Surface Interactions and Fouling Properties of Micrococcus luteus with Microfiltration Membranes

This study was conducted to investigate microbial adhesion of Micrococcus luteus to polypropylene (PP) and polyvinylidene fluoride (PVDF) membranes in relation to the variation of the interfacial energies in the membrane-bacteria systems, for revealing effects of short-range surface interactions on filtration behavior. Both the membranes and M. luteus showed typical strong electron donors and hydrophilic properties. The AB component was dominant in the interfacial energies of the two membrane-bacteria systems. M. luteus presented larger negative U(mlb)(XDLVO) to the PP membrane than to the PVDF membrane. The adhesion experiments also proved that M. luteus had higher adhesion percentage to the PP membrane. This study demonstrated that the adhesion potentials of M. luteus to the PP and PVDF membranes might be explained in terms of bacterium, membrane, and intervening medium surface properties, which are mainly determined by the interfacial energies in the systems according to the XDLVO theory.     

Surface thermodynamics and adhesion forces governing bacterial transmission in contact lens related microbial keratitis

Contact lens induced microbial keratitis results from bacterial transmission from one surface to another. We investigated the adhesion forces of Pseudomonas aeruginosa, Staphylococci and Serratia to different contact lenses, lens cases and corneal surfaces using AFM, and applied a Weibull analysis on these adhesion forces to calculate bacterial transmission probabilities from lens case to corneas with a contact lens as an intermediate. Also a new surface thermodynamic parameter was introduced, the interfacial free energy of transmission, which in essence compares the interfacial free energies of bacterial adhesion, calculated from measured contact angles with liquids on the donating and receiving surfaces in the transmission process. Bacterial adhesion forces were generally strongest among all eight strains for the lens case (-6.5 to -12.0 nN) and corneas (-3.5 to -11.5 nN), while contact lenses (-0.6 to -13.1 nN) exerted slightly smaller adhesion forces. Consequently, bacterial transmission from lens case to contact lens yielded a smaller contribution in the final transmission than from contact lens to cornea. Bacterial transmission probabilities as derived from force analyses were higher when the interfacial free energies of transmission were more negative, which is in line with surface thermodynamic principles. Therewith this parameter could provide useful in analyzing other bacterial transmission phenomena between donating and receiving surfaces as well.     

Microbial‐induced synthesis of mineralization products based on the capture of carbon dioxide: Characteristics,reaction kinetics,interfacial adhesion properties,and mechanism of action

As a new type of green environment‐friendly cementitious material, microbial‐induced mineralization products have garnered more and more attention. In this paper, the synthesis of mineralization products under microbial inducement was conducted. The composition and microstructure of mineralization products were studied using energy‐dispersive spectrometer (EDS), X‐ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscope (TEM). The results showed that mineralization products were calcite, while the shape was similar to globular type, and particle size was about 5 μm. The effect of microbial culture solution, secretion solution, and concentration on the conductivity of the solution was compared and analyzed. During the formation of mineralization products, bacterial bodies not only played the role of nucleation sites but also accelerated the deposition of mineralization products. Thus, it could be seen that the bacterial bodies had a certain influence on the reaction kinetics. The adhesion force of mineralization products was evaluated by the interfacial adhesion properties between the mineralization products and glass slides. The results of the sonication test and scratch test indicated that the interfacial adhesion strength between mineralization products and glass slides was closely related to the mass of mineralization products deposited. The larger the mass of mineralization products deposited, the greater the interfacial adhesion strength. Based on the above research and analysis, the reaction process and mechanism model of microbial‐induced mineralization were defined.     

Microbeam analysis applied to adhesion, surfaces and interfaces

Typical applications of microbeam surface analysis techniques of XPS and ToF-SIMS in adhesion research are being described. Three areas of endeavour are identified as being important in the use of surface analysis in adhesion research; the assessment of surface cleanliness prior to the adhesion process; the forensic analysis of interfacial failure surfaces; probing the interfacial chemistry of adhesion. Examples, chosen from work in the author’s laboratory, are used to illustrate the levels of information that may be attainable from both model systems and from fully formulated, commercial, systems using these techniques. It is concluded that both XPS and ToF-SIMS have important roles to play in adhesion research and for a complete picture of interfacial chemistry and subsequent failure both must be employed.     

Influence of coupling agent chain lengths on interfacial performances of carbon fiber and polyarylacetylene resin composites

The influence of chain lengths on interfacial performances of carbon fiber/polyarylacetylene composites was studied. For this purpose, four coupling agents, methyltrimethoxysilane, propyltrimethoxysilane, octyltrimethoxysilane and dodecyltrimethoxysilane, were grafted onto fiber surface to obtain different chain lengths. The resulting carbon fiber surface was characterized by XPS and dynamic contact angle test. Interfacial adhesion in the resulting fiber reinforced polyarylacetylene resin composites was also evaluated by fracture morphology analysis and interfacial shear strength test. It was found that the interfacial adhesion in composites greatly increased with chain lengths on fiber surface. The improvement of interfacial adhesion was attributed to the interaction between the chain of coupling agents on fiber surface and that of polyarylacetylene resin at the interface. Copyright © 2009 John Wiley & Sons, Ltd.     

Improvement of interfacial adhesion for plasma‐treated aramid fiber‐reinforced poly(phthalazinone ether sulfone ketone) composite and fiber surface aging effects

Interfacial adhesion between the fiber and the matrix in a composite is a primary factor for stress transfer from the matrix to the fiber. In this study, oxygen plasma treatment method was applied to modify the fiber surface for improving interfacial adhesion of aramid fiber‐reinforced poly(phthalazinone ether sulfone ketone) (PPESK) composite. Composite interfacial adhesion properties were determined by interlaminar shear strength (ILSS) using a short‐beam bending test. The composite interfacial adhesion mechanism was discussed by SEM. The changes of chemical composition and wettability for plasma‐treated fiber surfaces stored in air as long as 10 days were investigated by XPS and dynamic contact angle analysis (DCAA), respectively. Results indicated that oxygen plasma treatment was an effective method for improving interfacial adhesion; plasma‐treated fiber surface suffered aging effects during storage in air. Copyright © 2008 John Wiley & Sons, Ltd.     

Quantitative determination of interfacial adhesion in composites with strong bonding

An approach was proposed for the quantitative determination of adhesion strength in composites, in which adhesion is created by other mechanisms than secondary interactions. The approach is based upon a model, which gives debonding stress as a function of interfacial adhesion. Debonding stress was determined by acoustic emission experiments. The mechanism of deformation was checked by SEM experiments and the approach was verified on composites with known interfacial adhesion. The results showed that the use of functionalized polymer in PP/CaCO₃ composites resulted in adhesion strength one order of magnitude larger than without the coupling agent. The application of various surface modification techniques in PP/glass bead composites yielded different adhesion values covering a range of about one order of magnitude. The quantitative determination of interfacial adhesion makes possible the design and optimization of most surface modification techniques in particulate filled and short fiber reinforced composites.     

连续纤维增强含二氮杂萘酮联苯结构聚芳醚砜酮树脂基复合材料的界面

利用射频感性耦合冷等离子体(ICP)处理技术改性连续纤维表面,分别采用X射线光电子能谱(XPS)、原子力显微镜(AFM)及动态接触角分析(DCA)系统研究了等离子体处理时间、放电气压、放电功率等工艺参数对连续碳纤维、芳纶纤维和对亚苯基苯并二噁唑(PBO)纤维的表面化学成分、表面形貌、表面粗糙度及表面自由能的影响.研究结...     

Improving the interfacial property of carbon fiber/PI resin composite by grafting modification of carbon fiber surface

The poor interfacial adhesion between carbon fibers (CFs) and polyimide (PI) resin has seriously hampered the application of CF/PI composites. In this work, the interfacial adhesion was efficiently enhanced by grafting on the CF surface. Surface morphology and surface composition of modified carbon fibers were characterized, which indicated that acrylamide was grafted successfully on the CF surface and the surface roughness was increased slightly. After grafting, the interface shear strength of modified carbon fibers/PI composites was significantly improved by 86.96%, and the interlaminar shear strength was enhanced by 55.61% due to the covalent bonds in interphase and the toughening effect of sizing agent. Moreover, the mechanical properties of composites with different interfacial adhesion were measured, which further confirmed the effect of the grafting modification.     

The influence of surface treatment on the tensile and tribological properties of wood fiber‐reinforced polyimide composite

In this paper, the effect of coupling agent surface treatment of wood fiber on tensile and tribological property of wood fiber‐reinforced thermoplastic polyimide (PI) composites was experimentally investigated. Experimental results revealed that coupling agent surface treatment could effectively improve the interfacial adhesion between wood fiber and PI matrix. Compared with the untreated wood fiber/PI composite, the coupling agent‐treated composite had better interfacial adhesion. The fracture surfaces and worn surface of samples were investigated by scanning electronic microscopy to analyze the effects of surface treatment methods.     

Interfacial studies on the ozone and air‐oxidation‐modified carbon fiber reinforced PEEK composites

In this work, ozone modification method and air‐oxidationwere used for the surface treatment of polyacrylonitrile(PAN)‐based carbon fiber. The surface characteristics of carbon fibers were characterized by XPS. The interfacial properties of carbon fiber‐reinforced (polyetheretherketone) PEEK (CF/PEEK) composites were investigated by means of the single fiber pull‐out tests. As a result, it was found that IFSS (interfacial shear strength) values of the composites with ozone‐treated carbon fiber are increased by 60% compared to that without treatment. XPS results show that ozone treatment increases the amount of carboxyl groups on carbon fiber surface, thus the interfacial adhesion between carbon fiber and PEEK matrix is effectively promoted. The effect of surface treatment of carbon fibers on the tribological properties of CF/PEEKcomposites was comparativelyinvestigated. Experimental results revealed that surface treatment can effectively improve the interfacial adhesion between carbon fiber and PEEK matrix. Thus the wear resistance was significantly improved. Copyright © 2009 John Wiley & Sons, Ltd.     

Polyacrylamide brush coatings preventing microbial adhesion to silicone rubber

Silicone rubber is a frequently used biomaterial in biomedical devices and implants, yet highly prone to microbial adhesion and the development of a biomaterial-centered infection. Effective coating of silicone rubber to discourage microbial adhesion has thus far been impossible due to the hydrophobic character of its surface, surface deterioration upon treatment and instability of coatings under physiological conditions. Here we present a method to successfully grow polyacrylamide (PAAm) brushes from silicone rubber surfaces after removal of low molecular weight organic molecules (LMWOM), such as silane oligomers. PAAm brush coating did not cause any surface deterioration and discouraged microbial adhesion, even after 1-month exposure to physiological fluids. The method presented opens many new avenues for the use of silicone rubber as a biomaterial, without the risk of developing a biomaterial-centered infection.     

Synergistic effects induced by oxy-fluorination of carbon preforms to improve the mechanical and thermal properties of carbon-carbon composites

Oxy-fluorination of carbon preforms with various F₂:O₂ gas mixtures were examined to improve the mechanical and thermal properties of carbon fiber-reinforced carbon composites (C/C composites). The oxy-fluorination of the preforms introduced functional groups onto the preform surface, which improved their thermal properties. Oxy-fluorination also improved the interfacial adhesion of the C/C composites, resulting in increased flexural strength and anti-oxidation. Two synergistic effects of oxy-fluorination on the carbon preform are suggested. One optimizes interfacial adhesion by forming hard chemical bonds and soft electrophilic bonds between the surface functional groups of the oxy-fluorinated carbon preforms and the functional groups of the carbon precursors. The other improves anti-oxidation of the C/C composites by improving the thermal properties of the carbon preform itself and interfacial adhesion which resulted in reducing pores, voids, and interfacial cracks.     

高强聚乙烯纤维的冷等离子体改进

高强聚乙烯纤维的冷等离子体改进金士九，倪亦斌，张佐光（中国科学院化学研究所北京１０００８０）（北京航空航天大学北京）关键词　高强聚乙烯纤维，等离子体，表面改性，界面性能由高强聚乙烯纤维制成的复合材料抗高速撞击（抗弹）性能远远优于芳纶纤维，广泛用作各种...     

Interfacial behavior between atmospheric-plasma-fluorinated carbon fibers and poly(vinylidene fluoride)

Atmospheric-plasma fluorination was used to introduce fluorine functionalities onto the surface of carbon fibers without affecting their bulk properties. The interfacial adhesion between atmospheric-plasma-fluorinated carbon fibers and poly(vinylidene fluoride) (PVDF) was studied by means of direct wetting measurements and single fiber pullout tests. Measured contact angles of PVDF melt droplets on modified carbon fibers show that short exposure times of carbon fibers to atmospheric-plasma fluorination (corresponding to a degree of surface fluorination of F/C = 0.01 (1.1%)) leads to improved wettability of the fibers by PVDF melts. The apparent interfacial shear strength as a measure of practical adhesion, determined by the single-fiber pullout test, increases by 65% under optimal treatment conditions. The improved practical adhesion is not due to the formation of transcrystalline regions around the fibers or a change of the bulk matrix crystallinity or to an increased surface roughness; it seems to be due to the compatibilization of the interface caused of the atmospheric-plasma fluorination of the carbon fibers.     

Tribological properties of poly(phthalazione ether sulfone ketone) composites reinforced with glass fabric modified by graphene oxide depositing

In this paper, by electrophoretic deposition of graphene oxide (GO) on the surface of high‐strength glass fabric, a new fabric/poly(phthalazione ether sulfone ketone) (PPESK) composites material was successfully fabricated. The effects of GO on the interfacial adhesion, interlaminar shear strength, and tribological properties of the composites were investigated. Because of the addition of GO, the interlaminar shear strength of the composites was enhanced by 36.04%. Besides, the scanning electron microscope observation revealed that the interfacial adhesion between PPESK matrix and glass fabric was greatly improved. Attributing to the good interfacial adhesion, the wear‐resistance of the fabric/PPESK composite was greatly enhanced. Moreover, it can be found that the failure location transferred from the interface to the matrix after GO deposition.     

Continuous Atmospheric Plasma Oxidation of Carbon Fibres: Influence on the Fibre Surface and Bulk Properties and Adhesion to Polyamide 12

Continuous atmospheric plasma oxidation (APO) was used to introduce oxygen functionalities to the surface of carbon fibres in an attempt to enhance interfacial adhesion between carbon fibres and polyamide-12 (PA-12). APO only affects the surface properties of the fibres while their bulk properties remained unchanged. Contact angle and ζ-potential measurements demonstrated that APO-treated fibres became significantly more hydrophilic due to the introduction of polar oxygen-containing groups on the fibre surface, which also resulted in an increase of surface energy on the carbon fibres. The interfacial shear strength of single carbon fibre/PA-12 model composites, determined by single fibre fragmentation tests, showed an increase from 40 to 83 MPa with up to 4 min of APO treatment time which confirms that the fibre/matrix interfacial adhesion was enhanced. This highlights that the incorporation of APO into composite manufacturing will allow tailoring of the fibre/matrix interface.     

Adhesion of acrylate-based water dispersion to polypropylene hybrid fabrics

The increase in the content of crosslinking agent and surfactant in acrylate-based water dispersion results in an increase of surface parameters e.g. total SFE and its polar component, interfacial and mechanical work of adhesion of polyacrylate to PP hybrid fabrics. UV irradiation of polyacrylate coating in the course of accelerating ageing has the same effect on surface and adhesive properties as a crosslinking agent or surfactant and leads to a considerable growth of the total SFE, its polar component, interfacial and mechanical work of adhesion. The increase in the interfacial and mechanical work of adhesion with the increase of the crosslinking agent and/or surfactant content in acrylate-based water dispersion is higher for PES/PP fabrics compared to the PA/PP system. The adhesive properties of the film obtained from acrylate-based water dispersion are substantially influenced by the presence of a surfactant and a crosslinking agent.     

Plasma treatment of carbon fiber on the tribological property of polyimide composite

The effect of different ratios of carbon fiber (CF) reinforcing polyimide (PI) and surface treatment of CF on the microstructure and wear resistance of surface layers was studied. The increase of CF content led to a gradual increase in the Interlaminar shear strength (ILSS) values, and the maximum ILSS value arises when the CF content is 15 vol%, with an improvement of 13.45% compared to virgin CF composites. The increased interfacial adhesion could be contributed mainly to the presence of branched PI at the interface region. SEM of the worn surface confirms that the plasma treatment efficiently improves the interfacial adhesion of CF/PI composite. Copyright © 2017 John Wiley & Sons, Ltd.     

Adsorption of Triton X-100 and cetyltrimethylammonium bromide mixture with ethanol at nylon-6–solution interface with regard to nylon-6 wettability: II. Work of adhesion and activity of surfactants at interfaces

On the basis of the values of the surface tension of the aqueous solutions of the Triton X-100 and CTAB mixture with ethanol, the surface tension of nylon-6 and the nylon-6–solution interfacial tension, the activity of the surfactant mixture and ethanol at the nylon-6–solution interface was calculated and compared to that at the solution–air one. For these calculations, the Sprow and Prausnitz equation was applied. The obtained values of the activity were used for the calculations of the work of adhesion of the solution to the polymer surface. The values of the work of adhesion obtained in this way were compared to those determined from the Young–Dupre equation by using the contact angle values of the aqueous solutions of the TX-100 and CTAB mixture with ethanol measured on the nylon-6 surface. The changes of the work of adhesion determined from the Young–Dupre equation were also considered as a function of the surface tension of the solution, its polar component and the interfacial interaction parameter.