like spheres. The photocatalytic activity of the prepared TiO₂ samples was evaluated by the degradation of acid orange 7 under 254 nm ultraviolet irradiation, revealing that they exhibit a good photocatalytic activity. Ethanol was used as a ^·OH scavenger to investigate its effect on the photocatalytic efficiency as well as the ^·OH radical yields. Based on the experimental results, ^·OH radical is suggested to be the dominant active species responsible for the dye degradation.     

Preparation and Characterization of Peroxo Titanic Acid Solution Using TiCl3

The peroxo titanic acid solution was successfully prepared using titanium trichloride as a precursor. The basic properties of the TiO₂ film prepared by the solution were investigated in view of phase change, bandgap energy, crystalline size etc. The film displayed amorphous TiO₂ at room temperature, anatase above 281°C and a mixture of anatase and rutile at 990°C. The crystalline size increases with annealing temperatures, while the bandgap energies decrease due to the quantum size effect and the formation of rutile phase which has low bandgap energy. As a result of TG-DTA, it was found that annealing treatment at 990°C for 2 h formed a mixture of anatase and rutile through three steps: (1) the removal of physically adsorbed water (2) the decomposition of peroxo group (3) amorphous-anatase or anatase-rutile phase transformation.     

Anatase–rutile transformation at the synthesis of rutile pigments (Ti,Cr,Nb)O2 and their color properties

Synthesis of rutile pigments is based on solid state reaction and on Hedvall effect, i.e., phase transformation from anatase to rutile. Therefore, it is important to know the thermal behavior of these compounds (the temperature of this change). The goal was to prepare rutile pigments of type Ti_1?3xCr_xNb_2xO_2+x/2 by conventional solid state method from titanium dioxide TiO₂ (AV-01, anatase), to determine an influence of composition (x = 0, 0.05, 0.10, 0.20, 0.30, 0.50) and calcination temperature (850; 900; 950; 1,000; 1,050; 1,100; 1,150 °C) on color properties of these compounds and to analyze other starting compounds of titanium (hydrated anatase paste TiO₂·nH₂O, titanyl sulfate dihydrate TiOSO₄·2H₂O (VKR 611), hydrated sodium titanium oxide paste Na₂Ti₄O₉·nH₂O) and their reaction mixtures for x = 0.05 by simultaneous TG–DTA analysis. According to the highest chroma C of color, the optimal conditions for synthesis of these pigments are concentration x = 0.05 and calcination temperature 1,050 °C and higher. It was observed that initial temperature 760–830 °C is needful for a formation of rutile structure. This temperature is the lowest for hydrated Na₂Ti₄O₉ paste (760 °C) and similar for other starting compounds of titanium.     

Structural characterization of Fe/Ti oxide photocatalysts by X-ray,ESR, and Mössbauer methods

The polycrystalline solids TiO₂Fe₂O₃, with iron contents in the range 0–10 at.%, prepared by coprecipitation and by impregnation, and treated in air at temperatures in the range 500–1000°C, have been studied by X-ray, ESR, and Mössbauer methods. The TiO₂ in the samples treated at 800 and 1000°C always forms the rutile phase and the Fe³⁺ has a rather low solubility in it (～0.1 at.%). The Fe³⁺ in excess forms the antiferromagnetic pseudobrookite phase (Fe₂TiO₅). The samples treated at 500 and 650°C show a dependence on the preparation method. Those prepared by coprecipitation give at 500°C the pure anatase phase in which the Fe³⁺ has a higher solubility (≥ 1%); those prepared by impregnation give the anatase phase accompanied by a variable amount of rutile. The treatment at 650°C provokes the partial transformation of anatase to rutile and the complete development of the Fe₂TiO₅ phase. The relevance of these results to the photocatalytic properties shown by these solids for the photoreduction of dinitrogen to ammonia is discussed.