Liquid—liquid equilibria for ternary systems of water—phenol and solvents: new UNIFAC parameters for interactions between the groups ACOH/COOH and prediction

The UNIFAC group-contribution method is used to predict ternary liquid—liquid equilibrium data presented in a recent paper (Alvarez Gonzalez et al.) for the systems water/phenol/benzene, water/phenol/ethylbenzene, water/phenol/nonanoic acid, water/phenol/ethyl acetate, water/phenol/isopropyl acetate, water/phenol/n-butyl acetate, water/phenol/isoamyl acetate and water/phenol/cyclohexyl acetate at 25°C and water/phenol/n-hexyl acetate at 25, 35 and 45°C. New UNIFAC interaction parameters between the groups ACOH/COOH have been obtained.A comparison between the experimental and predicted values is presented.     

Thermodynamics of association for benzene-benzyl alcohol,benzene-phenethyl alcohol,and fluorobenzene-benzyl alcohol in dilute aqueous solution

Vapor pressure measurements have been made on dilute aqueous solutions of benzene-benzyl alcohol (BZOH), benzene-phenethyl alcohol (PEOH), and fluorobenzene-BZOH at 15, 25, 35, and 45°C. The benzene results have been interpreted with a mass action model which attributes deviations from ideality to the formation of benzene dimers and heterodimers with BZOH and PEOH. The benzene heterodimers form endothermically at 25°C with large and negative heat capacity changes. The dimerization constant for the benzene-BZOH dimer reaches a maximum of 0.57 M^–1 at about 37°C, while the benzene-PEOH dimer reaches a maximum of 0.60 M^–1 around 30°C. The fluorobenzene results have been interpreted with a mass action model which, in addition to fluorobenzene dimers and heterodimers, includes the formation of a fluorobenzene-BZOH trimer. Thermodynamic properties for these aggregates are reported and compared with results obtained in previous studies.     

ADSORPTION OF SURFACE-ACTIVE AGENTS FROM AQUEOUS SOLUTION: HYDROPHOBIC SUBSTRATES∗

Isotherms for the adsorption of sodium dodecyl benzene sulfonate, sodium POE (4) nonyl phenol sulfate, and POE (25) nonyl phenol, on the hydrophobic crystalline herbicides atrazine and cyanazine were determined. Anionic surfactants were measured at 5°, 25°, and 50° C; the nonionic surfactant at 25° C only. Low degrees of surface coverage were observed; in only one case (atra-zine/NaDBS) was monolayer coverage approached. On the other hand, adsorption was accompanied by a significant increase in negative zeta potential. Although DLVO calculations suggest that this adsorption should lead to stable aggregates, these are of such size that gravitational effects overpower the DLVO terms.     

Craquage thermique de l'aniline 1-14C

Thermal cracking of aniline 1-¹⁴C at atmospheric pressure at 900°C and a contact time of 2.5 sec breakdown mechanisms of the formation of benzene with an elimination of nitrogen, and formation of heterocyclic compounds and condensation products has been studied. Most of the degradation compounds are produced by a mechanism similar to the primary mechanism for the degradation of phenol: elimination of HCN with formation of inactive C₅H₆. The formation of nitriles is not negligible.     

Ultrasonic and IR study of molecular association process through hydrogen bonding in ternary liquid mixtures

Complex formation in ternary liquid mixtures of heterocyclic compounds, viz. pyridine and quinoline with phenol in benzene has been studied through ultrasonic velocity measurements (at 2 MHz) in the concentration range of 0.010–0.090 at varying temperatures of 35, 45 and 55 °C. The ultrasonic velocity and density data are used to estimate adiabatic compressibility, intermolecular free length, molar sound velocity, molar compressibility and specific acoustic impedance. These acoustical parameters, in turn, are used to study the solute–solute interactions in these systems. The ultrasonic velocity shows a maxima and adiabatic compressibility a corresponding minima as a function of concentration for these mixtures. The results indicate the possible occurrence of complex formation between unlike molecules through intermolecular hydrogen bonding between the nitrogen atom of pyridine and quinoline molecules and the hydrogen atom of phenol molecule. Further, the excess values of adiabatic compressibility and intermolecular free length have also been evaluated and discussed in relation to complex formation. The infrared spectra of both the systems, pyridine–phenol and quinoline–phenol, have been also recorded for various concentrations at room temperature (35 °C) and found to be useful for understanding the presence of N⋯HO bond complexes and the strength of molecular association at specific concentrations.     

Solubility of benzene in aqueous solutions ofmyo-inositol

Solubilities of benzene in aqueous solutions of myo-inositol have been obtained at 15, 25, 35, and 45°C. Large ‘salting-out’ effects are observed, indicating that the inositol is as effective as the common strong electrolytes in decreasing the solubility of benzene. The results are intepreted by a simple model involving the hydration number of inositol as an adjustable parameter. Hydration numbers varying from 14.4 at 15°C to 9.1 at 45°C are reported.     

Excess enthalpies of binary and ternary mixtures of acetonitrile with methanol,ethanol and benzene

Excess molar enthalpies are measured for the binary mixtures methanol—acetonitrile and ethanol—acetonitrile at 25 and 35°C and for the ternary mixtures methanol—acetonitrile—benzene and ethanol—acetonitrile—benzene at 25°C using an isothermal dilution calorimeter. The binary results are well reproduced with an association model which contains four equilibrium constants for the association of alcohol, two equilibrium constants for that of acetonitrile, and two solvation equilibrium constants between alcohol and acetonitrile molecules. The ternary results are compared with those calculated from the model with binary parameters.     

Boosting Benzene Oxidation with a Spin-State-Controlled Nuclearity Effect on Iron Sub-Nanocatalysts

A fundamental understanding of the nature of nuclearity effects is important for the rational design of superior sub-nanocatalysts with low nuclearity, but remains a long-standing challenge. Using atomic layer deposition, we precisely synthesized Fe sub-nanocatalysts with tunable nuclearity (Fe₁–Fe₄) anchored on N,O-co-doped carbon nanorods (NOC). The electronic properties and spin configuration of the Fe sub-nanocatalysts were nuclearity dependent and dominated the H₂O₂ activation modes and adsorption strength of active O species on Fe sites toward C−H oxidation. The Fe₁-NOC single atom catalyst exhibits state-of-the-art activity for benzene oxidation to phenol, which is ascribed to its unique coordination environment (Fe₁N₂O₃) and medium spin state (t_2g⁴e_g¹); turnover frequencies of 407 h⁻¹ at 25 °C and 1869 h⁻¹ at 60 °C were obtained, which is 3.4, 5.7, and 13.6 times higher than those of Fe dimer, trimer, and tetramer catalysts, respectively.     

Catalytic activity of iron-containing polymers in hydroxylation of benzene with hydrogen peroxide

Hydroxylation of benzene with hydrogen peroxide in aqueous acetonitrile at 50°C was studied. The KU-2-8 and KU-1 cation exchangers, and also specially synthesized cation exchangers and phenolformaldehyde resins derived from pyrocatechol and resorcinol, all modified with Fe(III) cations, were used as catalysts. The macrocomplex KU-2-8/Fe³⁺ showed the highest catalytic activity and ensured 32% yield of phenol in 15 min. The formation of phenol depends in a complex fashion on the initial concentration of hydrogen peroxide, content of Fe(III) ions in the polymer, and reaction time.     

Unperturbed dimensions of poly(ethylene oxide)

The intrinsic viscosities of fractions of poly(ethylene oxide) in the molecular weight range 1.5 × 10³ to 10⁶ have been measured at 25°C in benzene, carbon tetrachloride, and acetone; at 35°C in 0.45M aqueous potassium sulfate; and at 50°C in methyl isobutyl ketone and diethylene glycol diethyl ether. The latter three are practically theta solvents. The value of (r₀² /M)^1/2 for poly(ethylene oxide) is calculated to be 0.84 Å from the molecular weights of the high molecular weight fractions, and their intrinsic viscosities in the theta solvents and acetone. Erroneous values result if the usual methods of determination are applied to the data obtained for the low molecular weight (<10⁴) fractions or to the intrinsic viscosities in the very good solvents, benzene and carbon tetrachloride.     

A fast mixing flow system: The kinetics of carbonic acid dehydration in aqueous acid solutions between 20 and 40°c

A simple and inexpensive optical stopped-flow apparatus which includes a springpowered driving system and a very efficient two-stage mixer is described. The total dead-time is less than 2.5 ms. The apparatus has been tested by studying the kinetics of carbon dioxide formation from hydrogencarbonate on mixing with hydrochloric acid, at pH 3–5 and 20–40°C. The average rate constants found for this process are 15.4, 25.1, 42.7, 70.3 and 110.7 s^-1 at 20°, 25°, 30°, 35° and 40°C, respectively. The calculated activation energy is 17950 cal mol^-1. The values are compared with earlier data.     

Polymerization of vinyl acetate retarded by 4-methyl-2,6-di-tert-butylphenol: Kinetic and ESR studies

4-Methyl-2,6-di-tert-butylphenol strongly retards the free radical polymerization of vinyl acetate initiated by azobisisobutyronitrile. The chain transfer constant, estimated from rate data, is 0.020 ± 0.004 at 35°C and does not vary significantly with temperature. Molecular weight data lead to transfer constants of 0.023, 0.020, and 0.024 at 35, 45, and 55°C, respectively. A mean kinetic isotope effect of 9.8 ± 1.0 is observed for the phenol deuterated at the OH group, showing that the main attack of poly(vinyl acetate) radicals on the phenol involves hydrogen abstraction from this group. The activation energy for hydrogen abstraction is estimated to be 7.8 kcal/mole, and the rate constant at 50°C is 160 ± 40 1./mole-sec. The stationary concentration of 4-methyl-2,6-di-tert-butylphenoxyl in the polymerization mixture is proportional to the phenol concentration and is independent of the initiator concentration, as shown by electron spin resonance studies. Cross termination of poly(vinyl acetate) and phenoxy radicals occurs to a greater extent than mutual termination of these radicals. The rate constant for cross termination is close to 1 × 10⁸ 1./mole-sec at 50°C; the activation energy for cross termination is 2.9 ± 1.3 kcal/mole.     

Substituent effects in pi-pi interactions: sandwich and T-shaped configurations

Sandwich and T-shaped configurations of benzene dimer, benzene-phenol, benzene-toluene, benzene-fluorobenzene, and benzene-benzonitrile are studied by coupled-cluster theory to elucidate how substituents tune pi-pi interactions. All substituted sandwich dimers bind more strongly than benzene dimer, whereas the T-shaped configurations bind more or less favorably depending on the substituent. Symmetry-adapted perturbation theory (SAPT) indicates that electrostatic, dispersion, induction, and exchange-repulsion contributions are all significant to the overall binding energies, and all but induction are important in determining relative energies. Models of pi-pi interactions based solely on electrostatics, such as the Hunter-Sanders rules, do not seem capable of explaining the energetic ordering of the dimers considered.     

Bioactive Penta-Coordinated Diorganotin(Iv) Complexes of Pyridoxalimine Schiff Bases

Abstract

Diorganotin(IV) complexes of an extended system derived from the condensation of pyridoxal hydrochloride with 2-amino phenol (H₂L¹), 2-amino-4-methyl phenol (H₂L²), 2-amino-4-chloro phenol (H₂L³), 2-amino-4-nitro phenol (H₂L⁴), 1-amino-2-naphthol hydrochloride (H₂L⁵) have been synthesized by the reaction of dichlorodiorganotin(IV) in a 1:1 molar ratio with these ligands. Spectral studies (IR, ¹H, ¹³C, ¹¹⁹Sn NMR) along with physical data evidenced the formation of penta-coordinated species with the ligands acting as tridentate (ONO) with oxygen occupying the axial positions, and nitrogen at one of the equatorial positions. The ligands and their organotin complexes have been evaluated for antimicrobial activity against phytopathogenic fungi Candida albicans and Aspergillus niger at 25 ± 1 °C and bacteria Bacillus subtilis, Escherichia coli, and Staphylococcus aureus at 37 ± 1 °C. The activities of the ligands have been enhanced on complexation and the results indicate that they exhibit significant antimicrobial properties.

Supplemental materials are available for this article. Go to the publisher's online edition of Phosphorus, Sulfur, and Silicon and the Related Elements to view the free supplemental file.     

La formation de la plupart des composes aromatiques produits lors de la pyrolyse du phenol,ne fait pas intervenir le carbone porteur de la fonction hydroxyle

The thermal cracking of phenol 1-¹⁴C and of phenols tritiated in specific positions has been studied at atmospheric pressure between 665 and 865°C, with a contact time of 2·5 seconds, suggesting the most probable reactions occuring during the thermal cracking. All the aromatic compounds, except benzene and to a less extent toluene, obtained by thermal cracking of phenol, are not produced by conservation of the aromatic ring, but by an intermediate structure C₁₀H₁₂ derived from the condensation of two C₅ fragments. The results have shown that the carbon atom carrying the hydroxyl function is always the one eliminated in forming the C₅ fragment.     

Use of the magnetic suspension balance for the study of polymersolutions

The method involves the isothermal gravimetric determination of the absorption of an organic vapour into a thin film of liquid polymer spread upon an inert particulate support. Results are presented for the absorption of benzene and cyclohexane at 25°C in poly (dimethylsiloxane), and the concentration variation of the interaction parameter determined is compared with that found by other workers.The determination of the partial molar enthalpy of mixing was also examined by studying the absorption of hexane in poly (dimethylsiloxane) over the temperature range of 25 to 35°C, and comparing the value obtained with published values.     

Effect of solvent nature on the catalytic activity of iron-containing pyrocatecholsulfonic cationite in the reactions of H<Subscript>2</Subscript>O<Subscript>2</Subscript> decomposition and benzene hydroxylation

Kinetics of hydrogen peroxide decomposition under the conditions of heterogenous catalysis with iron-containing pyrocatecholsulfonic cationite at 50°C in dimethyl sulfoxide, tetrahydrofuran, dioxane, acetonitrile, and nitromethane was studied. The value of rate constant of hydrogen peroxide decomposition in these solvents was found to diminish with increase of solvent nucleophilicity. At the hydroxylation of benzene in the aqueous acetonitrile medium the formation of phenol was observed. The phenol yield was found to depend on the composition of the binary solvent acetonitrile-water.     

Radiolysis of phenol in aqueous solution at elevated temperatures

γ-Radiolysis and pulse radiolysis of phenol in aqueous solution up to supercritical condition have been carried out. G-values of phenol consumption and product formation have been determined. While dihydroxybenzenes were major products at room temperature, multi-ring compounds and benzene were formed above 300 °C. This indicates reaction mechanism was changed above 300 °C, where phenoxyl radical plays a predominant role. This is supported by the observation of phenoxyl radical in pulse radiolysis. In supercritical water, the G-values increased with decrease of density.     

Synthesis of photosensitive and thermosetting poly(phenylene ether) based on poly[2,6‐di(3‐methyl‐2‐butenyl)phenol‐co‐2,6‐dimethyl‐phenol] and a photoacid generator

A chemically amplified photosensitive and thermosetting polymer based on poly[2,6‐di(3‐methyl‐2‐butenyl)phenol (15 mol %)‐co‐2,6‐dimethylphenol (85 mol %)] ( 3c ) and a photoacid generator [(5‐propylsulfonyloxyimino‐5H‐thiophen‐2‐ylidene)‐(2‐methylphenyl)acetonitrile] was developed. Poly[2,6‐bis(3‐methyl‐2‐butenyl)phenol]‐co‐2,6‐dimethylphenol)] ( 3 ) with high molecular weights (number‐average molecular weight ～ 24,000) was prepared by the oxidative coupling copolymerization of 2,6‐di(3‐methyl‐2‐butenyl)phenol with 2,6‐dimethylphenol in the presence of copper(I) chloride and pyridine as the catalyst under a stream of oxygen. The structures of 3 were characterized with IR, ¹H NMR, and ¹³C NMR spectroscopy. 3 was crosslinked by a thermal treatment at 300 °C for 1 h under N₂. The 5% weight loss temperatures and glass‐transition temperatures of the cured copolymers reached around 420 °C in nitrogen and 300 °C, respectively. The average refractive index of the cured copolymer ( 3c ) film was 1.5452, from which the dielectric constant at 1 MHz was estimated to be 2.6. The resist showed a sensitivity of 35 mJ cm^?2 and a contrast of 1.6 when it was exposed to 436‐nm light, postexposure‐baked at 145 °C for 5 min, and developed with toluene at 25 °C. A fine negative image featuring 8‐μm line‐and‐space patterns was obtained on a film exposed to 100 mJ cm^?2 with 436‐nm light in the contact‐printed mode. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 149–156, 2005     

Mecanismes de fragmentation pyrolytique du phenol et des cresols

The thermal cracking of phenol and ortho and para-cresol at atmospheric pressure, between 665°C and 865°C has been studied with a contact time of 2·5 seconds. ¹⁴C- and ³H-labelled substrates have been used in mechanistic studies of these processes. Elimination of one carbon monoxide produced quasi-exclusively by loss of the carbon of the hydroxyl function of the phenols is the first step and leads to the formation of cyclopentadiene or of a C₅H₆ compound. A condensation of two phenol molecules with loss of water and hydrogen to form dibenzofuran occurs simultaneously. The formation mechanism of this last compound is different according to the cracking temperatures.